Krytox TM Product Brochure Contents 1. GeneralPurpose Oils and Greases 2. Special Extreme Pressure and Anticorrosion Greases 3. XHT(Extra High Temperature) Products. AUT (Automotive Lubricants) Series 5. Corrugator Krytox (HighTemperature Anticorrosion Greases) 6. Aerospace Grade Oils and Greases 7. H1 Food Grade Lubricants 8. Series for Reactive Gas Service 9. Vacuum Pump Fluids
1. GeneralPurpose Oils and Greases Oil Grades 100 101 102 103 10 105(H1) 106 107 Standard Grease Grades 200 201 202 203(H1) 20 205(H1) 206(H1) 207 Extreme Pressure Grease Grades 210 211 212 21 215 216 217 AntiCorrosion Grease Grades 220 221 222 223(H1) 22 225(H1) 226(H1) 227 ISO Grade of Oil 5 7 15 32 68 150 220 60 Estimated Useful Range < 70~ 66 < 9~ 150 < 70~ 10 < 9~ 220 63~ 132 81~ 270 60~ 15 76~ 310 51~ 179 60~ 355 36~ 20 33~ 00 36~ 260 33~ 500 30~ 288 22~ 550 Oil Viscosity, cst 20 (68) 0 (10) 100 (212) 20 (00) 260 (500) 12. 5.5 17. 7.8 2 38 15 3 82 30 5 177 60 8. 522 160 3.1 822 23 25.1 2. 1535 50 2 6 3.3 Oil Viscosity Index 29 92 111 12 13 15 Oil Pour Point <70 <9 <70 <9 <63 <81 60 76 51 60 36 33 36 33 30 22 Oil Density, g/ml 0 (32) 100 (212) 1.87 1.67 1.89 1.70 1.92 1.72 1.92 1.7 1.93 1.75 1.9 1.76 1.95 1.77 1.95 1.78 Max Oil Volatility, ASTM D2595 % in 22hr 121 (250) 20 (00) 90 75 35 7 3 1 7 <1 <3 <1 Oil Separation form Grease, ASTM D6 wt loss, % in 30hr 99 (210) 20 (00) 9 7 6 5 5 12 12 2
2. Special Extreme Pressure and Anticorrosion Greases Typical Properties Special Extreme Pressure and Anticorrosion Greases GPL 29 GPL 295 GPL 296 GPL 297 XHTEP298 XHTEP299 ISO Grade of Oil 68 150 220 60 720 1000 Estimated Useful Range 51~ 179 60~ 355 36~ 20 33~ 00 36~ 260 33~ 500 30~ 288 22~ 550 15~ 29 5~ 560 5~ 300 23~ 572 Oil Viscosity, cst 20 (68) 0 (10) 100 (212) 0 60 9 550 160 810 25 1600 0 2 2560 738 65 3500 1005 85 Oil Viscosity Index 12 125 13 155 158 166 Oil Pour Point 51 60 36 33 36 33 30 22 15 5 5 23 Typical Performance Pin and Vee Block Test Block on Ring Wear Test ASTM D3336 Bearing Life Test GPL 225,500 lb load = 37 inlb torque 0.70 mm wear scar GPL 295,500 lb load = 30 inlb torque 0.55 mm wear scar Greater than 3,200 hr at 177 (350) and 10,000 rpm Greater than 2,500 hr at 177 (350) and 10,000 rpm Timken EP tests were run on the following KRYTOX TM s by ASTM D2509: OK Load Score Load Scar Width at OK Load GPL 215 30 lb 0 lb 1.507 mm GPL 225 50 lb 60 lb 1.109 mm GPL 295 60 lb 70 lb 1.125 mm 3
3. XHT (Extra High Temperature) Products User Guide for Krytox XHT Greases Standard Grades XHTS and XHTSX 250~320 (82~608) Small or large bearings with relatively high speeds. Higher viscosity, lower evaporation of oil extends life. Anticorrosion Grades XHTAC and ACX 250~320 (82~608) For machines that run for shorter duration with frequent starts and stops Frequently cooled machines require anticorrosion additives. Extra Bonding Grades XHTBD, BDX, and BDZ 300~00 (572~752) For use when machine movement is not purely rotational. This is nonmelting for hightemperature use and offers better adhesion to substrate. Typical Properties Grade Thickener Viscosity (cst) Volatility (ASTM D97) Type Properties at 0 at 100 at 200 at 20 (%) Anticorrosion Additive XHTS PTFE Low friction max. temp. 300 500 7 6.9 <1 XHTSX PTFE Low friction max. temp. 300 738 60 8.8 <0. XHTAC PTFE Low friction max. temp. 300 500 7 6.9 <1 Sodium nitrite XHTACX PTFE Low friction max. temp. 300 738 60 8.8 <0. Sodium nitrite XHTBD Nonmelting Extra strong bonding to substrate 500 7 6.9 <1 XHTBDX Nonmelting Extra strong bonding to substrate 738 60 8.8 <0. XHTBDZ Nonmelting Extra strong bonding to substrate 1005 85 10.9 <0.3
. AUT (Automotive Lubricants) Series Formulations for Automotive Applications AUT 205 AUT 225 AUT 2A5 AUT 2E5 Additive free Traditional sodium nitrite anticorrosion additive Corrosion inhibited with proven soluble additive technology Sodium nitritefree anticorrosion additive Typical Properties of the Krytox AUT Series Appearance Creamy Consistency Estimated Useful Temperature Range to 200 (7 to 392) Base Oil Viscosity, cst 20 (68) 310 0 (10) 100 100 (212) 12.5 200 (392) 2.5 Oil Separation, wt% after 30hr 99 (210) Max. Oil Volatility, % in 22hr, ASTM D2595 66 (150) 0.1 121 (250) 0.5 20 (00) 2 Dropping Point Standard NLGI Grade 2 Specific Gravity at 0 (32), g/cm 2.0 5
5. Corrugator Krytox (HighTemperature Anticorrosion Greases) Typical Properties Corrugator Krytox 226 FG 227 FG ISO Grade of Base Oil 220 60 Estimated Useful Range Oil Viscosity, cst 0 (10) 100 (212) 36~ 260 33~ 500 25 30~ 288 22~ 550 0 2 Specific Gravity 1.95 1.95 Oil Separation, %, 30hr at 99 (210) 3 3 Appearance texture texture Anticorrosion Additive Sodium Nitrite Sodium Nitrite Antirust Rating, ASTM D173 Pass Pass Four Ball Wear Scar, ASTM D 2266 at 1 hr, 1200 rpm, 107(225), 20kg 0.mm 0.mm Coefficient of Friction, ASTM D 2266 0.11 0.11 Oil Volatility, %, 22 hr at 20(00) ASTM D 972 (Modified) 3 max. 1 max. 6
6. Aerospace Grade Oils and Greases Typical Properties (Oils) Aerospace Oil Grade Property ASTM Test Method Test Conditions Units 13AZ 13AA 13AB 13AC 13AD Average Molecular Weight NMR 2060 2210 3800 590 780 Viscosity ASTM D5 32 (25) 0 (32) 20 (68) 38 (100) 0 (10) 99 (210) 100 (212) 20 (00) 260 (500) cst 780 228 60 2.7 22.8.2.1 1.1 12,30 350 88 35 32 5. 5.3 1.3,620 1070 86 78 10.5 10.2 2.1 390 800 270 23 26 25..1 2. 7500 150 502 50 2. 6.0 3. Viscosity Index ASTM D2270 60 96 113 13 16 Pour Point ASTM D97 55 70 50 60 0 0 35 30 30 20 Distillation Range ASTM D1160 53 Pa (0. ) 10 / 210 285 / 10 170 / 25 30 / 75 215 / 290 20 / 555 260 / 370 500 / 700 300 / 00+ 570 / 750+ Oil Density 0 (32) 100 (212) g/ml 1.91 1.72 1.92 1.7 1.93 1.75 1.95 1.77 1.95 1.78 Vapor Pressure Knudsen 38 (100) 260 (500) 38 (100) 260 (500) Kpa Kpa x 10 1.5 5 x 10 5 0.2 1 x 10 0.8 1 x 10 5 0.1 5 x 10 6 3 x 10 2 7 x 10 7 x 10 3 8 x 10 8 2 x 10 3 1 x 10 8 3 x 10 6x10 9 3 x 10 8 x 10 10 x 10 5 Volatility ASTM D2595 19 (300) 20 (00) 260 (500) wt% loss In 22 hr 15 1.9 17.3 76.2 <1 2 Estimated Useful Range 57~19 70~300 51~177 60~350 0~232 0~50 3~288 30~550 29~316 20~600 7
6. Aerospace Grade Oils and Greases Typical Properties (Greases) Property ASTM Test Method Test Conditions Units Aerospace Grade Aerospace Grease Grade AZ (H1) AA AB (H1) AC (H1) AD Extreme Pressure Grade 250AZ 250AC 250AD Rust Inhibited Grade 280AB 280AC 283AZ 283AA 283AB 283AC 283AD Viscosity of Base Oil ASTM D5 20 (68) 38 (100) 99 (210) 20 (00) cst 60 2.7.2 1.08 88 35 5. 1.3 86 10.5 2.1 800 270 26.1 150 502 6.0 Vapor Pressure of Base Oil Knudsen 38 (100) 260 (500) x 10 1.5 1 x 10 0.8 5 x 10 6 8 x 10 8 6x10 9 3 x 10 2 2 x 10 3 3 x 10 Volatility of Base Oil ASTM D2595 19 (300) 20 (00) 260 (500) wt% loss In 22 hr 15 1.9 17.3 76.2 <1 2 Pour Point of Base Oil ASTM D97 55 70 50 60 0 0 35 30 30 20 Penetration ASTM D217 60 Strokes 265~295 Mechanical Stability ASTM D217 10,000 and 100,000 Strokes No change from original grade Oxidation Stability ASTM D92 99 (210 ) 0 psig O 2 pressure drop after 600 hr Liquid Oxygen Impact ASTM D2512, SA MSFC 106B Pass Grease Density 25 (77 ) g/ml 1.89 1.91 1.92 1.93 1.93 Oil Separation ASTM D6 99 (210 ) 20 (00 ) wt% loss In 30 hr 6 5 20 12 3 11 3 10 Estimated Useful Range 57~19 70~300 51~177 60~350 0~232 0~50 3~288 30~550 29~316 20~550+ 8
7. H1 Food Grade Lubricants Typical Properties (Greases) General Greases FG 20 FG 22 FG 2 FG 26 Anticorrosion Greases FG 30 FG 32 FG 3 FG 35 FG 36 NLGI Grade 2 2 2 2 2 Base Oil Viscosity, cst at 0 (10) 30 160 500 738 Viscosity Index 121 125 13 19 158 Operating Range, () 60 to 15 ( 76 to 310) 36 to 20 ( 33 to 00) 30 to 260 ( 22 to 500) 20 to 300 ( to 572) 10 to 300 (1 to 572) Typical Properties (Oils) Oils FG 0 FG 5 FG 50 FG 53 Antirust No No Yes Yes Oil Viscosity, cst 0 (10) 100 (212) 160 500 2 160 215 23 Volatility at 22 hr 20(399) = 3% 260(500) = 2% 20(399) = 3% Not tested Viscosity Index 125 133 125 131 Pour Point, () 35 (31) 25 (13) 35 (31) 30 (22) Upper Use Limit, () 200 (392) 275 (527) 0 (356) 295 (563) Vapor Pressure 7 x 10 7 1 x 10 9 7 x 10 7 Density, g/cc at 20(68) 1.92 1.93 1.92 1.92 9
8. Series for Reactive Gas Service Typical Properties Product Properties 8900 890 8906 8906A 8908 8950 8990 PLSS 8805 Description Light gray, paste Clear, colorless oil NLGI Grade 2 2 2 2 2 1.5 1 2 Thickener PTFE PTFE PTFE PTFE inorganic Nonmelting PTFE PTFE Estimated Useful Temperature Range, 51 ~ 121 51 ~ 179 36 ~ 260 36 ~ 200 0 ~ 0 15 ~ 325 75 ~ 150 36 ~ 260 0 ~ 160 Oil Viscosity, Kinematic cst ASTM D5, 0 100 20 1.8.7 60 9 25 25 9 7.2 500 7 15 3.7 25 3.9 81 11 Oil Density, g/ml 1.9 1.93 1.95 1.95 2.0 1.95 1.9 1.95 1.9 Max Oil Volatility, % in 22 hr ASTM D972, 66 121 20 260 9 35 1 3 1 <5 1 <6 2 <1 2.1 8 1 <5 1 10
8. Vacuum Pump Fluids Typical Properties (Oils) Krytox Property Test Method Conditions Units 1506 / 1506XP 151 / 151XP 1525 / 1525XP 1531 / 1531XP 16256 165 Average Molecular Weight NMR 2160 280 370 390 900 Vapor Pressure Knudsen 20 (68) 50 (122) 100 (212) 200 (392) x 10 7 1 x 10 5 1 x 10 3 5 x 10 1 2 x 10 7 3 x 10 6 1 x 10 1 x 10 2 1 x 10 7 1 x 10 6 3 x 10 5 2 x 10 3 1 x 10 7 1 x 10 6 3 x 10 5 2 x 10 3 3 x 10 1 2 x 10 12 1 x 10 9 2 x 10 6 5 x 10 12 Kinematic Viscosity ASTM D5 20 (68) 50 (122) 100 (212) mm 2 /s (cst) 60 15.5.1 10 32 7.2 250 52 10.6 310 63 12.5 2560 37 6.6 50 Density 20 (68) 50 (122) 100 (212) 200 (392) g/cc 1.88 1.82 1.73 1.5 1.89 1.83 1.7 1.55 1.90 1.8 1.75 1.56 1.90 1.8 1.75 1.56 1.92 1.87 1.78 1.61 Pour Point ASTM D97 () 60 (76) 5 (65) 8 (5) 1 (2) 15 (5) 35 (31) Distillation ASTM D1160 10% () 160 (320) 200 (392) 200 (392) 200 (392) Range at 0. 90% 220 (28) 280 (536) 300 (572) 300 (572) Heat of Vaporization Knudsen 150~250 (302~82) cal/g 9 7 6 6 Volatility at 22 hr ASTM D2595 121 (250) % 6.5 1.3 0.6 0. 0.2 Surface Tension 25 (77) dyn/cm 17 19 19 19 Food Contact Approval F H1 / No F H1 / No F H1 / No None None None 11
8. Vacuum Pump Fluids Typical Properties (LVP_Low Vapor Pressure) Krytox (Grease) Property Conditions Units LVP Penetration worked, 25 (77) mm/10 280 NLGI Consistency 2 Vapor Pressure 20 (68) 200 (392) 20 (68) 200 (392) kpa kpa < 1.0 x 10 13 < 1.0 x 10 5 < 1.3 x 10 1 < 1.3 x 10 6 Oil Separation 30 hr, 20 (399) wt% 13.8 Evaporation Loss 22 hr, 20 (399) wt% 0.3 Density 25 (77) g/cc 1.9 Typical Vapor Pressure Temperature Characteristics 12