Molex Premise Networks Systems Catalogue

Molex Premise Networks Systems Catalogue

PowerCat 6 The Cat 6 Solution PowerCat 6 The Cat 6 Solution The PowerCat 6 Product Range Molex Premise Networks PowerCat 6 system product range is designed to comply with the draft Category 6 standards: (TIA/EIA 568B-2-1 Draft (PN 3727), ISO/CENELEC Class E (2001), ISO/IEC JTC 1/SC 25/WG 3 N 696. The PowerCat 6 Product Range The performance of the system is enhanced by the patented Molex plug and socket combination, allowing Category 6 level performance and backwards compatibility with the Molex Premise Networks PowerCat (C5E) system. The PowerCat 6 Product Range Molex Premise Networks recommends that the full range of PowerCat 6 products is used in a system to provide the performance indicated in the draft Category 6 standard. PowerCat 6 Cable Unshielded 4 Pair PVC and LSZH Cable Central separator for the reduction of NEXT & ELFEXT 24 AWG solid conductor Colour coded pairs for ease of termination 500 metre reel PowerCat 6 MOD-SNAP Module The MOD-SNAP modular system provides a flexible and versatile method of installation, allowing the user the choice of installing as many data outlets as required. The modules are fully assembled units featuring the Molex Premise Networks low profile PowerCat 6 RJLP connector and a 25x38.5mm fascia (BT 6C size), shutter and spring assembly. enables installation. Protected labelling facility Compatible with MOD-SNAP wallplates Ideal for floorbox applications CAA-00074 Cable 500m Reel PVC - UTP CAA-00079 Cable 500m Reel LSZH - UTP - IEC 332.1 Other cable variants available - For more information contact Customer Services MMS-00001-02 MOD-SNAP RJLP Module, RJ45, 568B, UTP PowerCat 6 Patch Panels Molex Premise Networks patch panels are a versatile means for connecting horizontal cabling. Featuring an integral rear cable management tray for ease of installation and cable dressing. Port labelling is also featured for site specific network administration. Suitable for high speed data transmission, these panels were designed to meet the highest performance standards in the industry. Molex Premise Networks patented KATT IDC is terminable using industry standard tooling. Fixing kit, cable ties and installation instructions are included. 16 Ports 1U 24 Ports 1U 48 Ports 2U PCB Mounted KATT IDC EIA 568B wired RJ45 jacks Standard 19" rack mounted Graphite grey textured finish Integral cable management PowerCat 6 Euromod Module The Euromod modular system provides a flexible and versatile method of installation. This modular system offers a wide range of wallplates and modules that allow the user to install as many data outlets as required. The modules are fully assembled units featuring the Molex Premise Networks low profile PowerCat 6 RJLP connector and a 25x50mm fascia, shutter and spring assembly. enables installation. Compatible with existing range of Euromod wallplates PID-00042 PID-00043 PID-00065 16 Port Panel 1U RJ45 568B - UTP 24 Port Panel 1U 568B - UTP 48 Port Panel 2U 568B - UTP MEU-00022-02 Euromod RJLP Module, RJ45, 568B, White - UTP PowerCat 6 Patch Cords Unshielded 4 Pair Stranded Cable Pre-terminated with WE8W Molex Plugs Overmoulded strain relief boots Available in 1,2,3 and 5 metre lengths PowerCat 6 Office Block Designed in accordance with TSB75, Office Block is the ideal solution for open office cabling. Its attractive and compact design facilitates a simple, organised installation for areas where space is limited. Designed to support high speed data transmission systems, Office Block utilises the Molex Premise Networks RJSE connector. Compact, attractive and versatile 1, 2, 4 & 6 port surface mount block Cable entry from rear knockouts Labelling facility Can be mounted with screws or magnet Snap on shutters are provided Dual colour coded IDC blocks provide the option of 568A or 568B wiring PCD-00050-0* Patch Cord 1m grey - UTP PCD-00052-0* Patch Cord 2m grey - UTP PCD-00054-0* Patch Cord 3m grey - UTP PCD-00058-0* Patch Cord 5m grey - UTP * Colour Options - C = Red, E = Grey, H = Blue, J = Green, K = Yellow SID-00027-02 SID-00028-02 SID-00029-02 SID-00030-02 SID-00031-02 SID-00032-02 SID-00033-02 Office Block 1 port, RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 2 port, RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 4 port, RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 6 port, RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 2 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 4 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B - UTP Office Block 6 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B - UTP

PowerCat -UTP The Cat 5e Solution PowerCat -UTP The Cat 5e Solution The PowerCat UTP Product Range Molex Premise Networks Category 5e product range is known as the PowerCat system. Designed to meet or exceed the requirements of: TIA/EIA 568A-A5, ISO/CENELEC Class D (2002), ISO/IEC JTC 1/SC 25/ WG 3 N 696 standards. The product range offers backwards compatibility with Category 5 systems, with enhanced performance in support of the Gigabit Ethernet protocol. PowerCat UTP Cable 4 pair PVC or LSZH Cable Colour coded pairs for ease of termination 305m easy spool box and 1 km reel available PowerCat UTP Patch Cords Unshielded 4 Pair Stranded Cable Pre-terminated with WE8W Plugs Strain Relief Boots 39.A0360 4 Pair UTP, PVC, Cat 5e Cable, 305m Box 39.A0370 4 Pair UTP, PVC, Cat 5e Cable, 1km Reel CAA-00010 4 Pair UTP, LSZH, IEC332.3, Cat 5e Cable, 305m Box CAA-00071 4 Pair UTP, LSZH, IEC332.3, Cat 5e Cable, 1km Reel CAA-00069 4 Pair UTP, LSZH, IEC332.1, Cat 5e Cable, 1km Reel CAA-00070 4 Pair UTP, LSZH, IEC332.1, Cat 5e Cable, 305m Box PCD-00068-0* PCD-00069-0* PCD-00070-0* PCD-00071-0* PCD-00073-0* PCD-00072-0* * Colour Options - C = Red, E = Grey, H = Blue, J = Green, K = Yellow UTP Patch Cord 1m UTP Patch Cord 2m UTP Patch Cord 3m UTP Patch Cord 5m UTP Patch Cord 7m UTP Patch Cord 10m PowerCat UTP Patch Panels Molex Premise Networks patch panels are a versatile means for connecting horizontal cabling. Featuring an integral rear cable management tray for ease of installation and cable dressing. Port labelling is also featured for site specific network administration. Suitable for high speed data transmission, these panels were designed to meet the highest performance standards in the industry. Molex Premise Networks patented KATT IDC is terminable using industry standard tooling. Fixing kit, cable ties and installation instructions are included. 24 Ports 1U 48 Ports 2U PCB Mounted KATT IDC EIA 568B wired RJ45 jacks Standard 19" rack mounted Graphite grey textured finish Integral cable management PowerCat MOD-SNAP & Euromod Modules The MOD-SNAP & Euromod modular systems provide a flexible and versatile method of installation, allowing the user the choice of installing as many data outlets as required. The modules are fully assembled units featuring the Molex Premise Networks low profile Cat 5e RJLP connector and a 25x38.5mm fascia (BT 6C size, MOD-SNAP)) or 25x50mm fascia (Euromod), shutter and spring assembly. enables installation. Protected labelling facility Compatible with MOD-SNAP wallplates Ideal for floorbox applications (MOD-SNAP) Compatible with Euromod Wallplates 27.1B.241.A005G 24 Port Panel - With Cover, 1U, 568B PID-00058 24 Port Panel, 1U, 568B* PID-00059 48 Port Panel, 2U, 568B* * Product is available without Port Identification Markings - Contact Customer Services for Part No s. 42.1B.011.A0032 17.1B.011.A0042 MEU-00019-02 MOD-SNAP RJLP Module, RJ45, 568B, Cat 5e, White Euromod RJLP Module, RJ45, 568B, Cat 5e, White Angled Euromod RJLP Module, RJ45, 568B, Cat 5e, White PowerCat UTP High Density Patch Panels Molex Premise Networks PowerCat (C5E) High Density Patch Panels are ideal for ISP applications or installations where cabinet/rack space is at a premium. Providing 32 or 48 ports in 1U, these patch panels offer an integral rear cable management tray specifically designed for neat and easy cable dressing. The front of the panel has a protected labelling facility for clear port labelling. Suitable for high speed data transmission, this panel was designed to meet the highest performance standards in the industry, utilising the PowerSum principle of measurement and testing. PID-00073 PID-00074 PowerCat (C5E) performance 32 Ports 1U 48 Ports 1U PCB Mounted KATT IDC EIA 568B wired RJ45 Jacks Standard 19 rack mounted Graphite grey textured finish 48 Port PowerCat (C5E) Patch Panel 1U 32 Port PowerCat (C5E) Patch Panel 1U PowerCat Office Block Designed in accordance with TSB75, Office Block is the ideal solution for open office cabling. Its attractive and compact design facilitates a simple, organised installation for areas where space is limited. Designed to support high speed data transmission systems, Office Block utilises the Molex Premise Networks RJSE connector. SID-00009-02 SID-00010-02 SID-00011-02 SID-00012-02 SID-00024-02 SID-00025-02 SID-00026-02 Compact, attractive and versatile 1, 2, 4 & 6 port surface mount block Cable entry from rear knockouts Labelling facility Can be mounted with screws or magnet Snap on shutters are provided Dual colour coded IDC blocks provide the option of 568A or 568B wiring Office Block 1 port, RJ45, RJSE, Shuttered, White, 568A/B Office Block 2 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B Office Block 4 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B Office Block 6 port (with magnet), RJ45, RJSE, Shuttered, White, 568A/B Office Block 2 port, RJ45, RJSE, Shuttered, White, 568A/B Office Block 4 port, RJ45, RJSE, Shuttered, White, 568A/B Office Block 6 port, RJ45, RJSE, Shuttered, White, 568A/B

PowerCat - FTP The Cat 5e Solution PowerCat - FTP The Cat 5e Solution The PowerCat FTP Product Range Molex Premise Networks Category 5e product range is known as the PowerCat system. Designed to meet or exceed the requirements of: TIA/EIA 568A-A5, ISO/CENELEC Class D (2002), ISO/IEC JTC 1/SC 25/ WG 3 N 696 standards. The product range offers backwards compatibility with Category 5 systems, with enhanced performance in support of the Gigabit Ethernet protocol. PowerCat FTP Cable 4 pair PVC or LSZH Cable Colour coded pairs for ease of termination 305m easy spool box and 1 km reel available PowerCat MOD-SNAP FTP Module The MOD-SNAP modular system provides a flexible and versatile method of installation, allowing the user the choice of installing as many data outlets as required. The modules are fully assembled units featuring the Molex Premise Networks low profile Cat 5e RJLP connector and a 25x38.5mm fascia (BT 6C size), shutter and spring assembly. Protected labelling facility Compatible with MOD-SNAP wallplates Ideal for floorbox applications CAA-00013 CAA-00021 CAA-00048 CAA-00049 CAA-00072 CAA-00073 4 Pair FTP, PVC, Cat 5e Cable, 305m Box 4 Pair FTP, LSZH, IEC332.3, Cat 5e Cable, 305m Box 4 Pair FTP, PVC, Cat 5e Cable, 1km Reel 4 Pair FTP, LSZH, IEC332.3, Cat 5e Cable, 1km Reel 4 Pair FTP, LSZH, IEC332.1, Cat 5e Cable, 1km Reel 4 Pair FTP, LSZH, IEC332.1, Cat 5e Cable, 305m Box enables installation. The FTP connector provides continuity of the cable shield by providing a termination point for the drain wire. MMS-00004-02 MOD-SNAP RJLP Module, RJ45, 568B, Cat 5e, White PowerCat FTP & STP Patch Panels The 16 and 24 Port Sliding STP Patch Panels allow easy front loading access for installation, termination and maintenance. A fixed 24 Port version of this panel is also available and full shielding is achieved on all versions by the provision of a braided foam RFI strip on the base and cover of the panel into which the foil or braid of the cable is pressed after termination. The 24 Port FTP Patch Panel offers through shield continuity and is a versatile method of connecting horizontal cabling in a FTP environment. PID-00019 PID-00026 PID-00030 PID-00075 16 & 24 Port Sliding or Fixed STP version FTP 24 Port 568A/B wired Integral rear cable management Port Identification 19 rack mounted Graphite Grey finish 24 Port Sliding Panel, 1U, 568A/B, STP 16 Port Sliding Panel, 1U, 568A/B, STP 24 Port Fixed Panel, 1U, 568A/B, FTP 24 Port Fixed Panel, 1U, 568A/B, STP PowerCat Euromod FTP Modules The Euromod modular system provides a flexible and versatile method of installation. This modular system offers a wide range of wallplates and modules that allow the user to install as many data outlets as required. The modules are fully assembled units featuring the Molex Premise Networks low profile Cat 5e RJLP connector and a 25x50mm fascia, shutter and spring assembly. enables installation. The FTP connector provides continuity of the cable shield by providing a termination point for the drain wire. MEU-00020-02 Compatible with Euromod Wallplates Euromod RJLP Module, RJ45, 568B, Cat 5e, White PowerCat FTP Patch Cords Shielded 4 Pair Stranded Cable Pre-terminated with WE8W Plugs Strain Relief Boots PowerCat Euromod 360 STP Module The RJ45 shuttered module is designed specifically for areas where there are high levels of Electro Magnetic Interference (EMI) and offers the user 360 shield protection. A two piece Die Cast shield is used for simple installation avoiding sharp edges which might damage cable. Die cast shield for EMC protection RJ45 shuttered and with label facility PCD-00101-0* PCD-00102-0* PCD-00103-0* PCD-00104-0* PCD-00105-0* PCD-00106-0* * Colour Options - C = Red, E = Grey, H = Blue, J = Green, K = Yellow FTP Patch Cord 1m FTP Patch Cord 2m FTP Patch Cord 3m FTP Patch Cord 5m FTP Patch Cord 7m FTP Patch Cord 10m These fully assembled modules utilise Molex Premise Networks unique patented RJLP RJ45 connector. MEU-00003-02 PowerCat 360 Single Channel Euromod RJLP Module, RJ45, 568B, Cat 5e, White

Wallplates Auxiliary Products Wallplates Molex Premise Networks Wallplate systems are a highly popular economic alternative to the Euromod and MOD-SNAP systems. These plates form part of the PowerCat product range. Fixed Wallplates The wallplates are a complete assembly and include connector. Offering a low profile, space saving design that enables installation in shallow backboxes and trunking. UK standard 86x86 mm fascia Spring loaded Shutters 1 or 2 port options available UTP or FTP ISDN Range The Molex Premise Networks ISDN range offers a versatile method of installing ISDN services in a structured cabling environment. Built-in resistors provide the correct termination of the ISDN Basic Rate S-Bus. Fitted with built-in resistors 24 Port Patch Panel Euromod, MOD-SNAP and fixed wallplate options available Blue shutter distinguishes ISDN No special application tooling requirements Fully compliant with ISO 8877 WNC-00007-02 WNC-00008-02 WNC-00010-02 WNC-00011-02 1 Port PowerCat Fixed Shuttered UTP Wallplate 568B Cat 5e, White 2 Port PowerCat Fixed Shuttered UTP Wallplate 568B Cat 5e, White 1 Port PowerCat Fixed Shuttered FTP Wallplate 568B Cat 5e, White 2 Port PowerCat Fixed Shuttered FTP Wallplate 568B Cat 5e, White 27.00.240.A001G 24 Port ISDN BUS Panel 17.10.017.A0012 Euromod ISDN Module, RJLP, Basic Rate, White 18.10.017.A0012 ISDN Basic Rate Wallplate, RJLP, White 18.10.027.A0012 ISDN Basic Rate and RJ45 Cat 5e Double Wallplate, RJLP, White 42.10.017.A0012 MOD-SNAP ISDN Module, RJLP, Basic Rate, White 42.A0020 RJ45 to RJ45 Socket, 150mm Line Adapter Unit ISDN Basic Rate Quadplate The 4 Port shuttered fixed wallplate (Quadplate) is a complete assembly, comprising 4 Cat 5e RJLP RJ45 connectors, fascia, spring loaded shutters and protected labelling facility. The density of the wallplate makes it ideal for situations where several services are required in one location e.g. voice, data, video conferencing. UK standard 86x86 mm fascia UTP or FTP Line Adapter Units The Molex Premise Networks Line Adapter Unit allows telecommunications equipment fitted with standard BT telephone plugs to be connected to RJ45 based structured cabling systems. Ideal for floorbox applications OFTEL GA5 approved Converts a direct line to RJ45 cabling system Flying lead for flexibility The Quadplate is designed to fit in standard UK backboxes (86x86mm external dimension) with 2 (only) screw fixing positions. The minimum internal backbox dimension clearance allowable is 76x76mm up to 81x81mm. WNC-00009-02 WNC-00016-02 4 Port PowerCat Shuttered UTP Wallplate 568B Cat 5e, White 4 Port PowerCat Shuttered FTP Wallplate 568B Cat 5e, White 42-111-1A RJ45 to BT6L Socket, 150mm Cord (PSTN) 42-112-1A RJ45 to BT6L Socket, 3m Cord (PSTN) 42-111-2A RJ45 to BT6L Socket, 150mm Cord (PABX) 42-112-2A RJ45 to BT6L Socket, 3m Cord (PABX) 42-114 RJ45 to BT6L Socket, 150mm Cord Secondary 42-130 RJ12 to BT6L PABX 150mm (Analogue - Secondary, Pins 4 & 5 digital) Euromod and MOD-SNAP Wallplates The Euromod and MOD-SNAP wallplate systems provide a flexible and versatile method of installation. Available in single and double gang versions the wallplates are designed to accept Euromod (25x50mm fascia) and MOD-SNAP (25x38.5mm fascia) modular ranges. Euromod - 50x50mm aperture MOD-SNAP - 38.5x22mm aperture Flexible system allowing the installation of as many modules as required Testers and Tooling The SLT3S Tester is a rugged, lightweight product designed to verify the integrity of 1-, 2-, 3-, and 4-pair UTP or STP channels. Incorporating a unique 3-in-1 design, this tester features built-in modular jacks for USOC, 568A and 568B wiring sequences. Innovative 3-in-1 design features modular jacks for testing USOC, 568A and 568B cabling systems Accurately verifies the continuity and sequence of 1, 2, 3, and 4 pair UTP and STP channels Continuously-sequencing LED display provides a diagnostic readout that immediately detects shorts, opens, reversals and mis-wires at a glance 17-0101-02 Euromod Unlabelled Single Gang Wallplate - 86x86x10mm 17-0102-02 Euromod Unlabelled Double Gang Wallplate - 86x145x10mm 17-0111-02 Euromod Labelled Single Gang Wallplate - 86x86x10mm 17-0112-02 Euromod Labelled Double Gang Wallplate - 86x145x10mm 42-311-02 MOD-SNAP Single Gang, Single Aperture - 86x86mm 42-312-02 MOD-SNAP Single Gang, Double Aperture - 86x86mm 42-314-02 MOD-SNAP Double Gang, 4 Aperture - 86x146mm NOTE : There are numerous Blank Modules, Bezels and Backboxes available - Contact Customer Services for more information. The termination tool was designed to provide a reliable connection at a highly competitive price. Originally developed to support the Molex Premise Networks KATT connector, the tool offers low-impact force termination, which reduces strain on the installer. Low-impact termination force Scissor style cut off Wire cutting immobiliser switch Light-weight impact resistant handle 14-0400-001 Termination Tool 33A-100-10 SLT3S Shielded Tester with 9 Volt battery (U.K.) 33-100-P SLT3 Carry Case

Molex Premise Networks Fibre Product Range Molex Premise Networks manufactures some of the most comprehensive fibre systems in the structured cabling market. Incorporating a variety of connector technology, such as; ST, Duplex SC, MTRJ, Escon, FDDI and FC. Molex Premise Networks offer total fibre solutions, ideal for either Backbone or To-The-Desk applications. Range Range Molex Premise Networks fibre range consists of; Management Panels, Enclosures, Adapter Plates, Connectors, Modules, Cable, Pre-Terminated Solutions, Adapters, Patch Cords, Splicing Equipment, Field Termination Connectors, Tool Kits and Testers. Tight Buffered Fibre Cable 900µM Tight Buffered Internal / Duct grade Aramid Yarn Strength Member ULSZH Sheath Sliding Fibre Management Panels The Sliding FMP panel is a 1U Fibre Optic panel for 24 adapter ST, 12 adapter Duplex SC & 24 adapter MTRJ. The Sliding FMP uses a sliding cable management tray to enable easy front access & termination. The depth adjustable mounting provides protection for the outgoing cable assemblies. Up to 24 adapter ST and MTRJ, and 12 adapter Duplex SC and Shuttered Duplex SC Depth Adjustable mounting Self adhesive fibre cable management system in loaded panels Two points of strain relief for fibre cable Ideal when easy access to the panel for adds, changes or maintenance is required. 62.5/125µM 50/125µM CFR-00341 CFR-00342 2 Core CFR-00261 CFR-00271 4 Core CFR-00262 CFR-00272 6 Core CFR-00263 CFR-00273 8 Core CFR-00264 CFR-00274 12 Core CFR-00265 CFR-00275 16 Core CFR-00343 CFR-00344 24 Core 30.A021G 30.A022G 30.A018G RFR-00014 RFR-00015 30.A023G RFR-00060 Fully Loaded ST Patch Panel, Cable Accessory Kit - MM Fully Loaded with ST adapters, Cable accessory kit - SM Unloaded, 24 Port ST Fully Loaded Shuttered Duplex SC Patch Panel, Cable Accessory Kit - MM Fully Loaded Shuttered Duplex SC Patch Panel, Cable Accessory Kit - SM Unloaded, 24 Port Duplex SC Fully Loaded with 24 MTRJ adapters - MM & SM Tight Buffered Fibre Cable 900µM Tight Buffered Internal / Duct grade Aramid Yarn Strength Member ULSZH Sheath E Glass Yarn - Rodent Resistant Fibre Enclosures Molex Premise Networks fibre optic enclosures are designed to suit any installation requirements. They range from the 12 fibre 601 box to the 72 fibre Demarc cabinet. All enclosures contain features for fibre management, splice holding, cable retention and labelling. All common adapter types are catered for in the form of configurable Euromod or Six-Pak Modules. ST, SC, & MTRJ variants available Demarc Cabinet can contain up to 72 fibres 601 Enclosure excepts Mechanical and Fusion Splices Security Lockable 601 Box 62.5/125µM 50/125µM 9/125µM CFR-00339 CFR-00340 CFR-00345 2 Core 91.A1000 CFR-00239 CFR-00346 4 Core CFR-00250 CFR-00240 n/a 6 Core 91.A1010 CFR-00241 CFR-00347 8 Core 91.A1020 CFR-00242 CFR-00348 12 Core 91.A1030 CFR-00243 n/a 16 Core CFR-00349 CFR-00350 n/a 24 Core 15.B033G WFR-00022 WFR-00023 WFR-00025-02 WFR-00028-02 WFR-00031-02 WM-12 Wall Mounted Enclosure 36P Patch/Splice Demarc Cabinet 72P Patch/Splice Demarc Cabinet Fully Loaded 8 Port 601 Box, ST - MM Fully Loaded 8 Port 601 Box, Duplex SC - MM Fully Loaded 12 Port 601 Box, MTRJ - MM & SM Demarc Cabinet Fibre Management Panels The Fibre Management Panel is a 1U 19" Rack mounted panel which allows direct mounting of the connectors into the front panel. Available in 24 adapter ST, 12 adapter Duplex SC and 24 adapter MTRJ versions all loaded panels come complete with a full range of cable fixing accessories. 19" rack compatible Up to 24 adapter ST and MTRJ, and 12 adapter Duplex SC and Shuttered Duple SC Self adhesive fibre cable management system on loaded panels Two points of strain relief for incoming fibre cable Termination Tooling As fibre continues to migrate into the network the need for frequent termination setups, involving few fibres, will continue to increase. Traditional terminations that require power ovens (traditional or pre-loaded epoxy) or expensive tooling (splicing and crimping) are no longer practical. Low insertion loss of 0.32 db Typ. Operating Temperature - 10 C to 60 C Complies with EIA/TIA 568A Termination time - 2 minutes 30.A011G 30.A012G 30.A008G 30.A016G 30.A017G 30.A013G RFR-00057 Fully Loaded with ST adapters, cable accessory kit - MM Fully Loaded with ST adapters, cable accessory kit - SM Unloaded, 24 Port ST Fully Loaded with Duplex SC adapters, cable accessory kit - MM Fully Loaded with Duplex SC adapters, cable accessory kit - SM Unloaded, 24 Port Duplex SC Fully Loaded with 24 MTRJ adapters - SM & MM The X-Press Termination Kits offer field terminable connectors, that are cost effective and require minimal tooling. 91.A1230 X-Press Termination Kit, 12 ST Connectors 91.A1270 X-Press ST Termination toolkit AFR-00011 X-Press Termination Kit, 12 Simplex SC Connectors AFR-00006 X-Press SC Termination toolkit

Fibre Adapters Molex Premise Networks offer a comprehensive range of adapters, both multimode and singlemode. These adapters can be used in fibre management panels, wall enclosures and wall outlets ST, SC, MTRJ, Escon & FDDI variants available Flange, Snap and Screw mount For complete list of available adpaters speak to Customer Services Angled Euromod Modules Euromod is a modular range of outlets, plates and connectors designed for use in different countries. In addition to the existing range of Euromod modules for use with copper media, Molex Premise Networks also provides a range of solutions for Fibre Optic applications. Angled 50x50mm module Available with ST, shuttered Duplex SC/ST, shuttered Duplex SC, FDDI/ST, ESCON/ST, MTRJ & Shuttered MTRJ Adapters Multimode & Singlemode configuration Compatible with 32mm deep trunking Permits a 30mm bend radius 91.A0160 ST Adapter, MM, Metal body 91.A0150 ST Adapter, MM, Polymeric body 91.A1190 Shuttered Duplex SC/Duplex SC, MM, Flange mount 91.A1300 Shuttered Duplex SC/Duplex SC, MM, Snap mount 91.A0430 Duplex SC/Duplex SC, MM, Flange mount 91.A0500 Duplex SC/Duplex SC, MM, Snap mount AFR-00126 MTRJ/MTRJ, MM & SM, Flange mount In combination with the existing Euromod product range and Fibre Management Back Box these angled modules will provide a unique fibre to the desk solution. MEU-00005-02 MEU-00009-02 MEU-00043-02 MEU-00044-02 Euromod Angled ST/ST, MM, 50x50mm, 4 Adapters Euromod Angled Shuttered Duplex SC/SC, MM, 50x50mm, 2 Adapters Euromod Angled MTRJ/MTRJ, MM, 50x50mm, 2 Adapters Euromod Angled Shuttered MTRJ/MTRJ, MM, 50x50mm, 2 Adapters Fibre Connectors Molex Premise Networks offer a comprehensive range of connectors for LAN applications. The connectors are available for singlemode or multimode applications. Manufactured with a ceramic ferrule to ensure quality and performance ST, SC, MTRJ, Escon & FDDI variants available For complete list of available connectors contact Customer Services AFR-00150 Field Terminable MTRJ, MM 62.5/125 Polishless Connector - Male AFR-00168 Field Terminable MTRJ, MM 50/125 Polishless Connector - Male 91.A0084 ST, MM, Polymeric nut 91.A0094 ST, MM, Metal nut 91.A0104 ST, MM, Metal nut - 90 boot 91.A0114 ST, MM, Metal nut - 900µm boot 91.A0290 SC, MM, Ceramic ferrule, 90 boot 91.A0310 SC, MM, Ceramic ferrule, 900µm boot Enclosure Application Euromod Modules Euromod is a modular range of outlets, plates & connectors designed for use in different countries. In addition to the existing range of Euromod modules for use with copper media, Molex Premise Networks also provides a range of solutions for Fibre Optic applications. These modules are designed for use within the WM-12 fibre enclosure. 25x50mm & 50x50mm modules Euromod compatible Available with ST, Duplex SC, Shuttered Duplex SC and MTRJ adapters Multimode & Singlemode configuration Other variants available for more information contact Customer Services 17-0423-02 Euromod ST,MM fibre module, 25x50mm, 2 Adapters 17.A0162 Euromod Duplex SC,MM fibre module, 25x50mm, 1 Adapter 17.A0202 Euromod Duplex Shuttered SC, MM fibre module, 25x50mm, 1 Adapter MEU-00032-02 Euromod MTRJ, MM & SM fibre module, 25x50mm, 2 Adapters 17.A0312 Euromod ST/ST, MM fibre module, 50x50mm, 6 Adapters 17.A0252 Euromod Duplex SC/SC, MM fibre module, 50x50mm, 3 Adapters MEU-00033-02 Euromod MTRJ, MM & SM fibre module, 50x50mm, 4 Adapters Fibre Patch Cords We offer a comprehensive range of fibre optic cable assemblies for singlemode and multimode applications. Stocks are available in 1m, 2m, 3m, and 5m lengths, see matrix below for Part No. configuration. Connector Type, each end : 0 = No connector (pigtails) 1 = ST 2 = FDDI 3 = SC 4 = ESCON 5 = ST II 6 = ST with right angle boot 7 = SMA Fibre Type : 5 = 50/125µm 6 = 62.5 / 125µm 8 = 9/125µm (SM) Jacket Type : 2 = LSZH 8 = SC with right angle boot 9 = SC Duplex F = FC/PC M = ModLink L = LC A = MTRJ - Male B = MTRJ - Female Lowest Number First Cable Type : 1 = Simplex 2 = Duplex 3 = 900µm 91.xx.xx2.xxxxx For example : To order a 1 metre Duplex LSZH 62.5 ST to SC Patch Cord, the part number would be 91.19.622.0010N Jacket Colour E = Dark Grey (50/125µm) K = Yellow (9/125µm) N = Orange (62.5/125µm) Polishing Code : 0 = Standard 1 = SM, RL > 45dB 2 = SM, RL > 55dB 3 = SM, RL > 70dB (angle polish) Length Metres Fibre Management Back Box The Fibre Management Back Box provides accommodation for direct termination or splicing of up to eight fibres and is designed to maintain the minimum bend radius requirements for fibre optic cable when used in conjunction with Euromod Angled Modules. This product is also suitable for applications which require copper modules, and can accommodate up to2 flat Euromod PowerCat or secondary voice modules as well as 4 fibres. It is packaged complete with threaded inserts for trunking applications and adhesive strip for mounting in a surface mount backbox. WFR-00044-02 Fits inside 32mm UK standard double gang backbox for surface mount applications Up to 8 fusion splices can be accommodated securely Provides storage for up to 8m of 900µM tight buffered fibre Correct bend radius maintained when used with angled modules No additional backbox required for trunking applications Mixed media capability Fibre Management Back Box

Cable Management Molex Premise Networks Cable Management Cable Management is an important part of any installation. Combining aesthetics with functionality, the Molex Premise Networks range of rack mountable cable management products offer cable management with minimal effort. Molex Premise Networks offer a extensive range of cabinet solutions from wall and floor mounted cabinets to the innovative Universal Patching Frame. Range The basic design principle of the Universal Patching Frame (UPF) is to provide a simple cable loom support with maximum accessibility, together with a universal patch panel mounting facility. Range Fibre Adapter Plates Molex Premise Networks provides a simple solution which allows you to field configure many of its fibre optic products using 6-Pak adapter plate. The plates are loaded with high quality Duplex SC, ST, MTRJ, FC, FDDI, and ESCON adapters. No tools are required as the plates install with a simple snap rivet, making installation and changes simple. AFR-00112 AFR-00115 AFR-00119 AFR-00159 AFR-00121 Available with ST, Duplex SC and MTRJ adapters Multimode & Singlemode configuration For use within the Demarc Cabinet Simple snap rivet installation Other variants available for more information contact Customer Services 6-Pak ST, MM ST to Duplex SC, MM Duplex SC, MM (Beige) 6-Pak MTRJ, SM/MM Blanks - 4/pkg Cable Management Ring Run Panels come complete with flexible plastic rings which are designed to aid installations by providing a speedy method of cable dressing. Blank Panels provide the in-fill for the tidy looking cabinet installation. Cable tidy brush panel offers the user the ability to hide unsightly cables behind the brush, but with the convenience of access to these cables if necessary. 25.A013G 25.A016G 25.A018G 25.A019G 25.A029G 25.A046G 25.A047G 19" Rack Mountable 1U and 2U Styling complements Molex Patch Panel Range Graphite (standard) and RAL 7032 (beige) colour finishes available 2U Ring Run Panel (5 Rings) 1U Ring Run Panel (5 Rings) 1U Blank Panel 2U Blank Panel 1U Cable Tidy Brush Panel 2U Ring Run Cover (6 Pack) 1U Ring Run Cover (6 Pack) Splicing Accessories If splicing is your preferred method of terminating fibre, Molex Premise Networks can supply all the consumables necessary. The splice tray is suitable for fusion and mechanical splices, and fits neatly in our patch panels and enclosures. Accepts up to 12 Fusion splices or 10 Mechanical splices For use within fixed and sliding Fibre Management Panels, FMS Plus and the Demarc cabinet 91.A1150 Fibre Fusion Splice Tray with Cover, Including 2 fusion splice holders 91.A1160 Fibre Splice Tray with Cover, Including 2 mechanical splice holders 91.B0110 Mechanical Splice MM 91.B0120 Mechanical Splice SM KFR-00008 45mm Splice Protector KFR-00009 61mm Splice Protector Optical Loss Tester Molex Premise Networks FLT4 Optical Loss Test Set is an easy to use and inexpensive solution for attenuation testing of multimode systems. The FLT4 test set consists of a dual wavelength optical power source and optical power meter in a rugged plastic carry case complete with ST adapter cap and operation manual. In addition, each optical source and optical power meter features rubber protective boots to prevent accidental damage or abuse to the units. TFR-00002 AFR-00096 Low cost Loss measurement Hand held units Field portable Units housed in rubber protective boots Rugged carry case User friendly Battery operated Zero Out option FLT4 Optical Loss Test Set Replacement ST Adapter Cap ST and STII, ESCON and MTRJ are registered trademark of Lucent Technologies, IBM and AMP Technologies respectively. Universal Patching Frame (UPF) The universal patching frame is 42U high and available in a 42 arm version. The tubular construction also ensures that the minimum bend radius, as specified by ISO/IEC 11801 and ANSI/TAI/EIA-568-A, is not exceeded preventing cable from being damaged or performance impaired. Conventional cable trays have been replaced with an open 50mm x 25mm steel wire mesh, to give finger through access to assist in tracing patch cord paths and tying off. Equipment mounting angles are secured by bolts which allow for installation of 19 or 530mm patch panels. Fixings are provided for optional, rear mounting verticals. The frame can be totally enclosed with the addition of side covers and front and rear doors. Cable-friendly tubular construction ensures system integrity Open frame maximises access for fast and simple installation Horizontal arms enhance cable management 19 inch standard allows active equipment and cabling to be accommodated in the same cabinet Minimal footprint saves space Lockable doors option for added security Baying kit allows frames to be linked together in large installations Clean earth bus bar for shielded applications Range of accessories (see specification below) Suitable for copper and fibre applications Slip joint construction allows the frame to be delivered in flat-pack and quickly assembled UPF-00021 42u Open frame assy - 42 arm (Product packaged in 2 cartons) UPF-00002 Front sill assy kit (1) UPF-00003 Glass door assy (2 halfwidth doors) UPF-00004 Side cover - left UPF-00005 Side cover - right UPF-00006 Rear door assy kit UPF-00007 Top cover ventilated UPF-00008 Fan tray - c/w 2 fans UPF-00009 Fan tray - c/w 4 fans UPF-00010 Equipment mounting angles (2) UPF-00011 Baying kit UPF-00012 Bus bar assy UPF-00013 Service shelf (3) UPF-00014 Modem shelf UPF-00022 Power dist unit - 10 way vert (UK) UPF-00016 Power dist unit - 6 way hor (UK) UPF-00018 Fixed shelf - 400mm deep UPF-00019 Fixed shelf - 600mm deep The information in this document is subject to change without notice. Molex Premise Networks assumes no responsibility for any errors that may appear in this document

EMEA Headquarters Hampshire, England Tel: 44 (0)1489 572 111 Fax: 44 (0)1489 559 106 France Paris, France Tel: 33 (0)1 39 30 59 90 Fax: 33 (0)1 39 30 59 99 Africa Midrand, South Africa Tel: 27 11 314 1010 Fax: 27 11 314 1270 Nordic Stockholm, Sweden Tel: 46 8 594 211 25 Fax: 46 8 594 211 20 Corporate Headquarters Hudson, NH 03051 U.S.A. Tel: 603 324 0200 Fax: 603 577 8770 Visit our Web site at http: // www.molexpn.co.uk UK-SC002 Printed in UK/7k/JB/JB/2001.6 2001, Molex