Aftermarket Tractor,Skidsteer & Wheel Loader Attachments

SEQ. #416-1217 MINNESOTA PRICING PAGES Titan Machinery M-B Companies December 2017 Price quote for: Aftermarket Tractor,Skidsteer & Wheel Loader Attachments Vendor Name: Titan Machinery Inc Contact Person: Brenden Honebrink Street Address: 644 East Beaton Drive P.O. Box: City, State, Zip West Fargo, ND Phone #: 952-445-5400 Toll Free #: 800-795-9274 Fax #: 952-445-0365 Email Address: govsales@titanmachinery.com 1.0 Manufacturer's Name Attachment Description Warranty Term (months, years) Percent Discount (%) to be applied to Price List Date & I.D. of Price List 2.0 Delivery Charges (See Special Terms and Conditions) DELIVERY STARTING POINT Price per loaded mile (City) (State, Zip Code) M-B Compaines Inc All Attachments 1 Year 8% 6/2016 - MB Pricing NO FLAT RATE ALLOWED New Holstein WI, 53061 $ 2.00 3.0 Price for additional Service Manual Price for additional Parts Manual Included Included 4.0 Installation Services: Per Hour (Shop Labor Rate) Installation services may be requested on an "as needed" basis. (See Special Terms and Conditions) $ 125.00

SWIFT EVENT TITLE & NUMBER: AFTERMARKET ATTACHMENTS FOR TRACTORS, SKIDSTEERS AND WHEEL LOADERS ** Following is a list of all distributors that are authorized to sell the contract equipment listed in the above solicitation. ** SWIFT Vendor Numbers: Provide the Swift Vendor Number (SWIFT ID) and Location Code (LOC CODE) for each Authorized Distributor. Each Authorized Distributor must have an accurate SWIFT ID. ** INSURANCE: All distributors MUST provide the required insurance certificates to the State as outline in the Swift Event Special Terms and Conditinos before any State Contract may be executed. COMPANY NAME SWIFT ID LOC CODE COMPANY ADDRESS ST /ZIP PHONE CONTACT NAME Titan Machinery Inc. 251892 18 6340 County Road 101 E, Shakopee MN, 55379 952-445-5400 Brenden Honebrink Titan Machinery Inc. 251892 6 4001 38th Street SW, Fargo ND, 54108 701-237-3333 Mary Aure Titan Machinery Inc. 251892 10 500 Ingersoll Ave, Crookston MN, 56716 218-281-4668 Kraig Rygg Titan Machinery Inc. 251892 19 4311 Haines Road, Hermantown MN, 55811 218-727-3038 John Kreklow Titan Machinery Inc. 251892 17 14375 James Road, Rogers MN, 55374 763-428-5099 Brenden Honebrink Titan Machinery Inc. 251892 2 1201 North Hwy 59, Marshall MN, 56258 507-532-5783 Lucas Hilgemann Titan Machinery Inc. 251892 5 4400W 62nd St N. Sioux Falls SD, 57104 605-336-3434 Matt Leighton Titan Machinery Inc. 251892 20 N 1626 Wuensch Road, La Crosse WI, 54601 608-788-1025 Jesse Schmidt

ARMT A 3-Point Mechanical Broom for Tractors Snow Dirt Debris Grass Specification General Mechanically driven rotary angle broom Available in 5 (60 ), 6 (72 ), 7 (84 ), 8 (96 ), and 9 (108 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 200 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting and storage Mounted to Category I or II 3 Point Hitch Brush 32 O.D x 10 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Frame 3½ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Heavy duty, self- aligning, pillow block bearings support the broom core Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength 12-Gauge steel end plates Hood covers 145 of brush Pre-drilled holes for easy installation of front deflecto Brush Lift Lift provided by means of prime mover Brush Drive Driveshaft from tractor s 540 RPM PTO is connected to broom gearbox Gearbox drives a cross shaft connected to a chain and sprocket system to drive the brush core Dirt Deflecto Sprinkler Systems Sight Indicators Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model ARMT Hydraulic Broom for Tractors 5-foot (60 ) Broom Poly/Wire Brush Hydraulic Swing M-B Yellow Category I or Category II Three Point Tractor Mount $6,880 * Prices starting at for standard model Broom Width 6-foot (72 ) Broom - add $130 7-foot (84 ) Broom - add $250 8-foot (96 ) Broom - add $380 9-foot (108 ) Broom - add $500 Brush Filament Poly (Polypropylene) - add $0 Rotation Direction Sweep away from tractor - add $0 Sweep towards tractor - add $0 Method of Swing Mechanical Swing - add $0 Optional Equipment Deflector (number of feet needed x $30/ft) - cost varies 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt Sight Indicators - add $80 www.m-bco.com 1.800.558.5800 ATTACHMENTS

FLB A Hydraulic Pick-Up Broom for Skid Steers and Loaders Dirt Debris Specification General Hydraulically driven rotary pick-up broom Available in 5 (60 ), 6 (72 ), and 7 (84 ) widths Broom speed up to 200 RPM, dependent on prime mover Hoses provided from hydraulic drive motor to a standard skid steer Brush 25 O.D x 6 3/8 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performance Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Lift Brush is lifted by means of the prime mover Brush Drive Brooms are standard with a single low-speed, high-torque, 18 c.i.d hydraulic motors Motors are coupled directly to the brush core by means of a 1 6 spline shaft Motors are mounted outside of brush frame and are protected by formed ¼ guards Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow Brush Hopper 12 Gauge hood with 10 gauge side panels ¼ steel plate hopper bottom Heavy duty, self- aligning, flange style bearings support the broom core Replaceable cutting edge Low Flow Drive Motor Sprinkler System Sight Indicators Gutter broom(s) Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow Hopper Dump Hopper is dumped by using the loader bucket dump function Hopper Capacity 5 (60 ) 13.2 cu. Ft. 6 (72 ) 15.8 cu. Ft. 7 (84 ) 18.2 cu. Ft. www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model FLB Hydraulic Pick Up Broom for Loaders 5-foot (60 ) Broom with 13.2 cu. ft. Hopper Poly/Wire Brush Standard Single Motor (12 to 20 GPM) M-B Yellow Standard Skid Steer Quick Coupler with hoses and couplers $4,180 * Prices starting at for standard model Broom Width 6-foot (72 ) Broom with 15.8 cu. ft. Hopper - add $200 7-foot (84 ) Broom with 18.2 cu. ft. Hopper - add $400 Brush Filament Poly (Polypropylene) - add $0 Dual Motor Size Low Flow (8-11 GPM) - add $100 Optional Equipment 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt Gutter broom, single - add $1,675 (Mounted on swing away bracket assembly. Brush driven by hydraulic motor with adjustable flow control for variable speed, independent of main brush. Flat wire bristles) Left Side Right Side Second Gutter Broom - add $1,285 (Right side and left side gutter brooms as described above in single gutter broom, plumbed in series with single flow control for variable speed, independent of main brush) Sight Indicators - add $80 www.m-bco.com 1.800.558.5800 ATTACHMENTS

HC-SNB A High Capacity Snow Blower for Skid Steers Snow Specification General 6 (72 ), 7 (84 ) & 8 (96 ) widths available 36 Cutting Height Dual Auger Motors 24 Serrated Auger Diameter 26 inch diameter impeller, with 4 blades and a 7 + depth 2,500-3,500 PSI Range 30-42 GPM Range Features Completely hydraulically driven auger and impeller Direct Sprocket driven Chute Rotation (no chain) with 270 deg rotation, with roller hold downs (not sliders) Hydraulically controlled deflecto 2 x 1/4 rolled flighting Auger with flat bar support Hardened Skid Shoes 1/2 x 6 Reversible cutting edge Steps on Skid Steer Quick Attach Complete wire harness for in-cab control Drift Cutters Loading Chute Hose Kit www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model HC-SNB Snowblower for Loaders 6-foot (72 ) Blower Control Box and Harness Standard skid steer quick coupler Hydraulic Deflector Black $12,250 Prices starting at for standard model * Blower Width 7-foot (84 ) Blower - add $250 8-foot (96 ) Blower - add $450 Hydraulic Hose Kit Hose Kit with Flat Face Coupler (customer must specify coupler size needed) - add $350 Mounting Kit Custom Mount Design Fee - add $2,500 Optional Equipment Truck loading chute - add $3,500 www.m-bco.com 1.800.558.5800 ATTACHMENTS

HD-SNB A Snow Blower for Loaders and Skid Steers Snow Specification General Available in 66, 72, 78 and 84 widths Hydraulically driven two-stage snow blower Up to 40 throw distance Sealed electrical connections with attachment control box Lift provided by means of the primes movers loader Housing 27 Intake height Fully welded 10 gauge housing with ¼ side plates Integrated lift points Replaceable side wear plates and adjustable rear cast iron skid-shoes support and level blower Replaceable bolt-on and adjustable, hardened cutting edge Auger 14 diameter with fully welded 5/16 flight thickness Directly driven by a hydraulic motor with pressure relief designed to accommodate spikes in hydraulic system due to blockage No gearbox or shear bolt service required Non-motor end supported by heavy-duty, self-aligning flange-type bearing Greaseable at each end for increased life Impeller Hydraulic motor driven, tapered hub mounting 20 diameter with 3/8 thick, reinforced 4-fin design Intake control plate to match snow type: Install plate to increase impeller suction for removal of lighter, more powdery snow Remove plate for greater snow volume during high moisture conditions Drift Cutters w/ Wing Extensions Truck Loading Chute Hydraulic Deflector Control Sight Indicators Independent Hydraulic System (Tractors with loaders) Discharge Chute 270 hydraulic rotation Rides in rollers to prevent freeze-up Chain-driven by separate hydraulic motor 45 sq. in. discharge volume area Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model HD-SNB Snowblower for Loaders 66 Blower Control Box and Harness Standard skid steer quick coupler Black $8,850 Prices starting at for standard model * Blower Width 72 Blower - add $100 78 Blower - add $150 84 Blower - add $200 Hydraulic Hose Kit Hose Kit with Flat Face Disconnects (skid steer application) - add $245 Mounting Kit Custom Mount Design Fee - add $2,500 Optional Equipment Hydraulic chute deflector - add $300 Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to blower) Required if tractor/loader auxiliary hydraulic system cannot supply 21 GPM @ 2,000 psi IHS Options: Tank Location Sight Indicators - add $80 Drift Cutters (with wing extensions) - add $360 www.m-bco.com 1.800.558.5800 ATTACHMENTS

HL A Hydraulic Broom for Skid Steers and Loaders Snow Dirt Debris Grass Specification General Hydraulically driven rotary angle broom Available in 5 (60 ), 6 (72 ), 7 (84 ), and 8 (96 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 200 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting, and storage Hoses provided from hydraulic drive motors to bulkhead or valve on broom Customer must supply hoses from bulkhead or valve to prime mover Spring system to damped transportation bounce Mounted with Skid Steer Quick Attach with easy entry steps Brush 32 O.D x 10 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Frame 3½ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Heavy duty, self- aligning, pillow block bearings support the broom core Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength 12-Gauge steel end plates Hood covers 140 of brush Pre-drilled holes for easy installation of front deflecto Brush Lift Lift provided by means of prime mover Brush pattern is adjustable by means of chain links Dirt Deflecto Low Flow Drive Motor Dual Standard Flow Drive Motors Dual Low Flow Drive Motors Sprinkler Systems Sight Indicators Oil Cooler Hose Kit Brush Drive Standard with a single low-speed, high-torque, 18 c.i.d hydraulic motor Motor is coupled directly to the brush core by means of a 1 ¼ 14 spline shaft Motor is mounted outside of brush frame and is protected by formed ¼ guards Motor mounts to brush frame with rubber bushings Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model HL Hydraulic Broom for Loaders 5-foot (60 ) Broom Poly/Wire Brush Standard Single Motor (12 to 20 GPM) Hydraulic Swing Cylinder ONLY M-B Yellow Standard Skid Steer Quick Coupler $5,450 Prices starting at for standard model * Broom Width 6-foot (72 ) Broom - add $100 7-foot (84 ) Broom - add $200 8-foot (96 dual motors, 25-45 GPM) Broom - add $825 Brush Filament Poly (Polypropylene) - add $0 Motor Size 5-7 foot HL Optional Dual Motor (25-45 GPM; 9000 in.lbs torque) - add $525 Low Flow (8-11 GPM) - add $100 Dual Low Flow (15-24 GPM; 6400 in.lbs torque) - add $675 8 foot HL Low Flow (15-24 GPM; 6400 in.lbs torque) - add $200 Method of Swing Electric/Hydraulic Swing (non-reversable) - add $1,225 (Valve, swing cylinder, control box with harness,and swing cylinder hoses, MAX 40GPM) Electric/Hydraulic Skid Steer Harness (customer to supply PIN OUT diagram) - add $1,300 (Valve, swing cylinder, custom wire harness and swing cylinder hoses, MAX 40GPM) Bobcat 7 Pin (non-reversable) - add $2,000 (Valve, swing cylinder, wire harness, and swing cylinder hoses, MAX 40 GPM) Loader Mounting Kit No Mounting (Mounting provided by customer) - subtract $100 Pin On Mount (Only applies if previously designed by MB) - add $1,000 Custom Mount Design Fee - add $2,500 Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Front (Tank mounts on broom mounting frame) - add $150 Optional Equipment 45 Gallon Sprinkler System (mounted on the brush hood) 12 Volt - add $1,290 150 Gallon Three-Point Mount Sprinkler System 12 Volt - add $2,180 Hose Kit (skid steer application) - add $235 Sight Indicators - add $80 Oil Cooler with Fan (available for dual motor brooms) - add $950 www.m-bco.com 1.800.558.5800 ATTACHMENTS

HLP A Hydraulic Broom for Loaders Snow Dirt Debris Grass Specification General Hydraulically driven rotary angle broom 32 diameter brush available in 6 (72 ), 7 (84 ) and 8 (96 ) broom widths Broom speed up to 200 rpm Standard with storage stands Frame Constructioned of 3-1/2 O.D. x.03 wall round tubular cross-member; 2 brush arms (formed from 1/4 plate) Self aligned bearings, with grease-able pillow block Brush Refillable core with flat wafers - po, wire, or combination (poly and wire combination on one wafer) Spacers and hubs manufactured from 20 gauge mild-steel strap 2 wide.broom removal without disconnecting hoses Allow for broom to follow surface contour Follow in swept path Swing Hydraulic angle change 30 left/right Parallel arms on top and bottom allow broom to float Brush Hood Coverage of 155 of broom Formed edge fold for strength Pre-drilled for installation of deflecto Ends covered by formed end plates Dirt Deflecto Electric/hydraulic swing and lift system Sight Indicators Sprinkler System Independent Hydraulic System Reserving Valve Casters Two 10 heavy duty casters with 360 swivel Brush Lift Provided by cylinder with 8 stroke and 2 bore Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model HLP Hydraulic Broom for Loaders 6-foot (72 ) Broom Poly/Wire Brush Standard Dual Motor (25 to 45 GPM) Hydraulic Swing - fourth function valve required M-B Yellow Standard Skid Steer Quick Coupler $7,040 Prices starting at for standard model * Broom Width 7-foot (84 ) Broom - subtract $370 8-foot (96 dual motors) Broom - add $1,305 Brush Filament Poly (Polypropylene) - add $0 Motor Size 6-7 foot Standard Single Motor (for prime mover with 12 to 20 GPM) - add $0 Optional Dual Motor (25-45 GPM) - add $525 Low Flow (8-11 GPM) - add $100 Dual Low Flow (15-24 GPM) - add $675 8 foot Standard Dual Motor (for prime mover with 25 to 45 GPM) - add $0 Low Flow (15-24 GPM) - add $200 Method of Swing Manual Swing - add $0 Electric/Hydraulic Swing (Valve and control box actuate the swing cylinder) - add $1,225 Loader Mounting Kit No Mounting (Mounting provided by customer) - subtract $100 Quick Coupler Mounting for loaders (Does not include cost of coupler) (Hook and Pin) - add $1,000 Mounting Frame with Pin-on ears (Customer may be required to provide dimensions) (Pin only) - add $1,000 Custom Mount Design Fee - add $2,500 Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Front (Tank mounts on broom mounting frame) - add $150 Optional Equipment 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt 150 Gallon Three-point Mount Sprinkler System - add $2,180 (cannot be used with three-point hydraulic tank) Sight Indicators - add $80 www.m-bco.com 1.800.558.5800 ATTACHMENTS

LB A Hydraulic Pick-Up Broom for Loaders Dirt Debris Dual Low or Standard Flow Drive Motors Single Low Flow Drive Motor Independent Hydraulic System (Tractors with loaders only) Sprinkler System(s) Hydraulic Dump Sight Indicators Gutter broom(s) Specification General Hydraulically driven rotary pick-up broom Available in 5 (60 ), 6 (72 ), 7 (84 ), and 8 (96 ) widths Broom speed up to 200 RPM, dependent on prime mover Hoses provided from hydraulic drive motor to a standard skid steer Heavy duty 10, 360 swivel casters Brush 25 O.D x 6 3/8 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Lift Brush is lifted by means of the prime mover Brush Drive 5, 6 and 7 brooms are standard with a single low-speed, high-torque, 18 c.i.d hydraulic motors 8 broom is standard with dual low-speed, high-torque, 18 c.i.d hydraulic motors Motors are coupled directly to the brush core by means of a 1 6 spline shaft Motors are mounted outside of brush frame and are protected by formed ¼ guards Brush Hopper 14 Gauge hood with ¼ side panels Heavy duty, self- aligning, flange style bearings support th broom core Adjustable baffle to fill bucket complet Rubber deflectors to help contain materia Hopper Bucket 10 Gauge bucket with 3/8 side plates ¼ wear bars welded to bottom of bucket to increase life Rubber deflectors to help contain materia Replaceable cutting edge Bucket Dump Hopper is dumped by using the loader bucket dump function Chains attached to loaders arm support the hopper which allows the bucket to dump Bucket Capacity 5 (60 ) 12.0 cu. Ft. 6 (72 ) 14.3 cu. Ft. 7 (84 ) 16.1 cu. Ft. 8 (96 ) 18.3 cu. Ft. Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model LB Hydraulic Pick Up Broom for Loaders 5-foot (60 ) Broom with 12 cu. ft. Hopper Poly/Wire Brush Standard Single Motor (12 to 20 GPM) M-B Yellow Standard Skid Steer Quick Coupler $5,600 Prices starting at for standard model Broom Width 6-foot (72 ) Broom with 14.3 cu. ft. Hopperr - add $190 7-foot (84 ) Broom with 16.1 cu. ft. Hopper - add $380 8-foot (96 dual motor) Broom with 18.3 cu. ft. Hopper - add $855 Brush Filament Poly (Polypropylene) - add $0 Motor Size Low Flow (8-11 GPM) - add $100 Optional Dual Motor Size Standard (for prime mover with 25 to 45 GPM) - add $500 Low Flow (for prime mover with 15 to 24 GPM) - add $650 Mounting Frame with Pin-on Ears - add $2,700 Euro Coupler - add $0 Quick Attach Frame with ACS Pro or Caterpillar Coupler - add $2,200 Quick Attach Frame with JRB Coupler - add $1,500 Quick Attach Frame with FFC Coupler (Customer may be required to provide dimensions) - add $1,500 Quick Attach Frame with Volvo Coupler None (blank bucket) Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Front Tank (mounts on broom mounting frame) - add $150 Optional Equipment 45 Gallon Sprinkler System (mounted on the brush hood) - add $1,290 12 Volt 24 Volt 150 Gallon Sprinkler System (Customer provides tank mounting location) - add $2,180 12 Volt 24 Volt Cannot be mounted on hood Gutter broom, single - add $1,675 (Mounted on swing away bracket assembly. Brush driven by hydraulic motor with adjustable flow control for variable speed, independent of main brush. Flat wire bristles.) Left Side Right Side Second Gutter Broom - add $1,285 (Right side and left side gutter brooms as described above in single gutter broom, plumbed in series with single flow control for variable speed, independent of main brush) Hydraulic Dump (Dumps by reversing hydraulic flow) - add $350 Sight Indicators - add $80 www.m-bco.com 1.800.558.5800 ATTACHMENTS

*Standard model LLB Hydraulic Pick Up Broom for Loaders 7-foot (84 ) Broom with 33 cu. ft. Hopper Poly/Wire Brush Standard Dual Motor (25 to 45 GPM) M-B Yellow Blank Bucket $19,308 * Prices starting at for standard model Broom Width 8-foot (96 ) Broom with 37.5 cu. ft. Hopper - add $1,355 9-foot (108 ) Broom with 42 cu. ft. Hopper - add $2,445 Note: Pin and/or quick-attach mountings for most popular applications. Some loaders with quick-attach buckets will require customer to provide female quick-attach. Consult factory. Note: Prices do not include hydraulic valve(s) on prime mover. Brush on/off with tractor/loader valve. Brush Filament Poly (Polypropylene) - add $0 Dual Motor Size Low Flow (15-24 GPM) - add $200 Loader Mounting Kit (please inquire if your coupler style is not shown) Quick Attach From with ACS Pro 2000 or CAT Fusion - add $3,400 Quick Attach Frame with JRB Coupler - add $2,900 Quick Attach Frame with Volvo Coupler or Cat IT - add $2,200 Mounting Frame with Pin-on Ears (Customer may be required to provide dimensions) - add $1,500 Custom Mount Design Fee (Actual cost of coupler will be based after design) - add $2,500 Optional Equipment 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt 150 Gallon Sprinkler System (Customer provides tank mounting location) - add $2,180 12 Volt 24 Volt Cannot be mounted on hood Gutter broom, single - add $2,390 (Mounted on swing away bracket assembly. Brush driven by hydraulic motor with adjustable flow control for variable speed, independent of main brush. Flat wire bristles.) Second Gutter Broom - add $2,190 (Right side and left side gutter brooms as described above in single gutter broom, plumbed in series with single flow www.m-bco.com 1.800.558.5800 M-B Companies, Inc. M-B is a registered trademark of M-B Companies, Inc. 2015 M-B Companies, Incorporated. All Rights Reserved. 2015 M-B Attachments Product Guide 0615A Effective 06/2015-05/2016

RHT 3 Point Mounted Hydraulic Broom for Tractors Snow Dirt Debris Grass Dirt Deflecto Low Flow Drive Motor Dual Standard Flow Drive Motors Dual Low Flow Drive Motors Sprinkler Systems Sight Indicators Specification General Hydraulically driven rotary angle broom Available in 6 (72 ), 7 (84 ), and 8 (96 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 200 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting, and storage Hoses provided from hydraulic drive motors to bulkhead or valve on broom Customer must supply hoses from bulkhead or valve to prime mover Mounted to Category I or II 3 Point Hitch Brush 32 O.D x 10 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Frame 3½ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Heavy duty, self- aligning, pillow block bearings support the broom core Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength 12-Gauge steel end plates Hood covers 145 of brush Pre-drilled holes for easy installation of front deflecto Brush Lift Lift provided by means of prime mover Brush pattern is adjustable by means of a threaded shaft on the lift cylinder Brush Drive Standard with a single low-speed, high-torque, 18 c.i.d hydraulic motor Motor is coupled directly to the brush core by means of a 1 6 spline shaft Motor is mounted outside of brush frame and is protected by formed ¼ guards Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model RHT Hydraulic Rear Broom for Tractors 6-foot (72 ) Broom Poly/Wire Brush Single Single Motor (12 to 20 GPM) Hydraulic Swing M-B Yellow Category I or II Three Point Tractor Mount $5,738 * Prices starting at for standard model Broom Width 7-foot (84 ) Broom - add $162 8-foot (96 dual motors; 25-40 GPM) Broom - add $862 Brush Filament Poly (Polypropylene) - add $0 Motor Size 6-7 Foot Optional Dual Motor (for prime mover with 25 to 40 GPM) - add $525 Low Flow (for prime mover with 8 to 11 GPM) - add $100 Dual Low Flow (for prime mover with 15 to 24 GPM) - add $725 8 Foot Low Flow (for prime mover with 15 to 24 GPM) - add $200 Method of Swing Manual Swing - add $0 Electric/Hydraulic Swing (Valve and control box actuate the swing cylinder) Max 30 GPM - add $1,025 Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Rear Tank (mounts on broom mounting frame) - base IHS price Optional Equipment 45 Gallon Sprinkler System (Customer provides tank mounting location) - add $1,290 12 Volt 24 Volt www.m-bco.com 1.800.558.5800 ATTACHMENTS

SHL A Hydraulic Broom for Small Loaders Snow Dirt Debris Grass Dirt Deflecto Independent Hydraulic System (Turf and tractors only) Low Flow Drive Motor Dual Low or Standard Flow Drive Motors Hydraulic Engine Pallets (Trucks only) Sprinkler System Sight Indicators Specification General Hydraulically driven rotary angle broom Available in 4 (48 ), 5 (60 ), 6 (72 ) and 7 (84 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 200 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting, and storage Hoses provided from hydraulic drive motor(s) to bulkhead or valve on broom Customer must supply hoses from bulkhead or valve to prime mover Brush 25 O.D x 6 3/8 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Brush Frame 2⅞ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Heavy duty, self- aligning, pillow block bearings support the broom core Threaded adjustable link to compensate brush pattern from wear Caster wheels **Truck and commercial turf only** Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength Hood covers 130 of brush Pre-drilled holes for easy installation of front deflecto Brush Lift SHL Brush head is lifted by means of the prime mover SHT Brush head is lifted by a hydraulic cylinder Brush Drive 5, 6, 7 brooms are standard with a single low-speed, high-torque, 18 c.i.d hydraulic motors Motors are coupled directly to the brush core by means of a 1 6 spline shaft Motors are mounted outside of brush frame and are protected by formed ¼ guards Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model SHL Hydraulic Broom for Loaders 4-foot (48 ) Broom Poly/Wire Brush Standard Single Motor (12 to 20 GPM) Hydraulic Swing M-B Yellow Standard Skid Steer Quick Coupler $4,375 Prices starting at for standard model * Broom Width 5-foot (60 ) Broom - add $150 6-foot (72 ) Broom - add $250 7-foot (84 ) Broom - add $450 Brush Filament Poly (Polypropylene) - add $0 Motor Size Low Flow (8-11 GPM) - add $100 Method of Swing Electric/Hydraulic Swing (non-reversable) - add $1,225 (Valve, swing cylinder, control box with harness,and swing cylinder hoses, MAX 40GPM) Electric/Hydraulic Skid Steer Harness (customer to supply PIN OUT diagram) - add $1,300 (Valve, swing cylinder, custom wire harness and swing cylinder hoses, MAX 40GPM) Bobcat 7 Pin (non-reversable) - add $1,600 (Valve, swing cylinder, wire harness, and swing cylinder hoses, MAX 40 GPM) Loader Mounting Kit No Mounting (Mounting provided by customer) - subtract $100 Pin On Mount (Only applies if previously designed by M-B) - add $1,000 Mini Skid Steer (Toro Dingo) - add $0 Custom Mount Design Fee - add $2,500 Independent Hydraulic system (IHS) Independent Hydraulic system (IHS) - add $2,400 (Includes Rear 540 PTO hydraulic pump, relief valve,oil cooler 3-point hydraulic reservoir and hoses to broom) Required if tractor/loader auxiliary hydraulic system cannot supply 8 GPM @ 2,000 psi IHS Options: Tank Location Front (Tank mounts on broom mounting frame) - add $150 Optional Equipment 45 Gallon Sprinkler System (mounted on the brush hood) 12 Volt 24 Volt - add $1,290 Hose Kit (skid steer application) - add $235 Sight Indicators - add $80 www.m-bco.com 1.800.558.5800 ATTACHMENTS

TKH-L A Hydraulic Broom for Loaders Snow Dirt Debris Dirt Deflecto Electric/Hydraulic Swing Independent Hydraulic System (Tractors only) Dual Low Flow Drive Motors Sprinkler Systems Front Spray Bar Only Oil Cooler Specification General Hydraulically driven rotary angle broom Available in 7 (84 ), 8 (96 ), 9 (108 ), 10 (120 ), 11 (132 ) and 12 (144 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 250 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting, and storage Brush head is lifted by means of the prime mover Hoses provided from hydraulic drive motors to bulkhead or valve on broom Customer must supply hoses from bulkhead or valve to prime mover Sight Indicators Brush 32 O.D x 10 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Quick change brush core Brush Frame 3½ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Rectangular front support bar for additional frame strength Adjustable link to compensate brush pattern from wear Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength 12-Gauge steel end plates Hood covers 145 of brush Pre-drilled holes for easy installation of front deflector Brush Drive Standard with dual low-speed, high-torque, 18 c.i.d hydraulic motors Motors are coupled directly to the brush core by means of a 5-5/16 poly hexagonal hub Motors are recessed into brush frame to protect from collision Casters Two 16 ½ x 8, 8 Ply LR-D casters mounted behind the brush frame 360 of maneuverability Sealed and greaseable 2 OD caster stem Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model TKH-L Hydraulic Broom for Loaders 7-foot (84 ) Broom Poly/Wire Brush Standard Dual Motor (28 to 40 GPM) Hydraulic Swing Cylinder ONLY (4th function valve required) M-B Yellow Mounting Frame with No Quick Coupler $10,884 Prices starting at for standard model * Broom Width 8-foot (96 ) Broom - add $124 9-foot (108 ) Broom - add $248 10-foot (120 ) Broom - add $372 11-foot (132 ) Broom - add $838 12-foot (144 ) Broom - add $962 Brush Filament Poly (Polypropylene) - add $0 Dual Motor Size Low Flow (16-24 GPM) - add $200 Method of Swing Electric/Hydraulic Swing with reverse rotation capabilities from loader - add $1,225 (Valve, swing cylinder, control box with harness,and swing cylinder hoses, MAX 40GPM) Loader Mounting Kit Quick Attach From with ACS Pro 2000 or CAT Fusion - add $3,550 Quick Attach Frame with JRB Coupler - add $3,000 Quick Attach Frame with Volvo Coupler - add $2,000 Quick Attach Frame with CAT IT - add $2,450 Quick Attach Frame with Euro Style Coupler - add $1,500 Mounting Frame with Pin-on Ears - add $1,500 Optional Equipment 150 Gallon Three-Point Mount Sprinkler System (12 or 24 Volt) - add$2,180 45 Gallon Sprinkler System (mounted on the brush hood) - add $1,290 Parallel Arm Flotation System - add $2,000 Oil Cooler with Fan - add $2000 www.m-bco.com 1.800.558.5800 ATTACHMENTS

TKH-T A Hydraulic Broom for Tractors Snow Dirt Debris Dirt Deflecto Electric/Hydraulic Swing Independent Hydraulic System (Tractors only) Dual Low Flow Drive Motors Sprinkler Systems Front Spray Bar Only Oil Cooler Specification General Hydraulically driven rotary angle broom Available in 7 (84 ), 8 (96 ), 9 (108 ), 10 (120 ), 11 (132 ) and 12 (144 ) widths Hydraulic swing capable of 30 left or right of center Broom speed up to 250 RPM, dependent on prime mover Storage stands for simple mounting, dis-mounting, and storage Brush head is lifted by means of the prime mover Hoses provided from hydraulic drive motors to bulkhead or valve on broom Customer must supply hoses from bulkhead or valve to prime mover Sight Indicators Brush 32 O.D x 10 I.D wafer style brush 2 spacers manufactured from 20-gauge mild steel strap Brush core can be installed with either end to the left or right with no effect on sweeping performanc Brush and core assembly can be removed from frame without disconnecting hoses from drive motor(s) Quick change brush core Brush Frame 3½ O.D. round tubular cross member Two brush arms formed from ¼ steel plate Rectangular front support bar for additional frame strength Adjustable link to compensate brush pattern from wear Brush Hood Manufactured from 16- Gauge steel with formed edge fold for additional strength 12-Gauge steel end plates Hood covers 145 of brush Pre-drilled holes for easy installation of front deflector Brush Drive Standard with dual low-speed, high-torque, 18 c.i.d hydraulic motors Motors are coupled directly to the brush core by means of a 5-5/16 poly hexagonal hub Motors are recessed into brush frame to protect from collision Casters Two 16 ½ x 8, 8 Ply LR-D casters mounted behind the brush frame 360 of maneuverability Sealed and greaseable 2 OD caster stem Finish Steel surfaces undergo a phosphatizing acid bath to clean and etch the surfaces to provide superior adhesion Epoxy primer and polyurethane topcoat Painted M-B yellow www.m-bco.com M-B Attachments 1.800.558.5800

*Standard model TKH-T Hydraulic Broom for Tractors 7-foot (84 ) Broom Poly/Wire Brush Standard Dual Motor (28 to 40 GPM) Hydraulic Swing Cylinder ONLY Category I or II Three Point Hitch $10,884 * Prices starting at for standard model Broom Width 8-foot (96 ) Broom - add $124 9-foot (108 ) Broom - add $248 10-foot (120 ) Broom - add $372 11-foot (132 ) Broom - add $838 12-foot (144 ) Broom - add $962 Brush Filament Poly (Polypropylene) - add $0 Dual Motor Size Low Flow (16-24 GPM) - add $200 Method of Swing (Typically operated by tractor controls) Electric/Hydraulic Swing- add $1,225 (Valve and control box with harness; MAX 40GPM) Optional Equipment 150 Gallon Three-Point Mount Sprinkler System - add $2,180 (Cannot be mounted to brush hood or used with rear 3 Point mounted TKH) 45 Gallon Sprinkler System (mounted on the brush hood) - add $1,290 Parallel Arm Floatation System - add $2,000 Oil Cooler with Fan - add $950 www.m-bco.com 1.800.558.5800 ATTACHMENTS