GRUNDFOS DATA BOOKLET TP 1-6/4-A-F-A-BUBE 4Y 5HZ Grundfos Pump 9642628 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9642628/tp-1-6-4-a-f-a-bube.html info@lenntech.com tel. +31-15-261.9. fax. +31-15-261.62.89 BE > THINK > INNOVATE
Position Qty. Description 1 TP 1-6/4 A-F-A-BUBE Product No.: 9642628 Single-stage, close-coupled, volute pump with in-line suction and discharge ports of identical diameter. The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is fitted with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. Pipework connection is via PN 1 DIN flanges (EN 192-2 and ISO 75-2). The pump is fitted with a fan-cooled asynchronous motor. Further product details The product's minimum efficiency index (MEI) is greater or equal to.7. This is by the Commission Regulation (EU) considered as an indicative benchmark for best-performing water pump available on the market as from 1 January 213. Pump Pump housing and pump head are electrocoated to improve the corrosion resistance. Electrocoating includes: 1) Alkaline-based cleaning. 2) Pretreatment with zinc phosphate coating. 3) Cathodic electrocoating (epoxy). 4) Curing of paint film at 2-25 C. 1: Pump housing 2: Impeller 3: Shaft 4: Coupling 5: Pump head The pump housing is provided with a replaceable stainles steel/ptfe neck ring to reduce the amount of liquid running from the discharge side of the impeller to the suction side. The impeller is secured with a split cone with nut. The pump is fitted with an unbalanced rubber bellows seal with torque transmission across the spring and around the bellows. Due to the bellows, the seal does not wear the shaft, and the axial movement is not prevented by deposits on the shaft. Primary seal: - Rotating seal ring material: Tungsten carbide (WC) - Stationary seat material: Carbon graphite, resin-impregnated This is a widely used material pairing. If the pumped liquid contains particles, wear on the seal faces must be expected. Due to the favourable lubricating properties of carbon graphite, the seal is suitable for use even under poor lubricating conditions, such as hot water. However, under such conditions, wear on the carbon graphite face reduces seal life. Secondary seal material: EPDM (ethylene-propylene rubber) EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils.
Position Qty. Description A circulation of liquid through the duct of the air vent screw ensures lubrication and cooling of the shaft seal. The flanges have tappings for mounting of pressure gauges. The motor stool forms connection between the pump housing and the motor, and is equipped with a manual air vent screw for venting of the pump housing and the shaft seal chamber. The sealing between motor stool and pump housing is an O-ring. The central part of the motor stool is provided with guards for protection against the shaft and coupling. Motor and pump shaft are connected via a rigid two-part coupling. Motor The motor is a totally enclosed, fan-cooled motor with principal dimensions to IEC and DIN standards. Electrical tolerances comply with IEC 634. The motor is flange-mounted with tapped-hole flange (FT). Motor mounting designation in accordance with IEC 634-7: IM B 14, IM V 18 (Code I) / IM 361, IM 3611 (Code II). The motor efficiency is classified as IE3 in accordance with IEC 634-3. The motor can be connected to a variable speed drive for adjustment of pump performance to any duty point. Grundfos CUE offers a range of variable speed drives. Please find more information in Grundfos Product Center. Technical data Liquid: Pumped liquid: Water Liquid temperature range:.. 14 C Liquid temperature during operation: 2 C Density: 998.2 kg/m³ Technical: Speed for pump data: Rated flow: Rated head: Actual impeller diameter: Primary shaft seal: Curve tolerance: Materials: Pump housing: Impeller: 143 rpm 63 m³/h 5.4 m 144 mm BUBE ISO996:212 3B Cast iron EN-JL14 ASTM A48-4 B Stainless steel DIN W.-Nr. 1.431 AISI 34 Installation: Range of ambient temperature: -3.. 6 C Maximum operating pressure: 1 bar Flange standard: DIN Pipe connection: DN 1 Pump inlet: DN 1 Pump outlet: DN 1 Pressure rating: PN 1 Port-to-port length: 45 mm Flange size for motor: FT115 Electrical data: Motor type: IE Efficiency class: Rated power - P2: Power (P2) required by pump: Mains frequency: Rated voltage: 9SB IE3 1.1 kw 1.1 kw 5 Hz 3 x 22-24D/38-415Y V
Position Qty. Description Rated current: 4,85/2,8 A Starting current: 82-9 % Cos phi - power factor:,71-,64 Rated speed: 145-146 rpm Efficiency: IE3 84,1% Motor efficiency at full load: 84.1 % Motor efficiency at 3/4 load: 84.6 % Motor efficiency at 1/2 load: 82.9 % Number of poles: 4 Enclosure class (IEC 34-5): 55 Dust/Jetting Insulation class (IEC 85): F Others: Minimum efficiency index, MEI :.7 ErP status: EuP Standalone/Prod. Net weight: 61.8 kg Gross weight: 67.7 kg Shipping volume:.16 m³
9642628 TP 1-6/4 5 Hz H [m] TP 1-6/4, 3*4 V, 5Hz eta [%] 7.5 7. 6.5 6. 5.5 5. 1 4.5 9 4. 8 3.5 7 3. 6 2.5 5 2. 4 1.5 3 1. 2.5 1. 5 1 15 2 25 3 35 4 45 5 55 6 65 7 75 P [W] 16 Q [m³/h] 8 NPSH [m] 14 P1 7 12 1 P2 6 5 8 4 6 3 4 2 2 1
RP 1/4 M16 225 173 121 1 45 11 178 173 Description Value General information: Product name: TP 1-6/4 A-F-A-BUBE Product No: 9642628 EAN number: 5739675691 Technical: Speed for pump data: 143 rpm Rated flow: 63 m³/h Rated head: 5.4 m Head max: 6 dm Actual impeller diameter: 144 mm Primary shaft seal: BUBE Curve tolerance: ISO996:212 3B Pump version: A Model: A Materials: Pump housing: Cast iron EN-JL14 ASTM A48-4 B Impeller: Stainless steel DIN W.-Nr. 1.431 AISI 34 Material code: A Installation: Range of ambient temperature: -3.. 6 C Maximum operating pressure: 1 bar Flange standard: DIN Connect code: F Pipe connection: DN 1 Pump inlet: DN 1 Pump outlet: DN 1 Pressure rating: PN 1 Port-to-port length: 45 mm Flange size for motor: FT115 Liquid: Pumped liquid: Water Liquid temperature range:.. 14 C Liquid temperature during operation: 2 C Density: 998.2 kg/m³ Electrical data: Motor type: 9SB IE Efficiency class: IE3 Rated power - P2: 1.1 kw Power (P2) required by pump: 1.1 kw Mains frequency: 5 Hz Rated voltage: 3 x 22-24D/38-415Y V Rated current: 4,85/2,8 A Starting current: 82-9 % Cos phi - power factor:,71-,64 Rated speed: 145-146 rpm Efficiency: IE3 84,1% Motor efficiency at full load: 84.1 % Motor efficiency at 3/4 load: 84.6 % Motor efficiency at 1/2 load: 82.9 % Number of poles: 4 Enclosure class (IEC 34-5): 55 Dust/Jetting Insulation class (IEC 85): F Motor protec: PTO Motor No: 86U595 Others: Minimum efficiency index, MEI :.7 ErP status: EuP Standalone/Prod. Net weight: 61.8 kg Gross weight: 67.7 kg Shipping volume:.16 m³ H [m] 7.5 7. 6.5 6. 5.5 5. 4.5 4. 3.5 3. 2.5 2. 1.5 1..5 TP 1-6/4, 3*4 V, 5Hz. 1 2 3 4 5 6 7 Q [m³/h] P [W] 14 12 1 8 6 4 2 173 11 1 173 121 173 L1 625 L2 122 182 LOW VOLTAGE DIRECTION OF ROTATION HIGH VOLTAGE DIRECTION OF ROTATION L1 L2 L3 M16 L3 178 45 225 RP 1/4 2 P1 P2 9 8 7 6 5 4 3 2 1 eta [%] 1 7 6 5 4 3 2 1 NPSH [m]
Description Sales region: Value GB
9642628 TP 1-6/4 5 Hz cos phi eta TP1-6/4 + 9SB 1.1 kw 3*4 V, 5 Hz I [A].8 eta cos phi 4. I.6 3..4 2..2 1...1.2.3.4.5.6.7.8.9 1. 1.1 1.2 1.3 1.4 n [rpm] P2 [kw] P1. P1 [kw] 16 1.6 15 1.2 n 14.8 13.4 12.
9642628 TP 1-6/4 5 Hz 173 11 173 178 625 RP 1/4 122 182 1 173 121 45 2 M16 225 Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details.
9642628 TP 1-6/4 5 Hz LOW VOLTAGE DIRECTION OF ROTATION L1 L2 L3 HIGH VOLTAGE DIRECTION OF ROTATION L1 L2 L3 Note! All units are in [mm] unless others are stated.
Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice. Please contact us to verify the data above is still accurate/up-to-date. All information is copyright Grundfos. info@lenntech.com www.lenntech.com tel. +31-15-261.9. fax. +31-15-261.62.89