STANDARD CONSTRUCTION FEATURES Page 141.1 SERIES 15 Pumps Cutaway View (Packed Type) 8-15-0 GPM Sizes (--7 m³/hr) MECHANICAL SEAL (SERIES 415) G - HL, K - LL SIZES AK, AL, LS - M SIZES BRACKET 5 416 SHAFT ROTOR 1 Bellows O-Ring Rotating Face 4 Stationary Seat 5 Metal Retainer 6 Spring REVOLVABLE PUMP CASING (Standard Equipment) All Series 15 and 415 pumps are equipped with pump casings that can be turned to eight positions except the LQ, LL, and QS sizes. These can be turned in all positions except for a port in the 6 o clock position. Relief valve must point to suction port in all cases. FEATURES 1 Bellows O-Ring Rotating Face 4 Stationary Seat 5 Metal Retainer 6 Spring SERIES 415 Cutaway View (Mechanical Seal Type) 50-75-100-15 GPM Sizes (11-17--1 m³/hr) SERIES 15 Pumps Note: 50 and 75 GPM sizes have seal located in stuffing box area. Cutaway View (Packed Type) 140-00-00-40-500 GPM Sizes (-45-68-95-114 m³/hr) Note: 500 GPM ( QS size) has opposite ports as standard. BRACKET 5 984167 SHAFT 7 Set Collar 8 Seal Holder 9 Seal Plate OVERPRESSURE RELIEF VALVE (Standard Equipment) Valve permits bypassing of liquids and prevents excessive pressures in the discharge line. If reversing pump, remove valve and turn end for end. Relief valve must point to suction port in all cases. All valves set at 50 lbs. unless otherwise requested. If overpressure relief valve is not used, pumping system should include some form of overpressure protection, e.g., relief valve in dis charge line, torque limiting devices, rupture discs, etc. POSITIVE-LOCK THRUST CONTROL Series 15 and 415 pumps are manufactured with positive-lock thrust control for accurate axial positioning of rotor and shaft. Illustration shows bearing and double end cap arrangement. 1 Pressure Range 1 Temperature Range 1 Viscosity Range GPM 8-15-0-50-75-100- 15-140-00-00-40-500 (m³/hr --7-11-17--1--45-68-95-114) (Nominal Rating) It is the unique and unusually simple construction that has made our rotary pumps so adaptable to so many diversi fied installations. They possess excellent vacuum develop ing characteristics and operate equally well in either direction. Because of the cushioned action in providing a continuous and steady stream of liquid without foaming or churning, it is adaptable to an unlimited number of indus trial applications. The rugged construction of these heavy-duty pumps assures long life and peak, trouble-free operation on nor mal-duty installation and outstanding performance when handling liquids at greater pressures. These heavy-duty pumps are furnished as standard with packed-type or mechanical seal construction for shaft pro tection and prevention of leakage. Packed pumps provide extra-deep stuffing box. The rotarytype mechanical seal works with, rather than against, pressure. It is self-adjust ing and seals without leakage. Because of its method of seal ing it prevents scoring of the pump drive shaft. The Series 415 mechanical seal pumps can handle liq uids with viscosities up to 15,000 SSU. Special seals for higher viscosities are available; consult factory. 1 Values shown represent minimums or maximums. Some special construc tion or consideration may be required before a cataloged pump can be applied to an application involving maximum pressure or minimum or maximum temperature and/ or viscosity. Certain models have restrictions in pres sure and/or viscosities. See specifications, page 141., and performance curves, which can be electronically generated with the Viking Pump Selector Program, located on www.vikingpump.com. Nominal capacities based on handling thin liquids at low pressures. Metric conversions are based on US measurements and rounded to the nearest whole number. 00 PSI (14 BAR) for 100 SSU (1 cst) and above 100 PSI (7 BAR) for below 100 SSU (1 cst) -60 F. to +650 F. (-51 C. to +4 C.) 8 SSU to,000,000 SSU (0.1 cp to 440,000 cst)
Page 141. VIKING HEAVY DUTY PUMPS UNMOUNTED PUMPS G, H, and HL Sizes AK and AL Sizes LS Size Q and M Sizes K, KK, and L Sizes LQ and LL Sizes This series of heavy-duty pumps is available either unmounted or mounted as shown on following pages. Available with packed stuffing box or Buna-N mechanical seal with carbon rotating and Ni-Resist stationary faces. The integral thrust bearing is designed to handle heavyduty pumping jobs without problems of end play and distor tion. For increased versatility of installation and complete selection of ports, many of the pump casings are designed so they can be rotated on the bracket to any CONSTRUCTION SERIES 15 and 1 415 ( G THROUGH M SIZES) Bushings Pump Rotor Shaft And Packed Mechanical Seal Construction Casing Head Bracket Rotor Idler Idler Pin Idler Bracket Idler Bracket Standard Carbon Iron Iron Iron 7 Iron 1 Iron Steel Bronze Bronze Construction Graphite 10 Bronze 11 Steel Carbon Iron Iron Iron Steel Iron Steel Bronze Bronze Fitted Graphite 10 Bronze 9 Bronze Carbon Iron Iron Iron 9 Bronze Bronze Steel Bronze Bronze Fitted Graphite 10 Bronze SPECIFICATIONS SERIES 15 and 1 415 UNMOUNTED PUMPS QS Size 45 or 90 angle from that shown in the illustrations. See revolvable casing feature on Page 141.1. Overpressure relief valve on head is standard for this series. To permit use of this type pump in a greater range of applications, some sizes are available with jacketed head plate. For heavy-duty pumps with jacketed bracket and head, see Catalog Section 14. Dimensions for Unmounted Pumps See Page 141.8. Internal Pressure Relief Valve Model Numbers Port Size 6 Nominal Pump Rating Maximum Hydrostatic Pressure Steel Fitted Construction Above This Viscosity 8 Maximum Discharge Pressure When Handling 100 SSU Liquid At Nominal Rated Speeds 5 Maximum Temperature for Cataloged Pump F. ( C.) Approximate Shipping Weight With Valve Mech. Packed 110 Mech. Seal Inches GPM (m³/hr) RPM PSIG (BAR) SSU (cst) PSIG Packed Seal Pounds (KG) G15 G415 1 8 () 1800 400 (8) 9 7,500 (1,650) 00 00 (149) 5 (107) (10) H15 H415 1½ 15 () 1800 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 8 (17) HL15 HL415 1½ 0 (7) 1800 400 (8) 7,500 (1,650) 00 00 (149) 5 (107) 40 (18) AK15 AK415 50 (11) 100 400 (8) 11 5,000 (5,500) 150 00 (149) 5 (107) 78 (5) AL15 AL415 75 (17) 100 400 (8) 11 5,000 (5,500) 150 00 (149) 5 (107) 81 (7) K15 K415 75 (17) 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 105 (48) KK15 KK415 100 () 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 110 (500 L15 L415 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 155 (70) LQ15 LQ415 4 ½ 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 175 (79) LL15 LL415 4 140 () 50 400 (8),500 (550) 00 00 (149) 5 (107) 185 (84) LS15 LS415 4 00 (45) 640 400 (8) 75,000 (16,500) 150 00 (149) 5 (107) 190 (86) Q15 Q415 4 4 00 (68) 50 400 (8) 7,500 (1,650) 150 00 (149) 5 (107) 440 (00) QS15 QS415 4 6 500 (114) 50 400 (8) 75,000 (16,500) 150 00 (149) 5 (107) 540 (45) M15 M415 4 4 40 (95) 40 400 (8) 5,000 (5,500) 150 00 (149) 5 (107) 600 (7) 1 Buna-N elastomer used in mechanical seal of Series 415 pumps. Viton, and/or other speeds, see performance curves, which can be electronically Neoprene, and PTFE mechanical seals also available. generated with the Viking Pump Selector Program, located on www.vikingpump. G, Q, and QS sizes have steel idler when steel fitted construction is required. com. Performance curves also show preferred constructions. If suction pressure For mechanical seal pumps on applications with viscosities above 15,000 SSU exceeds 50 PSIG ( BAR), consult factory. (,00 cst), provide details for recommendation. 9 Check factory before using bronze rotors at viscosities normally requiring steelfitted 4 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel com panion construction. G, AK, AL, LS, and QS sizes not available in bronze- flanges or flanged fittings. All others tapped for standard pipe. fitted construction. 5 Standard seal can be used from -0 F. to +5 F. With special construc tion, 10 AK, AL, LS, Q, QS, and M 415 models furnished with carbon graphite temperatures from -60 F. to +650 F. can be handled with this series pumps. bracket bushings and mechanical seal is mounted in stuffing box. Mechanical seal is 6 Nominal rating based on handling thin liquids. mounted behind rotor in G, H, HL, K, KK, L, LQ, and LL pumps. 7 AK, AL, KK, LS, and QS sizes have ductile iron rotor. 11 AK and AL sizes not available in steel-fitted construction. 8 For maximum recommended discharge pressures when handling other vis cosities 1 G, H and HL sizes have powdered metal idler. Metric conversions are based on US measurements and rounded to the nearest whole number. Viton Registered trademark of DuPont Performance Elastomers. Iron Iron Iron
Page 141. VIKING HELICAL GEAR REDUCTION UNITS ( R DRIVE) with R Drive A Reducer QS Size with R Drive C Reducer with R Drive B Reducer with R Drive C Reducer Heavy-duty pump Series 15 and 415 are available with helical gear reducers that have been specifically developed for efficient operation with heavy-duty pumps. These rugged, compact, exceptionally quiet gear reducers come in three sizes: the small A size, medium B size, and large C size and are all bracket mounted requiring flexible cou plings for both input and output shafts. The A size reducer, available with four gear ratios (.4,.76,.4, and 4.17 to 1), is ideally suited for use with the G, H, HL, AK and AL size pumps. With the A size reducer and 100 or 1800 RPM motors, the G, H, HL, AK, and AL size pumps can be used to cover a capacity range to 51 GPM. The medium size B helical gear reducer is available with eight gear ratios from 1.87 to 1 to 7.65 to 1. This size normally is used with pump sizes AK through LS. With the B reducer, AK through LS pumps driven by 100 or 1800 RPM motors can be used to cover a capacity range to 1 GPM. The large C size reducer also is available with seven gear ratios from.1 to 1 to 7.65 to 1. It is normally used with the KK through M size pumps. With the C reducer, KK through M size pumps driven by 100 or 1800 RPM motors can cover a capacity range to 500 GPM. Dimensions for R Drive Units See Pages 141.9 and 141.10.
Page 141.4 VIKING HEAVY DUTY PUMPS VIKING HELICAL GEAR REDUCER UNITS ( R DRIVE) SPECIFICATIONS R DRIVE UNITS Model Numbers Port Size 5 Nominal Pump Rating Maximum Hydro- Static Pressure Steel-Fitted Construction Above This Viscosity OUTSTANDING FEATURES 1. Mounts NEMA standard motors, 100 or 1800 RPM. (5 HP, 1800 RPM maximum with A reducer; 15 HP, 1800 RPM maximum with B reducer; and 50 HP, 1800 RPM maximum with C reducer.). Complete reducers within a size may be interchanged on a pump unit to obtain desired pump speeds and capacities. Thus the four gear ratios within the A size reducer may be interchanged within the size by selecting the proper pinion and gear of a common ratio. Similarly, all eight B reducers are interchangeble on each respective series of B reducer units. All seven C reducers are interchangeable on each respective series of C reducer units.. Quiet operation. High hardness helical gears run in a bath of oil. 4. Compact, narrow and low to fit in small space and low overhead. Maximum Discharge Pressure When Handling 100 SSU Liquid At Nominal Rated Speeds 5. 6. 7. 8. 9. 10. 11. 6 Maximum Temperature For Cataloged Pump F. ( C.) Approximate Shipping Weight With Valve (Less Power) Pounds (KG) Packed 1 Mech. Seal Inches GPM (m³/hr) RPM PSIG (BAR) SSU (cst) PSIG Packed Mech. Seal A Reducer B Reducer C Reducer G15R G415R 1 8 () 1800 400 (8) 7,500 (1,650) 00 00 (149) 5 (107) 109 (49)...... H15R H415R 1½ 15 () 1800 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 15 (57)...... HL15R HL415R 1½ 0 (7) 1800 400 (8) 7,500 (1,650) 00 00 (149) 5 (107) 10 (59)...... AK15R AK415R 50 (11) 100 400 (8) 7 5,000 (5,500) 150 00 (149) 5 (107) 170 (77) 00 (16)... AL15R AL415R 75 (17) 100 400 (8) 7 5,000 (5,500) 150 00 (149) 5 (107) 17 (79) 0 (18)... K15R K415R 75 (17) 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107)... 7 (148)... KK15R KK415R 100 () 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107)... 4 (15) 550 (50) L15R L415R 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107)... 80 (17) 590 (68) LQ15R LQ415R 4 ½ 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107)... 415 (188) 65 (97) LL15R LL415R 4 140 () 50 400 (8),500 (550) 00 00 (149) 5 (107)... 445 (0) 655 (18) LS15R LS415R 4 00 (45) 640 400 (8) 75,000 (16,500) 150 00 (149) 5 (107)... 490 () 700 (454) Q15R Q415R 4 4 00 (68) 50 400 (8) 7,500 (1,650) 150 00 (149) 5 (107)...... 1000 (499) QS15R QS415R 4 6 500 (114) 50 400 (8) 75,000 (16,500) 150 00 (149) 5 (107)...... 1100 (499) M15R M415R 4 4 40 (95) 40 400 (8) 5,000 (5,500) 150 00 (149) 5 (107)...... 1140 (518) 1 Buna-N elastomer used in mechanical seal of Series 415 pumps. Viton Neoprene, and PTFE mechanical seals also available. For mechanical seal pumps on applications with viscosities above 15,000 SSU (,00 cst), provide details for recommendation. For maximum recommended discharge pressures when handling other viscosities and/or at other speeds, see performance curves, which can be electronically generated with the Viking Pump Selector Program, located on Metric conversions are based on US measurements and rounded to the nearest whole number. www.vikingpump.com. If suction pressure exceeds 50 PSIG ( BAR), consult factory. 4 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. 5 Nominal rating based on handling thin liquids. 6 Standard seal can be used form -0 F. to +5 F. With special construction, temperatures from -60 F. to +650 F. can be handled with this series pumps. 7 AK and AL sizes not available in steel-fitted construction. Viton Registered trademark of DuPont Performance Elastomers. Pump, motor, or reducer can be removed without dis turbing the other two components. Units with A, B and C reducers have standard flexible coupling with guard between power and reducer as well as between reducer and pump. Oil and weathertight for outdoor service. Ball bearings throughout. Reducers easily adjustable to different motor center heights. Self-supported. Not hung on pump or motor shafts. No radial load on pump or motor shafts. A reducers have ¾ dia., ³ ₁₆ key input and output shafts; B reducers have 1 dia., ¼ key input shaft and 1⅛ dia., ¼ key output shaft; C reducers have 1⅜ dia., ⁵ ₁₆ key input and output shafts.
Page 141.5 VIKING HELICAL GEAR REDUCTION UNITS ( R DRIVE) HELICAL REDUCER HORSEPOWER TABLE A SIZE HIGH SPEED SHAFT INPUT RPM 1 1750 1450 1150 950 1 For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information. GEAR REDUCER RATIOS A SIZE.4:1.76:1.4:1 4.17:1 780 640 50 40 LOW SPEED SHAFT RPM 6.1 4.9.8.1 MAXIMUM REDUCER HP 640 50 40 50 LOW SPEED SHAFT RPM 5. 4...7 MAXIMUM REDUCER HP 50 40 50 80 LOW SPEED SHAFT RPM 4..4.6. MAXIMUM REDUCER HP 40 50 80 0 LOW SPEED SHAFT RPM.6.9. 1.8 MAXIMUM REDUCER HP HELICAL REDUCER HORSEPOWER TABLE B SIZE HIGH SPEED SHAFT INPUT RPM 1750 1450 1150 950 GEAR REDUCER RATIOS B SIZE 1 1.87:1 1.4:1.76:1.40:1 4.19:1 5.06:1 6.7:1 7.65:1 950 780 640 50 40 50 80 0 LOW SPEED SHAFT RPM 19.0 17.0 15.0 1.0 11.0 9.5 7.6 6.4 MAXIMUM REDUCER HP 780 640 50 40 50 80 0 190 LOW SPEED SHAFT RPM 17. 15.5 1.4 11.6 9.9 8.5 6.4 5.4 MAXIMUM REDUCER HP 640 50 40 50 80 0 190 155 LOW SPEED SHAFT RPM 16.5 14.0 11.6 10.1 8.5 7. 5. 4.4 MAXIMUM REDUCER HP 50 40 50 80 0 190 155 15 LOW SPEED SHAFT RPM 15.5 1.8 10.1 9.0 7.6 6.0 4..7 MAXIMUM REDUCER HP 1 For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information. HELICAL REDUCER HORSEPOWER TABLE C SIZE HIGH SPEED SHAFT INPUT RPM 1750 1450 1150 950 GEAR REDUCER RATIOS C SIZE 1.1:1.80:1.1:1 4.1:1 5.08:1 6.4:1 7.95:1 780 640 50 40 50 80 0 LOW SPEED SHAFT RPM 49.8 4.5 9.0.4 6.6 19.7 18.0 MAXIMUM REDUCER HP 640 50 40 50 80 0 180 LOW SPEED SHAFT RPM 45. 6.6.8 7.. 16.7 15. MAXIMUM REDUCER HP 50 40 50 80 0 190 145 LOW SPEED SHAFT RPM 40.1 0.0 6.8. 18. 1.8 1.6 MAXIMUM REDUCER HP 40 50 80 0 190 155 10 LOW SPEED SHAFT RPM 9.1 4.7.1 18. 15.0 11.4 10.4 MAXIMUM REDUCER HP 1 For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information.
Page 141.6 VIKING HEAVY DUTY PUMPS GEAR REDUCER UNITS ( P DRIVE) AND DIRECT DRIVE UNITS ( D DRIVE) with P Drive K through LS Sizes with P Drive Q through M Sizes (shown without pressure relief valve) Heavy-duty Series 15 and 415 packed and mechanical seal pumps in sizes from K through M are available in the P drive arrangement. These heavy-duty units are mounted on formed steel bases ( K through LS sizes) and structural or formed steel bases ( Q through M sizes) as illustrated above. All mount separate heavy-duty reducers with flexible couplings between pump, reducer, and motor. Coupling guards as illustrated are standard construction. Contact factory for specifications and motor horsepower range. Dimensions for P Drive Units Consult Factory. with D Drive G, H and HL Sizes The Direct Drive D mounting is specifically designed for compactness and quietness of operation. In this type assembly the pump is mounted on one end of a rectangular formed steel base and connected to a motor by means of a flexible coupling with guard. G, H, and HL sizes can be directly connected to 1800 RPM motors as well as gearhead motors. AK and AL size pumps are direct connected to 100 RPM motors or gearhead motors providing high-capacity, compact pumping unit. Dimensions for D Drive Units ( G through AL sizes) See Page 141.9. with D Drive AK and AL Sizes with D Drive, Gearhead Motor K through M Sizes
Page 141.7 V-BELT DRIVE UNITS ( V DRIVE) Model Numbers with V Drive G through M Size Pumps V-belt driven line of heavy-duty Series 15 and 415 pumps are all mounted on formed welded steel bases. Pumps mount on pads to accept totally enclosed V-belt drive. All units in this series feature standard pump shaft extension with totally guarded V-driven pulley mounted on end of heavy-duty pump shaft. Dimensions for V Drive Units See Page 141.1. SPECIFICATIONS V DRIVE UNITS Port Size 5 Nominal Pump Rating Maximum Hydrostatic Pressure Steel-Fitted Construction Above This Viscosity Maximum Discharge Pressure When Handling 100 SSU Liquid At Nominal Rated Speeds 6 Maximum Temperature For Cataloged Pump, F. ( C.) Approximate Shipping Weight With Valve (Less Power) Packed 1 Mech. Seal Inches GPM (m³/hr) RPM PSIG (BAR) SSU (cst) PSIG Packed Mech. Seal Pounds (KG) G15V G415V 1 8 () 1800 400 (8) 7,500 (1,650) 00 00 (149) 5 (107) 9 (4) H15V H415V 1½ 15 () 1800 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 109 (49) HL15V HL415V 1½ 0 (7) 1800 400 (8) 7,500 (1,650) 00 00 (149) 5 (107) 114 (5) K15V K415V 75 (17) 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 55 (116) KK15V KK415V 100 () 780 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 65 (10) L15V L415V 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 05 (18) LQ15V LQ415V 4 ½ 15 (1) 640 400 (8) 5,000 (5,500) 00 00 (149) 5 (107) 40 (154) LL15V LL415V 4 140 () 50 400 (8),500 (550) 00 00 (149) 5 (107) 65 (166) LS15V LS415V 4 00 (45) 640 400 (8) 75,000 (16,500) 150 00 (149) 5 (107) 75 (170) Q15V Q415V 4 4 00 (68) 50 400 (8) 7,500 (1,650) 150 00 (149) 5 (107) 986 (448) QS15V QS415V 4 6 500 (114) 50 400 (8) 75,000 (16,500) 150 00 (149) 5 (107) 1,100 (499) M15V M415V 4 4 40 (95) 40 400 (8) 5,000 (5,500) 150 00 (149) 5 (107) 1,18 (517) 1 Buna-N elastomer used in mechanical seal of Series 415 pumps. Viton, Neoprene, and PTFE mechanical seals also available. For mechanical seal pumps on applications with viscosities above 15,000 SSU (,00 cst), provide details for recommendation. For maximum recommended discharge pressures when handling other vis cosities and/or at other speeds, see performance curves, which can be electronically generated with the Viking Pump Selector Program, located on www.vikingpump.com. If suction pres sure exceeds 50 PSIG ( BAR), consult factory. 4 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. 5 Nominal rating based on handling thin liquids. 6 Standard seal can be used from -0 F. to +5 F. With special construc tion, temperatures from -60 F. to +650 F. can be handled with this series pumps. Viton Registered trademark of DuPont Performance Elastomers. Metric conversions are based on US measurements and rounded to the nearest whole number.
Page 141.8 VIKING HEAVY DUTY PUMPS DIMENSIONS These dimensions are average and not for construction purposes. Certified prints on request. For specifications, see page 141.. DIMENSIONS UNMOUNTED PUMPS MODEL NO. PACKED SEAL G15 G415 1 H15 HL15 AK15 AL15 K15 KK15 H415 HL415 AK415 AL415 K415 KK415 A B C D E F G H J K L M N O P R S T U V W 1½ L15 L415 LQ15 LQ415 1 ½ LL15 LL415 1 LS15 LS415 1 Q15 Q415 1 4 M15 M415 1 4 1 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. in.50.50.75 1.6 1.1 4.00.44.4 1.00 1.1 4.88 1.09.1.69 7.1 9.5 1.1.50.1 x.06.69 mm 64 89 70 41 10 6 9 5 8 14 8 8 18 186 4 8 1.05 x 1.5 68 in.00 4.75.50.75.5 6.75.50.47 1.50.8 5.19 1.19.56.6 10.44 1.5 1.6.75.19 x.09.88 mm 76 11 89 70 57 171 89 1 8 86 1 0 14 16 65 7 41 19.05 4.76 x.8 7 in 4.50 6.6 5.5.88.00 6.75 4.00.41.5.81 8.88.00.44 1.00 1.18 17.68.50 1.00.5 x.1 4.80 mm 114 168 1 7 51 171 10 10 57 71 6 51 11 5 5 449 64 5.40 6.5 x.18 1 in 5.1 8.00 5.50 4.00.75 9.5 4.00.5.00.00 9.8 1.75.6.6 14.1 18.1.5 1.1.5 x.1 5.1 mm 10 0 140 10 70 5 10 1 51 76 8 44 16 16 59 460 57 8.58 6.5 x.18 10 in 6.50 10.5 7.00 4.8 4.00 10.00 5.8.5.00.8 9.1 1.75.6.6 15.6 19.6.5 1.1.5 x.1 5.8 mm 165 60 178 111 10 54 17 1 51 86 44 16 16 97 498 57 8.58 6.5 x.18 17 in 7.19 10.5 7.00 4.8 4.00 10.00 5.8.5.00.8 9.1 1.75.6.6 15.6 19.6.5 1.1.5 x.1 5.8 mm 18 60 178 111 10 54 17 1 51 86 44 16 16 97 498 57 8.58 6.5 x.18 17 in 7.19 10.5 7.00 4.8 4.00 10.00 5.8.5.00.8 9.1.5.6.6 15.6 0.1.5 1.1.5 x.1 5.8 mm 18 60 178 111 10 54 17 1 51 86 57 16 16 97 511 57 8.58 6.5 x.18 17 in 7.19 10.5 7.00 4.8 4.00 10.00 5.8.5.5 4.75 9.1.44.6.6 15.75 1.69.50 1.44.8 x.19 5.19 mm 18 60 178 111 10 54 17 1 8 11 6 16 16 400 551 89 6.51 9.5 x 4.76 1 in 8.5 14.00 8.75 4.1 4.00 10.00 6.00.69 4.8 6.6 11.1.00.75 1.00 19.5 6.75 4.50 1.94 50 x.5 8.19 mm 10 56 105 10 54 15 18 111 168 8 76 19 5 489 679 114 49.1 1.70 x 6.5 08 in 9.50 17.5 10.00 5.00 6.00 1.00 8.50.69 4.00 7.75 8.1 4.00 1.00 1.50 0.1 8.8 4.5 1.94.50 x.5 8.50 mm 41 48 54 17 15 05 16 18 10 197 06 10 5 8 511 71 108 49.1 1.70 x 6.5 16 For specifications, see page 141.. DIMENSIONS UNMOUNTED PUMPS QS SIZE NOTE: Dimensions shown in parentheses are millimeters; others are inches.
Page 141.9 DIMENSIONS These dimensions are average and not for construction purposes. Certified prints on request. For specifications, see pages 141. through 141.5. DIMENSIONS ( R DRIVE) G THROUGH AL SIZE PUMPS A SIZE REDUCER UNITS 1 Base suitable for motor frames 56 through 184-T on Models G, H, and HL through 15-T for Models AK and AL. For motor frames 1-T and 15-T, G dimension is increased to 4.00. All other dimensions remain the same. (Base has open ends.) Does not apply to Models AK and AL. Location of pump port centerline on Models G15R and G415R. 4 With motor frames 18-T and smaller, use the (four) corner base anchor holes. Motor frame 184-T cov ers up the lower left corner anchor hole, so the hole 9.00 to the right is used. Does not apply to Models AK and AL. 5 On Models G15R and G415R, E dimension includes pump block. Base height is.94. For specifications, see pages 141. through 141.5. DIMENSIONS ( R DRIVE) AK THROUGH LS SIZE PUMPS B SIZE REDUCER UNITS (Check footnote 5 for applicability.) MODEL NUMBER 5 PACKED SEAL A B C E F G H J K L M N.50.75.69 900 9.00 1.50 1.00.56.1.75 1.81 G15R G415R 1 64 70 94 9 77 8 5 14 95 46 H15R H415R.00.50.94 9.00 9.00 1.50 1.00.56.6 4.06.6 AND AND 1½ HL15R HL415R 76 89 75 9 77 8 5 14 67 10 67 AK15R AK415R 4.50 5.5 4.00 16.00 9.00 1.8 1.8.6.19 6.80 6.00 AND AND AL15R AL415R 114 1 10 406 991 5 5 16 81 17 15 4 1 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. 1 With motor frames 184-T and smaller, these units are assembled on a shorter base with the following dimension changes: (F = 16, G = 9, L =, N = 5⅜ ). Motor rails 1⅞ high are required with 56, 14-T and 145-T frame motors. NOTE: Motor frame larger than 56-T requires larger base. Consult factory. Units available to accept 10HP, 100 RPM maximum motor. NOTE: Motor rails high are required on L through LS size units with 184-T or 4½ center height motors. MODEL NUMBER PACKED SEAL A B C E F G J K L M N AK15R AK415R in 4.50 9.50 4.00 14.5 48.00 1.8.6.19 6.80 4.88 AND AND AL15R AL415R mm 114 41 10 6 119 5 16 81 17 14 K15R K415R in 5.1 9.50 4.00 14.5 48.00 1.8.6.00 6.88 4.5 AND AND KK15R KK415R mm 10 41 10 6 119 5 16 51 175 108 in 6.50 11.00 4.00 14.5 48.00 1.8.6.8 7.1 4.6 L15R L415R mm 165 79 10 6 119 5 16 60 181 117 LQ15R LQ415R 1 in 7.19 11.00 4.00 14.5 48.00 1.8.6.8 7.1 4.6 ½ mm 18 79 10 6 119 5 16 60 181 117 1 in 7.19 11.00 4.00 14.5 48.00 1.8.6.8 7.6 4.6 LL15R LL415R mm 18 79 10 6 119 5 16 60 194 117 LS15R LS415R 1 in 7.19 11.00 4.00 14.5 48.00 1.8.6.8 7.6 4.6 mm 18 79 10 6 119 5 16 60 194 117
Page 141.10 VIKING HEAVY DUTY PUMPS DIMENSIONS These dimensions are average and not for construction purposes. Certified prints on request. MODEL NUMBER PACKED SEAL KK15R KK415R L15R L415R LQ15R LL15R LS15R Q15R LQ415R LL415R LS415R Q415R A B C E F G J K L M N 1 ½ 1 1 1 4 in 5.1 1.75 6.00 1.00 49.00 1.50.69.00 6.88 6.06 mm 10 49 15 5 145 8 18 76 175 154 in 6.50 1.75 6.00 19.75 59.50 1.50.69 0 7.1 5.75 mm 165 49 15 50 1511 8 18 0 181 146 in 7.19 1.75 6.00 19.75 59.50 1.50.69 0 7.1 5.75 mm 18 49 15 50 1511 8 18 0 181 146 in 7.19 1.75 6.00 19.75 59.50 1.50.69 0 7.6 5.75 mm 18 49 15 50 1511 8 18 0 194 146 in 7.19 1.75 6.00 19.75 59.50 1.50.69 1.8 7.6 5.75 mm 18 49 15 50 1511 8 18 5 194 146 in 8.5 14.75 6.00 19.75 59.50 1.50.69 5.88 11.19 5.75 For specifications, see pages 141. through 141.5. DIMENSIONS ( R DRIVE) KK THROUGH M SIZE PUMPS (NOT FOR QS SIZE) C SIZE REDUCER UNITS M15R M415R 1 4 mm 10 75 15 50 1511 8 18 7 84 146 in 9.50 16.00 6.00 19.75 59.50 1.50.69 6.50 1.50 5.75 mm 41 406 15 50 1511 8 18 89 18 146 1 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fit tings. All others tapped for standard pipe. For specifications, see pages 141. through 141.5. DIMENSIONS QS SIZE PUMPS C SIZE REDUCER UNITS NOTE: Dimensions shown in parentheses are millimeters; others are inches.
Page 141.11 DIMENSIONS These dimensions are average and not for construction purposes. Certified prints on request. For description, see page 141.6. DIMENSIONS ( D DRIVE) G SIZE PUMPS DIRECT CONNECTED UNITS For description, see page 141.6. DIMENSIONS ( D DRIVE) H THROUGH AL SIZE PUMPS DIRECT CONNECTED UNITS G15D OR G415D B D FRAME E F H J K L M P S in.50.50 1.50 17.50.75.75 8.50 1.88.75.5 4.5 56 mm 64 89 8 445 19 19 16 48 95 1 108 in.50.50 14T 1.50 0.50.75.75 8.50 1.88.75.50 4.5 OR mm 64 89 145T 8 51 19 19 16 48 95 1 108 in.50 4.50 18T 1.50 0.50.75.75 8.50 1.88.75.50 4.5 OR mm 64 114 184T 8 51 19 19 16 48 95 1 108 in.50 5.5 1T.94 5.00 1.00 1.50 9.00 1.88.75.56 4.50 OR mm 64 1 15T 75 65 5 8 9 48 95 14 114 1 For motor frames 56, 14-T, and 145-T. (Base has open ends.) For motor frames 18, 18-T, 184, and 184-T. (Base has closed ends.) For motor frames 1 through 15-T. (Base has closed ends.) 4 For motor frames 18 through 184-T. Dimension includes block under motor. (Base has open ends.) 5 For motor frames 1 through 15-T. (Base has open ends.) 6 For motor frames 54 through 56-T. (Base has closed ends.) 7 For motor frames 84 through 86-T. (Base has closed ends.) MODEL NUMBER PACKED SEAL H15D H415D OR OR HL15D HL415D AK15D AK415D OR OR AL15D AL415D A B D E F K L M N S 1½ in.00 1.50 1.50 0.50.50 1.75 4.06 8.50 4.5 mm 76 89 8 51 1 44 10 16 108 1½ in.00 4.50.94 5.00.56.56 4.06 9.00 4.50 mm 76 114 75 65 14 14 10 9 114 in.00 5.5.94 5.00.56.8 4.06 9.00 4.50 1½ mm 76 1 75 65 14 86 10 9 114 in 4.50 4 5.5.94 6.00.56.56 6.80 9.00 4.50 mm 114 1 75 660 14 90 17 9 114 in 4.50 5 5.5.94 9.00.56.56 6.80 9.00 4.50 mm 114 1 75 77 14 90 17 9 114 in 4.50 6 6.5 4.00 9.00.6.19 6.80 16.00 8.00 mm 114 159 10 991 16 81 17 406 0 in 4.50 7 7.00 4.00 9.00.6.19 6.80 16.00 8.00 mm 114 178 10 991 16 81 17 406 0
Page 141.1 VIKING HEAVY DUTY PUMPS DIMENSIONS These dimensions are average and not for construction purposes. Certified prints on request. MODEL NUMBER PACKED SEAL A B C E F G J K L M N H15V H415V.00 9.5 1.75 14.75.75.75.50 4.88 4.06 4.5 AND AND HL15V HL415V mm 76 5 44 75 60 19 1 14 10 108 K15D K415V in 5.1 1.81.5 17.00 8.75 1.00.50.50 6.88 5.5 AND AND KK15D KK415V mm 10 51 8 4 70 5 1 64 175 1 in 650 15.1.5 17.00 8.75 1.00.50.5 7.1 5.5 L415V L15V mm 165 89 8 4 70 5 1 57 181 1 1 in 7.19 15.1.5 17.00 8.75 1.00.50.5 7.1 5.5 LQ415V LQ15V ½ mm 18 89 8 4 70 5 1 57 181 1 1 in 7.19 15.1.5 17.00 8.75 1.00.50.5 7.6 5.5 LL415V LL15V mm 18 89 8 4 70 5 1 57 194 1 1 in 7.19 15.1.5 17.00 8.75 1.00.50 1.06 7.6 5.5 LS415V LS15V mm 18 89 8 4 70 5 1 7 194 1 Q15V Q415V 1 in 8.5 1.5 6.00 1.00 49.00 1.50.81.75 11.19 8.50 4 mm 10 540 15 5 145 8 1 70 84 16 M15V M415V 1 in 9.50.50 6.00 1.00 49.00 1.50.81.1 1.50 8.50 4 mm 41 57 15 5 145 8 1 54 18 16 For specifications, see page 141.7. DIMENSIONS ( V DRIVE) G SIZE PUMPS V-BELT DRIVE UNITS NOTE: For motor frames 56 and 14-T. Maximum frame size is 14-T. D dimension for motor frame 56 is.50 (89 mm) less rail; for motor frame 14-T, 5.00 (17 mm) with rail. NOTE: Dimensions shown in parentheses are millimeters; others are inches. For specifications, see page 141.7. DIMENSIONS ( V DRIVE) H THROUGH M SIZE ➃ PUMPS V-BELT DRIVE UNITS 1 Ports are suitable for use with 15# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. Base dimensions correct for all motors. Base dimensions correct through frame 15-T motors and 19 OD sheaves. Larger motors and/or 5 OD sheaves require larger base. 4 QS size pump drawing available on request.
Page 141.1 Performance Curve Notes Printed performance curves are not available. curves can be electronically generated with the Viking Pump Selector Program. This program can be located on www.vikingpump.com for the general public. For authorized distributors, this program can be found listed under the Products tab at www.idexconnect.com. Security passwords are required to access IDEXconnect.