INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly presents two problems: 1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s). 2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration. INSTALLATION DIFFICULTY: 2OUT OF 5 ESTIMATED TIME: 1-2 HOURS SPECIFICATIONS Enclosure Type: Sealed Driver Type: 10TW3-D4 Nominal Impedance: 2 ohms Continuous Power Handling: 400 watts (RMS method) Thank you for choosing a JL Audio Stealthbox for your automotive sound system. With proper installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure. INCLUDED HARDWARE (1) Rear Bracket (1) Side Bracket (2) 3/8-16 x 1 Hex Bolt (4) 3/8 Flat Washer (4) 3/8 x 1-1/4 Diameter Flat Washer (5) 3/8 Lock Washer (5) 3/8-16 Hex Nut (3) 3/8-16 U-Nut (3) 3/8-16 x 2-1/4 Set Screw (1) 3/4 Aluminum Spacer (2) 6mm x 1.0 Flange Nut We strongly recommend that you have your new Stealthbox installed by your authorized JL Audio dealer. The installation professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your own installation, please read this installation guide completely before beginning the process.
POWER RECOMMENDATION JL Audio recommends high quality amplifiers such as the JL Audio XD300/1v2. The diagram below shows the recommended crossover settings for the XD300/1v2. For a detailed description of the amplifier settings, consult the owner s manual for the amplifier. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier. CONNECTIONS Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox amplifier. Other kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplifier. JL Audio recommends using 12AWG speaker wire for subwoofers. Page 2 JL Audio, Inc., 2017
SB-C-CTS/10TW3 INSTR_SKU# 011343 Page 3 JL Audio, Inc., 2017 STEP 1 STEP 5 Empty out the trunk of the vehicle. Disconnect the negative battery post connection. On the driver s side of the trunk, unscrew the upper net button. Remove each of the clips that hold the trunk liner in place. STEP 2 STEP 6 Unclip the covers around each of the upper tie-down hooks. Pull the trunk liner away from the trunk wall. STEP 3 STEP 7 Unscrew each of the lower net buttons. Remove the trunk floor panel. Unclip the computer from the bracket located on the fender well. STEP 4 STEP 8 Carefully unclip and remove the trunk sill panel. Remove the two nuts that hold the computer bracket to the fender well, and remove the bracket.
SB-C-CTS/10TW3 INSTR_SKU# 011343 STEP 9 STE P 13 Unplug all of the harnesses from the factory amplifier. Secure the bottom of the Rear Bracket to the hole from Step 11 using a 3/8-16 x 1 Hex Bolt, two 3/8 Flat Washers, a 3/8 Lock Washer, and a 3/8-16 Hex Nut as illustrated in Step 12. Do not tighten at this time. STEP 10 STE P 14 Remove the four nuts that hold the amplifier to the trunk wall, and remove the amplifier. Align the upper right side of the Rear Bracket vertically with the raised portion of the trunk wall as shown. Mark the location of the upper hole on the trunk wall. Rotate the bracket out of the way and drill a 7/16 hole on the mark. Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, tires, transmission lines, electrical wiring, exhaust systems or anything else that might cause a reduction in your weekly pay. S T E P 11 STE P 15 Locate the factory hole at the bottom of the trunk wall, and enlarge the hole to 7/16. Rotate the Rear Bracket back into position. Secure the top of the Rear Bracket to the hole from the previous step using a 3/8-16 x 1 Hex Bolt, two 3/8 Flat Washers, a 3/8 Lock Washer, and a 3/8-16 Hex Nut as illustrated in Step 12. Firmly tighten both the upper and lower hardware. Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, tires, transmission lines, electrical wiring, exhaust systems or anything else that might cause a reduction in your weekly pay. Slide a 3/8-16 U-Nut over each of the other holes in the Rear Bracket. Always wear eye protection when drilling! S TE P 12 STEP 16 Refer to this illustration for clarity in Steps 13, 15, and 19. Align the Side Bracket over the two lower computer bracket studs. Secure the bracket with a pair of 6mm x 1.0 Flange Nuts. Slide a 3/8-16 U-Nut over the other hole in the Side Bracket. Page 4 JL Audio, Inc., 2017
SB-C-CTS/10TW3 INSTR_SKU# 011343 S T E P 17 STEP 21 Reinstall the computer bracket over the Side Bracket as shown. Thread a 3/8-16 x 2-1/4 Set Screw through the 3/8 16 U-Nut, leaving approximately 1-1/4 exposed. Slide a 3/4 Aluminum Spacer over the rear 3/8-16 x 2-1/4 Set Screw as shown. Slide a 3/8 x 1-1/4 Diameter Flat Washer over the Aluminum Spacer. STEP 18 STEP 22 Reinstall the factory amplifier and reconnect each of the wiring harnesses. Using a Phillips head screwdriver, remove the subwoofer from the Stealthbox. Connect speaker cable to the terminal cup, and place the empty enclosure into position, allowing the three 3/8-16 x 2-1/4 Set Screws to pass through the holes in the back of the enclosure. STEP 19 STEP 23 Thread a 3/8-16 x 2-1/4 Set Screw through each of the 3/8-16 U-Nut on the Rear Bracket leaving approximately 1-1/4 exposed as illustrated in Step 12. Slide a 3/8 Flat Washer, a 3/8 Lock Washer, and a 3/8-16 Hex Nut onto each of the three 3/8-16 x 2-1/4 Set Screws and fully tighten. Reinstall the subwoofer. Page 5 JL Audio, Inc., 2017 STEP 20 STEP 24 Route speaker cable to the Stealthbox location. Push the trunk liner back into position and cut three holes in the liner to allow the three 3/8-16 x 2-1/4 Set Screws to pass through. Empty out the rear seat area of the vehicle.
STEP 25 Unclip and remove the rear seat cushion. STEP 29 Carefully unclip the screw cover on the C-pillar. STEP 26 Remove the four nuts that hold the lower portion of the rear seat back in place. STEP 30 Remove the screw. STEP 27 From inside the trunk, remove the four nuts that hold the upper portion of the rear seat back in place. STEP 31 Unclip and remove the pillar. Repeat Steps 28-30 for the opposite side. STEP 28 Remove the rear seat back. STEP 32 Remove the clips that hold the rear deck in place. Page 6 JL Audio, Inc., 2017
STEP 33 Unclip and remove the rear deck. CONGRATULATIONS! You have completed the installation for this model. Enjoy your new Stealthbox! STEP 34 Remove the four factory subwoofer mounting bolts. STEP 35 Unplug and remove the factory subwoofer. Note: Failure to remove the factory subwoofer will limit the performance of the Stealthbox. MID/HIGH FREQUENCY DRIVER FITMENT A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle. Front Speaker Size / Location: 3-1/2 - Dash Fits JL Audio Models: TR350-CXi, & C2-350x STEP 36 Reinstall the rear deck, pillars, rear seat back, and rear seat cushion. Reconnect the negative battery post connection. Front Speaker Size / Location: 9 - Front Doors Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-650, C5-650x, C5-650, & ZR650-CSi Rear Speaker Size / Location: 5-1/4 - Rear Door Fits JL Audio Models: TR525-CXi, C2-525x, C2-525, C3-525, C5-525x, C5-525 & ZR525-CSi (954) 443-1100 www.jlaudio.com All specifications are subject to change without notice. JL Audio and the JL Audio logo, Stealthbox and the Stealthbox logo are registered trademarks of JL Audio, Inc. Ahead of the Curve and its respective logo is a trademark of JL Audio, Inc. JLA-SKU# 011343 01.22.2017 Printed in USA 2017 JL Audio, Inc. For more detailed information please visit us online at www.jlaudio.com. Page 7 JL Audio, Inc., 2017 1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y M I R A M A R, F L O R I D A 3 3 0 2 5 U S A