Petroleum calibration Standards & reference materials

Specialists in analytical laboratory instrumentation and supplies for the (petro)chemical, food, pharmaceutical, paint and marine industry. Zematra is actively involved in important standardization bodies like ASTM, EI, CEN etc. This enables Zematra to inform her customers about the latest developments in existing methods and advise them of new methods Zematra BV, for more than Petroleum calibration Standards & reference materials Our ranges offers the most comprehensive selection of petroleum standards in the industry. Our petroleum standards are suitable for broad range of analysis Common applications for our single-element, multi-element, and custom- blended products include: - Used oil analysis for predictive engine failure analysis - QC analysis of motor oils and additives formulations - Crude and refined oils - Environment analysis of waste oils - Sulfur in fuels - Foods Oils - Coolants ISO Certifications VHG Labs is now part of LGC Standards, and holds accreditation to ISO 9001, ISO/IEC 17025 and ISO Guide 34, offering our customers the assurance that these certified reference materials (CRM) are manufactured and tested to the fullest extent by a company firmly committed to quality at all levels Our Petroleum Standards: Flash Point, Pour Point, Cloud Point, Freezing Point, Could Filter Plug Point, Distillation, Acid/ Base number, Moisture, Soot Content, Fuel Dilution, Biodiesel and Viscosity Flash Point FP27-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 25 C-35 C 250ml FP53-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 45 C-55 C 250ml FPPM60-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 55 C-65 C 250ml FP70-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 65 C-75 C 250ml FP75-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 70 C-80 C 250ml FP93-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 90 C-100 C 250ml FP114-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 110 C-120 C 250ml FP134-250 Flash Point CRM for ASTM D93 (Pensky Martens Closed Cup Tester), Typical Flash Point Range 130 C-145 C 250ml FP115-250 Flash Point CRM for ASTM D92 (Cleveland Open Cup Tester), Typical Flash Point Range 110 C-120 C 250ml FP138-250 Flash Point CRM for ASTM D92 (Cleveland Open Cup Tester), Typical Flash Point Range 135 C-150 C 250ml FP200-250 Flash Point CRM for ASTM D92 (Cleveland Open Cup Tester), Typical Flash Point Range 190 C-215 C 250ml FP230-250 Flash Point CRM for ASTM D92 (Cleveland Open Cup Tester), Typical Flash Point Range 220 C-240 C 250ml FP40-250 Flash Point CRM for ASTM D56 (Tag Closed Cup Tester), Typical Flash Point Range 40 C-50 C 250ml FP51-250 Flash Point CRM for ASTM D56 (Tag Closed Cup Tester), Typical Flash Point Range 45 C-55 C 250ml FP55-250 Flash Point CRM for ASTM D56 (Tag Closed Cup Tester), Typical Flash Point Range 50 C-60 C 250ml FPTC60-250 Flash Point CRM for ASTM D56 (Tag Closed Cup Tester), Typical Flash Point Range 55 C-65 C 250ml FP67-250 Flash Point CRM for ASTM D56 (Tag Closed Cup Tester), Typical Flash Point Range 60 C-70 C 250ml

Cloud Point C2-250 ASTM D2500 Cloud Point Reference Material, Typical Point Range: -4 C to 0 C 250ml C5-250 ASTM D2500 Cloud Point Reference Material, Typical Point Range: +3 C to +9 C 250ml C10-250 ASTM D2500 Cloud Point Reference Material, Typical Point Range: -12 C to -8 C 250ml C15-250 ASTM D2500 Cloud Point Reference Material, Typical Point Range: -17 C to -13 C 250ml C20-250 ASTM D2500 Cloud Point Reference Material, Typical Point Range: -22 C to -18 C 250ml Pour Point P5-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -7 C to-3 C * 250ml P10-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -12 C to -8 C * 250ml P15-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -17 C to -13 C * 250ml P20-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -22 C to -18 C * 250ml P40-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -42 C to -36 C * 250ml P50-250 ASTM D97 Pour Point Reference Material, Typical Point Range: -53 C to -47 C * 250ml * not intended for use with Phase Instruments Cold Filter Plug Point CFP1-250 ASTM D6371/IP 309 CFPP, Typical Point Range: -20 C to -17 C 250ml Distillation D86-4-500 ASTM D86 Group 4 Distillation Standard 500ml D86-500 ASTM D86 Group 1&2 Synth. Distillation standard 500ml Acid and Base Number AN 0.1-100G Acid number 0.1 mgkoh/g Reference standard in Hydrocarbon Oil 100 gr AN 0.5-100G Acid number 0.5 mgkoh/g Reference standard in Hydrocarbon Oil 100 gr AN 1-100G Acid number 1 mgkoh/g Reference standard in Hydrocarbon Oil 100 gr AN 1.5-100G Acid number 1.5 mgkoh/g Reference standard in Hydrocarbon Oil 100 gr AN 2-50G Acid number 2 mgkoh/g Reference standard in Hydrocarbon Oil 50gr AN 3-50G Acid number 3 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 6-50G Base number 6 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 10-50G Base number 10 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 15-50G Base number 15 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 30-50G Base number 30 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 40-50G Base number 40 mgkoh/g Reference standard in Hydrocarbon Oil 50gr BN 70-50G Base number 70 mgkoh/g Reference standard in Hydrocarbon Oil 50gr

CRM Materials with different product nature, acc Iso 17025 All ROFA Certified Reference Materials meet the precision of ISO 17025. The production is according Guides 31, 34 & 35. Certified by Round Robin Method by independent test laboratories. Order code Test name Value Main Method GASOLINE Bottle Volume DE-GA-514 Density at 15 C 740.1 kg/m3 ASTM D 4052 250 ml Automatic Distillation DI-GA-514 (Unleaded) 32,7 C / 180,2 C ASTM D 86 250 ml VP-GA-514 Reid Vapour Pressure 64,0 kpa ASTM D 323 250 ml BE-GA-514 Benzene Content 0.795 % vol ASTM D 4053 250 ml AC-GA-514 Aromatic Content 26.9 % vol ASTM D 5580 250 ml GASOLINE OM-GA-095 Motor Octane Number E95 (Unleaded) 85,9 ASTM D 2700 1000 ml OR-GA-095 Research Octane Number E95 (Unleaded) 97,2 ASTM D 2699 1000 ml GASOLINE OM-GA-098 Motor Octane Number E98 (Unleaded) 87,5 ASTM D 2700 1000 ml OR-GA-098 Research Octane Number E98 (Unleaded) 98,9 ASTM D 2699 1000 ml JET AVIATION Fuel DE-KR-444 Density at 15 C 792,7 kg/m3 ASTM D 4052 250 ml FR-KR-444 Freezing Point - 50.2 C ASTM D 2386 250 ml DI-KR-444 Automatic Distillation 149 C / 256 C ASTM D 86 250 ml SU-KR-444 Sulphur of Mercaptans 3.13 mg/kg ISO 3012 250 ml AD-KR-444 Acidity 0.0016 mgkoh/g ASTM D 3242 250 ml FI-KR-444 FIA Aromatics 19,3 % Vol ASTM D 1319 250 ml AB-KR-444 Abel Flash Point 40.6 C IP 170 250 ml VI-KR-444 Kinematic Viscosity -20 C 3.558 mm²/s ASTM D 445 250 ml FT-KR-444 TAG Flash Point 41.7 C ASTM D 56 250 ml SP-KR-444 Smoke Point 24.4 mm ASTM 1322 250 ml AP-KR-444 Aniline Point 58,9 C ASTM D 611 250 ml DIESEL DE-GO-350 Density at 15 C 833,8 kg/m3 ASTM D 4052 250 ml CP-GO-350 Cloud Point - 6,4 C ASTM D 2500 250 ml PP-GO-350 Pour Point -24.0 C ASTM D 97 250 ml DI-GO-350 Automatic Distillation 164 C / 360 C ASTM D 86 250 ml PM-GO-350 Pensky Martens Flash Point 60,2 C ASTM D 93 -A 250 ml VI-350+20 Kinematic Viscosity +20 C 3,963 mm²/s ASTM D 445 250 ml VI-350+40 Kinematic Viscosity +40 C 2,591 mm²/s ASTM D 445 250 ml FA-GO-350 FAME Content B=6.5% Volume EN 14078 250 ml SU-GO-350 Sulphur Content 7,10 mg/kg ASTM D 5453 250 ml

Order code Test name Value Main Method Bottle Volume CF-GO-209 DIESEL Cold Filter Plugging Point -23.6 C EN 116 / IP 309 250 ml DIESEL SU-GO-555 Sulphur Content 7,2 mg/kg EN 116 / IP 309 250 ml DIESEL FA-GO-919 FAME Content B=3% Volume EN 14078 250 ml DIESEL DE-GO-888 Density at 15 C 836,39 kg/m3 ASTM D 4052 250 ml CP-GO-888 Cloud Point - 3,3 C ASTM D 2500 250 ml PP-GO-888 Pour Point -16.1 C ASTM D 97 250 ml CN-GO-888 Cetane Number 52,6 ASTM D 613 1000 ml LUBRICANT PM-LU-456 Pensky Martens Flash Point 203 C ASTM D 93 250 ml LUBRICANT DE-LU-671 Density at 15 C 868,7 kg/m3 ASTM D 4052 250 ml FC-LU-671 Cleveland Flash Point 268 C ASTM D 92 250 ml PM-LU-671 Pensky Martens Flash Point 247 C ASTM D 93 250 ml PP-LU-671 Pour Point -11.6 C ASTM D 97 250 ml Moisture KF-BLK-100 Karl Fischer Titration Reference Standard in 10W30 Motor Oil 0.0 wt.% H2O KF-0.05P-100 Karl Fischer, nominal water conc. 0.05% in 10W30 motor oil KF-0.1P-100 0.1 wt.% H2O in 10W30 motor oil KF-0.5P-100 0.5 wt.% H2O in 10W30 motor oil KF-1.0P-100 1 wt.% H2O in 10W30 motor oil CT-BLK-100 Crackle Test Reference Standard in 10W30 Motor Oil 0.0wt.% H2O CT-0.05P-100 Crackle Test Reference Standard 0.05 wt.% H2O in 10W30 motor oil CT-0.1P-100 Crackle Test Reference Standard 0.1 wt.% H2O in 10W30 motor oil CT-0.5P-100 Crackle Test Reference Standard 0.5 wt.% H2O in 10W30 motor oil CT-1.0P-100 1 wt.% H2O in 10W30 motor oil Soot Content SOOT-BLK-50 Soot Content Standard in 15W40 Diesel Oil Blank 50ml SOOT-A-50 Soot Content Standard in 15W40 Diesel Oil 0.5-wt% 50ml SOOT-B-50 Soot Content Standard in 15W40 Diesel Oil 2-4wt% 50ml SOOT-C-50 Soot Content Standard in 15W40 Diesel Oil 4-6wt% 50ml SOOT-D-50 Soot Content Standard in 15W40 Diesel Oil 6-9wt% 50ml SOOT-E-50 Soot Content Standard in 15W40 Diesel Oil 9-12wt% 50ml SOOT-SET Soot Content Standard SET in 15W40 Diesel Oil 6x50ml

Fuel dilution DSLFD-BLK-100 Devolatilized Diesel Fuel in 75 cst Base oil DSLFD-2P-100 2% (v/v) Devolatilized High Cetane Diesel Fuel (10% lights removed) in 75 cst Hydrocarbon Oil DSLFD-4P-100 4% (v/v) Devolatilized High Cetane Diesel Fuel (10% lights removed) in 75 cst Hydrocarbon Oil DSLFD-5P-100 5% (v/v) Devolatilized High Cetane Diesel Fuel (10% lights removed) in 75 cst Hydrocarbon Oil DSLFD-10P-100 10% (v/v) Devolatilized High Cetane Diesel Fuel (10% lights removed) in 75 cst Hydrocarbon Oil GASFD-BLK-100 Devolatilized Diesel Fuel in 75 cst Base oil (OIL-75) GASFD-2P-100 2% (v/v) Devolatilized Gasoline (10% lights removed at 160F) in 75 cst Hydrocarbon Oil. Bottled in a 100 ml Wide Mouth Glass Bottle For Use with GC, IR or Flash Point GASFD-5P-100 5% (v/v) Devolatilized Gasoline (10% lights removed at 160F) in 75 cst Hydrocarbon Oil. Bottled in a 100 ml Wide Mouth Glass Bottle For Use with GC, IR or Flash Point GASFD-10P-100 10% (v/v) Devolatilized Gasoline (10% lights removed at 160F) in 75 cst Hydrocarbon Oil. Bottled in a 100 ml Wide Mouth Glass Bottle For Use with GC, IR or Flash Point Biodiesel Standards Metals in biodiesel B100M5-5-100G Multi Element Biodiesel Standard in B100 Biodiesel 5µg/g, Ca,K,Mg,Na,P 100g B100M5-10-100G Multi Element Biodiesel Standard in B100 Biodiesel 10µg/g, Ca,K,Mg,Na,P 100g B100M5-20-100G Multi Element Biodiesel Standard in B100 Biodiesel 20µg/g, Ca,K,Mg,Na,P 100g B100-BLK-100 Biodiesel, B100-BLK-500 Biodiesel, 500ml 500ml Sulfur in Biodiesel SB100-5-100 Sulfur @ 5µg/g in B100 Biodiesel SB100-10-100 Sulfur @ 10µg/g in B100 Biodiesel SB100-15-100 Sulfur @ 15µg/g in B100 Biodiesel SB100-20-100 Sulfur @ 20µg/g in B100 Biodiesel SB100-25-100 Sulfur @ 25µg/g in B100 Biodiesel SB100-50-100 Sulfur @ 50µg/g in B100 Biodiesel SB100-100-100 Sulfur @ 100µg/g in B100 Biodiesel SB100-500-100 Sulfur @ 500µg/g in B100 Biodiesel B100-BLK-100 Biodiesel, B100-BLK-500 Biodiesel, 500ml 500ml Micro Carbon Residue Tester 5073122 ASTM D4530 MCRT low Carbon Residue Ref, 0,3%, Cert 1 bottle 5073130 ASTM D4530 MCRT Low Carbon Residue Ref, 2%, Cert 1 bottle 5073123 ASTM D4530 MCRT Medium Carbon Residue Ref, 10,6%, Cert 1 bottle 5073124 ASTM D4530 MCRT High Carbon Residue Ref, 24,0%, Cert 1 bottle

Biodiesel/ Diesel Fuel Blend BDBLEND-2P-20 2% Biodiesel / 98% High Cetane Diesel Fuel v/v 20ml BDBLEND-5P-20 5% Biodiesel / 95% High Cetane Diesel Fuel v/v 20ml BDBLEND-10P-20 10% Biodiesel / 90% High Cetane Diesel Fuel v/v 20ml BDBLEND-15P-20 15% Biodiesel / 85% High Cetane Diesel Fuel v/v 20ml BDBLEND-20P-20 20% Biodiesel / 80% High Cetane Diesel Fuel v/v 20ml BDBLEND-25P-20 25% Biodiesel / 75% High Cetane Diesel Fuel v/v 20ml BDBLEND-30P-20 30% Biodiesel / 70% High Cetane Diesel Fuel v/v 20ml BDBLEND-100P-20 100% Biodiesel 20ml BDBLEND-BLK-20 100% High Cetane Diesel Fuel 20ml Foam Tendency Foam Tendency according ASTM D892 & ASTM D6082 F-100 Test Sequence I, II & III, Temperature range 24 C & 93,5 C 950ml F-200 Test Sequence II & IV, Temperature range 93.5 C & 150 C 950ml RPVOT Reference Oil RPVOT Reference Oil ASTM D 2272 QMR Nominal Break time in Minutes 794 minutes 950ml QHR Nominal Break time in Minutes 1244 minutes 950ml Viscosity All Cannon viscosity standards meet the precision of ASTM D445/446 and ISO 3104/3105, and are traceable to the NIST (National Institute of Standards and Technology) Cannon Viscosity standards are manufactured and/or certified in Cannon ISO 9001/2000 registered and A2LA accredited laboratory. A2LA has accredited Cannon for technical competence in the field of calibration (certificate number 1262.01). the accreditation includes the determination of kinematic and dynamic viscosity (including that of viscosity standards and customer samples) in accordance with ISO/IEC 17025-1999. All calibration are based on the master viscometer procedures detailed in ASTM D2162 Cannon has been delegated by NIST to provide U.S. national measurement standards and to issue calibration and measurement certificates for certified liquid viscosity reference standards. Cannon supplies viscosity standards in a variety of container sizes. The default container size for most standards is the 500ml bottle. Standards are also available in 120ml, 1 liter and 3,8 liter (1 Gallon)

Viscosity Standards Catalog number Viscosity standard 20 C 25 C 37.78 C 40 C 50 C 60 C 80 C 100 C 9727-C10 N.4Ɨ 0,32 0,3 0,28 0,27 9727-C15 N.8Ɨ 0,64 0,6 0,52 0,51 9727-C20 N1.0Ɨ 0,93 0,86 0,72 0,7 0,62 9727-C22 N2 2,2 2 1,6 1,5 1,3 0,85 0,65 9727-C25 S3 3,9 3,3 2,5 2,4 1,9 1,2 0,9 9727-C27 N4 5,2 4,5 3,3 3,1 2,5 1,4 1,1 9727-C30 S6 10 8 5,3 5 3,8 2 1,5 9727-C31 N7.5 11 9,5 6,3 5,9 4,5 2,4 1,7 9727-C32 N10 21 16 9,5 8,8 6,3 2,9 2 9727-C34 N14 24 20 12 11 8,2 3,8 2,6 9727-C35 S20 37 29 17 15 11 4,6 3 9727-C36 N26 47 37 22 20 14 6,2 4 9727-C37 N35 75 56 30 27 18 7,1 4,4 9727-C38 N44 92 71 39 36 24 9,5 5,9 9727-C40 S60 141 104 52 47 30 10 6,2 9727-C41 N75 160 125 68 61 41 16 9,2 9727-C42 N100 283 202 95 84 52 16 9,2 9727-C43 N140 340 250 130 120 74 25 14 9727-C45 S200 460 330 160 145 90 25 14 9727-C46 N250 650 480 230 210 130 41 23 9727-C47 N350 830 600 280 250 150 40 24 9727-C48 N415 1200 830 390 350 210 62 33 9727-C50 S600 1500 1100 490 440 260 75 40 9727-C51 N750 2200 1600 710 620 370 100 53 9727-C52 N1000 2900 2000 800 460 280 120 65 9727-C53 N1400 4300 3000 1200 680 420 180 92 9727-C55 S2000 7300 4700 1700 1400 700 140 59 9727-C56 N2500 7100 5100 2100 1200 780 350 180 9727-C57 N4000 17000 11000 2900 1400 730 250 100 9727-C58 N5100 25000 16000 4500 2100 1100 360 140 9727-C60 S8000 33000 20000 7000 5900 2800 450 200 9727-C61 N10200 52000 32000 9000 4200 2100 660 250 9727-C62 N15000 68000 41000 11000 5400 2600 840 320 9727-C63 N18000 92000 57000 16000 7500 3800 1140 420 9727-C65 S30000 71000 23000 20000 9300 1400 540 Ɨ Incurs additional shipping charges due to low flash point.

High Viscosity Standards Dynamic Viscosity in mpa s (cp) Kinematic Viscosity mm2/s (cst) Catalog number Viscosity standard 20 C 25 C 40 C 60 C 135 C 60 C 100 C 135 C 9727-E10 N600 1100 160 15 200 22 9727-C52 N1000 2900 2000 800 280 350 80 9727-E15 N2000 4900 380 21 440 26 9727-C57 N4000 17000 11000 2900 730 850 120 9727-E20 N8000 20000 1400 1600 9727-C62 N15000 68000 41000 11000 2600 3000 360 9727-E25 N30000 120000 80000 4700 5400 9727-E27 N62000 200000 13000 1600 9727-E29 N150000 420000 24000 3000 9727-E30 N190000 840000 520000 140000 33000 4000 9727-E35 N450000 1600000 100000 9727-E40 N2700000 5300000 340000 9727-E42 N2700000SP dynamic Shear Rheometer (DSR) standard at 52,58, 64, 70 & 76 C. Low Temperature Viscosity Standards For Low Gear Temperature Gear Oils (SAE 70W, 75W, 80W & 85W) Also ATF fluid ASTM D2983 Catalog number Viscosity standard Approximate Viscosity in mm2/s (cst) /mpa s (cp) except where noted -55 C -40 C -34 C -29 C -26 C -25 C -23 C -20 C -18 C -12 C -10 C -7 C 0 C 9727-G10 N27B 24000 12000 6100 4500 3500 2000 9727-G12 N27C 45000 22000 12000 8000 6100 3500 9727-G15 N115B 160000 120000 75000 37000 20000 12000 9727-G25 N60B 150000 9727-G30 N120B 150000 9727-G35 N480B 150000 9727-G40 N1400B 150000 9727-G45 N2B* 8mm2/s 9727-G50 N74B 3400 9727-G55 N38B 4200 9727-G60 N25B 8000 9727-G65 N14B 17000 * Incurs additional shipping charges due to low flashpoint

For Cannon Mini Rotary Viscometer (CMRV) ASTM D3829 and ASTM D4684 Catalog Viscosity Approximate Viscosity number standard 9727-T10 N105B 30.000mPa.s (cp) at -20 C; CMRV Viscosity standard 56.200mPa.s (cp) at -25 C, CMRV Viscosity standard 9727-T20 YS-30 Exhibits yield stress of 70 Pa ±35 Pa at -30 C 9727-T25 YS-35 Exhibits yield stress of 70 Pa ±35 Pa at -35 C For High Temperature High Shear Viscometer (HTHS) measurement at 150 C and 10⁶s shear rate ASTM D 5481 Dynamic Viscosity in mpa s (cp) Catalog number Viscosity 100 C 150 C standard 9727-U45 HT22 3.5 1.5 9727-U50 HT39 4.7 2.0 9727-U55 HT75 7.0 2.7 9727-U60 HT150 10.5 3.7 9727-U65 HT240 15.4 5.0 9727-U70 HT390 23.5 7.0 9727-U92 HTNN-1 3.6* 9727-U94 HTNN-2 3.1* * Non- Newton standard Data at 10-6s-1

Cannon CCS Viscosity standards Cannon CL Standards provide certified dynamic viscosity data (in cp or mpa.s) at temperatures from - 5 C to -35 C. these standards are used to calibrate the CANNON Cold Cranking Simulator (CCS) oil testing. ASTM D5293 and SAE Specification J300. Viscosity standard range from CL80 till CL740, totally a range of 27 values. Optional or as set of 8/18pcs. Catalog number Viscosity Standard -5 C -10 C -15 C -18 C -20 C -25 C -30 C -35 C -40 C 9727-N02 CL080 850 1430 9727-N04 CL090 1150 1930 9727-N06 CL100 875 1450 2450 9727-N07 CL110 1030 1680 2880 9727-N08 CL120 775 1230 2050 3580 9727-N09 CL130 975 1550 2600 4580 9727-N10 CL140 675 775 1300 2080 3550 6380 9727-N11 CL150 950 1530 2500 4310 7830 9727-N12 CL160 1000 1200 1900 3200 5580 10300 9727-N13 CL170 850 1330 2180 3650 6430 12000 9727-N14 CL190 1080 1400 1680 2750 4680 8380 15900 9727-N16 CL200 875 1330 2130 3500 6030 10900 21100 9727-N18 CL220 1030 1600 2050 2550 4230 7380 13600 9727-N20 CL240 1230 1900 3050 5180 9100 16900 9727-N22 CL250 1380 2180 2880 3500 6000 10700 20000 9727-N24 CL260 1680 2650 4300 7300 13100 9727-N26 CL280 2030 3200 4330 5280 9080 16500 9727-N28 CL300 2430 3880 6480 11300 20700 9727-N30 CL320 3000 4850 6600 8150 14300 9727-N31 CL340 3480 5650 9580 17000 9727-N32 CL380 2650 4180 6800 9300 11600 20800 9727-N33 CL420 4930 8180 14000 9727-N34 CL480 3780 6000 10100 13700 17400 9727-N35 CL530 7500 12500 2200 9727-N36 CL600 5700 9300 15700 20300 9727-N37 CL680 11300 19400 9727-N38 CL740 7650 12600 9727-N42 Set of 8 Set of CCS Low Temp Standards includes CL140, CL 190, CL220, CL250, CL280, CL320, CL480 & CL740 9727-N43 Set of 18 Set of CCS 2050/2100/2100LT Low Temp Standards includes CL080, CL090, CL100, CL110, CL120, CL130, CL140, CL150, CL160, CL190, CL220, CL250 (2x), CL280, CL320, CL380, CL480 & CL600.

Certified Colour Reference Standards Oils, Fuels and Chemicals Lovibond Reference Liquids AOCS-Tintometer - ASTM Color Gardner - Lovibond RYBN- PT-Co/Hazen/APHA - Saybolt Ideal for routine calibration of colour measuring instruments & verification of test data Ensure good inter-laboratory and inter-instrument correlation Applications in statistical quality control (SQC) and statistical process control (SPC) High stability standards with a guaranteed 12-month shelf-life Full traceability to internationally recognised standards - ASTM, Gardner & Saybolt Colour standards certified to ISO 17025 - AOCS-Tintometer, Lovibond RYBN & Pt-Co Colour certified under ISO 9001 quality system All classified as non-hazardous according to EU directives Each bottle supplied with full certification including MSDS Colour Scale AOCS- Tintometer Colour (AOCS Cc 13j-97, Cc 13b-45) ASTM Color (ASTM D6045, D1500) Gardner Colour (ASTM D1544, D6166) Lovibond RYBN Colour (AOCS Cc 13j-97) Platinum-Cobalt Colour (ASTM D1209) Saybolt Colour (ASTM D6045, D156) Nominal Certified Value Order Code Accreditation Standard 0.3R 2.0 Y (5¼ ) 134240 ISO 9001 1.0R 9.0 Y (5¼ ) 134250 ISO 9001 1.2R 12.0 Y (5¼ ) 134260 ISO 9001 2.2R 22.0 Y (5¼ ) 134270 ISO 9001 3.6R 28.0 Y (5¼ ) 134280 ISO 9001 0.4 (<0.5) 134290 ISO 17025 1 134000 ISO 17025 3 134010 ISO 17025 5 134020 ISO 17025 2 134200 ISO 17025 5 134210 ISO 17025 8 134220 ISO 17025 0.8R 2.0Y 0.1N (5¼ ) 134080 ISO 9001 1.4R 4.0Y 0.5N (5¼ ) 134090 ISO 9001 2.0R 7.0Y 0.5N (5¼ ) 134100 ISO 9001 2.1R 11.0Y 0.5N (5¼ ) 134110 ISO 9001 2.5R 14.0Y 0.7N (5¼ ) 134120 ISO 9001 3.1R 22.0Y 0.8N (5¼ ) 134130 ISO 9001 3.3R 33.0Y 0.1N (5¼ ) 134230 ISO 9001 5 mg Pt/l 134140 ISO 9001 10 mg Pt/l 134150 ISO 9001 15 mg Pt/l 134160 ISO 9001 30 mg Pt/l 134170 ISO 9001 50 mg Pt/l 134180 ISO 9001 100 mg Pt/l 134190 ISO 9001 500 mg Pt/l 462803 ISO 17025-10 134040 ISO 17025 0 134050 ISO 17025 +12 134060 ISO 17025 +25 134070 ISO 17025

Conostan Oil Analysis Standards CONOSTAN products are used extensively in the calibration and operation of analytical instruments for the analysis of elements in oil and other organic fluids. CONOSTAN is the only source of multi-element metalorganic standards in the history of the National Institute of Standards & Technology (NIST). The variety of products afford convenience as reference and routine analytical materials for ICP, DCP, Rotating Disc Electrode (RDE), XRF, AA, and other analytical spectrometer techniques. CONOSTAN products are optimized for: Compatibility: 33 elements can be combined over an extensive concentration range - Viscosity: Viscosity range at room temperature is ideal for instrumental applications. - Instrumental Response: Excellent analytical response over a wide range of analytical applications. - Shelf life: All CONOSTANR element standards and spectroscopy products have a one year minimum shelf life from the date of shipment. Single element standards in oil Single-element CONOSTANR standards are especially useful for atomic absorption and X-ray fluorescence determinations. The matrix oil for these standards is high purity hydrocarbon oil with a 17 cst viscosity at 40 C and flash point of 175 C (20 Blank Oil). They are available at the following metal concentrations. The 1000 and 5000 ppm standards can be used as a source of single-element calibration standard for your specific applications using all types of spectroscopic methods of analysis. Multi-element standards in oil Multi-element Conostan standards are especially useful for ICP, RDE, and DCP analysis of metals in oil. They are available in high purity hydrocarbon oil solutions and are blended to approximately 70 cst viscosity at 40 C and flash point of 215 C (75 Blank Oil). They contain equal amounts of each element. Concentrations not listed are available as custom multi-element standards on request. You may create your own S-21 and S-12 standards by adding additional elements to the stocked product standards. CONOSTAN Biodiesel standards A new line of CONOSTANR biodiesel standards for the analysis of metals and sulfur in biodiesel fuel. Manufactured in accordance to ASTM methods D7039, D6751, D5453 and EN14214 for ICP and XRF analysis. Complete with a certificate of analysis. Standards according ASTM Methods for petrochemical analysis by GC Biodiesel fuel calibration standards (ASTM D6584, EN 14105:2003) Oil companies and vehicle manufacturers are actively working with biofuel extender producers to have agreed standards for esterified vegetable oils suitable for blending with conventional diesel to ensure that the product meets the technical requirements of modern diesel engines. The minimum test requirements for biodiesel blend extenders are specified in ASTM D6751 in USA and EN14214 within Europe. At present a limit of 5% FAME is allowed in diesel and this 5% must conform to the EN14214 standard. Both ASTM D-6751 and EN 14214 specify the use of ASTM Method D-6584 for glycerin determination.

ASTM D 6584 standard solutions This test method covers the quantitative determination of free and total glycerin in B-100 methyl esters by gas chromatography. The range of detection for free glycerin is 0.005 to 0.05 mass %, and total glycerin from 0.05 to 0.5 mass %. This procedure is not applicable to vegetable oil methyl esters obtained from lauric oils, such as coconut oil and palm kernel oil. U-RGO-310-1 ASTM D-6584 Standard Solution 1ml Solvent: Pyridine Diolein 50 μg/ml Monoolein 100 μg/ml Glycerol 5 μg/ml Triolein 50 μg/ml EN 14105:2003 standard solutions Free and total glycerol and mono-, di-, tri-glyceride content Method EN 14105 is used to determine glycerin and total glycerine in fatty acid methyl esters (FAME) used in biodiesel products. Samples are derivatized, then analyze U-RGO-300-1 EN 14105:2003 Standard Solution 1ml Solvent: Pyridine Butanetriol 80 μg/ml Glycerol 5 μg/ml Tricaprin 800 μg/ml 1,3-Diolein 50 μg/ml Monoolein 250 μg/ml Tiolein 50 μg/ml ASTM Method D2887 Boiling range distribution of petroleum fractions by GC Method D2887 covers the determination of the boiling range distribution of petroleum products. The test method is applicable to petroleum products and fractions having a final boiling point of 538 C (1000 F) or lower at atmospheric pressure as measured by this test method. The test method is limited to samples having a boiling range greater than 55 C (100 F), and having a vapor pressure sufficiently low to permit sampling at ambient temperature. U-ASTM-110-1 ASTM Method D2887 Column Test Mixture 1ml n-hexane 6 % (w/w) n-dodecane 12 % (w/w) n-octacosane 1 % (w/w) n-heptane 6 % (w/w) n-tetradecane 12 % (w/w) n-dotriacontane 1 % (w/w) n-octane 8 % (w/w) n-hexadecane 10 % (w/w) n-hexatriacontane 1 % (w/w) n-nonane 8 % (w/w) n-octadecane 5 % (w/w) n-tetracontane 1 % (w/w) n-decane 12 % (w/w) n-eicosane 2 % (w/w) n-tetratetracontane 1 % (w/w) n-undecane 12 % (w/w) n-tetracosane 2 % (w/w) ASTM Method D3710 Boiling range distribution of gasoline and gasoline fractions by GC Method D3710 covers the determination of the boiling range distribution of gasoline and gasoline components. The test method is applicable to petroleum products and fractions with a final boiling point of 500 F (260 C) or lower. U-ASTM-100-1 ASTM Method D3710 Calibration Mixture 1ml 2-Methylbutane 10 % (v/v) Toluene 12 % (v/v) n-dodecane 4 % (v/v) n-pentane 8 % (v/v) n-octane 5 % (v/v) n-tridecane 2 % (v/v) 2-methylpentane 6 % (v/v) p-xylene 14 % (v/v) n-tetradecane 2 % (v/v) n-hexane 6 % (v/v) n-propylbenzene 5 % (v/v) n-pentadecane 2 % (v/v) 2,4-Dimethylpentane 6 % (v/v) n-decane 4 % (v/v)

ASTM Method D4815 MTBE, ETBE, TAME, DIPE, tertiary-amyl alcohol and C1 to C4 alcohols in gasoline Method D4815 covers the determination of ethers and alcohols in gasolines by gas chromatography. U-RGO-422-1 ASTM D4815 Quantitative Peak ID Mixture 1ml Methanol 7.30 % (w/w) n-butyl alcohol 7.30 % (w/w) Ethyl alcohol (Ethanol) 7.30 % (w/w) tert-amyl methyl ether (TAME) 7.30 % (w/w) Isopropyl alcohol (Isopropanol) 7.30 % (w/w) 1,2-Dimethoxyethane (DME) 6.00 % (w/w) tert-butanol 7.30 % (w/w) Benzene 5.00 % (w/w) 1-Propanol 7.30 % (w/w) Methylcyclopentane 4.00 % (w/w) sec-butanol (2-Butanol) 7.30 % (w/w) tert-dutylmethyl ether (MTBE) 4.00 % (w/w) Isobutyl alcohol 7.30 % (w/w) Isopropyl ether 4.00 % (w/w) tert-pentanol (tert-amyl alcohol) 7.30 % (w/w) tert-butyl ethyl ether (ETBE) 4.00 % (w/w) For the Conostan, single and multi-element, reference materials as for the ASTM Petrochemical standards for GC applications, there are lots of variety possible, ask for the possibility what Zematra can offer.