Stainless steel housing type Series IP69K: Highly water resistant Tough structure for food processing line needs washing with high temperature and high pressure water. Achieves long sensing distance. For production line needs washing Selection table Type Sensing distance Part number Through beam Retro reflective Diffuse For production line with detergent splash BGS on another page Part number of PNP type has suffix P : Accessories For meat and fresh food processing line Reflector for retro reflective type Sensing distance:.~5.5m Wall mounting bracket Sensing distance:.5~m Protective mounting bracket mm thick SUS bracket Sensing distance:.5~.5m
IP69K protection 9 6 5mm IP69K is an rating of German standard DIN 5-9 extends the IEC 659 rating system for high-pressure, hightemperature wash-down applications. Test condition: A sensor on the turn table that rotates 5 times per minutes. Pressure: 8~bar Flow rate: ~6 litre/minute Temperature: +8 * IP69K doesn t mean to guarantee that the sensor works under the test condition above. The sensor won t work correctly when the lens gets wet and the light is refracted. High-pressure, high-temperature, detergent wash-down resistant Tough structure Top cover: Poly Ether Sulphone (PES) Oil, detergent, high-temperature resistant. Top level protection in transparent plastic. SW, Pot: Poly Ether Etherketone (PEEK) Shock, scratch, stress, heat resistant. Highly resistant to chemical except concentrated sulfuric acid. Housing: SUS6L Highly corrosion-resistant. Detergent, bactericide resistant. Printing by laser marking There is no label attached so you don t have to care about interfusion into foods of the label unsticked. Lens PPSU for thru-beam, diffuse type Chemical, heat resistant. Very stable material. Lens PMMA with SiO coating for retro reflective type Oil, scratch resistant. Water repellent and anti-static. Gasket (FKM), cable (PVC) Chemical, oil resistant and flexible. Longest sensing distance in the class High brightness LED by element enables longest sensing distance in the class. element LED (A InGaP-LED) Through beam type Sensing distance: m Retro reflective type Sensing distance: 5.5m Diffuse type Sensing distance: 8mm
Specifications Type Through beam Retro reflective Part number Sensing distance Light source Spot size Response time Hysteresis Sensitivity adjustment Indicator Control output Operating mode Cable Power supply Power consumption Conformity Operating temp./humid. Environmental illuminance Vibration resistance Shock resistance Protection category Material Weight Diffuse ZT-MN ZR-M55N ZD-M8N m.~5.5m ~8mm element red LED φmm at m φ mm at 5.5m 5μs max. φmm at 8mm - - % max. turn potentiometer Red LED: output, Green LED: stable, Emitter of thru-beam type doesn t have indicator NPN (PNP) Open collector, Max.mA/DCV Light ON/Dark ON selectable by switch Cable length: m, φ DC~V including % ripple Emittor:5mA max. Receiver:5mA max. 8mA max. 8mA max. CE Feilen Level -5~+55 no condensation / 5~85%RH Sunlight:, lux max. Incandescent lamp:, lux max. ~55Hz double amplitude.5mm,,z hours G (m/s ),,Z times IEC :IP67 IEC :IP67 IEC :IP67 DIN :IP69K DIN :IP69K DIN :IP69K Reflector is IP67 Housing: SUS6L Housing: SUS6L Housing: SUS6L Top cover: PES Top cover: PES Top cover: PES Lens: PPSU Switch, Pot: PEEK Lens: PMMA Switch, Pot: PEEK Lens: PPSU Switch, Pot: PEEK Cable: PVC Cable: PVC Cable: PVC Gasket: FKM Gasket: FKM Gasket: FKM Approx. g excluding cable Accessory Mounting bracket:bef-wb Mounting bracket:bef-wb Mounting bracket:bef-wb Reflector: V-6. With V-6. With mm x mm white paper
Input/Output Diagrams NPN type PNP type Brown DC ~V Brown DC ~V Load Protection Main circuit Black Control output Main circuit Black Control output Protection Load Blue V Blue V Through beam emitter Main circuit Brown DC ~V Notes When using switching regulator for power supply, please connect frame ground to earth ground. Wiring close to high voltage or power line to motors may cause malfunction because of inductive noise. Please wire separated from those lines. Please wait around msec before use sensor output after power up. Blue V
Dimensions Sensor - Through beam Emitter Unit: mm - Through beam Receiver - Diffuse type - Retro reflective type.9 6.6 Sensitivity adjustment pot. Red LED: output Green LED: stable Switch Light ON / Dark ON.. 5. -M, Torque:.5Nm max. B A.6 φ Type Through beam Diffuse Retro reflective A Light axis B Light axis 9.6 9.6. 9. 9.6 Reflector V-6 Bundled with retro reflective type V- P5A φ7 φ.5 5.9 6.9 5 5 5. 5 5.9. 6 8.5.. - φ.6 5 5.5 8 8.. 6..
Mounting bracket BEF-W-B Bundled with sensor BEF-W-A -R. 7..5 5.7 6. Unit: mm -R. 9.. -R 9 8-R.6 5. -R -R 6. 9.7 9..6 5. 7. 5.8 7. 5-R. 5. 5.. 9.7 -R. 8. -R.6 9 Protective mounting bracket LK-S LK-S 6.5 8 6 7 6. 9 6. 9 Light axis A 5 Light axis A 7 6.5 8 65 Type Through beam Diffuse Retro reflective A Light axis 6.6 9.
Typical characteristic data ZT-MN 8 6 6 8 5 5 5 5 5 ー 5 5 5 5.6....8.6.. 5 ZR-M55N 8 6 P5A V- V-6 V-6 P5A V- 5 6 7 6 8 5 6 7 8 9 8 ー 7 6 5 (V-6) (V-) (P5A) 8 ー ー 7 6 5 5 5 V-6 5 5 P5A V- 6 8
ZD-M8N 5 5 9% ( mm ) 8% ( mm ) 5 6% ( mm ) 5 5 6 8 5 9 % ( mm ) 6 8 Spot size (mm) 8 7 6 5 5 6 7 8 9 6 8 6 6 8 9 % 9%: White paper 8%: Gray paper 6%: Black paper