Product Information Duolec Vari-Purpose Gear Lubricant (1601-1610) High-Performance Oils Maintain Effective Lubrication in High-Temperature, High-Load Applications Duolec Vari-Purpose Gear Lubricants are a high-performance line of industrial and automotive gear oils ranging from ISO VG 46 to 1500. Designed for use in any industrial gear or bearing application that requires a thermally stable, extreme pressure lubricant, they maintain their performance even after filtration. They also meet the requirements for many hypoid and planetary gears in heavy-duty mobile equipment, as well as differentials in over-the-road vehicles. They contain Duolec, LE s dual-acting additive that provides both wearreducing and EP protection. Duolec Vari-Purpose Gear Lubricants also are fortified with a shear stable tackifier to provide adhesion to metal during use. Beneficial Qualities Maintains Performance in Extreme Conditions Possesses high film strength Remains stable despite high temps Resists oxidation and sludge formation Provides wear-reducing and EP protection Adheres to Metal Contains shear-stable tackifier that allows oil to adhere to metal components Remains tacky during high shear use Resists Moisture Separates readily from water, continuing to provide effective lubrication º º Ordinary gear oils will emulsify and foam, causing increased friction and poor lubrication Filterable Contains nonsilicone antifoamants that resist removal during filtration Contains no solids that can be removed during filtration Remains within viscosity grade after filtration Proprietary Additives LE s proprietary additives are used exclusively in LE lubricants. Duolec Vari-Purpose Gear Lubricant contains Duolec. Duolec dual-acting additive imparts synergistic properties to lubricants, providing both wear-reducing and extreme pressure protection. The result of revolutionary technology designed specifically for use in LE gear lubricants, Duolec increases oil film strength and is temperatureactivated to provide a protective layer that smooths metal surfaces and minimizes the effects of any contact, thereby reducing friction and preventing surface wear. The Lubrication Reliability Source www.lelubricants.com 800-537-7683
Technical Data Duolec Vari-Purpose Gear Lubricant 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 Color Purple Purple Purple Purple Purple Purple Purple Purple Purple Purple ISO VG / SAE Grade 46 / 75W 68 / 80 100 / 85 150 / 90 220 / 110 320 / 140 460 / 190 680 / 250 1000 / 250 1500 / 250 AGMA Grade 1 EP 2 EP 3 EP 4 EP 5 EP 6 EP 7 EP 8 EP 8A EP 9 EP Relative Density ASTM D1298 Viscosity @ 100 C, cst, ASTM D445 Viscosity @ 40 C, cst, ASTM D445 Viscosity Index ASTM D2270 Flash Point C ( F), (COC), ASTM D92 Pour Point C ( F), ASTM D97 Rust Test 4 hrs @ 60 C, Sea H 2 0, ASTM D665B Copper Corrosion 3 hrs @ 121 C, ASTM D130 Timken OK Load lbs (kgs), ASTM D2782 Four-Ball EP Weld Point kgf, ASTM D2783 Four-Ball EP Load Wear Index kgf, ASTM D2783 Four-Ball Wear @ 75 C, 1200 rpm, 40 kgf, 60 minutes, mm wear, ASTM D4172 Foaming Characteristics @ 24 C/93.5 C/24 C, 3 sequences, ml of foam/time to break, ASTM D892 0.880 0.882 0.884 0.885 0.890 0.887 0.889 0.890 0.898 0.898 6.98 9.44 12.31 16.42 21.20 27.90 37.00 47.50 62.10 81.27 44.15 70.75 104.0 156.0 229.0 332.5 480.0 707.5 1015.0 1423 116 111 110 111 110 113 118 116 120 126 210 (410) 210 (410) 210 (410) 210 (410) 210 (410) 210 (410) 213 (415) 216 (420) 213 (415) 215 (419) -33 (-27) -27 (-17) -24 (-11) -24 (-11) -24 (-11) -21 (-6) -21 (-6) -15 (5) -15 (5) -18 (0) Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass 1b 1b 1b 1b 1b 1b 1b 1b 1b 1b 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 75 (34) 400 400 400 400 400 400 400 400 400 400 77.2 77.2 77.2 77.2 77.2 77.2 77.2 77.2 77.2 77.2 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0.33 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 0/0,0/0,0/0 FZG Fail Stage 14+ 14+ 14+ 14+ 14+ 14+ 14+ 14+ 14+ 14+ Performance Requirements Met or Exceeded AGMA 9005 E02 API GL-5 Chinese IGO L-CKD Cincinnati Machine DIN 51517 Part 3 David Brown H2 MIL-L-2105E Muller Weingarten DT 55-005/1 US Steel 224 Typical Applications Enclosed gearboxes Gearboxes at water and wastewater treatment facilities Bowl mills / pulverizers Homogenizers Hypoid and planetary gears in heavy-duty mobile equipment Differentials CC BY-SA 3.0 Duolec is a registered trademark of Lubrication Engineers, Inc LI30095 9-12 300 Bailey Avenue Fort Worth, TX 76107 Fax: 800-228-1142 LE operates under an ISO 9001 Certified Quality System. www.lelubricants.com 800-537-7683
Lubrication Engineers, Inc. Launches DUOLEC TM Vari-Purpose Gear Lubricants 1601 1609 DUOLEC TM Gear Lubricants supersedes famous ALMASOL VPGL FORT WORTH, Texas, USA (August, 2007) Lubrication Engineers, Inc. (LE) is proud to launch their latest exciting Enhanced Lubricant to the market a new, improved product that will supersede LE s now legendary ALMASOL Vari- Purpose Gear Lubricant: the 1601-1609 DUOLEC Vari-Purpose Gear Lubricants (DVPGL). This new product range offers LE s customers significant performance improvements versus even the impressive ALMASOL gear oils. It includes LE s new unique proprietary additive DUOLEC that was developed specifically for use in gear oil applications. The 1600 DUOLEC Series also provides many other benefits that this new gear additive technology is able to deliver including an incredible FZG Test 14 th Stage Pass, Timken OK Load of 75lbs, greater thermal stability, improved shear resistance, better water separation & the ability to be filtered to low micron levels without harming or removing additives. The 1601-1609 DUOLEC Vari-Purpose Gear Lubricants are high performance technology gear oils developed to surpass the challenges of today s more demanding applications in the industrial & mobile equipment markets. Proprietary Additive The 1601-1609 DUOLEC Vari-Purpose Gear Lubricants contain LE s new dimension proprietary additive DUOLEC - a dual acting liquid additive that shares attributes of both LE s ALMASOL & MONOLEC but offering even better wear protection. DUOLEC incorporates revolutionary new technology which is thermally activated to provide dual levels of anti-wear & extreme pressure protection that form a solid-like protective layer on the metal surface. This layer then fills surface asperities, effectively smoothing the surface & minimizing the effects of any metal to metal contact thereby reducing friction & preventing welding & surface wear. Testing for the friction reduction capabilities of DUOLEC was conducted using the SRV friction test machine. The test results showed a 25% reduction in friction over the base oil when DUOLEC was incorporated. As increasing numbers of O.E.M s are requiring more stringent cleanliness levels, this new liquid additive also allows the DVPGL line to be filtered to much cleaner levels than with ALMASOL. 300 Bailey Ave Fort Worth, TX Phone: 800-537-7683 817-916-3200 FAX: 800-228-1143 817-820-0027 www.le-inc.com
1601 1609 DUOLEC TM VARI-PURPOSE GEAR LUBRICANTS New Numbering System The DUOLEC line has a new numbering system beginning with 1601 (ISO 46) & ending with 1609 (ISO 1000) with the relevant ISO numbers in ascending order. All products apart from 1609 have their last digits relating to the AGMA Viscosity Grade numbers of the products. For example, 1605 is AGMA 5EP Grade. Additive Backbone The 1600 Series contains a new additive system that is exclusive to LE & is the result of numerous years of research. The backbone of the product is based on the proven technology used for many years in several of LE s synthetic products. The new Enhanced package provides superior performance & meets the industrial gear claims of US Steel 224 & AGMA 9005 E02 as well as the API GL-5 specification for severe automotive conditions a performance level that few other industrial gear oils are able to claim. Typical industrial gear oils are not formulated to meet this high level of performance. Improved Thermal Stability The new line is formulated with more thermally stable & oxidation resistant extreme pressure (EP) additives that do not sacrifice any load-carrying capability. Its oxidation resistance provides improved thermal stability at elevated temperatures. In fact the DUOLEC line boasts impressive EP performance with a Timken OK Load of 75lbs along with reduced deposit formation. Proprietary 3-Component Shear Stable Tackifier System LE s R&D Department has developed a new 3-component tackifier system that provides improved gear climbing & adhesion to metal surfaces whilst minimizing the amount of shear experienced by the product when in service or even when filtered to low micron levels. Improved Water Separation The incorporation of new & improved demulsifiers in the DVPGL package along with an impressive synergistic combination of additives provides even better water separation performance. The easy draining of water from a gearbox means longer oil life and no possibility of gearbox rust problems. New Defoamant The 1600 DUOLEC Series contains non-silicone Defoamants which are not easily removed when the gear oils are filtered, thus they also last longer in the oil. They help to improve the ability to monitor direct contamination during oil analysis as the gear oil does not contain silicone which can sometimes confuse customers when trying to remove dirt from their oil. Compatibility with ALMASOL Vari-Purpose Gear Lubricants The 1600 DUOLEC Series has been thoroughly tested & is completely compatible with the ALMASOL Vari- Purpose Gear Lubricant line that it is replacing meaning that LE s current gear oil customers should have no concerns about converting their gearboxes from ALMASOL to DUOLEC Vari-Purpose Gear Lubricants. They will just be able to enjoy the improved performance of a new dimension Enhanced Lubricant. Outperforms equivalent competitive products on the market The 1600 DUOLEC Series Timken OK Load of 75lbs is even 10lbs higher than LE s original ALMASOL 600 Series; resulting in better Extreme Pressure (EP) performance. Its high 4 Ball Weld Point & Load Wear Index (LWI) result in far better load carrying performance than similar competitive products on the market today. The replacement product range for our extremely popular & successful ALMASOL Vari-Purpose line was always going to have to be incredibly impressive we have done even better than planned with our new DUOLEC Vari-Purpose line. The performance of these new gear oils is just outstanding and gearbox operators worldwide will very quickly understand that DUOLEC will improve the reliability & performance of their expensive equipment their production & profits will increase, said Scott Schwindaman, President, Lubrication Engineers, Inc.
SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX 76107 MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) 834-6321 300 Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX 76107 Chemtrec: (Within USA) (800) 424-9300 (Outside USA call collect) (703) 527-3887 CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES TRADE NAME AND SYNONYMS: 1604 ISO 150/SAE 90 DUOLEC Vari-Purpose Gear Lube FORMULA: APPEARANCE: VISCOSITY: @ 210 F, SUS @ 100 C, cst Purple lubricant 85.58 16.42 ODOR: VISCOSITY: @ 100 F, SUS @ 40 C, cst Lube oil odor 815.1 156.0 RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -11 BOILING POINT: F FLASH POINT: F (Method) >500 405 (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm Hg @ 60 F) <5 0.89 SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) <83.0 5 mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 405 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA 1604 ISO 150/SAE 90 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 1
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, B and P; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity 1 1 1604 ISO 150/SAE 90 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 2
SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX 76107 MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) 834-6321 300 Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX 76107 Chemtrec: (Within USA) (800) 424-9300 (Outside USA call collect) (703) 527-3887 CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES TRADE NAME AND SYNONYMS: 1605 ISO 220/SAE 110 DUOLEC Vari-Purpose Gear Lube FORMULA: APPEARANCE: VISCOSITY: @ 210 F, SUS @ 100 C, cst Purple lubricant 106.5 21.20 ODOR: VISCOSITY: @ 100 F, SUS @ 40 C, cst Lube oil odor 1204 229.0 RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -11 BOILING POINT: F FLASH POINT: F (Method) >500 405 (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm Hg @ 60 F) <5 0.89 SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) <76.0 5 mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 405 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA 1605 ISO 220/SAE 110 DUOLEC Vari-Purpose Gear Lube Effective Date: July 16, 2007 Print Date: August 1, 2007 Page 1
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, B and P; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity 1 1 1605 ISO 220/SAE 110 DUOLEC Vari-Purpose Gear Lube Effective Date: July 16, 2007 Print Date: August 1, 2007 Page 2
SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX 76107 MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) 834-6321 300 Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX 76107 Chemtrec: (Within USA) (800) 424-9300 (Outside USA call collect) (703) 527-3887 CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES TRADE NAME AND SYNONYMS: 1606 ISO 320/SAE 140 DUOLEC Vari-Purpose Gear Lube FORMULA: APPEARANCE: VISCOSITY: @ 210 F, SUS @ 100 C, cst Purple lubricant 137.1 27.90 ODOR: VISCOSITY: @ 100 F, SUS @ 40 C, cst Lube oil odor 1757 332.5 RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -6 BOILING POINT: F FLASH POINT: F (Method) >500 410 (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm Hg @ 60 F) <5 0.89 SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) <67.0 5 mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 410 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA 1606 ISO 320/SAE 140 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 1
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, B and P; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity 1 1 1606 ISO 320/SAE 140 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 2
SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX 76107 MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) 834-6321 300 Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX 76107 Chemtrec: (Within USA) (800) 424-9300 (Outside USA call collect) (703) 527-3887 CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES TRADE NAME AND SYNONYMS: 1607 ISO 460/SAE 190 DUOLEC Vari-Purpose Gear Lube FORMULA: APPEARANCE: VISCOSITY: @ 210 F, SUS @ 100 C, cst Purple lubricant 180.0 37.00 ODOR: VISCOSITY: @ 100 F, SUS @ 40 C, cst Lube oil odor 2545 480.0 RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F -6 BOILING POINT: F FLASH POINT: F (Method) >500 415 (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm Hg @ 60 F) <5 0.89 SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) <59.0 5 mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 415 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA 1607 ISO 460/SAE 190 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 1
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, B and P; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity 1 1 1607 ISO 460/SAE 190 DUOLEC Vari-Purpose Gear Lube Effective Date: July 31, 2007 Print Date: August 1, 2007 Page 2
SUPPLIER: LUBRICATION ENGINEERS, INC. 300 Bailey Avenue FORT WORTH, TX 76107 MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) 834-6321 300 Bailey Avenue In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX 76107 Chemtrec: (Within USA) (800) 424-9300 (Outside USA call collect) (703) 527-3887 CHEMICAL NAME AND SYNONYMS: CHEMICAL FAMILY: Hydrocarbon SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES TRADE NAME AND SYNONYMS: 1608 ISO 680/SAE 250 DUOLEC Vari-Purpose Gear Lube FORMULA: APPEARANCE: VISCOSITY: @ 210 F, SUS @ 100 C, cst Purple lubricant 230.5 47.50 ODOR: VISCOSITY: @ 100 F, SUS @ 40 C, cst Lube oil odor 3778 707.5 RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F +5 BOILING POINT: F FLASH POINT: F (Method) >500 420 (C.O.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm Hg @ 60 F) <5 0.89 SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD 50 LD 50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) <51.0 5 mg/m 3 -TWA Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/industrial lubricant with a low order of toxicity and irritancy. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC 2601-2629) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 420 (C.O.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5 mg/m 3 EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA 1608 ISO 680/SAE 250 DUOLEC Vari-Purpose Gear Lube Effective Date: June 4, 2007 Print Date: August 1, 2007 Page 1
STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, B and P; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: VENTILATION: OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 1 Flammability 1 1 Reactivity 1 1 1608 ISO 680/SAE 250 DUOLEC Vari-Purpose Gear Lube Effective Date: June 4, 2007 Print Date: August 1, 2007 Page 2