56314308 SCRUB-N-VAC TOOL KIT For Advenger / BR 600S series Adgressor / BR 850S series AquaRide SE-AXP / BRX 700 X Adhancer R28-C, R32-C CONTENTS OF KIT ITEM PART NO. QTY DESCRIPTION 56040783 1 Instruction Sheet 1 56220035 1 Hose Assembly 2 56314399 1 Coupler 3 56412310 3 Bushing, Stepped 4 56002124 3 Scr, Pan Phil 10-24 x.62 5 56402940 2 Bumper,.812 Sq. NOTE 6 56009205 2 Washer, Flt SS.219 x.50 x.047 7 56314402 1 Wand Assembly 8 56314403 1 Caddy NOTE 9 56407361 6 Clamp NOTE 10# 56009029 12 Scr Panphil Thd Form 10-24 X.50NOTE 11 56314309 1 Pump Assembly (includes items 12-31) 12 56220074 1 Imperial Nipple 1/4 To 1/8 NPT 13 56745543 1 Adapter Blk Hd 1/4 14 56001954 6 Wsh, Flt SAE #10 15 56002674 2 Scr, Pan Phil 10-24 x 1.00 16 56002733 2 Scr, Pan Phil 10-24 x.88 17 56002768 4 Nut, Hex Nyl Loc 10-24 18 56009039 2 Scr, Hex Thd Form 10-24 x.50 19 56052338 2 Grommet 20 56155640 1 Barb, Adapter 3/8 x 1/4NPT 21 56212014 1 Pump, 36VDC 22 56219932 7 Clamp, Hose SAE #6 23 56220055 1 Plug 24 56314432 1 Hose, Spiral.375 x 63.00 25 56900035 2 Barb, 90 Elbow 3/8 x 3/8NPT 26 56314644 1 Weldment, Adapter Plate 27 56315335 1 Tee, Barb 28 56316560 1 Plate, Pump 29 56396330 1 Hose, PVC Clear 2 30 56478523 6 Tie, Cable 31 56755327 1 Hose, Spiral.375 14 # = Revised or new since last update INSTALLATION INSTRUCTIONS NOTE: Items (5, 8, 9 & 10) are pre-assembled WARNING! DISCONNECT BATTERIES BEFORE SERVICING. DRAIN THE SOLUTION SYSTEM PRIOR TO INSTALLATION. 1 See Figure 1. Install the Washers (6), Step Bushings (3) and Screws (4) on the back of the recovery tank as shown. Hang the Caddy Assembly (pre-assembled items 5, 8, 9, 10) on the Step Bushings (3). 2 Install the Wand Assembly (7), Hose Assembly (1) and Coupler (2) onto the Caddy as shown. page 1 of 14
FIGURE 1 Rear View 1 4 3 6 1 5 8 9 10 7 Wand Assembly can be temporarily stored fully assembled by clipping into the two clamps shown for quickly moving from site to site without disassembling and re-assembling each time. 2 page 2 of 14
INSTALLATION INSTRUCTIONS FOR Advenger / BR600S & Adgressor / BR850S models BUILT PRIOR TO: (see serial# chart ) 3 See Figure 2. Remove Hose (AA) and Hose (BB) from the pump. Ensure that the elbows on the pump are oriented as shown (rotate if necessary). NOTE: Use pipe sealant on elbows. 4 Remove Tee (CC) from Hose (AA) and connect Hose (AA) to the elbow that you removed Hose (BB) from. 5 Cut Hose (BB) to a length of 2 (5cm) and install on the other elbow as shown. 6 Install Tee (CC) in the end of Hose (BB) as shown. SERIAL NUMBER CHART 1837726-Advenger 2400D 1839732-Advenger 2400C 1839732-Advenger 2600D 1839732-Advenger 2600C 1837203-Advenger 2810D 1837599-Advenger 3210D 1837200-Advenger 2810C 1837197-Advenger 3210C 1837616-BR600S 1837623-BR700S 1839156-BR800S 1837650-BR600SC 1837652-BR700SC 1839732-BR800SC 1837646-Lowes Advenger 3210D 1863250-BR850S series 1863260-Adgressor FIGURE 2 page 3 of 14
7 See Figure 3. Cut Solution Hose (A) 9.50 (24.13cm) downstream from the Solution Filter (B). NOTE: On models with the metered solution valve measure from end of valve closest to the Solution Filter (B). FIGURE 3 This valve is on all Adgressor & BR850S series models but only on Advenger & BR600S series models built after the serial numbers shown in the chart. B SERIAL NUM BER CHART 1750239 - Advenger 2400D 1757986 - Advenger 2810D 1757999 - Advenger 3210D 1759162 - Advenger 2400C 1750252 - Advenger 2600C 1758000 - Advenger 2810C 1758002 - Advenger 3210C 1752024 - BR 600S 1752041 - BR 700S 1752046 - BR 800S 1752052 - BR 600SC 1752054 - BR 700SC 1753522 - BR 800SC A Cut Hose (A) 9.5 inches (24.13cm) downstream from Solution Filter (B). Refer to the illustration on page 10 for a fully assembled view of all components page 4 of 14
8 See Figure 4. Mount Pump Assembly (11) as shown using the two Screws and Washers (C) supplied with the Pump Assembly. NOTE: No drilling required, mounting holes already exist. It may be necessary to cut factory installed Cable Ties from the wiring harness to facilitate pump installation. The pump wiring connects to the existing plug with WHT/BRN and BLK wires feeding it, remove the weather pack seal from plug fi rst. NOTE: Adgressor & BR850S series models require the installation of a mounting plate as shown. 9 Install Grommets (E) from the Pump Assembly (11) as shown and then route Hose (AA) as shown. 10 Install Bulk Head Adapter (G), Barb (H), Nipple (I) and Plug (J) from the Pump Assembly (11) as shown. 11 Connect Hose (AA) to Barb (H) (1) Hose Clamp (D) from the Pump Assembly as shown. 12 Install Cable Ties supplied with Pump Assembly (11) as needed to secure all wiring and hoses. FIGURE 4 These items are included in Pump Assembly 56314309 but only used on Adgressor & BR850S series models. C Underside of Chassis D H G I J 11 Mount Pump (11) directly to chassis as shown for Advenger & BR600S series models. Install Plate as shown and then mount Pump (11) to plate for Adgressor & BR850S series models. AA Connect to machine wiring harness connector with WHT/BRN & BLK wires. E Refer to the illustration on page 10 for a fully assembled view of all components page 5 of 14
13 See Figure 5. Connect one half of Hose (A) to each side of the Tee (CC) on the Pump Assembly and secure with (2) of the Hose Clamps (D) provided with the Pump Assembly. 14 See Operating Instructions. SERIAL NUM BER CHART 1750239 - Advenger 2400D 1757986 - Advenger 2810D 1757999 - Advenger 3210D 1759162 - Advenger 2400C 1750252 - Advenger 2600C 1758000 - Advenger 2810C 1758002 - Advenger 3210C 1752024 - BR 600S 1752041 - BR 700S 1752046 - BR 800S 1752052 - BR 600SC 1752054 - BR 700SC 1753522 - BR 800SC FIGURE 5 D A A D CC This valve is on all Adgressor & BR850S series models but only on Advenger & BR600S series models built after the serial numbers shown in the chart. Refer to the illustration on page 10 for a fully assembled view of all components page 6 of 14
INSTALLATION INSTRUCTIONS FOR ALL AquaRide SE-AXP / BRX700 X, ALL Adhancer SERIAL NUMBER CHART ALL Advenger AXP / BR600S X, Adgressor AXP / BR850S X models 1837725-Advenger 2400D ONLY Advenger / BR600S & Adgressor / BR850S models BUILT AFTER: (see serial# chart ) 1839731-Advenger 2400C 1839731-Advenger 2600D 3 See Figure 6. Mount Pump Assembly (11) as shown using the Plate (DD), Screws (EE) and Screws and 1839731-Advenger 2600C Nuts (FF). 1837202-Advenger 2810D NOTE: No drilling required, mounting holes already exist. On early machines you may have to drill (2).166 1837598-Advenger 3210D (4.21mm) holes as shown. 1837199-Advenger 2810C Plug the pump into the existing wiring connector under the rear of the machine. 1837198-Advenger 3210C NOTE: It may be necessary to cut factory installed Cable Ties from wiring harness to facilitate pump 1837615-BR600S installation. The pump wiring connects to the plug with WHT/BRN and BLK wires feeding it, remove the 1837622-BR700S weather pack seal from plug fi rst. 1839155-BR800S Before proceeding, remove the elbows from the pump, apply pipe sealant to the threads and reinstall. 1837649-BR600SC 1837651-BR700SC 4 Install Grommets (E) from the Pump Assembly (11) as shown and then route Hose (AA) as shown. 1839731-BR800SC 5 Install Bulk Head Adapter (G), Barb (H), Nipple (I) and Plug (J) from the Pump Assembly (11) as shown. 1837645-Lowes Advenger 3210D 6 Route and connect Hose (BB) to Barb (H) using (1) Hose Clamp (D) from the Pump Assembly as shown. 1863249-BR850S series 7 Install Cable Ties supplied with Pump Assembly (11) as needed to secure all wiring and hoses. 1863259-Adgressor Proceed to page 8 for AquaRide SE-AXP / BRX700 X / Advenger AXP / BR600S X, Adgressor AXP / BR850S X, Adhancer models Skip to page 9 for Advenger / BR600S & Adgressor / BR850S models BUILT AFTER: (see serial# chart) FIGURE 6 2" (5.08cm) 10.13" (25.73cm) FF EE.75" (19.05mm) 2 x.166" (4.21mm) 11 DD FF D H G Bottom View of Left Rear corner of chassis Underside of Chassis I J EE 11 Connect to machine wiring harness connector with WHT/BRN & BLK wires AA E BB Refer to the illustration on page 11 for a fully assembled view of all components on AXP / EDS models Refer to the illustration on page 12 for a fully assembled view of all components on standard models page 7 of 14
CONTINUATION OF INSTALLATION INSTRUCTIONS FOR ALL AquaRide SE-AXP / BRX700 X Advenger AXP / BR600S X, Adgressor AXP / BR850S X, Adhancer models 8 See Figure 7. Disconnect Hose (A) from the pump. 9 Install the Hose (GG) as shown and connect Tee (CC) between Hose (GG) and Hose (A) as shown. 10 See Operating Instructions. FIGURE 7 GG CC A Refer to the illustration on page 11 for a fully assembled view of all components page 8 of 14
CONTINUATION OF INSTALLATION INSTRUCTIONS FOR Advenger / BR600S & Adgressor / BR850S models BUILT AFTER: (see serial# chart ) 8 See Figure 7. Cut Solution Hose (A) 9.50 (24.13cm) downstream from the Solution Filter (B). Measure from end of valve closest to the Solution Filter (B). Connect one half of Hose (A) to each side of the Tee (CC) on Hose (AA) and secure with (2) of the Hose Clamps (D) provided with the Pump Assembly. 9 See Operating Instructions. FIGURE 7 B SERIAL NUMBER CHART 1837725-Advenger 2400D 1839731-Advenger 2400C 1839731-Advenger 2600D 1839731-Advenger 2600C 1837202-Advenger 2810D 1837598-Advenger 3210D 1837199-Advenger 2810C 1837198-Advenger 3210C 1837615-BR600S 1837622-BR700S 1839155-BR800S 1837649-BR600SC 1837651-BR700SC 1839731-BR800SC 1837645-Lowes Advenger 3210D 1863249-BR850S series 1863259-Adgressor A Cut Hose (A) 9.5 inches (24.13cm) downstream from Solution Filter (B). AA D A D A CC Refer to the illustration on page 12 for a fully assembled view of all components page 9 of 14
SERIAL NUMBER CHART 1837726-Advenger 2400D 1839732-Advenger 2400C 1839732-Advenger 2600D 1839732-Advenger 2600C 1837203-Advenger 2810D 1837599-Advenger 3210D 1837200-Advenger 2810C 1837197-Advenger 3210C 1837616-BR600S 1837623-BR700S 1839156-BR800S 1837650-BR600SC 1837652-BR700SC 1839732-BR800SC 1837646-Lowes Advenger 3210D 1863250-BR850S series 1863260-Adgressor page 10 of 14
Fully assembled on AXP / EDS models Items shown in black are new components from kit Items shown in grey are pre-existing components on machine TOP VIEW page 11 of 14
SERIAL NUMBER CHART 1837725-Advenger 2400D 1839731-Advenger 2400C 1839731-Advenger 2600D 1839731-Advenger 2600C 1837202-Advenger 2810D 1837598-Advenger 3210D 1837199-Advenger 2810C 1837198-Advenger 3210C 1837615-BR600S 1837622-BR700S 1839155-BR800S 1837649-BR600SC 1837651-BR700SC 1839731-BR800SC 1837645-Lowes Advenger 3210D 1863249-BR850S series 1863259-Adgressor page 12 of 14
Operating Instructions: 1 Assemble Wand Assembly (7) and connect one end of Hose Assembly (1) to the Wand Assembly (7). Connect the Quick Disconnect (HH) to the Wand Assembly (7). 2 Disconnect the Hose (II) from the squeegee and insert Coupler (2) into the end, connect the other end of Hose Assembly (1) to the Coupler (2). Connect the Quick Disconnect (JJ) from Hose Assembly (1) to Plug (J) under the left rear corner of the machine. 3 Re-connect the batteries, fi ll the solution tank at least half full, turn the Key Switch (KK) ON, open Solution Valve (LL) 1/2 to full (non AXP scrubbers only) and push the Wand Kit Button (MM) on the touch pad control panel to turn ON the Vacuum and Pump System. Squeeze trigger on wand to purge air from system. page 13 of 14
page 14 of 14