Instruction Sheet P/N 1093-04 Inverted Dual High Pressure Fluid Filter Assemblies Introduction WARNG: High pressure fluids are hazardous. To prevent serious injury when installing and servicing filters, shut off the fluid pump and relieve the fluid pressure before disconnecting any fittings or hoses. See Figure 1. The Nordson dual-filter assemblies are designed for constant demand applications where it is impractical to stop production for filter cleaning or servicing. Each filter assembly is shipped with 0.00 in. reinforced screens. (For CleanSpray systems, install 0.00 in. screens). Refer to the Inverted High Pressure Fluid Filter instruction sheet part 33190 for filter repair and parts information. Standard Inverted Dual Filters with Three-Way Ball Valves Narrow Inverted Dual Filters with Three-Way Ball Valves Inverted Dual Filters with Check Valves Figure 1 Inverted Dual High-Pressure Fluid Filter Assemblies Specifications Standard Inverted Dual Filters with Three-Way Ball Valves Narrow Inverted Dual Filters with Three-Way Ball Valves Inverted Dual Filters with Check Valves Overall Height 44. mm (1.7 in.) 44. mm (1.7 in.) 355. mm (14 in.) Mounting Plate Length 177.8 mm (7 in.) 177.8 mm (7 in.) 38.3 mm (14.5 in.) Mounting Plate Width 101. mm (4 in.) 101. mm (4 in.) 7. mm (3 in.) Input/Output Fittings 1 / 0 JIC 1 / 0 JIC 1 / 0 JIC Maximum Operating Pressure 07 bar (3000 psi) 07 bar (3000 psi) 07 bar (3000 psi)
Inverted Dual High Pressure Fluid Filter Assemblies Mounting Mount the filter assembly in the downward position as illustrated in Figure 1. NOTE: Torque filter bowl to 15 0 ft-lbs. Do not over-tighten. Connect input and output fluid hoses to the and 1 / -0 JIC fittings as shown in Figures, 3, and 4. NOTE: Flush the filter with solvent prior to the first use. Failure to do so could result in paint contamination. Valve Handle Positions Standard Inverted Dual Filters with Three-Way Ball Valve See Figure for handle positions. Left filter in use Drain and service right filter Right filter in use Drain and service left filter Figure Handle Positions Inverted Dual Filter Assembly with Three-Way Ball Valve Standard
Inverted Dual High Pressure Fluid Filter Assemblies 3 Narrow Inverted Dual Filters with Three-Way Ball Valve Left filter in use Drain and service right filter Right filter in use Drain and service left filter Figure 3 Handle Positions Inverted Dual Filter Assembly with Three-Way Ball Valve Narrow Inverted Dual Filters with Check Valves Left filter in use Drain and service right filter Figure 4 Right filter in use Handle Positions Inverted Dual Filter Assembly with Check Valves Drain and service left filter
4 Inverted Dual High Pressure Fluid Filter Assemblies Parts To order parts, call the Nordson Finishing Customer Support Center at (800) 433 9319 or your local Nordson representative. Standard Inverted Dual-Filter with Three-Way Ball Valve See Figure 5. Item Part Description Quantity Note 338431 FILTER, dual, three-way valve, stainless 1 1 750130 VALVE, ball, stainless 973059 NIPPLE, hex, 3 / 8 x 3 / 8 x 1.45 in., stainless 4 B 3 337717 HOUSG, filter, stainless 4 1110 SCREEN, reinforced, 0.00 in. 4 C, D 5 338184 SPRG, compression, 4.50 x 0.855 x 0.1 in. 97718 ELBOW, male, 37, 1 / 0 x 3 / 8 in. NPT B 7 4773 VALVE, ball, three-way, stainless 8 338435 TUBG, outlet, dual-filter, stainless 1 9 971451 ELBOW, male, hydraulic, compression, 1 / in. tube x 3 / 8 in. NPT B 10 973180 ELBOW, pipe, hydraulic, 90, 3 / 8 in., stainless 1 B 11 338433 TUBG, inlet, dual-filter, stainless 1 1 97343 PLUG, pipe, socket, standard, 3 / 8 in., stainless 13 33847 BRACKET, standoff, filter 14 1137 PLATE, mounting 1 15 983051 WASHER, flat, 0.344 x 0.88 x 0.05 in., zinc 8 1 983150 LOCK WASHER, split, 5 / 1 in.,, nickel 8 17 981333 SCREW, hex, 5 / 1 18 x 0.875 in., cap, zinc 4 18 984140 NUT, hex, regular, 5 / 1 18,, zinc 4 19 338844 SCREW, socket, 5 / 1 18 x 3 in., black 4 0 338178 BASE filter, stainless, right-hand 1 94030 O-RG, PTFE, 1.5 x 1.75 x 0.0 in. A 97151 CONNECTOR, male, elbow, 0.50 tube x 0.38 in. NPT, stainless B NS 1151 LUBRICANT, O-ring, Parker, oz AR A NS 900481 ADHESIVE, pipe/thread/hydraulic sealant AR B NOTE A: Apply O-ring grease before assembly. B: Apply pipe/thread/hydraulic sealant adhesive before assembly. C: Two screens are installed in the filters, and two are shipped with the assembly as spares. D: CleanSpray systems require 0.00 in. screen 1110. Refer to page 8 for optional screen sizes. AR: As Required NS: Not Shown
Inverted Dual High Pressure Fluid Filter Assemblies 5 13 13 Top View 10 9 9 11 7 8 Front View 0 7 15 1 18 19 13 14 Side View NORDSON CORPORATION AMHERST, OHIO 44001 USA MODEL MAXIMUM OPERATG PRESSURE SERIAL PART NO. NO. PSI BAR 5 4 1 1 15 1 17 3 1 Figure 5 Standard Inverted Dual-Filters with Three-Way Ball Valves
Inverted Dual High Pressure Fluid Filter Assemblies Narrow Inverted Dual-Filter with Three-Way Ball Valve See Figure. Item Part Description Quantity Note FILTER, dual, three-way valve, stainless, 109319 1 narrow 1 750130 VALVE, ball, stainless 973059 NIPPLE, hex, 3 / 8 x 3 / 8 x 1.45 in., stainless 4 A 3 337717 HOUSG, filter, stainless 4 1110 SCREEN, reinforced, 0.00 in. C, D 5 338184 SPRG, compression, 4.50 x 0.855 x 0.1 in. 97718 ELBOW, male, 37, 1 / 0 x 3 / 8 in. NPT 7 4773 VALVE, ball, three-way, stainless 8 338178 BASE filter, stainless, right-hand PLUG, pipe, socket, standard, 9 97343 3 / 8 in., stainless A 10 94030 O-RG, PTFE, 1.5 x 1.75 x 0.0 in. B 11 TUBG, inlet/outlet, dual-filter, stainless 1 97151 CONNECTOR, male, elbow, 0.50 tube x 0.38 in. NPT, stainless 4 A ELBOW, pipe, hydraulic, 90, 13 973180 3 / 8 in., stainless A 14 98191 SCREW, drive, round, x 0.15 in., zinc 15 983051 WASHER, flat, 0.344 x 0.88 x 0.05 in., zinc 8 1 983150 LOCK WASHER, split, 5 / 1 in.,, nickel 8 17 984140 NUT, hex, regular, 5 / 1 18,, zinc 4 18 338844 SCREW, socket, 5 / 1 18 x 3 in., black 4 19 1137 PLATE, mounting 1 0 981340 SCREW, socket, 5 / 1 18 x 0.750 in., black 4 1 1107710 BRACKET, standoff, filter 90075 CAP PLUG, tapered, 0.547 in. O.D. NS 1151 LUBRICANT, O-ring, Parker, oz AR B NS 900481 ADHESIVE, pipe/thread/hydraulic sealant AR A NS TAPE, pipe thread AR A NOTE A: Apply pipe/thread/hydraulic sealant adhesive before assembly. B: Apply O-ring grease before assembly. C: Two screens are installed in the filters, and two are shipped with the assembly as spares. D: CleanSpray systems require 0.00 in. screen 1110. Refer to page 8 for optional screen sizes. AR: As Required NS: Not Shown
Inverted Dual High Pressure Fluid Filter Assemblies 7 1 Top View 13 Side View 15 1 17 18 13 14 19 1 11 1 7 1 15 1 0 Front View 7 7 5 4 ÇÏÏ Ç ÏÏÏ Ì ÎÎ ÎÇ ÏÌ ÇÏÏ ÎÎ ÏÇ Ï ÇÏÏ ÎÎ ÏÇ Ï ÇÏÏ ÎÎ ÏÇ Ï ÇÏÏ ÎÎ ÏÇ Ï 8 9 3 10 1 Figure Narrow Inverted Dual-Filters with Three-Way Ball Valves
8 Inverted Dual High Pressure Fluid Filter Assemblies Inverted Dual-Filter with Check Valve See Figure 7. Item Part Description Quantity Note 33844 FILTER, dual, check valve, stainless 1 1 941140 O-RG, hot paint, 0.5 x 0.813 x 0.094 in. 1 A 193 BLOCK, adapter, 3 / 8 in. NPT 1 3 97718 ELBOW, male, 37, 1 / 0 x 3 / 8 in. NPT B 4 1931 VALVE, check, stainless, 3 / 8 in. NPT B 5 18543 ADAPTER, 3 / 8 in. NPT 1 750130 VALVE, ball, stainless 4 7 973059 NIPPLE, hex, 3 / 8 x 3 / 8 x 1.45 in., stainless B 8 337717 HOUSG, filter, stainless 9 9734 ELBOW, male, pipe, hydraulic, 3 / 8 in., stainless B 10 33849 BASE, filter, stainless, left-hand 1 11 9710 CONNECTOR, male, 0.50 tube x 3 / 8 in. NPT, 1 B stainless 1 - - - - - - TUBE, 304 stainless, 0.50 x 0.049 in., 1 0.40 ft 13 1094837 TEE, male run,, 0.50 tube x 3 / 8 in. NPT x 0.50 1 tube, stainless 14 973415 PLUG, pipe, socket, standard, 1 / 4 in., stainless 1 15 109483 ADAPTER, female, 0.50 in. tube x 3 / 8 in. NPT, 1 B stainless 1 338178 BASE, filter, stainless, right-hand 1 17 94030 O-RG, PTFE, 1.5 x 1.75 x 0.0 in. A 18 1110 SCREEN, reinforced, 0.00 in. 4 C, D 19 338184 SPRG, compression, 4.50 x 0.855 x 0.1 in. 0 983051 WASHER, flat, 0.344 x 0.88 x 0.5 in., zinc 8 1 983150 LOCK WASHER, split, 5 / 1 in.,, nickel 8 98138 SCREW, hex, 5 / 1 18 x 0.5 in., cap, zinc 4 3 984140 NUT, hex, regular, 5 / 1 18,, zinc 4 4 338844 SCREW, socket, 5 / 1 18 x 3 in., black 4 5 1933 PLATE, mounting 1 33847 BRACKET, standoff, filter 7 97343 PLUG, pipe, socket, standard, 3 / 8 in., stainless NS 1151 LUBRICANT, O-ring, Parker, oz AR A NS 900481 ADHESIVE, pipe/thread/hydraulic sealant AR B NOTE A: Apply O-ring lubricant before assembly. B: Apply pipe/thread/hydraulic sealant adhesive before assembly. C: Two screens are installed in the filters, and two are shipped with the assembly as spares. D: CleanSpray systems require 0.00 in. screen 1110. Refer to page 8 for optional screen sizes. AR: As Required NS: Not Shown
Inverted Dual High Pressure Fluid Filter Assemblies 9 Top View 14 7 10 9 13 1 11 1 0 1 3 4 Side View 0 1 9 15 3 Front View 5 8 8 7 7 17 19 18 5 4 1 4 Figure 7 Bottom View Inverted Dual-Filters with Check Valves
10 Inverted Dual High Pressure Fluid Filter Assemblies Optional Screens Part 1100 SCREEN, 0.00 in., not reinforced 11030 SCREEN, 0.030 in., not reinforced 1110 SCREEN, 0.00 in., reinforced 11344 SCREEN, 0.00 in., assembly 11103 SCREEN, 0.003 in., reinforced 11104 SCREEN, 0.004 in., reinforced 1110 SCREEN, 0.00 in., reinforced 11109 SCREEN, 0.009 in., reinforced 1111 SCREEN, 0.01 in., reinforced 11115 SCREEN, 0.015 in., reinforced 1110 SCREEN, 0.00 in., reinforced Description Optional 0.00 Screen Assembly with Adapter Use this screen assembly with low flow rate nozzles (below 0.015 gpm). Item Part Description Quantity Note 11344 SCREEN, 0.00 in., assembly 1 1 11339 ADAPTER assembly, screen 94010 O-RG, PTFE, 0.9385 x 1.03 x 0.03 in. 1 3 11349 ADAPTER, screen 1 4 111 SCREEN, reinforced, 0.00 in. 1 3 4 3 1 1 Figure 8 Optional 0.00 Screen Assembly with Adapter Issued 3/18 Original copyright date 000. Nordson and the Nordson logo are registered trademarks of Nordson Corporation.