DRAFT August, 04 3:56 PM SERIES 7000/8000 3 PIECE FULL PORT 4-7000 - 36SS 8000 - WCB
7000/8000 SERIES BALL VALVES Flow-Tek s Series 7000 and 8000 ball valves offer the highest flexibility in selection of end connections, seat materials and 3 piece design. To meet customer demands for a valve with the widest possible range of applications, these valves can be fitted with control or tri-ported balls (for full cavity drainage), as well as cavity fillers for special service requirements. The Series 7000/8000 is designed with extensive interchangeability of balls, stems, stem packing, handles and mounting hardware between valve sizes and series members. This system reduces parts inventory and maintenance costs. The 3 piece body design allows the body to swingout for ease of in-line maintenance. It also makes it possible to offer a wide variety of end connections. BALL - Flow-Tek balls are solid metal, precision machined and mirror finished for bubble-tight shut off with less operating torque. Ball edges have machined curvatures to reduce seat wear and provide a high cycle life. BODY - Valve bodies are investment cast and solution annealed/ normalized for the highest quality and added strength. Body castings are marked with a foundry heat number for full traceability. Carbon steel bodies are phosphate coated for increased corrosion resistance. SEAT - Flow-Tek s seat design ensures bi-directional, bubbletight sealing while providing the lowest possible torque. This seat design reduces friction, minimizes seat wear and reduces operating torque. SEAT MATERIALS - Flow-Tek offers the following standard seat materials for the Series 7000/ 8000: RPTFE, TFM-600, Stainless Steel/PTFE (50/50), UHMWPE, Virgin PTFE, Tek-Fil, and Cavity Fillers. Other seat materials are available. DOUBLE LOCK NUT DESIGN - Standard on the Series 7000/8000, the double lock nuts allow handles to be easily and safely removed while the valve is under full line pressure. LIVE-LOADED STEM SEALS - The live-loaded stem seals considerably increase the number of cycles between maintenance adjustments. BODY HINGES - Heavy duty hinges, throughout the entire size range, provide positive alignment of body to end connection during swing-out, in-line servicing. END CONNECTIONS - Full range of interchangeable connections. BODY BOLTS - Standard material is 304 Stainless Steel.
Stem Nut and Tab Lock Washer Belleville Washers Packing Gland PEEK Protector Stem Packing Tek-Fil Thrust Washer PEEK Protector Anti-Static Devices ANTI-STATIC PROTECTION - Series 7000/8000 valves feature anti-static grounding devices as standard. These devices ensure electrical continuity between valve ball, stem and body, thus eliminating the possibility of static electrical charges creating sparks within the valve. STEM ASSEMBLIES - Flow-Tek manufactures heavy duty, high quality stems with double D connection to ball and operator mounting. Stems are mated with the ball to ensure positive contact. All Flow-Tek stems are internal entry and blowout proof for maximum safety. STEM DESIGN FOR 3 VALVES - The stem is guided by the valve body and the gland, ensuring smooth operation even in high torque service. The packing gland is adjustable and all stems are polished to reduce torque. Optional belleville washers can be added for a self-adjusting, live load. STEM PACKING - An adjustable V-ring design creates a multiple seal between the stem and body. Each stem assembly is composed of three or four (dependent on valve size) rings providing a very high cycle life by resisting creep and cold flow. The Thrust Washer and the Thrust Washer Protector combine to provide a primary seal, reduce torque and prevent galling. This arrangement is a Flow-Tek exclusive. SMART STEM - Valve Sizes 4 through Flow-Tek s interchangeable family of valves feature strong, large diameter stems with live-loaded, self-adjusting sealing utilizing belleville washers which automatically adjust to compensate for changes in temperature and wear. Manual adjustments which can cause damage to the seal and seat are not required. The assembly is secured by a saddle-type lock washer which prevents stem nuts from unthreading in high cycle automation applications. PRESSURE / TEMPERATURE Pressure (psi) 00 000 800 600 400 00 0-50 0 50 00 50 00 50 Temperature ( F) 300 350 400 450 500 550 /4-4 Valves: RPTFE/TFM /4-4 Valves: UHMWPE /4-4 : 50/50 SS Filled TFE 6 - Butt Weld Valves: RPTFE ASME Class 50 Flanges /4" - 4" Valves: Tek-Fil NOTE: Series 8000 carbon steel valves are limited to -0 F. 3
8 6 9 5 9 8 5 4 4 3 9 5 4 6 3 6 4 Extended Butt Weld End Connection ITEM/NAME Body 8 7 COMPONENTS AND MATERIALS 4 to STAINLESS ASTM A35 CARBON ASTM A6 ASTM A35 ASTM A6 End Cap 3 Ball ASTM A35 4 Seat 5% RPTFE 5 Stem ASTM A479 Type36 6 Body Seal TFM 7 Spring Washer SS304 8 Body Nut SS304 9 Body Bolt / Stud SS304 4 0 Anti-Static Device SS36 Protector PEEK QTY. ITEM/NAME Socket Weld End Connection Note: Other End Cap connections are available. STAINLESS CARBON Thrust Washer TEK-FIL 4 Stem Packing 5% RPTFE 3 5 Packing Gland Sleeve SS304 8 Belleville Washer SS30 9 Lock Washer SS304 3 Travel Stop Set Sleeve SS304 4 Travel Stop Bolt SS304 5 Handle SS304 6 Lock Nut SS304 8 Handle Sleeve Vinyl 9 Locking Device SS304 QTY. Weld Ends use CF3M Number of Nuts and Spring Washers: 4 to Valves 4 Valves 8 4
SPECIFICATIONS Valve Sizes /4 through Design meets MSS-SP-0. Threaded End Connections meet ASME B.0. NPT. Socket Weld End Connections meet ASME B6.. Butt Weld End Connections meet MSS SP-7 /ASME B6.5. Flanged End Connections meet ASME Class 50. Valve body and end cap connections are high quality investment cast and solution annealed/ normalized. Body and end cap wall thickness meets ASME B6.34. Valve stems are blow-out proof for maximum safety and meet ASME B6.34 specification. 6 5 4 5B 0 7 5A All valves are factory tested to MSS SP-7 and API 598. Flow-Tek offers the seat, body seal, thrust washer and stem packing as recommended spare parts. These parts are available as a packaged repair kit. 4B 4A 5 4A 4B 9 3 9 COMPONENTS AND MATERIALS 3 - ITEM / NAME STAINLESS ASTM A35 Body ASTM A35 End Cap CARBON ASTM A6 ASTM A6 3 Ball ASTM A35 4A Seat 5% RPTFE 4B Seat Support ASTM A35 ASTM A6 QTY 5 Stem ASTM A479 Type36 6 Body Seal PTFE 9 Body Bolt SS304 * 0 Anti-Static Device SS36 Protector PEEK Thrust Washer TEK-FIL 3 Stem Bearing 5% RPTFE ITEM / NAME STAINLESS CARBON QTY 4 Stem Packing 5% RPTFE 3/4 5 Packing Gland SS304 Carbon Steel 6 Packing Follower ASTM A35 ASTM A6 7 Gland Bolt SS304 Carbon Steel 0 Stop Housing ASTM A35 ASTM A6 Housing Bolt SS304 Carbon Steel 4 Travel Stop SS304 Carbon Steel, Zinc Plated 5A Handle Ductile Iron/Carbon Steel 5B Handle Junction Ductile Iron Ductile Iron 7 Handle Bolt Carbon Steel Carbon Steel 30 Snap Ring Nickel Plated Carbon Steel Weld Ends use CF3M Seat Supports for 6 and larger valves * Number of Studs: 3 4 Valves... 6 Nuts & Spring Washers... Number of Body Bolts: 6 Valves 0 0 Valves 3 8 Valves 4 Valves 40 5
SERIES 7000 & 8000 DIMENSIONS /4" " VALVES (8mm - 300mm) D D D C C C C C C øb ø B ø B A A A /" / " VALVES 3" 4" VALVES 6" " VALVES Ux4 K Ux4 K SECURE MOUNT øp H M øp H M J L J /4" / " VALVES 3" " VALVES L DIMENSIONS Models 7000 (36SS) / 8000 (WCB) A SIZE øb C C D H J K L M P INCHES MILLIMETERS NPT, SW, BW FLG Extended SW Extended BW /4.84 0.37.60.54 6.50.7.7 0.3 0.55 0.5 0.37 0-4 3/8.84 0.50.60.54 6.50.7.7 0.3 0.55 0.5 0.37 0-4 /.84 4.39 0.04 9.04 0.59.60.54 6.50.7.7 0.3 0.55 0.5 0.37 0-4 3/4 3.35 5.80 0.43 9.30 0.79.9.66 6.50.7.7 0.3 0.55 0.5 0.37 0-4 3.6 5.97 0.7 9.48.00 3.43.05 7.87.39.39 0.43 0.75 0.3 0.43 /4-0 4 4.33. 9.84.6 3.6. 7.87.39.39 0.43 0.75 0.3 0.43 /4-0 4.84 8.03.78 0.8.50 4.3.60 9.84.95.95 0.55 0.9 0.37 0.6 5/6-8 5.59 9.04.48 0.73.00 4.53.95 9.84.95.95 0.55 0.9 0.37 0.6 5/6-8 7.6.00.56 5.04 3.39 9.84.84.84 0.69.4 0.47 0.75 5/6-8 3 7.95 0.0.00.99 6.4 3.7 5.35 3.54.87.75 3.07 0.67.0 /-3 4 9.06 3.90.00 4.0 7.087 4.35 5.35 3.54.87.75 3.07 0.67.0 /-3 6 8.00 5.50 5.98. 7.7 43.3 3.38 3.38.65 3.54.0.7 /-3 8 0.50 8.00 7.87 3.50 8.47 43.3 3.38 3.38.65 3.54.0.7 /-3 0.00.00 9.84 4.69 9.96 43.3 4.53 4.53.97 3.78.38.7 5/8-5.00 4.00.8 6.6.54 43.3 4.53 4.53.97 3.78.38.7 5/8-8 7. 9.5 66 39 65 9.7 9.7 8 4 6.4 9.3 0-4 0 7..7 66 39 65 9.7 9.7 8 4 6.4 9.3 0-4 5 7..5 54.9 9.5 5 66 39 65 9.7 9.7 8 4 6.4 9.3 0-4 0 85 47. 64.8 36. 0 74 4. 65 9.7 9.7 8 4 6.4 9.3 0-4 5 9 5.7 7.9 40.7 5.4 87 5 00 35.7 35.7 9 8 0.9 /4-0 3 0 84.8 49.8 3 9 56 00 35.7 35.7 9 8 0.9 /4-0 40 3 04 99. 6 38 05 66 50 49.5 49.5 4 3 9.5 5.7 5/6-8 50 4 9.6 37 7.6 50.8 5 75 50 49.5 49.5 4 3 9.5 5.7 5/6-8 65 84.5 304.8 65 8 86 50 7. 7. 7.5 9 9 5/6-8 80 0 56.5 304.8 76 63 94.5 390 90 47.6 44.5 78 7 8 /-3 00 30 353 304.8 0 80 0.5 390 90 47.6 44.5 78 7 8 /-3 50 457. 394 5 30 8 00 85.7 85.7 4 90 6 43.5 /-3 00 50.7 457 00 343 5 00 85.7 85.7 4 90 6 43.5 /-3 50 558.8 533 50 373 53 00 5 5 50 96 35 55 5/8-300 635 60 300 43 93 00 5 5 50 96 35 55 5/8- Note: Flanged 6" to " meet ASME B6.0 long pattern, 4" and smaller do not. Note: For flanged Face-Face dimension on sizes ½ through 4 are manufacturers standard; 6 through meet ASME B6.0 long pattern U (UNC) 6
SERIES 7000 & 8000 DIMENSIONS /4 VALVES (8mm - 300mm) G3 G N x øt G3 F F øeg øf øe øf3 øs øe3 N x øt F G F øe G øf øe G øf3 øs øe3 THREADED END 700/800 SOCKET WELD END 700/800 SCH 40 BUTT WELD END 7300/8300 FLANGED END 7400/8400 Flow-Tek s 3 piece Gvalve is offered with G5 a center Gbody and a large selection G of end connections. This versatile G6design offers easy customizing to meet most special G application requirements. øf5 øe G G5 øf øe G6 øf5 øe øf øe EXTENDED SOCKET WELD END 700/800 EXTENDED BUTT WELD END 7300/8300 Extended End connections may be fabricated from pipe and fittings. VALVE DIMENSIONS Models 7000 (36SS) / 8000 (WCB) Cv TORQUE WEIGHT SIZE E E E3 F F F3 F5 G G G3 G5 G6 N S T 8 LBS-IN 60 LBS.8 INCHES /4 0.55 0.36 0.98 0.54 0.90 0.500 8 60.8 3/8 0.69 0.49 0.98 0.68 0.90 0.500 3 60.8 / 0.85 0.6 0.57.0 0.84 3.50.4 0.90 0.500.67 4.50 4.00 4.38 0.6 54 95.3 3/4.07 0.8 0.79.39.05 3.88.46.0 0.560.4 4.56 4.00 4.75 0.6 05 40 3.4.33.05 0.98.65.3 4.5.77.07 0.63.4 4.6 4.00 4 3. 0.6 00 95 4.9 4.67.38.05.66.7.4 0.69 4.69 4.00 75 35 7.6.9.6.50.36.90 5.00.44.8 0.75.87 4.75 4.00 4 3.88 0.6 500 50.4.4.07.00.9.38 6.00.9.43 0.87 3.5 4.87 4.00 4 4.75 0.75 780 800.8.9.46 3.39.87.95 0.98,50,00 34.6 3 3.54.99.99 4.7 3.6 7.50.97 0.98 3.04 4 6.00 0.75,00 3,600 54.7 4 4.54 4.0 3.40 5.3 4.78 9.00.09.8 4.5 8 7.50 0.75 5,000 4,50 33.7 6 6.07 5.98 6.63.0 4.87 3.6 8 9.50 0.88 9,600 6,00 377 8 7.98 7.87 8.63 3.5 5.3 3.98 8.75 0.88 5,000 4,700 63.7 0 0.0 9.84 0.75 6.0 4.94 4.43 4.5.00,000,000 CF.94.8.75 9.0 5.4 4.65 7.00.00 8 KG-NM 6.8 KG 0.8 MILLIMETERS 8 4 9.5 5 3.7.8.7 8 6.8 0.8 0 7.5.5 5 7..8.7 3 6.8 0.8 5.7 5.8 4.4 8.3 88.9 9.8.7 4.5 4. 0.5 4 60.5 5.6 54 0.7. 0 7. 0.93 0 35 6.7 98.6 37 5.9 4.3 57 5.8 0.5 4 69.9 5.6 05 5.8.5 5 33. 8 6.6 5 4 33.4 07 45 7. 5.9 57 7. 0.5 4 79.3 5.6 00.0. 3 4.6 35. 5 4. 55 3.6 7.5 9 0.5 75 35.6 3.5 40 48.6 40.9 38 60 48.3 7 6 3.5 9. 73 0.6 0.5 4 98.6 5.6 500 57.6 5. 50 6. 5.5 50.8 74 60.3 5.4 74 36.. 80 3.7 0.5 4 0.7 9. 780 90.4 9.9 65 73.8 6.5 86 73 49.5 5,50 4.3 5.7 80 89.8 76 76 06 9 90.5 50 5 77.3 4 5.4 9.,00 406.7 4.8 00 5.4 0 0.5 35.5 8.6 53 30 4.5 8 90.5 9. 5,000 469 06 50 54. 5 68.3 79.4 3.6 9 8 4.3.4 9,600 700.5 7 00 0.7 00 9. 34.9 3.9 0 8 98.5.4 5,000,66 87 50 54.5 50 73. 406.4 5.4.5 36 5.4,000,486 CF 300 303. 300 33.6 48.6 30.5 8 43.8 5.4 Note: ¼"-4" weights are based on threaded end connection. 6"-" weights are based on Class 50 flanged ends. Torque values are at maximum rated pressures, clean water, RPTFE seats. Refer to Tech Bulletin 005 for complete torque information. For Cam Lock, Tube O.D. and Flush Bottom Tank connection dimensions and for other available End Connections, please consult the Flow-Tek factory. End connections are fully interchangeable and can be used in any combination. Note: Due to design constraints, ¼"- 4" flanged end connections do not meet ASME face-to-face dimensions. 7
FEATURES 3 PIECE VALVE BODY DESIGN The unique body design of the Series 7000/8000 offers many advantages, including installation flexibility, and ease of in line and out of line servicing. These time saving features are a big plus for process industries, automated valves and welded piping systems by reducing costly downtime. During maintenance, the actuator and mounting assemblies remain on the valve body. The entire valve and actuator assembly is easily reinstalled. No adjustment or reattachment is necessary. IN LINE SERVICING To perform in line maintenance, remove one of the body bolts through one of the two body hinges, loosen the remaining bolts and swing the body up. The valve can swing to the left or right depending on which bolt is removed. All body components can be serviced in this position without disturbing the pipe system. OUT OF LINE SERVICING For complete removal of valve from the line, remove the upper two bolts that go through the body hinges, loosen the lower two while keeping them in line, then lift the valve body out of the pipeline. The remaining two bolts keep the pipeline system in place and maintain alignment. The removed body can then be serviced and/or replaced. 3 PIECE WELD IN PLACE SERIES Socket-Weld and Butt-Weld Flow-Tek offers extended end connections for the Series 7000/8000 valves. These ends allow the customer to weld the valve in the piping system without damaging the seat or seals. Installation time and piping material is reduced. Additionally, the Weld In Place Series extended end connections limit potential installation errors. The valve is factory assembled and tested, then delivered to the customer for installation. No assembly of valve or actuation equipment is required valve and actuator integrity are maintained. The Weld In Place also eliminates the possibility of over-torquing the bolts or misplacing valve parts during installation. A Subsidiary of BRAY INTERNATIONAL, Inc. 833 N. Eldridge Pkwy #00 Houston, Texas 7704 83.9.300 Fax: 83.9.30 www.flow-tek.com All statements, technical information, and recommendations in this bulletin are for general use only. Consult Flow-Tek representatives or factory for the specific requirements and material selection for your intended application. The right to change or modify product design or product without prior notice is reserved. Flow-Tek is a registered trademark of Flow-Tek, Inc. 04 Flow-Tek, Inc. F-30_EN_S7K-8K_04-0