Sales Administration Use Only LCG stock 435989-001 601346-601360 9-15-2017 Quote Number Quote Revision Shop Order Number Serial Number(s) Date Customer : Salesperson : Model Part / Drawing Number : 1720-9202-2017 : ST 9200 19LCG C5, Standard Duty Petroleum Trailer CUSTOMER FURNISHED TRACTOR DATA REQUIRED Weights to Include Driver, Fuel, Tools, Equipment, etc. If none is provided, the following tractor data will be used: Front Axle Weight: 9200 lbs Rear Axle Weight: 7000 lbs Fifth Wheel Height: 49.5 Set Ahead: Adjustable Wheel Base: 190 Other Information: Enable Track Changes on the Review Tab to identify deviation from the Base Model Specification A. VESSEL A1. Shell Material Aluminum - 5454 alloy. All sizes/gauges are nominal. Top: 0.180in front section, 0.192in center section, 0.180in rear section Sides: 0.180in Bottom: 0.200in A2. Shell and Head Finish A3. Shape Drain Troughs: Shell: Bright Front Head: Bright Rear Head: Bright *Polish rear head after production Elliptical, 19.59 GPI *Trough in all compartments. A4. Specification DOT 406 A5. Vapor Testing Tested at 5 PSI rated at 3.3 PSI. Vapor tested and certified to EPA Method 27-CA Air Resources Board standards and manholes sealed. A6. Nominal Capacity 9,200 gallons plus 3% outage. 60 gallons is the minimum outage for any size compartment. A7. Compartments 5 Compartments, front to rear 3000/1500/1100/1000//2600 Page 1 of 8
A8. Bulk Heads Aluminum - 5454 alloy. All sizes/gauges are nominal. Configuration: Front: Rear: Compartments: *Double head between #4 and #5, single heads between all other compartments. 0.201in stiffened and shoed 0.201in stiffened and shoed 0.201in unstiffened A9. Surge Heads Aluminum - 5454 alloy. All sizes/gauges are nominal. All surge heads are dished & flanged with (1) 20" man way center, (2) 12" drain holes 6 and 12 o'clock, and (2) 3" emergency drain holes @ 3 and 9 o'clock. Over Kingpin: Over Rungear: Middle of Tank: 0.201in stiffened and shoed 0.185in stiffened and shoed 0.185in unstiffened A10. Flashing Full length, double leg extrusions. Dams front and rear with transverse overturn protection rails as required by code. A11. Documentation Computer generated calibration charts 1/2" increments. HM-183 documentation w/markings on front head. Vapor test decal with documentation. Unit hydrostatically tested. *Chevron Exhibit C form with trailer. A12. Operating -20 F to 180 F Temperature A13. Lading Gasoline, Diesel Fuel, or similar A14. Miscellaneous None B. TANK FITTINGS AND PIPING B1. Manholes (1) 16" Civacon Aluminum offset manhole per compartment. Includes PV Valve,10 aluminum vent, and Buna N gaskets. Meets HM 183 and CFR49 178.364-10 venting requirements. B2. Capacity Indicators Indicator Rods: Additional Discs: If ordered, each capacity indicator rod will come with one disc. Additional discs may be ordered. None None B3. Internal Ground (1) 1/8" stainless steel static ground wire per compartment, attached at top and bottom. *Connect ground wire with bolts at each end. Page 2 of 8
B4. Venting DOT406 venting in manhole. B5. Cleanouts/ Fill Covers None B6. Vapor Recovery Vent Location: Materials: B7. Vapor Recovery Connection B8. Vapor Recovery Piping (1) 3" Civacon air operated inward opening sequential vent per compartment. Located in each manhole cover. Aluminum vent with stainless trim & Viton seats. Black Nylon vapor recovery nipple connected to flashing rail A hose connects the vapor recovery vent to the nylon vapor recovery nipple 4" Aluminum Internal vapor line from flashing rail through mid-tank. Line to continue to the following locations: (1) curbside outlet 15" to rear of last discharge valve. (4" outlet). (1) curbside outlet 15 front of discharge (4" outlet). *(1) curbside outlet to rear of rear head. (4in outlet). (Turn vapor outlet down approximately 15 degrees for easy access). B9. Vapor Recovery Fittings *(3) 4in Poppeted adapter and dust cap on each vapor outlet. All vapor adapters are eight (8) bolt TTMA flange mounted and located per API RP 1004, where applicable. B10. Additional Venting None B11. Emergency Valve (1) 5 x 4, Max Air II with internal cylinder, EV per compartment Materials: Aluminum body with Teflon seat. Splash shield-vortex breaker over each EV. To simplify piping, a straight valve may be used in place of an elbow style. B12. Operator System Civacontrol II air control kit includes master control push/pull incorporated into air distributor. Location: *Mounted in overfill cabinet attached to 48 cabinet. One emergency trip located street side, front of tank. B13. Piping/Piping Gasket 4" Schedule #10 aluminum discharge piping with large radius formed sweeps to curbside of tank, located per API standards. Page 3 of 8
Flanged: Grooved: Grooved: Viton gaskets on flanged piping connections Dixon Aluminum couplers on groove-groove connections Baylast gaskets on groove-groove connections B14. Discharge Valve (1) 4" Civacon 891A openable adapter per compartment, no sight glass. B15. Discharge Accessories Materials: Aluminum handle and Viton seals (3) Civacon 4" API to 4 dual cam style hose adapters and caps. (2) API dust caps, includes retaining cable. *Ethanol sight glasses on outlets, includes flanges, hardware and Viton gaskets. WARNING: Heil Trailer International no longer provides warranty for sight glasses or gasket materials used for the installation of sight glasses. B16. Streetside None Discharge B17. Pump Off-Line None B18. Overfill System *Civacon ROMLINK onboard Overfill Monitor with molded wire loom. Monitor includes air over electric switch to indicate the vents are open prior to monitor receiving permit light. Monitor Location: Probe: Location: Socket: Socket Location: Mounted in overfill cabinet. (1) CivaStar top probe per compartment Installed in manhole cover *Civacon dual sockets SJ6W and SJ6S with ground verification device in sockets. *Locate sockets in overfill cabinet. *VIP Chip for overfill system. *Locate components in overfill cabinet as follows top to bottom: Civacontrol II air control kit ROMLINK monitor Overfill plugs Page 4 of 8
*Set up so overfill cabinet door will close air control valve. B19. Brake Interlock Safety interference bar with lock down pin handle over discharge valves and vapor outlet(s). Activates (1) brake interlock valve. Rear vapor outlet to have separate brake interlock valve. B20. Overfill Interlock *Air/Electric(Hobbs) switch on rear most vapor outlet B21. Miscellaneous *Trucknology product ID tag at each discharge head. (Unleaded Regular, Unleaded Mid- Grade, Unleaded Premium, Ethanol, Diesel, Kerosene, Vapor, Empty). C. ACCESSORIES C1. Ladder *Front, walk through aluminum ladder, center of head, with serrated rungs and platform top step and integral grab handles. C2. Walkway Adhesive backed, skid-resistant tape between flashing rails. *Walkway drains via internal rear aluminum pipe drains, through tank. C3. Hose Carriers (1) Hose Tray with reduced center, (8) Heavy duty straps, w/tee handle and hook Size: Material: Location: 4.5 x 22 Wide, Full Length with reduced center. Aluminum, reinforced on ends for extended wear Curbside C4. Stick Tube *2" x 21-foot (sch. 10) aluminum calibration stick tube. Mounted on outriggers on curbside near rear. Front open with removable pin. Rear capped with drain hole. C5. Cabinets *(1) 48in W x 30in H x 28in D, 2-door Location: Mounted curbside forward of tandem. *(1) 20"W x 30"H x 9"D overfill cabinet, 1-door with "C" hinge. Location: Mount on discharge side of 48" cabinet. Hinge door on left side of cabinet. * C style hinges for 48 cabinet. (2). Page 5 of 8
C6. Splash Guard Front and rear, HEIL, anti-sail, anti-spray flaps. C7. Fenders (1) Single contour front fenders, streetside (1) Double contour rear fenders, streetside C8. Placards\Doc. Holders *Betts PS-1 Certificate Holder Location: Locate on street side at landing leg. *(4) Label Master #80SM "Slidemaster" single piece placard holders and brackets. Mounted front, rear and one each side at mid-tank. C9. Lights 12 Volt Truck Lite flange mount LED lamp system complying to FMVSS with conspicuity markings each side and rear. Combination mid-tank clearance and turn signals, one each side One oval third stop light, located rear center of trailer near bottom of rear head. (2) Aluminum light boxes at rear, one each side of tank. *(1) Peterson (800 lumens) LED swivel spot light. Mounted on EVO cabinet to illuminate work area. *LED dome lights mounted above discharge area. Includes (2) lights on common switch in Overfill cabinet. *(3) 33203R Dual function lights to function with brake lights, (ilo std.). Triple ID light bar. Three conductor harness required for each. Wire each 33203R light in rear dam to the clearance circuit and the stop circuit. C10. Wiring (1) 7 way ATA (#SAE J560) connector in nose box Located at lower streetside front head 12 Volt system, 7 wire, molded conduit throughout All connections made in junction boxes C11. Miscellaneous *Combination cone/bucket holder mounted near landing leg c/s. D. CHASSIS *1" black vinyl numerals on brackets at each discharge head denoting compartment sizes. D1. Upper Fifth Wheel Hi-tensile steel, bolted and adjustable with 2" forged kingpin. D2. Skid Plate Aluminum skid plate. Page 6 of 8
D3. Landing Legs D4. Landing Legs Finish SAF Atlas 55 2-speed, sealed gear box with arctic grade grease, 55,000 lbs. rated lift capacity with 10 x 12 swivel type sand shoes, street side crank, and 8 hole mtg bolt pattern. Black Armor finish for improved durability. D5. Suspension Heil s value package includes Hendrickson AANT 23K air ride suspension & brake system, 71.5" track 5.75 diameter axle, parallel spindle, 23,000 lb. beam rating, 49" spacing, with single leveling valve. D6. Suspension Finish Suspension Towers, Galvanized. Integrated axle painted Imron Gray D7. Suspension Frame Suspension sub frame, standard width. Suspension bolted to sub frame with electrolysis barrier. Bumper: (RIG) Underride: D8. Suspension Frame Finishing Aluminum DOT compliance bumper per FMVSS223 Underride is typically not required per wheels back exemption; however, it will be added if required by suspension location. Natural aluminum surface finish. D9. Brake System Aluminum tank air system meeting FMVSS 121 requirements ECU: Configuration: Glad Hands: Constant Power: WABCO RSS 4S/2M ABS with Roll Stability 16.5" x 7" (quick change) S-cam type drum brake system Philips Quick Release glad hand on service line. Auxiliary, blue circuit, center pin of SAE J560 7-way. D10. Brake Chamber OEM type 30-30 long stroke parking-emergency spring brake D11. Brake Lining OEM HXS brake lining D12. Slack Adjuster OEM slack adjuster D13. Drums (4) Centrifuse OEM - outboard mount brake drums (16.5" x 7"). D14. Axles (2) Integrated with air ride D15. Paint *Paint all steel parts grey. D16. Accessories None Page 7 of 8
D17. Miscellaneous None E. WHEEL END E1. Warranty Hendrickson HXL7 warranty package with ADI hubs, includes 7-year wheel end warranty; requires grease, solid caps,precision320 Nut System, and premium bearings and seals. E2. Hubs (4) ADI 10 Stud, hub pilot (single nut mount) hub for outboard drum. Hub is e-coated for corrosion resistance. E3. Oil Seals OEM bearings with premium oil seals F. WHEELS F1. Wheels *(4) 10 stud Alcoa Ultra One 8.25" x 22.5" aluminum wheels with clean buff finish on inside positions. *(4) 10 stud Alcoa Ultra One 8.25" x 22.5" Polished aluminum wheels on outside positions. G. TIRES G1 Tires *Goodyear Marathon LHT 11R22.5 tires. (14-ply). H. MISCELLANEOUS H1. Customer Supplied Parts See product definition catalog for acceptable customer supplied parts. H2. Trailer Warranty Heil s Value Package includes: Heil Trailer Silver Warranty Package. H3. Notes Operational manual and information CD is included and shipped with each trailer. H4. Other None Page 8 of 8