5- GROUP 5 CONTENTS FRONT BUMPER ASSEMBLY 5- REMOVAL AND INSTALLATION 5- DISASSEMBLY AND ASSEMBLY 5- REAR BUMPER ASSEMBLY 5-4 REMOVAL AND INSTALLATION 5-4 DISASSEMBLY AND ASSEMBLY 5-4 UNDER FLOOR SPARE TIRE CARRIER 5-5 REMOVAL AND INSTALLATION 5-5 GRILL, MOLDING AND GARNISH 5-5 SPECIAL TOOL 5-5 GRILL, MOLDING AND GARNISH 5-6 REMOVAL AND INSTALLATION 5-6 WIDE FENDER 5-0 REMOVAL AND INSTALLATION 5-0 SIDE STEP 5- REMOVAL AND INSTALLATION 5- ROOF RAIL 5-5 REMOVAL AND INSTALLATION 5-5 WINDSHIELD WIPER AND WASHER 5-5 GENERAL DESCRIPTION 5-5 WINDSHIELD WIPER AND WASHER 5-6 REMOVAL AND INSTALLATION 5-6 INSPECTION 5-7 REAR WIPER AND WASHER 5-9 GENERAL DESCRIPTION 5-9 REAR WIPER AND WASHER 5-0 REMOVAL AND INSTALLATION 5-0 INSPECTION 5- MARK 5- REMOVAL AND INSTALLATION 5- DOOR MIRROR 5-5 SPECIAL TOOL 5-5 DOOR MIRROR 5-6 REMOVAL AND INSTALLATION 5-6 INSPECTION 5-7 SPECIFICATIONS 5-9 FASTENER TIGHTENING SPECIFICATIONS 5-9 SERVICE SPECIFICATIONS 5-9 SEALANTS AND ADHESIVES 5-9
FRONT 5- REMOVAL AND INSTALLATION FRONT BUMPER ASSEMBLY BUMPER ASSEMBLY M50040006 AC00744 AB REMOVAL STEPS REMOVAL STEPS (Continued) LICENSE PLATE GARNISH FRONT BUMPER SIDE STAY FRONT BUMPER ASSEMBLY
DISASSEMBLY AND ASSEMBLY 5- FRONT BUMPER ASSEMBLY M50060000 5 N m in-lb 7 6 07 N m 6 in-lb 5 N m in-lb 7 6 07 N m 6 in-lb 5 4 8 AC00745AB DISASSEMBLY STEPS FRONT BUMPER BEAM ASSEMBLY FRONT BUMPER SIDE REINFORCEMENT FRONT BUMPER SIDE EXTENSION <VEHICLES WITH WIDE FENDER> 4 FRONT BUMPER GRILL <VEHICLES WITH FOG LIGHT> DISASSEMBLY STEPS (Continued) 5 FRONT BUMPER GRILL <VEHICLES WITHOUT FOG LIGHT> 6 FOG LIGHT BRACKET <VEHICLES WITH FOG LIGHT> 7 FOG LIGHT <VEHICLES WITH FOG LIGHT> 8 FRONT BUMPER FACE
5-4 REAR BUMPER ASSEMBLY REAR BUMPER ASSEMBLY REMOVAL AND INSTALLATION M5009007 Pre-removal and Post-installation Operation Spare tire Removal and Installation Cargo Floor Box, Rear Removal and Installation AC00746AB REMOVAL STEPS REAR BUMPER STEP REAR BUMPER ASSEMBLY DISASSEMBLY AND ASSEMBLY M5000078 5 5 4 4 4 AC00747AB
5-5 UNDER FLOOR SPARE TIRE CARRIER DISASSEMBLY STEPS REAR BUMPER SIDE BRACKET REAR BUMPER REINFORCEMENT ASSEMBLY DISASSEMBLY STEPS (Continued) REFLEX REFLECTOR BRACKET 4 REFLEX REFLECTOR 5 REAR BUMPER FACE UNDER FLOOR SPARE TIRE CARRIER REMOVAL AND INSTALLATION N m 04 in-lb M50600045 SPARE TIRE CARRIER AC00750AB SPECIAL TOOL TOOL GRILL, MOLDING AND GARNISH TOOL NUMBER AND NAME MB990449 Window molding remover REPLACED BY MILLER TOOL NUMBER General service tool APPLICATION Removal of roof drip molding M500060074 MB990449
5-6 GRILL, MOLDING AND GARNISH REMOVAL AND INSTALLATION GRILL, MOLDING AND GARNISH M50790005 SECTION A A CLIP N m in-lb 4 ROOF PANEL A A NOTE : Claw position <<A>> RADIATOR GRILL <<B>> ROOF DRIP MOLDING FRONT DECK GARNISH REMOVAL STEPS WIPER ARM AND BLADE ASSEMBLY (REFER TO P5-7) 4 FRONT DECK GARNISH AC0075 AB Required Special Tool: MB990449: Window Molding Remover
5-7 GRILL, MOLDING AND GARNISH 8 5 49 N m 4 in-lb 0 9 75 N m 65 in-lb 6 7 NOTE : Clip position : Claw position 8 mm ( in) 6 mm (06 in) 6 mm (4 in) 5 mm (06 in) 6 mm (4 in) B 5 mm (8 in) 5 mm (06 in) 5 mm (06 in) B 6 mm (4 in) 44 mm (7 in) 55 mm (06 in) 5 6 B A B C D E ADHESIVE TAPE: DOUBLE-SIDED TAPE <A, C, E [ mm ( 005 in ) THICKNESS ], C [ 5 mm ( 0 in ) WIDTH AND mm ( 005 in ) THICKNESS ], D [ mm ( 05 in ) WIDTH AND mm ( 005 in ) THICKNESS ]> AC07AB <<C>> >>A<< 5 FRONT DOOR MOLDING <<C>> >>A<< 6 REAR DOOR MOLDING REAR DECK GARNISH REMOVAL STEPS 7 LICENSE PLATE LIGHT 8 REAR WIPER ARM AND BLADE ASSEMBLY (REFER TO P5-7) REAR DECK GARNISH REMOVAL STEPS (Continued) 9 GROMMET (REFER TO P5-7) LIFTGATE LOWER TRIM 0 LIFTGATE GARNISH
5-8 GRILL, MOLDING AND GARNISH REMOVAL SERVICE POINT <<A>> RADIATOR GRILL REMOVAL Remove the radiator grill by pushing all tabs of the radiator grill clips in the direction of the arrows with a flat-tipped screwdriver, then lightly pull the radiator grill toward you <<B>> ROOF DRIP MOLDING REMOVAL CAUTION If the molding has become warped, it should not be reused AC0075 Use special tool MB990449 to lever out the molding MB990449 AC0066AB PROTECTION TAPE <<C>> DOOR MOLDING REMOVAL Gently lift and remove the door molding If there is any doublesided tape remaining on the door molding, remove according to the following instructions <Remove double-sided tape remaining on the body surface> Attach protection tape all the way along the edges of the double-sided tape which is still adhering to the body DOUBLE-SIDED TAPE AC00040AB DOUBLE-SIDED TAPE Scrape off the double-sided tape with a resin spatula as possible Peel off the protection tape 4 Use a shop towel moistened with M AAD Part number 8906 or equivalent to wipe the body AC0004AB
5-9 GRILL, MOLDING AND GARNISH <Remove double-sided tape remaining on double-sided tape (when re-using door molding)> Scrape off the double-sided tape on the door molding with a resin spatula as possible AC0004 Use a shop towel moistened with M AAD Part number 8906 or equivalent to wipe the door molding surface Remove only a small portion of the residual adhesive 4 Adhere the double-sided tape as specified on the door molding (Refer to double-sided tape adherence location P5-8) AC0068 INSTALLATION SERVICE POINTS ADHESIVE TAPE BACKING PAPER AC0004AB >>A<< DOOR MOLDING INSTALLATION Tear off the double-sided tape backing paper NOTE: If you attach the adhesive tape to the edge of the backing paper, it will be easy to tear off Install the door molding NOTE: If the double-sided tape is difficult to affix in cold temperature, etc, warm the bonding surfaces of the body and door molding to about 40 60 C (04 40 F) before affixing the tape Firmly press in the door molding
5-0 REMOVAL AND INSTALLATION WIDE FENDER WIDE FENDER M508000 Pre-removal and Post-installation Operation Mud Guard Removal and Installation N N NOTE : Resin clip position AC00754 AC REMOVAL STEPS REMOVAL STEPS (Continued) <<A>> >>A<< RIVET FRONT FLARE REAR FLARE
5- WIDE FENDER REMOVAL SERVICE POINT <<A>> RIVET REMOVAL Use a drill [φ 40 55 mm(φ 06 0 inch) bit for rivet] to make a hole in the rivet to break it, and then remove the rivet FLARE RIVET DRILL ACX004AE INSTALLATION SERVICE POINT RIVETER BODY PANEL >>A<< RIVET INSTALLATION Insert the rivet [φ 48 mm(φ 09 inch) bit for rivet] into the body panel and flare Insert A of the rivet into the riveter Pressing the flange surface of the rivet, move the handle of the riveter 4 The thinnest point of A is cut and the rivet is held in position FLARE RIVET A 4 FLANGE SURFACE RIVETER RIVET 8E09 AC0085AB
5- REMOVAL AND INSTALLATION SIDE STEP SIDE STEP M50500099 N 5 N N m 98 in-lb 5 N 6 4 N m 98 in-lb 7 N m 98 in-lb REMOVAL STEPS SIDE STEP ASSEMBLY SIDE STEP COVER, UPPER <<A>> >>A<< RIVET A <<A>> >>A<< 4 RIVET B 8 4 6 N AC0786AB REMOVAL STEPS (Continued) 5 SIDE STEP COVER 6 SIDE STEP CAP 7 SIDE STEP PLATE 8 SIDE STEP PIPE ASSEMBLY
5- SIDE STEP REMOVAL SERVICE POINTS <<A>> RIVET A/RIVET B REMOVAL Use a drill [φ 40 mm (φ06 inch) bit for rivet A and rivet B] to make a hole in the rivet to break it, and then remove the rivet SIDE STEP COVER AND SIDE STEP CAP RIVET DRILL ACX004AF
5-4 RIVET A Ø40 (00) RIVET B Ø40 (00) 0 (040) UNIT: mm (in) Ø80 (0) AC00597 THREE SLITS AROUND RIVET Ø80 (0) SIDE STEP INSTALLATION SERVICE POINTS >>A<< RIVET A/RIVET B INSTALLATION Insert rivets A and B into the side step pipe assembly, side step cover and side step cap Insert C of the rivet into the riveter Pressing the flange surface of the rivet, move the handle of the riveter 4 The thinnest point of C is cut and the rivet is held in position 8 (07) AC08 RIVETER V06AA RIVET C 4 RIVETER FLANGE SURFACE RIVET 8E09 AC00766AB
REMOVAL AND INSTALLATION 5-5 ROOF RAIL ROOF RAIL M506600080 Pre-removal and Post-installation Operation Headlining Removal and Installation ROOF RAIL ASSEMBLY N AC00767AD WINDSHIELD WIPER AND WASHER GENERAL DESCRIPTION OPERATION Low-speed (and high-speed) wiper operation When the wiper switch is placed in the "LOW" position with the ignition switch in the "ACC" or "ON" position, wipers operate continuously at low speed Placing the wiper switch in the "HIGH" position causes the wipers to operate at high speed Auto wiper stop operation When the wiper switch is placed in the "OFF" position, the cam contacts of wiper motor causes current to flow through the auto wiper stop circuit, allowing the wiper blades to cycle before they reach to the stop positions M50000057 Intermittent wiper operation When the wiper switch is placed in the "INTER- MITTENT" position with the ignition switch in the "ACC" or "ON" position, the intermittent wiper relay is energized causing the intermittent wiper relay contacts to close and open repeatedly When the contacts are closed, the wiper motor is energized When the wiper motor is energized, the relay contacts open; however, the cam contacts keep the wiper motor energized until the wiper blades return to their stop position Washer-wiper operation When the washer switch is turned "ON," the intermittent wiper relay contacts close causing wipers to cycle one to two times
5-6 WINDSHIELD WIPER AND WASHER REMOVAL AND INSTALLATION WINDSHIELD WIPER AND WASHER M50080006 N m in-lb 6 5 49 N m 4 in-lb 49 N m 4 in-lb 49 N m 4 in-lb 4 49 N m 4 in-lb 7 49 N m 4 in-lb AC0086 AC 8 5 WIPER MOTOR AND LINK ASSEMBLY REMOVAL STEPS >>A<< WIPER ARM AND BLADE ASSEMBLY FRONT DECK GARNISH <<A>> WIPER MOTOR ASSEMBLY 4 WIPER LINK ASSEMBLY WIPER MOTOR AND LINK ASSEMBLY REMOVAL STEPS 5 WASHER HOSE 6 WASHER NOZZLE WASHER TANK REMOVAL STEPS FRONT BUMPER ASSEMBLY (REFER TO P5-) WASHER FLUID DRAINING AND SUPPLYING 5 WASHER HOSE 7 WASHER TANK ASSEMBLY 8 WASHER MOTOR NOTE: For removal and installation of the column switch assembly (wiper and washer switch), refer to GROUP 7A, Steering Wheel and Shaft P7A-
LINK ASSEMBLY 5-7 WINDSHIELD WIPER AND WASHER REMOVAL SERVICE POINT <<A>> WIPER MOTOR ASSEMBLY REMOVAL CAUTION Auto-stop angle controlled so do not remove the crank arm from the wiper motor unless necessary When removing, mark the crank arm and wiper motor Use a flat-tipped screwdriver to remove the connection between the wiper motor crank arm and link assembly WIPER MOTOR CRANK ARM AC0086AB PASSENGER'S SIDE (B) DRIVER'S SIDE (A) INSTALLATION SERVICE POINT >>A<< WIPER ARM AND BLADE ASSEMBLY INSTALLA- TION Install the wiper blade at the specified position (standard value) Standard value: Driver's side (A): 6 ± 5 mm (0 ± 0 inches) Passenger's side (B): 0 40 mm ( 5 inches) FRONT DECK GARNISH END AC00047AB INSPECTION M500770050 WINDSHIELD WIPER AND WINDSHIELD WASHER SWITCH CHECK Follow the table below to check the windshield wiper and washer switch for continuity AC0090 SWITCH POSITION TERMINAL CONNECTION SPECIFIED CONDITION OFF 7 8 Less than ohms Windshield intermittent wiper switch ON Windshield low-speed wiper switch ON Windshield high-speed wiper switch ON 7 8 Less than ohms 8 0 Less than ohms 9 0 Less than ohms Windshield washer switch ON 6 0 Less than ohms
5-8 WINDSHIELD WIPER AND WASHER INTERMITTENT WIPER RELAY (INTERMITTENT OPERATION INSPECTION) Connect the column switch connector Turn the ignition switch to "ACC" Inspect the intermittent operation time when the wiper switch is turned to "INTERMITTENT" Vehicle with variable intermittent control FAST: Approximately seconds SLOW: Approximately 5 seconds FRONT WIPER MOTOR CHECK Check the wiper motor after disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body Wiper Motor at Low-Speed and High-Speed Operation Connect a battery to the wiper motor as shown in the illustration and inspect motor operation at low-speed and high-speed CHECK OPERATION LOW SPEED HIGH SPEED STOP POSITION CHECK Wiper Motor at Stop Position Operation Run the wiper motor at low-speed, disconnect the battery, and stop the motor Reconnect the battery as shown in the illustration, and confirm that after the motor starts turning at low-speed, and stops at the automatic stop position LOW SPEED AUTOMATIC STOP AC00875AB FRONT WASHER MOTOR CHECK The windshield washer tank assembly should be installed and the windshield washer tank should be filled with water when checking the washer motor Check that water is sprayed out strongly when battery voltage is applied to terminal () and terminal () is grounded AC0088
5-9 REAR WIPER AND WASHER RH B C CENTER LINE A E F D G H I J LH WINDSHIELD WASHER FLUID EJECTION CHECK Adjust the ejection angle by moving a ball in the nozzle A: 5 mm (8 inches), B: 85 mm (5 inches), C: 40 mm (55 inches), D: 95 mm (77 inches), E: 40 mm (70 inches), F: 90 mm (4 inches), G: 75 mm (48 inches), H: 95 mm (77 inches), I: 70 mm (8 inches), J: 50 mm (0 inches) CERAMIC END LINE AC00896AB REAR WIPER AND WASHER GENERAL DESCRIPTION OPERATION Low-speed wiper operation When the rear wiper switch is placed in the "ON" position with the ignition switch in the "ACC" or "ON" position, wiper operate continuously at low speed Auto wiper stop operation When the rear wiper switch is placed in the "OFF" position, the cam contacts of wiper motor causes current to flow through the auto wiper stop circuit, allowing the wiper blades to cycle before they reach to the stop positions Intermittent wiper operation When the rear wiper switch is placed in the "INTERMITTENT" position with the ignition switch in the "ACC" or "ON" position, the rear intermittent wiper relay contacts to close and open repeatedly M50000068 When the contacts are closed, the wiper motor is energized When the rear wiper motor is energized, the rear intermittent wiper relay contacts open; however, the cam contacts keep the rear wiper motor energized until the wiper blades return to their stop position Washer-wiper operation When the rear washer switch is turned "ACC" or "ON" position, current flows through multi-purpose fuse number 8 remote-controlled mirror switch, remote-control mirror, remote-controlled mirror switch, and ground, causing the mirror to move
5-0 REAR WIPER AND WASHER REMOVAL AND INSTALLATION REAR WIPER AND WASHER M5008800067 7 6 5 4 75 N m 66 in-lb 6 49 N m 4 in-lb 9 8 AC00898AB REAR INTERMITTENT WIPER RELAY REAR WIPER MOTOR ASSEMBLY REMOVAL STEPS >>B<< REAR WIPER ARM AND BLADE ASSEMBLY >>A<< GROMMET LIFTGATE GARNISH (REFER TO P5-6) 4 GROMMET 5 REAR WIPER MOTOR ASSEMBLY REAR WASHER HOSE REMOVAL STEPS QUARTER TRIM, LOWER <RH> (REFER TO GROUP 5A, TRIMS P5A-6) 6 REAR WASHER HOSE 7 WASHER NOZZLE REAR WASHER TANK ASSEMBLY AND REAR WASHER MOTOR REMOVAL STEPS QUARTER TRIM, LOWER <RH> (REFER TO GROUP 5A, TRIMS P5A-6) WASHER FLUID DRAINING 6 REAR WASHER HOSE 8 REAR WASHER TANK 9 REAR WASHER MOTOR NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 54A, Column switch P7A-
5- REAR WIPER AND WASHER INSTALLATION SERVICE POINTS >>A<< GROMMET INSTALLATION Install the grommet so that the arrow points downwards GROMMET ARROW AC009AB CERAMIC SECTION >>B<< REAR WIPER ARM AND BLADE ASSEMBLY INSTALLATION Install the wiper blade so that the tip stops at the standard position (standard value), and also so that the lower section of the wiper blade enters the middle of the defogger pattern Standard value: 70 ± 5 mm (8 ± 0 inches) DEFOGGER PATTERN Y04AA AC009AB INSPECTION M50086005 REAR WIPER AND WASHER SWITCH CHECK Follow the table below to check the rear wiper and washer switch for continuity AC0090 SWITCH POSITION Windshield intermittent wiper switch ON TERMINAL CONNECTION SPECIFIED CONDITION 0 Less than ohms Rear wiper switch ON 4 0 Less than ohms Rear washer switch ON 0 Less than ohms
5- REAR WIPER AND WASHER REAR WIPER MOTOR CHECK Check the wiper motor after first disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body Wiper Motor Operation Connect a battery to the wiper motor as shown in the illustration and inspect the motor operation OPERATION CHECK Wiper Motor at Stop Position Operation Run the wiper motor, disconnect the battery, and stop the motor Reconnect the battery as shown in the illustration, and confirm that after the motor starts turning it stops at the automatic stop position STOP POSITION CHECK AC009AB REAR INTERMITTENT WIPER RELAY CHECK Check that there is continuity between terminals () and () Connect terminals (4), (5) to the battery (+) terminal Check that there is battery voltage at terminal () for intermittent periods of eight seconds when terminal (7) is connected to the battery (-) terminal REAR INTERMITTENT WIPER RELAY AC0095 AB REAR WASHER MOTOR CHECK With the washer motor installed to the washer tank, fill the washer tank with water When the battery is connected as shown in the figure, check that the washer squirts out strongly AC0096
B C A C A D 5- MARK REAR WASHER FLUID EJECTION CHECK Move the nozzle to adjust so that the water is sprayed out within the range shown in the illustration A: 55 mm (6 inches), B: 8 mm (49 inches), C: 0 mm (078 inches), D: 07 mm (8 inches) CERAMIC LINE Y06AA AC00468AB REMOVAL AND INSTALLATION MARK M5080086 6 5 4 7 AC00769 AD >>A<< "MONTERO SPORT" MARK >>A<< "MONTERO SPORT" MARK >>A<< "AWD" DECAL >>A<< 4 "GRADE" MARK >>A<< 5 "UNLOCK" MARK >>A<< 6 "-DIAMOND" MARK >>A<< 7 "MITSUBISHI" MARK
5-4 MARK INSTALLATION SERVICE POINT >>A<< MARK INSTALLATION Installation position Attach to the position shown in the illustration "MONTERO SPORT" MARK ALIGN TO PRESS LINE FENDER PANEL END LINE LIFTGATE GARNISH END LINE ALIGN TO NOTCH LIFTGATE GARNISH END LINE "GRADE" MARK "AWD" DECAL, "GRADE" MARK LIFTGATE GARNISH END LINE ALIGN TO PRESS LINE LIFTGATE END LINE LIFTGATE GARNISH END LINE AC0787 "-DIAMOND" MARK LIFTGATE GARNISH CENTER LINE LIFTGATE GARNISH END LINE "UNLOCK" MARK KEY CYLINDER LINE 48 mm (058 in) LIFTGATE GARNISH END LINE LIFTGATE GARNISH END LINE LIFTGATE PRESS LINE AC00768 AC0788AC
5-5 DOOR MIRROR MITSUBISHI MARK LIFTGATE GARNISH CENTER LINE NOTCH ALIGN TO LOWER END OF LIFTGATE GARNISH AC00986AB Installation procedure () Use M AAD Part number 8906 or equivalent to clean the mark installation surfaces on the body CAUTION When attaching the marks, the surrounding temperature should be 0 8 C (60 00 F) and the air should be completely free from dust If the surrounding temperature is low than 0 C (60 F), the marks and their application surface on the body should be heated to 0 8 C (60 00 F) () Peel off the backing paper from the reverse side of the marks, carefully attach the marks to the vehicle body in the exact position shown SPECIAL TOOL TOOL TOOL NUMBER AND NAME MB990784 Ornament remover DOOR MIRROR SUPERSESSION General service tool APPLICATION M500060075 Removal of remote controlled mirror switch MB990784
5-6 DOOR MIRROR REMOVAL AND INSTALLATION DOOR MIRROR M500640048 4 5 AC00987AB ADHESIVE TAPE: DOUBLE-SIDED TAPE 5 mm (0 in) WIDTH AND 04 mm (00 in) THICKNESS REMOTE CONTROLLED MIRROR SWITCH DOOR MIRROR REMOVAL STEPS DELTA COVER, INNER HARNESS CONNECTOR <VEHICLES WITH REMOTE CONTROLLED MIRROR> 4 MIRROR ASSEMBLY <<A>> 5 MIRROR REMOVAL SERVICE POINT CLAWS <<A>> MIRROR REMOVAL Tilt the mirror upward by hand, insert a flat-tipped screwdriver onto which protective tape has been wound, and then pry the claws off of the actuator AC00988AB
5-7 DOOR MIRROR Pull the mirror downward to remove it from the claws CLAWS AC00989AB AC00990 INSPECTION M500650090 ELECTRIC REMOTE CONTROL MIRROR OPERATION CHECK Follow the table below to check the electric remote control mirror operation <VEHICLES WITHOUT HEATED MIRROR> Check that the mirror moves as described in the table when each terminal is connected to the battery BATTERY CONNECTION Connect terminal to the positive Connect terminal to the negative Connect terminal to the positive Connect terminal to the negative Connect terminal to the positive Connect terminal to the negative Connect terminal to the positive Connect terminal to the negative MIRROR GLASS: Tilts up Tilts down Turns to the right Turns to the left <VEHICLES WITH HEATED MIRROR> Check that the mirror moves as described in the table when each terminal is connected to the battery AC0099
5-8 DOOR MIRROR BATTERY CONNECTION Connect terminal 7 to the positive Connect terminal 5 to the negative Connect terminal 5 to the positive Connect terminal 7 to the negative Connect terminal 6 to the positive Connect terminal 5 to the negative Connect terminal 5 to the positive Connect terminal 6 to the negative MIRROR GLASS: Tilts up Tilts down Turns to the right Turns to the left HEATED MIRROR OPERATION CHECK Ensure that there is continuity between terminal and terminal 4 of the door mirror connector AC0099 DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK Follow the table below to check the door mirror control switch for continuity SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION 5 6 7 8 4 9 Left side Up 4 8, 6 7 Less than ohms Down 4 7, 6 8 Less than ohms Right 6, 4 7 Less than ohms Left 4, 6 7 Less than ohms AC0068 Right side Up 4, 6 7 Less than ohms Down 6, 4 7 Less than ohms Right 4 7, 6 9 Less than ohms Left 4 9, 6 7 Less than ohms
SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS ITEM Front bumper Fog light bracket screw Fog light screw Lift gate garnish Lift gate garnish nut Rear wiper and washer Wiper arm and blade assembly nut Wiper motor Side step Side step pipe assembly Under floor spare tire carrier Spare tire carrier bolt Windshield wiper and washer Washer tank bolt Wiper arm and blade assembly nut Wiper link assembly nut Wiper motor bolt 5-9 SPECIFICATIONS SPECIFICATION 07 N m (6 in-lb) 5 N m ( in-lb) 49 N m (4 in-lb) 75 N m (65 in-lb) 49 N m (4 in-lb) N m (98 in-lb) N m (04 in-lb) 49 N m (4 in-lb) N m ( in-lb) 49 N m (4 in-lb) 49 N m (4 in-lb) M505008 SERVICE SPECIFICATIONS ITEM STANDARD VALUE Windshield wiper blade position Driver's side 6 ± 5 (0 ± 0) installation mm (in) Passenger's side 0 40 ( 5) Rear wiper blade position installation mm (in) 70 ± 5 (8 ± 0) M50000087 SEALANTS AND ADHESIVES ITEM Door molding Side step molding Delta cover inner M500050070 SPECIFICATION Adhesive tape: Double-sided tape, <A, C, E [ mm (005 in) thickness], B [5 mm (0 in) width and mm (005 in) thickness], D [ mm (05 in) width and mm (005 in) thickness]> Adhesive tape: Double-sided tape [ mm (09 in) wide and 08 mm (00 in) thickness] Adhesive tape: Double-sided tape [5 mm (0 in) width and 04 mm (00 in) thickness]
NOTES