ELECTRONICS TRANSFORMERS SWITCHING POWER SUPPLIES

ELECTRONICS TRANSFORMERS SWITCHING POWER SUPPLIES 7000 SERIES A fully ertified range of PCB mounting Power supplies from 1 W up to 10 W myrra.om

Presenting the Eletroni Transformers miniature power supplies at your fingertips Enhaned effiieny, performane & flexibility all in existing formats EI30 / EI38 / EI8 full ertifiation from global authorities Enapsulated Power Supplies 2.5W, 5W, 7.5W & 10W Regulated, unregulated, single & dual output voltage families Serie 7000 Filtering Transformer 26,7 mm 85-265V AC or DC Control IC Load 21,8 mm Retifier Swith & Control Retifier & Filtering 31,7 mm + s FI s N D DVE K EMA EUR EUR EN 61558-2-6 EN 60950

ELECTRONIC TRANSFORMERS MYRRA enapsulated eletroni transformers are Swithed Mode Power Supplies based on Flybak topology. They onstitute an interesting alternative to the traditional supply in the most ommon appliations of power lower than 10W. ENERGY SAVING due to high effiieny and low standby power The appliations for the Eletroni serie are: o Alternative to the linear transformers in all AC/DC appliations of power up to10w o Alternative to DC/DC onverters for appliation in D.C.urrent (Teleom supplies, eletri substations et.) o Industrial, domesti and onsumer eletronis appliations o Standby devies and others DC or AC auxiliary supplies With the same footprint as a EI30 transformer, they will replae: - 50 Hz Transformer - Fuse - Bridge Retifier - Filtering Capaitor Regulated types will also replae linear regulator and heatsink MAIN FEATURES o Wide input voltage range o Inreased power. 3 x ompared to standard EI30 - EI38 - EI8 transformers o Better energeti effiieny: 70% typial ompared to 0% for the onventional supply o Very low Standby Power onsumption: meets requirements of Energy Star or EC Code of Condut o Same footprint as EI30 - EI38 - EI8 transformer : Upgrade your appliation without redesign of PCB SAFETY STANDARDS Meets all requirements of: o EN 60950 o EN 60335 o EN 61558-2-16 o EN 61558-1 o UL 60950-1 o CSA 22.2 N 60950-1 o UL 9-V0 EMC STANDARDS Conduted and radiated emissions onform to o EN 5501-1 o EN 55022 lass B 1 Immunity onform to o EN 5501-2 o EN 61000--x

ONE OUTPUT 2.5 & 5W - Regulated ELECTRICAL SPECIFICATIONS Input voltage range 85 to 265 Volts AC 120 to 370 Volts DC Input Frequeny 7 to 63 Hz voltage auray (full load ) ± 2% Line output voltage variation ± 0.3% Load output voltage variation ± 0.5% No load input power < 200mW Energy onsumption and effiieny : Meets requirements of Energy Star and EC Code of Condut SAFETY Prepared for Class II reinfored insulation Input / Isolation test voltage: 000 Va Operating ambient temperature: - 25 C / + (See table) Storage temperature: - 0 C / + 85 C Input protetion by integrated fusible resistor short iruit protetion: automati restarts when fault ondition is removed Thermal shutdown with automati reovery if internal temperature exeeds allowable value Referene voltage urrent Power (W) Effiieny (%) 7121 3.3 750 2.5 65 +70 7122 5 550 2.75 68 +70 7123 9 270 2.5 72 +70 712 12 210 2.5 7 +70 7125 15 170 2.5 75 +70 7126 2 110 2.5 77 +70 7151 3.3 1350.2 65 +50 7157 3.8 1180.5 66 +50 7152 5 900.5 68 +50 7153 9 550 5 72 +50 715 12 20 5 75 +50 7155 15 320 5 76 +50 7156 2 220 5 79 +50 * Note: ustom options available DIMENSIONS and PINOUT pins pins 1 & 5 : AC or DC Input pin 7: DC output +V pin 9: DC output 0V view from pins side): 2

ONE OUTPUT 3.2 & 5W - Non Regulated ELECTRICAL SPECIFICATIONS Input voltage range 85 to 265 Volts AC 120 to 370 Volts DC Input Frequeny 7 to 63 Hz voltage auray (full load) ± 5% Line output voltage variation ± 3% Load output voltage variation ± 5% No load input power < 300mW Energy onsumption and effiieny : Meets requirements of Energy Star and EC Code of Condut SAFETY Prepared for Class II reinfored insulation Input / Isolation test voltage: 000 Va Operating ambient temperature: - 25 C / + (See table) Storage temperature: - 0 C / + 85 C Input protetion by integrated fusible resistor short iruit protetion: automati restarts when fault ondition is removed Thermal shutdown with automati reovery if internal temperature exeeds allowable value Referene voltage urrent Power (W) Effiieny (%) 711 12 200 2. 7 +70 7132 5 500 2.5 +70 7133 9 360 3.2 73 +70 713 12 270 3.2 75 +70 7135 18 180 3.2 78 +70 7136 2 130 3.2 80 +70 7163 9 560 5 * 73 +50 716 12 20 5 * 75 +50 7166 2 210 5 * 80 +50 * Note: Power up to 5.W is possible with input voltage 97 Va DIMENSIONS and PINOUT pins pins 1 & 5 : AC or DC Input pin 7: DC output +V pin 9: DC output 0V 3

TWO OUTPUTS - COMMON & ISOLATED 3 to 5W - Regulated ELECTRICAL SPECIFICATIONS Input voltage range 85 to 265Volts AC 120 to 370V DC Input Frequeny 7 to 63 Hz voltage auray : see table for 10 to 100% rated load of eah output (inludes line and load variations) No load input power < 200mW Energy onsumption and effiieny : Meets requirements of Energy Star or EC Code of Condut SAFETY Prepared for Class II reinfored insulation Input / Isolation test voltage: 000 Va Operating ambient temperature: - 25 C / + (See table) Storage temperature: - 0 C / + 85 C Input protetion by integrated fusible resistor short iruit protetion: automati restarts when fault ondition is removed Thermal shutdown with automati reovery if internal temperature exeeds allowable value Referene 723 72 725 726 727 1 2 +10.5 +7 + 15 +7 +12 +5.5 +5 +12 +15-15 1 2 380 max 100 max 300 max 70 max 130 max 300 max 00 (600max) 170 max 130 max 130 max COMMON OUTPUT Power (W) * Nota: Power up to 5W is possible with input voltage 97 Va and 50 C * * 3.2 1 2 auray ± 3% +15% ± 3% ± 5% ± 10% ± 3% ± 8% ± 8% Effiieny (%) 72 +60 73 +60 65 +70 65 +60 73 +60 DIMENSIONS and PINOUT 5 pins pins 1 & 5 : AC or DC Input pin 6: Common output 0V pin 7: DC output 1 pin 10: DC output 2 The 2 outputs share a ommon 0v referene. This enables loser oupling and a better rossregulation of the outputs (view from pins side): ISOLATED OUTPUT Referene 7252 725 7255 7257 7258 1 2 5 5 12 12 15 15 5 12 18 8 1 2 350 (600max) 350 max 165 (300max) 165 max 135 (200max) 135 max 00 (600max) 170 max 150 (200max) 150 max Power (W) 3.5 1 2 auray ± 3% +15% ± 5% ± 5% ± 3% ± 5% Effiieny (%) 66 +60 72 +60 73 +60 68 +60 72 +60 DIMENSIONS and PINOUT 6 pins pins 1 & 5 : AC or DC Input pin 6: DC output1 0V pin 7: DC output1 +V pin 9: DC output2 0V pin 10: DC output2 +V 2 isolated outputs - 1 only is regulated and should provide the higher power 1 / 2 isolation : 000Va (view from pins side):

ONE OUTPUT 7,5W - Regulated ELECTRICAL SPECIFICATIONS Input voltage range 85 to 265 Volts AC 120 to 370 Volts DC Input Frequeny 7 to 63 Hz voltage auray full load (see table) Line output voltage regulation ± 0,5% Load output voltage regulation (see table) No load input power < 150mW Energy onsumption and effiieny : Meets requirements of Energy Star and EC Code of Condut SAFETY Prepared for Class II reinfored insulation Input / Isolation test voltage: 000 Va Operating ambient temperature: - 25 C to (see table) Storage temperature: - 0 C / + 85 C Input protetion by integrated fuse short iruit protetion : automati restarts when fault ondition is removed Thermal shutdown with automati reovery if internal temperature exeeds allowable value Referene voltage auray Power (max W) Load output voltage regulation Effiieny (%) @230VAC 7206 3.3 2270 ± 3% 7.5 ± 3% >7 +70 7200 5 1500 ± 2% 7.5 ± 1% >76 +70 7201 9 830 ± 2% 7.5 ± 1% >80 +70 7202 12 625 ± 2% 7.5 ± 1% >82 +70 7203 15 500 ± 2% 7.5 ± 1% >82 +70 720 18 20 ± 2% 7.5 ± 1% >82 +70 7205 2 310 ± 2% 7.5 ± 1% >82 +70 Note: other output voltages are available upon request DIMENSIONS and PINOUT pins Pins 1 &5 : AC or DC Input Pin 7 : DC output + V Pin 9 : DC output OV 35.0 ±0.5 0.8 10.0 ±0.5 7 9 5 1 20 ±0.5 1.0 ±0.5 25 ±0.5 2.5 ±0.5.0 ±0.5 7.5W Regulated view from pins side) 5

ONE OUTPUT 10W - Regulated ELECTRICAL SPECIFICATIONS Input voltage range 85 to 265 Volts AC 120 to 370 Volts DC Input Frequeny 7 to 63 Hz voltage auray full load (see table) Line output voltage regulation ± 0,5% Load output voltage regulation (see table) No load input power < 100mW Energy onsumption and effiieny : Meets requirements of Energy Star and EC Code of Condut SAFETY Prepared for Class II reinfored insulation Input / Isolation test voltage: 000 Va Operating ambient temperature: - 25 C to (see table) Storage temperature: - 0 C / + 85 C Input protetion by integrated fuse short iruit protetion : automati restarts when fault ondition is removed Thermal shutdown with automati reovery if internal temperature exeeds allowable value Referene voltage auray Power (max W) Load output voltage regulation Effiieny (%) @230VAC 7216 3.3 3000 ± % 10 ± % >76 +50 7210 5 2100 ± 3% 10 ± 3% >76 +60 7211 9 1100 ± 2% 10 ± 1% >79 +60 7212 12 830 ± 2% 10 ± 1% >80 +60 7213 15 670 ± 2% 10 ± 1% >80 +60 721 18 560 ± 2% 10 ± 1% >80 +60 7215 2 20 ± 2% 10 ± 1% >80 +60 Note: other output voltages are available upon request DIMENSIONS and PINOUT pins Pins 1 &5 : AC or DC Input Pin 7 : DC output + V Pin 9 : DC output OV 0.0 ±0.5 0.8 15.0 ±0.5 7 9 5 1 25.0 ±0.5 8.0 ±0.5 27.5 ±0.5 26.0 ±0.5.0 ±0.5 10W Regulated view from pins side) 6

OTHER PRODUCTS PCB MOUNTING TRANSFORMERS Enapsulated Transformers 50 / 60 Hz (000 and 5000 series) Full range of standard produts up to 60VA Safety isolating appliation Global ertifiation VDE, UL/CSA, EN61558, UL-9V0, RoHs Fully automated prodution testing -100% Ferrite ore transformers and indutors (700 series) Large range of appliations: Flybak Transformers, CM hokes... et Conforming to international standards Standard produt and ustomised design available INDUCTORS - THROUGH HOLES & SMD TYPE POWER RANGE: TRANSFORMERS / FILTERS / INDUCTORS 50Hz & HF Tehnology (30000 series) Customised design against performane speifiation Conformane with international standards UL, IEC, CSA up to 200KVA and 1000V systems Toroidal Transformers (60000 series) Custom design produt Power Rating up to 30 KVA Conforms with Internatioanl standards EN-61558, CE

7000 SERIES myrra.om