Instruction Sheet P/N 079A Optional Nozzles for Versa-Spray and Versa-Spray II Guns Description A wide variety of nozzles are available for Versa-Spray and Versa-Spray II powder spray guns. Manual and automatic guns are shipped with different types of nozzles. All nozzles listed in this instruction sheet can be used on any manual or automatic Versa-Spray or Versa-Spray II gun. Nozzle Type Shipped With Flat-Spray automatic guns Conical manual guns Flat-Spray Nozzle Selection An identification groove appears in one of two locations on all flat-spray nozzles: Identification Groove Location Meaning New-style, -mm nozzle. This nozzle is shipped with automatic guns and provides better pattern dispersion and atomization than most other flat-spray nozzles. Old-style, optional nozzles. These optional flat-spray nozzles produce different spray patterns and film builds.
Optional Nozzles for Versa-Spray and Versa-Spray II Guns Flat-Spray Nozzle Selection (contd) Nozzle Spray Pattern Powder Velocity Application.-mm Flat Spray High Large, flat surfaces -mm Flat Spray Medium-high Fine finish on flat surfaces -mm Flat Spray Medium-low Touch up -mm Flat Spray Low Reinforcement 0 Cross-Cut Medium-low Recess reinforcement 90 Cross-Cut Low Deep recesses Castle Medium-low Pin point
Optional Nozzles for Versa-Spray and Versa-Spray II Guns Conical Nozzle and Deflector Selection Deflector Size Used with This Nozzle Spray Pattern mm mm with pattern adjuster Powder Velocity High Application Manual touch-up mm mm with pattern adjuster General finishing 9 mm mm with pattern adjuster Medium Large surfaces 9 mm Short Versa-Spray II Medium Large surfaces mm Short Versa-Spray II Parts with gaps and recesses mm mm with pattern adjuster Mediumhigh Mediumlow Mediumlow Parts with gaps and recesses 8 mm mm Low Large surfaces
Optional Nozzles for Versa-Spray and Versa-Spray II Guns Nozzle Installation WARNING: Turn off the electrostatic voltage and ground the gun electrode before performing the following tasks. Failure to observe this warning could result in a severe shock. NOTE: Before removing nozzles, disconnect the powder feed hose from the pump. Blow out the feed hose, powder inlet body, nozzle extension (if used), and nozzle with low-pressure compressed air. Use a clean, dry cloth to wipe off the remaining powder after removing the nozzle parts. NOTE: Versa-Spray II guns with air do not use a nozzle wear sleeve. Disregard steps and if you have a Versa-Spray II gun with an electrode-cleaning air extension (0).. See Figure. Pull the existing nozzle () straight off the gun.. Pull the wear sleeve () straight off the resistor probe ().. Slide the appropriate wear sleeve () over the resistor probe. Be careful not to damage the electrode ().. Push the conical nozzle (7) into the end of the powder inlet body () or air extension (0).. Slide the pattern adjuster (8) (if used) over the nozzle.. Push the deflector (9) onto the end of the resistor probe. Be careful not to damage the electrode. 7 8 0 7 8 9 Versa Spray and Versa Spray II Guns without Air Versa Spray II Guns with Air 9 Figure Nozzle Installation. Flat-spray nozzle. Wear sleeve (flat-spray nozzle). Powder inlet body. Resistor probe. Electrode. Wear sleeve (conical nozzle) 7. Conical nozzle 8. Pattern adjuster 9. Deflector 0. Air extension
Optional Nozzles for Versa-Spray and Versa-Spray II Guns Parts Flat-Spray Nozzles Item Slot Type Kit P/N mm. mm mm mm 0 Cross-Cut 90 Cross-Cut Castle Nozzle Material Tivar Glass-Filled PTFE (GFT) Kit Includes These Items: Two O-rings () 98 Wear Sleeve (7) 8 with O-ring (8) 9008 0 X X X 0 X X 77 X X 80 X X X 8 X X 7 X X 99 X X X 990 X X 7 X X 997 X X X 990 X X 79 X X 0 X X X 07 X X 0 X X X 0 X X 79 X X X 7877 X X NOTE: These nozzle kits can be used on any Versa-Spray or Versa-Spray II manual or automatic gun. If you have a Versa-Spray II gun with an electrode-cleaning air extension, you do not need to order a nozzle kit that includes a wear sleeve (7) with O-ring (8). 7 8 Figure Flat-Spray Nozzle Parts
Optional Nozzles for Versa-Spray and Versa-Spray II Guns Conical Nozzles and Deflectors -mm Conical Nozzle and Deflectors See Figure. Item Part Description Quantity Note 9 SERVICE KIT, nozzle, mm 7 -mm DEFLECTOR, with O-ring, Tivar 9008 O-RING, silicone, 0.88 x 0. x 0.0 in. 79 ADJUSTER, pattern, mm 8 NOZZLE, -mm dia, with O-rings, Tivar 90 O-RING, silicone,.000 x.88 x 0.09 in. 98 O-RING, silicone, 0.87 x.0 x 0.09 in. 7 8 SLEEVE, wear, conical, Tivar Optional Deflectors 8 -mm DEFLECTOR, Tivar, with O-ring 7880 -mm DEFLECTOR, Tivar, with O-ring 7 9-mm DEFLECTOR, Tivar, with O-ring 9008 O-RING, silicone, 0.88 x 0. x 0.0 in. A NOTE A: This O-ring is included with all deflectors. 7 mm Figure -mm Conical Nozzle and Deflectors
Optional Nozzles for Versa-Spray and Versa-Spray II Guns 7 -mm Conical Nozzle and Deflector See Figure. Item Part Description Quantity Note 70 SERVICE KIT, nozzle, mm 9 8-mm DEFLECTOR, with O-ring, Tivar 9008 O-RING, silicone, 0.88 x 0. x 0.0 in. 789 NOZZLE, -mm dia, with O-rings 98 O-RING, silicone, 0.87 x.0 x 0.09 in. 8 SLEEVE, wear, conical, Tivar mm Figure -mm Conical Nozzle and Deflector Short Conical Nozzle and Deflectors See Figure. Item Part Description Quantity Note 78 9-mm DEFLECTOR, Versa-Spray II, with O-ring 7 -mm DEFLECTOR, Versa-Spray II, with O-ring, Tivar 9008 O-RING, silicone, 0.88 x 0. x 0.09 in. A 79 NOZZLE, short, Versa-Spray II, with O-rings 98 O-RING, silicone, 0.87 x.0 x 0.09 in. 8 SLEEVE, wear, conical B NOTE A: This O-ring is included with all deflectors. B: Use only on guns without air. mm Figure Short Conical Nozzle and Deflectors
8 Optional Nozzles for Versa-Spray and Versa-Spray II Guns Issued /0 Original copyright date 00. Cross-Cut, Nordson, the Nordson logo, and Versa-Spray are registered trademarks of Nordson Corporation. Tivar is a registered trademark of Poly-Hi Corporation.