New X Series Centaurs In-grade CSA Listed Wet Label IP68 CX 2/14
C1X In-Ground LED Fixture IP68. Cast stainless steel body 304 alloy. 1W Cree XPE LED. On-board electronics for 24V DC and 0-10V dimming. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class II, not suitable for fountain or pool use.. Requires remote 24V Dc power supply. Available in RGB with remote DMX controller Series Lamp Wattage Body Color Temp. Optic Ballast Lens Options C1X L-LED 1L-1x1W 3000K LED 4-Fully recessed SS-Stainles Steel 0- None X-120vAC-24vDC T-CLR. Temp Glass 0-None 3L-1x1W 5000K LED Note: Other color available w/cond. entries 1-6 Degree Spot Remote Driver 2-25 Degree Flood Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes Note: On board 0-10v Dimming K-Internally Ceramic Coated Tempered Glass G-Frosted Toughened Glass Power Supplies SERIES DRIVER PART # DESCRIPTION WATTAGE UNITS POWERED SPECIAL DETAILS C1X PPLT00155 120VAC-24VDC 30W 1W 24vDC w/ integral 0-10v dim 1 to 24 parallel PPLT00157 120VAC-24VDC 60W 1W 24vDC w/ integral 0-10v dim 1 to 48 parallel PPLT00158 120VAC-24VDC 100W 1W 24vDC w/ integral 0-10v dim 1 to 80 parallel
Staten Island 911 Memorial Lighting Consultant: Fisher, Marantz, Stone Fixture: C1X
. Cast stainless steel body 304 alloy. 1W Cree XPE LED. On board electronics for 24V DC and 0-10V Dimming. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class II, not suitable for fountain or pool use.. Requires remote 24V Dc power supply. Available in RGB with remote DMX controller C2X In-Ground 24V Dimmable LED Fixture IP68 Remote Driver Series Lamp Wattage Body Finish Optic Ballast Lens Options C2X L-LED 1L-1x1W 3000K LED 4-Recessed Box w/ SS-Stainless Steel 0- None X-Remote 24vDC T-Clear Temp Glass 0-None 2L-1x1W 4000K LED 4L-1x3W 3000K LED 5L-1x3W 4000K LED Conduit Entries Transformer Required K-Internally Ceramic Coated G-Frosted Tempered Glass Power Supplies Note: Other colors available on request 1-10 Degree Narrow 2-21 Degree Medium 3-39 Degree Wide 4-10x44 Degree Elliptical Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes Note: On board 0-10v Dimming C2X PPLT00155 120VAC-24VDC 30W 1W 24vDC w/ integral 0-10v dim 1 to 10 parallel 1 LED/UNIT 3w 24vDC w/ integral 0-10v dim 1 to 6 parallel PPLT00157 120VAC-24VDC 60W 1W 24vDC w/ integral 0-10v dim 1 to 19 parallel 3w 24vDC w/ integral 0-10v dim 1 to 13 parallel PPLT00158 120VAC-24VDC 100W 1W 24vDC w/ integral 0-10v dim 1 to 32 parallel 3w 24vDC w/ integral 0-10v dim 1 to 22 parallel
. Cast stainless steel body 304 alloy. 1W Cree XPE LED. On board driver for 120V. Non dimming. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class II, not suitable for fountain or pool use. C2G In-Ground 120V LED Fixture IP68 Integral Driver Series Lamp Wattage Body Finish Optic Ballast Lens Options C2G L-LED 1L-1x1W 3000K LED 4-Fully recessed SS-Stainless Steel 0- None G-Integral T-Clear Temp Glass 0-None 3L-1x1W 5000K LED w/cond. entries Driver 120vAC K-Internally Ceramic Coated G-Frosted Tempered Glass Note: Other colors available on request. 1-10 Degree Narrow 2-21 Degree Medium 3-39 Degree Wide 4-10x44 Degree Elliptical Note: LED Optics are for use with 'T' clear glass lens. They are not intended for 'K' or 'G' Lenes
. Cast stainless steel body 304 alloy. 3x 3W Cree XPE LED. On board electronics for 24V DC and 0-10V dimming. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class II. Requires remote power supply C4X In-Ground 24V Dimmable LED IP68 Remote Driver Series Lamp Wattage Body Finish Optic Ballast Lens Options C4X L-LED 1R-3x1W White 3000K 4-Recessed Box w/ SS-Stainless Steel 0- None Q-Remote 24vDC T-Clear Temp Glass 0-None 2R-3x1W White 4000K conduit entries 1- Narrow (6 ) Driver Required J-Flash White BTM & 3R-3x3W White 3000K 3- Wide (25 ) (Int. 0-10V Dim.) Non-Skid Top Pattern 4R-3x3W White 4000K 4- Elliptical (6 x25 ) K-Flash White BTM & Other colors available upon request Remote Driver Clear Top G-Internally Frosted Power Supplies to be ordered separately Toughened Glass Q-Non-Skid Top Patterned Tempered Glass C4X PPLT00155 120VAC-24VDC 30W 1W 24vDC w/ integral 0-10v dim 1 to 6 parallel 3w 24vDC w/ integral 0-10v dim 1 to 2 parallel 3 LED'S PER PPLT00157 120VAC-24VDC 60W 1W 24vDC w/ integral 0-10v dim 1 to 13 parallel UNIT 3w 24vDC w/ integral 0-10v dim 1 to 5 parallel PPLT00158 120VAC-24VDC 100W 1W 24vDC w/ integral 0-10v dim 1 to 22 parallel 3w 24vDC w/ integral 0-10v dim 1 to 8 parallel
. Cast stainless steel body 304 alloy. 3 x1w Cree XPE LED. On board power supply for 120-277V. Non-dimming. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Integral power supply. Class II, not suitable for fountain or pool use.. Available anti slip dot pattern glass lens C4G In-Ground 120-277V LED Fixture IP68 Integral Driver Series Lamp Wattage Body Finish Optic Ballast Lens Options C4G L-LED 1R-3x1W White 3000K 4-Recessed Box w/ SS-Stainless Steel 0- None C-120-277vAC Int. T-Clear Temp Glass 0-None 2R-3x1W White 4000K conduit entries 1- Narrow (6 ) Non-Dimming J-Flash White BTM & Note: Other colors available on request. 3- Wide (25 ) Elect. Driver Non-Skid Top Pattern 4- Elliptical (6 x25 ) K-Flash White BTM & Clear Top G-Internally Frosted Toughened Glass Q-Non-Skid Top Patterned Tempered Glass
. Cast stainless steel body 304 alloy. Cree MCE LED. On board 24vDC with DMX interface individually controlled. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class II, not suitable for fountain or pool use. Available anti slip dot pattern glass lens. DMX channels are not field addressable without specialized equipment. If addresses are not specified, the fixture will default to address 1 (1-red, 2-green, 3-blue, 4-white). C4C In-Ground LED Fixture IP68 Remote Integral Driver Series Lamp Wattage Body Finish Optic Ballast Lens Options C4C L-LED 3K-5W RGBW LED 4-Recessed Box w/ SS-Stainless Steel 0- None X-Remote 24vDC T-Clear Temp Glass 0-None 4K-5W Dynamic White conduit entries 1- Narrow (6 ) Power Supply Req'd J-Flash White BTM & 2- Med (30 ) (INT DMX INTERFACE) Non-Skid Top Pattern K-Flash White BTM & Note: Integral 24vDC Driver Board along with individually controlled DMX interface Clear Top G-Internally Frosted Toughened Glass Q-Non-Skid Top Patterned To be used with Tempered Glass Remote Power Supply. Power Supplies C4C PPLT00155 120VAC-24VDC30W 4.6w 24vDC w/ int. DMX interface 1 to 4 parallel 1 CREE MCE PPLT00157 120VAC-24VDC 60W 4.6w 24vDC w/ int. DMX interface 1 to 9 parallel per unit PPLT00158 120VAC-24VDC 100W 4.6w 24vDC w/ int. DMX interface 1 to 16 Parallel
C7X In-Ground Fixture Flat Trim IP68. Cast stainless steel body 304 alloy. 6x 1W Cree XPE LED. Integral power supply for 120V non-dimming. Available in MR16 12V DC halogen with integral power supply. Walkover, drive over rated for 11,000 lbs at 30 mph. Cast stainless steel 304 alloy junction box. Silicone rubber anti siphon outlet box gasket. Remote power supply. Class I. Available anti slip dot pattern glass lens Series Lamp Wattage Body Finish Grill Ballast Lens Options C7X 6-Halogen 14-37W MR16 NSP10 4-Fully Recessed SS-Stainless Steel 1- STD T-120V-12V Elect. G-Internally Frosted 0-None L-LED 15-37W MR16 NSP25 W/ Cond. Entries Integral Trans. Toughened Glass 9-HID 16-37W MR16 FL40 J-277V-12V Elect. Integral Trans. U-Non Skid Temp Glass T-Clear Temp Glass C-120V-277V Elect. Integral Trans. 1F-1Wx6 Ring 3K White LED AM-1Wx6 Ring 5K White LED 2F-1Wx6 Ring Red LED 3F-1Wx6 Ring Blue LED 4F-1Wx6 Ring Green LED 5F-1Wx6 Ring Cyan LED 6F-1Wx6 Ring Amber LED AG-20W MH GE MR16 Spot 3000K AH-20W MH GE MR16 Flood 3000K Note: MR16 Lamps mounted to adjustable swivel bracket tilt max 15 off vertical. Note: Halogen is either T or J. LED is always C and comes standard with 0-10V dimming. HID metal halide is always C.
. Cast stainless steel body 304 alloy. Xicato 1300lm LED module with integral driver for 120-277V w/ 0-10V Dimming or. 20W MR16 MH adjustable with integral ballast. Walkover, drive over rated for 11,000 lbs at 30 mph. Class I. Available anti slip dot pattern glass lens CDX In-Ground Fixture Flat Trim IP68 Series Lamp Wattage Body Finish Grill Ballast Lens Options CDX 9-HID AG-20W MH GE MR16 Spot 3000K 4-Fully Recessed SS-Stainless Steel 1- STD C-120-277V Integral T-Clear Temp Glass 0-None L-LED AH-20W MH GE MR16 Flood 3000K W/ Cond. Entries Electronic Q-Non Skid Temp Glass W-Linear Spread FB-39W MH GE MR16 Spot 3000K L-120-277V w/ Integral Patterened Q-Honeycomb FC-39W MH GE MR16 Flood 3000K 0-10V Dimming Louver EX-1300lm Xicato 3000K S-Solite Lens EY-1300lm Xicato 3500K Ballast 'C' HID Only B-Special Lens EZ-1300lm Xicato 4000K Ballast 'L' LED Only (see drawing) AG, AH, FB, FC HID Only EX, EY, EZ LED Only Note: Options added to rubber holder.
Drawings C1X C2X
Drawings C2G C4X
Drawings C4G C4C
Drawings C7X CDX - LED
General Installation Instructions 11/2/07 FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID WARRANTY LOCATION INSTALLATION RISK OF ELECTRICAL SHOCK. THIS EQUIPMENT IS TO BE INSTALLED BY A QUALIFIED ELECTRICIAN ONLY. MAKE CERTAIN ELECTRICAL SUPPLY CIRCUIT IS DE-ENERGIZED BEFORE BEGINNING INSTALLATION. CHECK FIXTURE LABEL FOR CORRECT VOLTAGE. READ ALL INSTRUCTIONS CAREFULLY. This model is designed for concrete pour installation. The upper edge of the housing must be flush with the prepared surface into which it is recessed. Do not install fixture in a manner that creates a pocket where water can sit on top of fixture. Not suitable for use in places where the luminaire is likely to be exposed to a horizontal stress load caused by braking, acceleration or change of direction. 1. Lighting fixture comes fully assembled. Note: When not working on fixture replace trim ring for site safety and to protect fixture components from moisture and damage. Keep each trim ring with the original body it was supplied on. Note: Use care to protect O-ring on trim ring. Do not remove, loosen, cut, deform or otherwise disturb O-ring. Keep O- ring clean and dry. 2. Set fixture in desired location. Position the fixture in such a manner that the conduit/cable is not stressed at the entry point to the light fixture. 3. The foundation on which the luminaire is to be installed must correspond to the maximum permissible pressure load of the luminaire. Suitable drainage must also be provided. Level the body in two horizontal planes using the three leveling tabs around outer body. The upper edge of the housing must be flush with the prepared surface into which it is recessed. UNDER NO CIRCUMSTANCES MAY IT BE LOWER! 4. Unthread lens assembly from body with tool provided. Ensure that all internal surfaces of the fixture are kept completely dry during installation. Pry out the accessory gasket by using a screw driver. Carefully by hand remove reflector. 5. Connect incoming leads to quick disconnect plug. GREEN WIRE TO GROUND, CONNECT BLACK FIXTURE TO BLACK BUIDLING WIRE AND CONNECT WHITE FIXTURE WIRE TO WHITE BUILDING WIRE. Replace tray, lamp, and reflector. Make sure that no wires have been damaged. 6. If using conduit entries, the entries must be sealed with Dap Heavy Duty Kwik Foam (not provided). The foam should be sprayed from inside the fixture up into the conduit. Failure by the contractor to use the DAP product could cause a void in the warranty. Replace tray with lamping. If not using through wiring, plug second conduit entry with 3/4" conduit plug. Please make sure wet label requirements are meet. 7. Install lamp and adjust if necessary. Tighten all screws to assure the lamp will not shift after aiming is acquired. Replace reflector and accessory gasket. 8. Place lens frame over fixture ensuring that there is no foreign matter between the lens frame and the body. Start the lamp and bring luminaire to operating temperature (20 to 30min.), this will evaporate the moisture content of air to be trapped. Once operating temperature has been reached, carefully thread the trim assembly to body with tool provided.