THE WALL-MOUNT AIR CONDITIONERS - WA (60HZ)

THE WLL-MOUNT IR CONDITIONERS - W (HZ) W-SERIES Hz. to Ton (,3 to 7, Btuh) Right Side Control Panel Refrigerant The Bard Wall-Mount ir Conditioner is a self contained energy efficient system, which is designed to offer maximum indoor comfort at a minimal cost without using valuable indoor floor space or outside ground space. This unit is the ideal product for versatile applications such as: new construction, modular offices, school modernization, telecommunication structures, portable structures or correctional facilities. Factory or field installed accessories are available to meet specific job requirements. Engineered Features luminum Finned Copper Coils: Grooved tubing and enhanced louvered fin for maximum heat transfer and energy efficiency. Twin Blowers: Move air quietly. Most models feature multispeed blower motors providing airflow adjustment for high and low static operation. Motor overload protection is standard on all models. ir Conditioner Compressor: Reciprocating compressors with crankcase heater and discharge muffler are standard on. and ton models. Compressors eliminate need for crankcase heater. Standard on. to ton, and available on ton models. Phase Rotation Monitor: Standard on all 3 phase scroll compressors. Protects against reverse rotation if power supply is not properly connected. Not required on reciprocating compressors. Galvanized Gauge Zinc Coated Steel Cabinet: Cleaned, rinsed, sealed and dried before the polyurethane primer is applied. The cabinet is handsomely finished with a baked on textured enamel, which allows it to withstand hours of salt spray tests per STM B7-3. Electrical Components: re easily accessible for routine inspection and maintenance through a right side, service panel opening. Features a lockable, hinged access cover to the circuit breaker or pull disconnect switch. Electric Heat Strips: Features an automatic limit and thermal cut-off safety control. Heater packages can be factory or field installed for all. through ton models. One Inch, Disposable ir Filters: re standard equipment. Optional one inch washable filters available and filter racks permit the addition of " pleated filter. Factory or field installed. Condenser Fan and Motor Shroud ssembly: Slides out for easy access. Barometric Fresh ir Damper: Standard on all units. llows up to % outside fresh air. Built-in Circuit Breakers: Standard on all electric heat versions of single (3/ volt) and three phase (3/ volt) equipment. Toggle disconnects are standard on all electric heat versions of three phase (4 volt) equipment. Slope Top: Standard feature for water run-off. Full Length Mounting Brackets: Built into cabinet for improved appearance and easy installation. NOTE: Bottom mounting bracket included to assist in installation. Top Rain Flashing: Standard feature on all models. Ventilation System Packages ll packages are designed to meet your specific ventilation requirements utilizing one of five ventilation options for the product. The ventilation package is mounted within the unit eliminating the need for an exterior mounted hood or damper assembly on the unit. ll assemblies can be factory installed, installed in the field at time of installation or as a retrofit system after installation. ME # 7-3-E Standard - Barometric Fresh ir Damper Optional - Motorized Fresh ir Damper Optional - Blank off Plate Optional - Commercial Room Ventilator w/exhaust CRV - Spring Return CRVP - Power Return Optional - Economizer w/ Exhaust Optional - Energy Recovery Ventilator Complies with efficiency requirements of NSI/SHRE/IESN.-7. Certified to NSI/RI Standard 3-3 for SPVU (Single Package Vertical Units). Commercial Product - Not intended for Residential application. Form No. S3- Supersedes S3- Page of

Capacity and Efficiency Ratings MODELS W W4 W3 W3 W3 W43 W44 W W Capacity BTUH,3 3,4 3, 3, 3, 4, 47, 7,, EER....3....7. SEER 3......... Capacity is certified in accordance with NSI/RI Standard 3-3 and tested in accordance with RI Standard /4-. EER = Energy Efficiency Ratio and is certified in accordance with NSI/RI Standard 3-3. 3 SEER = Seasonal Energy Efficiency Ratio and is tested in accordance with RI Standard /4-. ll ratings based on fresh air intake being % closed (no outside air introduction). Specifications -/ Ton through 3 Ton MODELS W- W4- W4-B W4-C W3- W3-B W3- W3-B W3-C W3- W3-B Electrical Rating-- Hz 3/ - 3/ - 3/ - 3 4-3 3/ - 3/ - 3 3/ - 3/ - 3 4-3 3/ - 3/ - 3 4-3 Operating Voltage Range 7-3 7-3 7-3 44-7-3 7-3 7-3 7-3 44-7-3 7-3 44- Compressor--Circuit Voltage 3/ 3/ 3/ 4 3/ 3/ 3/ 3/ 4 3/ 3/ 4 Rated Load mps 7./../../. 3../../7../..4/. 4 4../7. 3./.. Branch Circuit Selection Current.. 7. 4.. 3 7. 4.. 4. 7. 3.. Lock Rotor mps 4/4 / / 4/4 / 73/73 3/3 3 / 77/77 37 C ompressor Type R ecip. R ecip. R ecip. Recip. Fan Motor & Condenser Fan Motor--HP--RPM / - / - / - / - / - / - / - / - / - / - / - / - Fan Motor--mps.... 4..... 4... 4 Fan--DI/CFM " - " - " - " - " - " - " - " - " - " - " - " - Blower Motor & Evap. W3-C Blower Motor--HP-RPM-SPD /-- /-- /-- /3-- /-- /-- /3-- /3-- /3-- /3-- /3-- /3-- Blower Motor--mps............ CFM & E.S.P. w/filter (Rated-Wet Coil) -.4 -. -. -. -. -. -.4 -.4 -.4 -.3 -.3 -.3 Filter Sizes (inches). xx xx xx xx xx xx x3x x3x x3x x3x x3x x3x Shipping Weight --LBS. 3 3 3 3 3 3 Specifications 3-/ Ton through Ton MODELS W43- W43-B W43-C W44- W44-B W44-C W- W-B W-C W- W-B Operating Voltage Range 7-3 7-3 44-7-3 7-3 44-7-3 7-3 44-7-3 7-3 44- Compressor--Circuit Voltage 3/ 3/ 4 3/ 3/ 4 3/ 3/ 4 3/ 3/ 4 Rated Load mps.3/./.../../. 3../../. 4../../. 7 7. Branch Circuit Selection Current........... Lock Rotor mps 7/7 / 4 3/3 / 4 4/4 37/37 4/4 3/3 Compressor Type Fan Motor & Condenser Fan Motor--mps... 3... 3... 3 4. 4.. 7 Fan--DI/CFM - - - - - - - - - - - - Blower Motor & Evap. W-C Electrical Rating-- Hz 3/- 3/-3 4-3 3/- 3/-3 4-3 3/- 3/-3 4-3 3/- 3/-3 4-3 Fan Motor--HP-RPM-SPD /3-- /3-- /3-- /3-- /3-- /3-- /3-- /3-- /3-- /3-- /3-- /3-- Blower Motor--HP-RPM-SPD /-7- /-7- /-7- /-7- /-7- /-7- /-7- /-7- /-7- /-7- /-7- /-7- Blower Motor--mps 3. 3 3. 3. 3. 3 3. 3. 3. 3 3. 3. 3. 3 3. 3. CFM & E.S.P. w/filter (Rated-Wet Coil) 4 -.3 4 -.3 4 -.3 -. -. -. 7 -.3 7 -.3 7 -.3 7 -.3 7 -.3 7 -.3 Filter Sizes (inches). x3x x3x x3x x3x x3x x3x x3x x3x x3x x3x x3x x3x Shipping Weight --LBS. Form No. S3- Supersedes S3- Page of

Ventilation System Packages Bard Wall-Mounts are designed to provide optional ventilation packages to meet all of your ventilation and indoor air quality requirements. ll units are equipped with a barometric fresh air damper as the standard ventilation package. ll ventilation packages can be built-in at the factory or field-installed at a later date. BROMETRIC FRESH IR DMPER - BFD STNDRD The barometric fresh air damper is a standard feature on all models. It is installed on the inside of the service door and allows outside ventilation air, up to % of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The damper opens during blower operation and closes when the blower is off. djustable blade stops allow different amounts of outside air to be introduced into the building and can be easily locked closed if required. Barometric Fresh ir Damper Motorized Fresh ir Damper BLNK OFF PLTE - BOP OPTIONL blank off plate is installed on the inside of the service door. It covers the air inlet openings, which restricts any outside air from entering the unit. The blank off plate should be utilized in applications where outside air is not required to be mixed with the conditioned air. MOTORIZED FRESH IR DMPER - MFD OPTIONL The motorized fresh air damper is internally mounted behind the service door and allows outside ventilation air, up to % of the total airflow rating of the unit, to be introduced through the air inlet openings and to be mixed with the conditioned air. The two position damper can be fully open or closed. The damper blade is powered open by a 4VC motor with spring return on power loss. The damper can be controlled by indoor blower operation or can be field connected to be managed based on building occupancy. NOTE: The above vent systems are intake only without built-in exhaust capability. Building will likely require separate field installed barometric relief or mechanical exhaust elsewhere within the conditioned space. Balancing dampers in the return air grille may be required to achieve specified amount of outdoor air intake. COMMERCIL ROOM VENTILTOR - CRV OPTIONL The built-in commercial room ventilator is internally mounted behind the service door and allows outside ventilation air, up to % of the total airflow rating of the unit, to be introduced through the air inlet openings. It includes a built-in exhaust air damper. Commercial Room Ventilator The commercial room ventilator (CRV) is a simple and innovative approach to improving the indoor air quality by providing fresh air intake and exhaust capability through the CRV. The damper can be easily adjusted to control the amount of fresh air supplied into the building. The CRV can be controlled by indoor blower operation or field controlled based on room occupancy. Two versions available (except on. and -Ton models). The CRV and CRVS are power open - spring return on power loss, and CRVP is power open and power close. Complies with NSI/SHRE Standard. Ventilation for cceptable Indoor ir Quality. ECONOMIZER - EIFM OPTIONL The built-in economizer system is internally mounted behind the service door and allows outdoor air to be introduced through the air inlet openings. The amount of outdoor air varies in response to the system controls and settings defined by the end user. It includes a built-in exhaust air damper. The economizer is designed to provide free cooling when outside air conditions are cool and dry enough to satisfy cooling requirements without running the compressor. This in turn provides lower operating costs, while extending the life of the compressor. Economizer Energy Recovery Ventilator Standard Features: One Piece Construction - Easy to install with no mechanical linkage adjustment required. Exhaust ir Damper - Built in with positive closed position. Provides exhaust air capability to prevent pressurization of tight buildings. ctuator Motor - 4 volt, power open, spring return with built in torque limiting switch. Proportioning Type Control - for maximum free cooling economy and comfort. Moisture Eliminator & Prefilter - permanent, washable aluminum construction. Enthalpy Control - adjustable to monitor outdoor temperature and humidity. Minimum Position Potentiometer - adjustable to control minimum damper blade position for ventilation purposes. Mixed ir Sensor - to monitor outside and return air to automatically modulate damper position. WLL-MOUNT ENERGY RECOVERY VENTILTOR - WERV OPTIONL The wall-mount energy recovery ventilator (WERV) is a highly innovative approach to meeting indoor air quality ventilation requirements as established by NSI/SHRE Standard.. The WERV allows from to CFM (depending upon model) of fresh air and exhaust through the unit while maintaining superior indoor comfort and humidity levels. In most cases this can be accomplished without increasing equipment sizing or operating costs. Heat transfer efficiency is up to 7% during summer and % during winter conditions. The WERV consists of a unique rotary energy recovery cassette that provides effective sensible and latent heat transfer capabilities during summer and winter conditions. Various control schemes are addressed including limiting ventilation during building occupancy only. The WERV is designed to be internally mounted behind the service door in the W, WH or WL model wall-mount units. It can be built-in at the factory or field installed as an option. WERV-*3C and WERV-*C can be independently adjusted for intake and exhaust rates. Manufactured under U.S. Patent Nos.,,7;,3,744;,,; 4,4,34; 4,,; 4,,3;,3,33. Form No. S3- Supersedes S3- Page 3 of

7 4 3 Commercial Room Ventilator Performance Data - CRV- W, W4 & W TOTL ND VENTILTION IRFLOW ir ESP ir. ESP ir.3 ESP Vent ir ESP Vent ir. ESP Vent ir.3 ESP B C D E F Commercial Room Ventilator Performance Data - CRVS-3 and CRVP-3 W3 & W37 HIGH SPEED TOTL ND VENTILTION IRFLOW W3 & W37 LOW SPEED TOTL ND VENTILTION IRFLOW 7 ir ESP ir. ESP ir.3 ESP Vent ir ESP Vent ir. ESP Vent ir.3 ESP 7 4 ir ESP ir. ESP ir.3 ESP Vent ir ESP Vent ir. ESP Vent ir.3 ESP 4 3 3 B C D E F B C D E F irflow (cfm) irflow (cfm) Form No. S3- Supersedes S3- Page 4 of irflow (cfm)

Commercial Room Ventilator Performance Data - CRVS- and CRVP- Commercial Room Ventilator Performance Data - CRVS- and CRVP- 7 4 3 7 4 3 W4 & W4 HIGH SPEED TOTL ND VENTILTION IRFLOW irflow (cfm) B C D E F ir ESP ir. ESP ir.4 ESP Vent ir ESP Vent ir. ESP Vent ir.4 ESP 7 4 3 7 4 3 W HIGH SPEED TOTL ND VENTILTION IRFLOW B C D E F ir ESP ir. ESP ir.4 ESP Vent ir ESP Vent ir. ESP Vent ir.4 ESP W4 & W4 LOW SPEED TOTL ND VENTILTION IRFLOW W LOW SPEED TOTL ND VENTILTION IRFLOW 7 4 3 7 irflow (cfm) irflow (cfm) 4 3 4 3 ir ESP ir. ESP ir.4 ESP Vent ir ESP Vent ir. ESP Vent ir.4 ESP 7 4 3 ir ESP ir. ESP ir.4 ESP Vent ir ESP Vent ir. ESP Vent ir.4 ESP irflow (cfm) B C D E F B C D E F Form No. S3- Supersedes S3- Page of

Performance and pplication Data- WERV-*B mbient O.D. DB/ WB F VLT VENTILTION RTE -- % EFFICIENCY VLS VLL HRT CFM HRS HRL SUMMER COOLING PERFORMNCE (INDOOR DESIGN CONDITIONS DB/ WB) VLT VENTILTION RTE -- 3% EFFICIENCY VLS VLL HRT CFM HRS HRL VLT VENTILTION RTE -- 3% EFFICIENCY 3 734 7 7 344 4 4 3 4 7 7 7 4 4 4 4 7 7 4 4 4 4 7 7 4 3 44 4 4 34 443 734 3 7 3 33 4 4 44 34 7 3 3 4 7 73 3 3 4 4 4 3 34 3 3 4 4 34 34 3 3 4 4 34 34 4 334 33 7 3 4 3 44 43 4 4 734 334 44 7 7 3 3 4 43 3 7 3 4 43 4 334 7 73 3 3 4 43 7 3 737 4 4 334 334 3 3 43 43 4 4 334 334 3 3 43 43 37 7 343 4 44 34 4 4 7 734 43 7 343 74 443 4 34 3 4 3 7 3 3 4 744 73 343 3 3 4 4 34 3 4 47 343 343 34 34 4 4 343 343 34 34 4 4 7 74 7 7 4 3 4 3 4 44 3 744 7 734 74 7 4 3 4 73 3 44 7 3 7 43 4 74 73 4 3744 3 3 4 33 3 3 7 7 74 74 4 4 3 3 3 3 7 7 74 74 4 4 3 3 3 3 734 37 7 7 4 3 3 4 4 33 7 3 3 4 37 34 73 4 4 3 34 4 44 3 77 33 3 37 4 33 47 37 37 4 4 7 3 3 4 4 73 73 3 4 4 3 3 33 33 33 33 VLS VLL HRT CFM HRS HRL WERV-*B WINTER HETING PERFORMNCE (INDOOR DESIGN CONDITIONS 7 F DB) VENTILTION RTE mbient O.D. CFM 74% EFF. CFM % EFF. CFM % EFF. DB/ F WVL WHR WVL WHR WVL WHR 4 7 4 7 343 733 34 43 4 3 343 43 34 4 4 4 4 4 7 4 4 3 37 7 3 7 7 7 4 4 3 3 NOTE: performance only is shown for winter application. LEGEND: VLT = Ventilation Load - VLS = Ventilation Load - VLL = Ventilation Load - Latent HRT = Heat Recovery - HRS = Heat Recovery - HRL = Heat Recovery - Latent WVL = Winter Ventilation Load WHR = Winter Heat Recovery Form No. S3- Supersedes S3- Page of

Performance and pplication Data- WERV-*C Performance and pplication Data- WERV-*3C SUMMER COOLING PERFORMNCE (INDOOR DESIGN CONDITIONS DB/ WB) SUMMER COOLING PERFORMNCE (INDOOR DESIGN CONDITIONS DB/ WB) V ENTILTION RTE CFM V ENTILTION RTE 3 CF M VENTILTION RTE 3 CF M mbient O.D. CFM VENTILTION RTE -- % EFFICIENCY CFM 3 VENTILTION RTE -- 4% EFFICIENCY 4CFM VENTILTION RTE -- 3% EFFICIENCY mbient O.D. DB/ W B F V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S HR L DB/ W B F V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S H R L V L T V L S V L L H R T H R S HR L 4 4 3 47 7 447 7 7 73 7 37 43 7 37 4 3 47 73 3 3 7 4 7 47 7 47 7 7 4 4 3 3 73 73 4 4 3 3 73 73 47 7 47 7 3 44 3 3 7 7 3 3 737 4 4 4 7 3 7 4 3 4 3 7 7 4 7 7 7 7 3 43 7 4 7 4 7 7 7 3 3 7 3 3 3 7 4 7 7 4 77 44 4 4 7 4 3 7 7 7 4 77 7 4 3 7 7 4 3 7 33 3 7 7 7 4 3 77 4 7 3 4 4 4 3 7 7 3 4 4 77 77 4 3 7 4 3 7 4 4 77 77 4 3 7 4 3 7 7 7 7 7 4 7 4 7 7 7 7 7 4 7 4 7 4 44 7 44 3 4 7 7 4 44 4 4 7 7 7 7 3 3 3 4 3 737 4 34 4 4 434 7 4 44 44 3 7 7 4 44 4 4 7 44 4 74 4 3 3 73 4 7 7 7 7 34 43 4 73 7 434 4 7 4 34 7 44 3 47 4 7 44 4 4 44 7 3 3 7 3 3 7 3 34 44 7 3 4 7 434 7 4 4 44 3 44 3 44 44 4 4 3 3 34 34 4 4 434 434 4 4 44 3 44 3 44 44 4 4 3 3 34 34 4 4 434 434 3 7 43 3 3 4 73 7 4 3 7 737 4 4 33 4 4 3 4 4 7 4 3 4 3 3 3 4 4 7 3 77 4 7 4 7 47 3 4 73 3 7 7 7 4 7 7 43 4 7 3 33 7 4 4 7 3 3 7 3 3 4 7 7 7 3 7 7 4 73 3 3 7 4 7 3 4 7 4 3 4 3 37 7 3 7 4 4 7 4 3 3 7 3 3 34 4 4 4 3 7 7 4 73 4 73 7 7 4 4 4 4 3 3 4 4 4 4 3 3 3 3 4 4 3 3 7 7 4 73 4 73 7 7 4 4 4 4 3 3 4 4 4 4 3 3 3 3 4 4 3 3 4 73 3 3 737 4 3 7 737 4 7 47 34 4 7 3 43 37 7 4 3 4 4 7 4 7 4 4 3 7 3 7 7 33 7 7 3 43 34 7 7 7 74 43 47 4 77 7 7 7 4 74 47 3 4 3 7 3 7 4 3 34 4 7 7 334 7 43 7 4 4 7 4 34 3 7 4 44 7 4 4 7 7 34 34 7 7 43 43 4 4 7 7 4 4 7 7 34 34 7 7 43 43 4 4 7 7 7 4 43 3 3 7 37 7 7 33 4 43 7 7 3 374 7 3 7 7 7 7 7 7 3 7 43 7 44 3 7 3 33 7 3 7 443 7 7 3 7 7 3 4 4 4 7 7 3 4 43 7 4 7 4 3 4 3 33 33 3 4 3 7 3 3 3 7 3 3 4 3 3 7 7 43 43 7 7 33 33 3 3 3 3 7 7 7 7 7 3 3 7 3 7 3 3 3 7 7 7 7 7 7 7 44 44 4 4 7 4 7 4 4 3 4 3 33 33 3 3 37 37 3 3 37 37 3 3 3 3 WERV-*C WINTER HETING PERFORMNCE (INDOOR DESIGN CONDITIONS 7 F DB) WERV-*3C WINTER HETING PERFORMNCE (INDOOR DESIGN CONDITIONS 7 F DB) VENTILTION RTE 4 CFM 3 CF M 3 CF M mbient O.D. LEGEND: CFM 77% EFF. VENTILTION RTE 3 CFM 7% EFF. 4 CFM % EFF. mbient O.D. D B/ F W V L W H R W V L W H R W V L WH R VLT = Ventilation Load - VLS = Ventilation Load - VLL = Ventilation Load - Latent HRT = Heat Recovery - HRS = Heat Recovery - HRL = Heat Recovery - Latent WVL = Winter Ventilation Load WHR = Winter Heat Recovery D B/ F W V L W H R W V L W H R W V L WH R 43 4 4 4 3 4 3 3 34 3 7 4 4 3 777 4 3 3 4 4 4 4 77 7 3 47 4 34 3 44 3 7 7 74 47 43 44 4 3 4 33 3 3 43 34 7 7 7 4 4 4 3 4 4 33 4 77 7 4 3 3 7 34 33 7 3 44 7 3 44 7 4 333 3 73 3 4 7 4 4 37 3 47 43 4 application. winter for shown is only performance NOTE: application. winter for shown is only performance NOTE: Form No. S3- Supersedes S3- Page 7 of

Electrical Specifications Single Circuit Dual Circuit Model Rated Volts and Phase No. Field Power Circuits 3 Minimum Circuit mpacity Maximum External Fuse or Brkr. Field Power Wire Size Ground Wire 3 Minimum Circuit mpacity B Maximum External Fuse or Brkr. B Field Power Wire Size B Ground Wire Size B W -, Z 3/- 3 3 W4 -, Z 3/- 7 3 3 W4 - B, BZ B 3/-3 3 4 W4 - C, CZ C 4-3 4 4 4 4 W3 -, Z 3/- 3 3 W3 - B, BZ B 3/-3 4 W3 - *, Z* * * 3/- or 4 3 47 7 3 4 7 3 W3 - B*, BZ* B B* B 3/-3 7 3 3 W3 - C*, CZ* C C* C 4-3 7 3 4 4 4 4 W3 - *, Z* * * 3/- or 3 47 4 4 7 3 W3 - B*, BZ* B B* B 3/-3 4 33 W3 - C*, CZ* C C* C 4-3 7 3 4 4 4 4 W43 -, Z 3/- or or 4 3 W43 - B, BZ B B B 3/-3 4 34 W43 - C, CZ C C 4-3 3 7 3 4 4 W44 -, Z 3/- or or 3 3 4 3 W44 - B, BZ B B B 3/-3 34 W44 - C, CZ C C 4-3 3 7 3 4 4 W -, Z 3/- or or 44 44 4 3 W - B, BZ B B B 3/-3 3 34 W - C, CZ C C 4-3 7 3 W -, Z 3/- or or 4 4 4 3 W - B, BZ B B B 3/-3 3 34 W - C, CZ C C 4-3 7 3 Maximum size of the time delay fuse or HCR type circuit breaker for protection of field wiring conductors. Based on C copper wire. ll wiring must conform to the National Electrical Code and all local codes. 3 These Minimum Circuit mpacity values are to be used for sizing the field power conductors. Refer to the National Electrical code (latest version), rticle 3 for power conductor sizing. Caution: When more than one field power circuit is run through one conduit, the conductors must be derated. Pay special attention to note of Table 3 regarding mpacity djustment Factors when more than three (3) current carrying conductors are in a raceway. * Top outlet supply option is available only factory installed and only on the selected models. IMPORTNT: While this electrical data is presented as a guide, it is important to electrically connect properly sized fuses & conductor wires in accordance with the National Electrical Code and all local codes. Form No. S3- Supersedes S3- Page of

Indoor Blower Performance - CFM at 3 or 4 Volts ESP in H O W W4 W3 High Speed W3 W3 Low Speed High Speed W43 W44 Low Speed High Speed W W Low Speed / 3/ / / / / /. / 34/7 3/ 77/ / / /3. / / / / /4 / /. 3 /7 / /3 /4 /3 /7 -/-. 4 7/ / / 37/ 3/ 7/ -/-. / /7 -/- / -/- /4 -/- bove data is with " standard throwaway filter and " washable filter. For optional " pleated filter - reduce ESP by. in. See installation instructions for maximum ESP information on various KW application. Electric Heat Table - Refer to Electrical Specifications for vailability by Unit Model Nominal KW Kw t 4V () t V () t 4V () t 4V () -Ph mps 3-Ph mps Btuh Kw -Ph mps 3-Ph mps Btuh... 7, 3..,7 Kw 3-Ph mps Btuh Kw 3-Ph mps Btuh.. 4. 4,47 4..,. 7.,47..,4.. 33. 3 7,34..,47... 7 3,77.. 7 3,3.. 3,77.. 4,.. 4. 7 34,3 7. 3.,... 3.,. 4. 3. 3,3.., 3. 7. 3 47,.. 43. 3,434 3. 37. 4,7.. 7,434..,.. 3. 3,.., () These electric heaters are available in 3/V units only. () These electric heaters are available in 4V units only. Heater Packages - Field Installed Designed for adding Electric Heat to KW Units Circuit Breaker Standard on 3/V Models Toggle Disconnect Standard on 4V Models - Models ir Conditioner 3/- Models Heater Model # EHW- W EHW- EHW- EHW- W4 EHW- W3 EHW- EHW3- EHW3- W3 EHW3- EHW3- EHW3- EHW3- W3 EHW3- EHW3- W43 W44 EHW- EHW- EHW- EHW- UL Listed CUL Listed -B Models 3/-3 K W Heater Model # -C Models 4-3 K W Heater Model # N/ KW EHW4-B EHWH4B-C EHW3-B EHW3-B EHW3-B EHW3-B EHW3-B EHW37-B EHW-B EHW-B EHW-B EHW- EHW-B W EHW- EHW-B W EHW- EHW-B EHW- NOTE: Field installed Heater Packages are not approved for use with top supply opening models. Model W4 only. EHWC3-C EHWC3-C EHW3-C EHWC3-C EHWC3-C EHW3-C EHW-C EHW-C EHW-C EHW-C Form No. S3- Supersedes S3- Page of

Form No. S3- Supersedes S3- Page of pplication Data - Outdoor Temperature Below o F (.3C), unit requires a factory or field installed low ambient control. Return air temperature. Model D.B./W.B. Capacity 7 o F o F o F o F o F o F o F o F o F o F o F W /, 4,, 4,7 7,7 4,4, 4,, 3,3, 3,3 4,, 3,3,3,,4,7,7,, / 7, 4,,3 4,,7 4,3, 4,,3 3,7 7,4 3,4, 3,3,,,, 4,4, 3,, / 4, 4, 3,7 4,, 4,4,4 4,, 3,, 3,,,,3,3,, 4,7,4 3,, W4 / 4,, 3,3,3,3,,4 7,,4 7,,,,, 7,, 7, 4,4,3 3,4,, / 7, 7,,3 7, 4,7 7, 4, 7, 3,4 7,,,,,,3,, 4,,7 4,, 3, / 3,,4,,,4 7, 7, 7,4,,,,3 3,,,7 4,7, 3,,,7,, W3 / 3,4,,,7,,4, 7,, 7,, 7,,3, 7,4,,4,,4, 4,3 4, / 7 4,, 4,,3 4,, 3,7 7, 3, 7,7,3 7,4, 7,,7,7,7,,, 7,4,3 /,7,,, 7,,3, 7,, 7,4 4,4, 3,,,,7,7,,4 4,3 7, 3, W3 / 3,,7,7,3, 4, 7,4 4,4, 3,, 3,3 4,,7,,,,,,,7, / 7 33, 4, 3,3 4, 3, 4, 3, 4,4 3, 4,, 3,7,3 3,3 7,3,,3,3,,7 4,, / 3,3, 37,, 3,3 4,7 34, 4,3 33,4 3,7 3, 3, 3,,,, 7,7,,, 4,7,7 W3 / 37,3,,7 7,7 34, 7,3 3,, 3,4,4 3,,,, 7, 4,,7 3,,7, 4,, / 7 3, 7, 3, 7, 3, 7, 37,, 3,,,, 34,, 33,,3 3, 4,7 3, 4, 3, 3, / 47,4 7,, 7, 43,7 7, 4,, 4,, 3,4,4 3, 4,, 3,7 33,, 3,3,7 3,, W43 / 43,, 4,7 34,3 4, 33, 3,4 3, 3, 3, 34, 3, 33, 3, 3,,3,,3, 7, 4,7, / 7 4, 33,,4 33, 44, 33, 43,4 3, 4, 3,3 4, 3,7 3, 3, 37, 3,3 34,,4 3,, 3, 7, / 4, 34,7 3, 34,, 33,4 4, 3, 4,7 3,7 44,3 3,7 4,, 3,4,4 3,7 7, 33,, 3, 4,4 W44 / 4, 3, 4,3 3, 44, 37, 43,7 37, 4,3 37, 3,34 3,3 37, 34, 34,4 33,33 3,3 3,4 3, 3,,,7 / 7,44 37,,44 37, 4,4 37, 4, 37,4 47, 37,3, 3,74 43,, 4, 34,4 3, 3, 3, 3, 37, 3, /, 3,, 3, 7,4 37,, 37,3,7 3, 4,7,7 4,7 34, 43, 3,3 4, 3, 3,,7 37, 7, W /,,7 7, 43,7 4,3 4,,3 4,, 4, 47, 3,4, 37,4 4, 3,3 4,, / 7 4, 43,, 4,, 4,3, 4, 7, 4,4, 3,7 3,4 3,, 37,7 4, 3, / 7, 44, 73,3 43,47, 4,7,74 4,4 3, 3,,7 3, 7,7 3, 4,3,,3 33, W / 7, 44,,4 43, 3, 4,,4 4, 4, 4, 47, 3, 44, 3, 4, 37, 3, 3,3 / 7, 43,,4 4,,4 4,, 4,, 4,4 4,7 4,, 3,, 3, 47, 37, /, 44,3 7, 43,, 4,7, 4,7, 4,, 3,3, 37, 3, 3,4 4, 34, Factors Multiplier Capacity irflow Rated of % - d ate R + BTUH BTUH......

ir Conditioning Wall-Mount Model Nomenclature W 37 X X X X X X MODEL NUMBER CPCITY - ½ Ton 4 - Ton - Ton 3 - ½ Ton 37-3 Ton 4-3½ Ton 4-4 Ton - Ton Ventilation Options Models W, W4, W3 W3, W3 W43, W44, W, W Description Factory Installed Field Installed Factory Installed Field Installed Factory Installed Field Installed Code No. Part No. Code No. Part No. Code No. Part No. Barometric Fresh ir Damper - Standard X BFD- X BFD-3 X BFD- Blank-Off Plate B BOP- B BOP-3 B BOP- Motorized Fresh ir Damper M MFD- M MFD-3 M MFD- Commercial Ventilator - Spring Return w/exhaust V CRV- V CRVS-3 V CRVS- Commercial Ventilator - Power Return w/exhaust --- --- P CRVP-3 P CRVP- Economizer - Fully Modulating E EIFM- B E EIFM-3 C E EIFM- C Economizer - Fully Modulating D N/ D N/ D N/ Energy Recovery Ventilator - 3 Volt R WERV-B- R WERV-3C - 3 R WERV-C - 3 Energy Recovery Ventilator - 4 Volt N/ N/ R WERV-C3C - 3 R WERV-CC - 3 Low ambient control is required with economizer for low temperature compressor operation. For use only with V Control Module and TCS3 Controller. 3 Intake and exhaust can be independently adjusted. Color option must be specified to match unit (X = Beige, 4 = Buckeye Gray) ir Conditioning Control Modules VILBLE CONTROL OPTIONS W, W4, W3, W3, W43 Models TDR HPC LPC 3 CCM 4 LC LR SK 7 ODT DDC Factory Installed Code Field Installed Part D CM- E CM- G CM- H CM-3 I CM- J Factory Only K CM-3 & CMC- M Factory Only Field Installed Only CMC- Field Installed Only CM-4 V Factory Only Field Installed Only CM-3 ir Conditioning Control Modules VILBLE CONTROL OPTIONS W3, W44, W, W Models TDR HPC LPC 3 CCM 4 LC LR SK 7 ODT DDC Factory Installed Code Does I CM- Not pply To These Models Field Installed Part G CM- H CM- J Factory Only K CM-3 & CMC- M Factory Only REVISION Specialty Products (Non-Standard) VOLTS & PHSE - 3/// B - 3///3 C - 4//3 KW VENTILTION OPTIONS (See Table Below) FILTER OPTIONS X - -inch Throwaway (Standard) W - -inch Washable P - -inch Pleated COLOR OPTIONS X - Beige (Standard) - White - Mesa Tan 4 - Buckeye Gray - Desert Brown - Dark Bronze For KW and circuit breakers (3/ Volt) or toggle disconnects (4 Volt) applications, insert Z in the KW field of the model number. Insert D for dehumidification with hot gas reheat Models W4, 4 & only. See Form F74 for complete details. CONTROL MODULES (See Chart Below) COIL OPTIONS X - Standard - Phenolic Coated Evaporator - Phenolic Coated Condenser 3 - Phenolic Coated Evaporator and Condenser OUTLET OPTIONS X - Front (Standard) T - Top (on W3 and W37 Models) Field Installed Only CMC- Field Installed Only CM-4 V Factory Only Field Installed Only CM-4 = Standard equipment for these specified models. TDR. Time delay relay only for compressor is fixed -minute delay-on-break to prevent short cycling. Not needed if HPC or LPC are used. See notes, 3 and 4. HPC. High pressure control is auto reset. lways used with compressor control module (CCM) which is included. See note 4. 3 LPC. Low pressure control is auto reset. lways used with compressor control module (CCM) which is included. See note 4. 4 CCM. Compressor control module has adjustable 3-second to -minute delay-on-break timer. On initial power-up, or any time the power is interrupted, the delay-on-make will be - minutes plus % of the delay-on-break setting. There is no delay-on-make during routine operation of the unit. The module also provides the lockout feature (with retry) for high and/or low-pressure controls, and a -minute timed bypass for low-pressure control. LC. Low ambient control permits cooling operation down to F LR. The alarm relay has a set of normally open and normally closed dry contacts to provide the ability to signal a condition of shutdown on either high or low pressure controls. 7 SK. Start kit can be used with all - single phase models only. Is not used or available for -B or -C three phase models. ODT. Outdoor thermostat is adjustable from to F. It is suitable for use as a compressor cut-off thermostat. DDC. Incorporates 4 additional sensors: discharge air temperature, indoor blower airflow, compressor current, and dirty filter. These sensing devices function to input analog data such as temperature, as well as digital data such as airflow, compressor status or filter status. V control module should be ordered in conjunction with direct digital controller (DDC) model TCS3. Refer to DDC specification sheet S3 for more information. Use CM-4 for Model W43. Use CM-3 for Models W3. Form No. S3- Supersedes S3- Page of

Clearances Required for Service ccess and dequate Condenser irflow MODELS LEFT SIDE RIGHT SIDE W, W4, W, W37 " " W 4, W4, W " " NOTE: For side by side installation of two () W models there must be " between units. This can be reduced to " by using a WL model (left side compressor and controls) for the left unit and W (right side compressor and controls) for right unit. See WL Specifications S37. Minimum Clearances Required to Combustible Materials MODELS W, W4, W " W 3, W37 " W 4, W4, W " SUPPLY IR DUCT FIRST THREE FEET CBINET " /4 " /4 " Refer to the Installation Manual for more detailed information. Dimensions of Basic Unit for rchitectural and Installation Requirements (Nominal) MODEL W W4 W W3 W37 W4 W4 W WIDTH (W) DEPTH (D) HEIGHT (H) SUPPLY RETURN ll dimensions are in inches. Dimensional drawings are not to scale. B C B E F G I J K L M N O P Q R S T 33.3 7. 7.3 7........... 7..3 34.3.. 4... 3. 7. 7.3 7. 7. 3. 7. 4... 7.3... 7.. 3.3..4 4... 4..43 4..... 43..3. 3. 3..4 34. 3.43 3.37 43. 3...44.. FRONT VIEW SIDE VIEW BCK VIEW *Optional top outlet (factory installed only) for W3 and W37 models only. Bard Manufacturing Company, Inc. Bryan, Ohio 4 www.bardhvac.com Since 4... Moving ahead, just as planned. Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer. Form No. S3 November, Supersedes S3- Form No. S3- Supersedes S3- Page of