Directionl spool vlves, pilot-operted, with electro-hydrulic ctution ype WEH =UR RE 24802 Edition: 2016-12 Solenoid coil is n pproved component with UR-mrking ccording to UL 906 Size 10 32 Component series 4; 6; 7 Mximum operting pressure 350 r [5076 psi] Mximum flow 1100 l/min [290 US gpm] H8051 Fetures 4/3-, 4/2- or 3/2-wy version For suplte mounting orting pttern ccording to ISO 4401 Spring or pressure centering, spring end position or hydrulic end position Wet-pin DC or C solenoids, optionl Electricl connection s individul connection Conceled mnul override Optionl versions: Switching time djustment relod vlve in chnnel of the min vlve Stroke setting nd/or spool position monitoring Contents Fetures 1 Ordering code 2 4 Symols 5 9 Function, section 10, 11 ilot oil supply 12, 13 echnicl dt 14 16 Switching times 17 Chrcteristic curves, performnce limits 18 28 Dimensions 29 34 Stroke setting, mounting options 35, 36 Switching time djustment 37 ressure reducing vlve "D3" 37 relod vlve (not for NG10) 38 roject plnning informtion 39 Further informtion 39 RE 24802, edition: 2016-12, osch Rexroth G
2/40 WEH Directionl spool vlve Ordering code 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 WEH / N9 K4 / = UR * 01 Up to 280 r no code Up to 350 r H 02 3-wy version 3 4-wy version 4 ypes of ctution 03 Electro-hydrulic WEH Size 04 NG10 10 NG16 16 NG25 (version "WEH 22") 22 NG25 (version "WEH 25") 25 NG32 32 Control spool return in the min vlve 05 y mens of springs no code Hydrulic 1) 06 For symols, see pge 5 nd 6 07 Component series 40 49 (40 49: unchnged instlltion nd connection dimension) NG10 4 Component series 60 69 (60 69: unchnged instlltion nd connection dimensions) NG25 ("WEH 25") 6 nd NG32 Component series 70 79 (70 79: unchnged instlltion nd connection dimensions) NG16 (from series 72) nd NG25 ("WEH 22") 7 Control spool return in the pilot control vlve with 2 switching positions nd 2 solenoids (Only possile with symols,, C, D, K, Z nd hydrulic control spool return in the min vlve) 08 With spring return no code Without spring return O Without spring return with detent OF ilot control vlve 09 High-power vlve (dt sheet 23208) 6E 10 Direct voltge 12 V G12 Direct voltge 24 V G24 C voltge 110 V or 120 V, 50/60 Hz W110 11 With conceled mnul override N9 2) ilot oil flow 12 Externl pilot oil supply, externl pilot oil return 3) no code Internl pilot oil supply, externl pilot oil return 3; 4) E Internl pilot oil supply, internl pilot oil return 4) E Externl pilot oil supply, internl pilot oil return 3) (Version "E" nd "" with 3-spool position vlve, pressure-centered only possile if p St 2 x p tnk + p St min!) Switching time djustment 13 Without switching time djustment no code Switching time djustment s supply control S Switching time djustment s dischrge control S2 H osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 3/40 Ordering code 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 WEH / N9 K4 / = UR * Electricl connection 14 Individul connection Without mting connector; connector DIN EN 175301-803 K4 5) Spool position monitoring 15 Without position switch no code Inductive position switch type QM Monitored spool position "" Monitored spool position "" Monitored rest position QMG24 QMG24 QM0G24 Inductive proximity sensor type QS Monitored spool position "" Monitored spool position "" Monitored spool position "0" Monitored spool position "0" nd "" Monitored spool position "0" nd "" Monitored spool position "" nd "" QSG24W QSG24W QS0G24W QS0G24W QS0G24W QSG24W For more informtion, see dt sheet 24830 Stroke setting 16 For ordering code, see pge 35 nd 36 hrottle insert 17 Without throttle insert no code With throttle insert 6) : hrottle Ø 0.8 mm [0.0315 inch] hrottle Ø 1.0 mm [0.0394 inch] hrottle Ø 1.2 mm [0.0472 inch] hrottle Ø 1.5 mm [0.0591 inch] hrottle Ø 2.0 mm [0.0787 inch] hrottle Ø 2.5 mm [0.0984 inch] 08 10 12 15 20 25 relod vlve (not for NG10) 18 Without prelod vlve no code With prelod vlve (p c = 4.5 r [65 psi]) 4,5 19 Without pressure reducing vlve no code With pressure reducing vlve D3 7) Sel mteril 20 NR sels no code FKM sels V Oserve comptiility of sels with hydrulic fluid used. (Other sels upon request) 21 Solenoid coil is n pproved component with UR-mrking ccording to UL 906 = UR 22 For further informtion, see the plin text * p pilot p pilot min p tnk p c = pilot pressure = minimum pilot pressure = tnk pressure = crcking pressure Explntion of the footnotes, see pge 4. RE 24802, edition: 2016-12, osch Rexroth G
4/40 WEH Directionl spool vlve Ordering code 1) 2 spool positions (hydrulic end position): only symols C, D, K, Z, 3 switching positions (hydruliclly centered): only NG16, NG25 ("4W.H 25") nd NG32 2) he mnul override cnnot e llocted sfety function. he mnul override units my only e used up to tnk pressure of 50 r. 3) ilot oil supply or return externl: he mximum dmissile operting prmeters of the pilot control vlve must e oserved (see dt sheet 23208)! Minimum pilot pressure: plese oserve pge 15! Mximum pilot pressure: plese oserve pge 15! 4) ilot oil supply internl (version "E" nd "E"): Minimum pilot pressure: plese oserve pge 15! Mximum pilot pressure: plese oserve pge 15! With higher pilot pressure, use of pressure reducing vlve "D3" is required (if it is not used pilot pressure = operting pressure t the port!). In order to prevent indmissily high pressure peks, "10" throttle insert hs to e provided in port of the pilot control vlve (see pge 13). In connection with version "H", the pressure reducing vlve "D3" is lso required. 5) Mting connectors, seprte order, see dt sheet 23208 nd 08006 6) When the dmissile vlve performnce limits re exceeded, instlltion of throttle inserts is to e intended (performnce limits see pge 21 to 28). 7) Only in connection with the "10" throttle insert osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 5/40 Symols: 2 spool positions = 1) = 1) = C = = D = K = Z 1) Only for NG10 nd 25 ("4WEH 22") with 3/2-wy version; if operting pressure > tnk pressure, port is to e used s lekge port! 2) Exmple: Symol E with ctuting side "" ordering code..e.. 3) Symol S only for NG16 Ordering code Symol Control spool return ype of ctution 1), C, D, K, Z 1),../....H../....H../O..H../OF../....H../.. RE 24802, edition: 2016-12, osch Rexroth G
6/40 WEH Directionl spool vlve Symols: 3 spool positions = E 2) = Q = F = R = G = S 3) = H = = J = L = M = U = V = W = Explntion of the footnotes, see pge 5. Ordering code Symol ctuting side Control spool return ype of ctution../.. 0. 0 E, F, G, H, J, L, M,, Q, R, S,, U, V, W. 0..H../.. 0 H. 0 H. 0 osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 7/40 RE 24802, edition: 2016-12, osch Rexroth G Vlve with spring end position Vlve with hydrulic end position = externl; = externl ype WEH /.. ype WEH. H../... ype WEH. H../O... ype WEH. H../OF...,,,,,,,, = internl; = externl ype WEH / E ype WEH. H../ E ype WEH. H../O E ype WEH. H../OF E,,,,,,,, = internl; = internl ype WEH / E ype WEH. H../ E ype WEH. H../O E ype WEH. H../OF E,,,,,,,, Symols for vlves with 2 spool positions
8/40 WEH Directionl spool vlve Symols for vlves with 2 spool positions Vlve with spring end position Vlve with hydrulic end position ype WEH / ype WEH. H../ ype WEH. H../O ype WEH. H../OF = externl; = internl,,,,,,,, Symols for vlves with 3 spool positions Vlve with spring-centered zero position ype WEH / Vlve with pressure-centered zero position only NG16, 25 ("W.H 25") nd 32 ype WEH. H../, 0, 0,, = externl; = externl L 0 0 L ype WEH / E ype WEH. H../ E = internl; = externl 0,, 0 0,, L 0 L osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 9/40 Symols for vlves with 3 spool positions Vlve with spring-centered zero position ype WEH / E 0,, Vlve with pressure-centered zero position only NG16, 25 ("W.H 25") nd 32 ype WEH. H../ E 0,, = internl; = internl L 0 0 L ype WEH / 0,, ype WEH. H../ 0,, = externl; = internl L 0 0 L Notice: 3-spool position vlves, pressure-centered, preferly with externl pilot oil supply nd/or return ("no code", "E") For preconditions for internl pilot oil supply nd/or return ("E", ""), see pge 4 nd 14. RE 24802, edition: 2016-12, osch Rexroth G
10/40 WEH Directionl spool vlve Function, section: ype WEH 5.2 4 10 5.1 9 9 1 2 3.2 7 3.1 8 6 Directionl vlves type WEH he vlve type WEH is directionl spool vlve with electro-hydrulic ctution. It controls the strt, stop nd direction of flow. he directionl vlves siclly consist of the min vlve with housing (1), the min control spool (2), one or two return springs (3.1) nd (3.2), s well s the pilot control vlve (4) with one or two solenoids "" (5.1) nd/or "" (5.2). he min control spool (2) in the min vlve is held in the zero or initil position y the springs or y mens of pressuriztion. In the initil position, the two spring chmers (6) nd (8) re connected with the tnk in depressurized form vi the pilot control vlve (4). Vi the control line (7), the pilot control vlve is supplied with pilot oil. Supply cn e implemented internlly or externlly (externlly vi port ). Upon ctution of the pilot control vlve, e.g. solenoid "", the pilot control spool (10) is moved to the left nd thus, the spring chmer (8) is pressurized with pilot pressure. he spring chmer (6) remins depressurized. he pilot pressure cts on the left side of the min control spool (2) nd moves it ginst the spring (3.1). his connects port with nd with in the min vlve. On switching off of solenoid, the pilot control spool (10) returns to its initil position (except impulse spool). he spring chmer (8) is unloded to the tnk. he pilot oil return is implemented internlly (vi chnnel ) or externlly (vi chnnel ). n optionl mnul override (9) llows for moving of the pilot control spool (10) without solenoid energiztion. Notes: he return springs (3.1) nd (3.2) in the spring chmers (6) nd (8) hold the min control spool (2) in centrl position without pilot pressure even with, for exmple, verticl vlve positioning. Due to the design principle, internl lekge is inherent to the vlves, which my increse over the life cycle. For pilot oil supply, see pge 12 nd 13. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 11/40 Function, section: ype WEH H 5.2 4 10 5.1 9 9 1 2 3.2 7 3.1 8 6 12 L 4/3 directionl vlve with pressure centering of the min control spool, type WEH H he min control spool (2) in the min vlve is kept in the zero position y pressuriztion of the two front fces. One centering ush (12) rests on the housing nd fixes the control spool position. y pressure relief of one front fce, the min control spool (2) is moved to the switching position. he unloded control spool fce displces the returning pilot oil into chnnel (externl) vi the pilot control vlve. Notes: he springs (3.1) nd (3.2) do not hve return function in this version. hey hold the min control spool (2) in centrl position in the depressurized condition nd with horizontl instlltion. RE 24802, edition: 2016-12, osch Rexroth G
12/40 WEH Directionl spool vlve ilot oil supply (schemtic illustrtion) NG10 NG16 2 1 2 1 NG25 ("W.H 22") NG25 ("W.H 25") 2 1 3 1 NG32 1 2 1 lug screw M6 ccording to DIN 906, wrench size 3 pilot oil return 2 lug screw M6 ccording to DIN 906, wrench size 3 pilot oil supply 3 lug screw M12 x 1.5 ccording DIN 906, wrench size 6 pilot oil supply ilot oil supply externl: 2, 3 closed internl: 2, 3 open ilot oil return externl: 1 closed internl: 1 open Further explntions on pge 13. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 13/40 ilot oil supply ype WEH... he pilot oil supply is implemented externlly - vi chnnel - from seprte pressure supply. he pilot oil return is implemented externlly - vi chnnel - into the tnk. ype WEH E he pilot oil supply is implemented internlly from chnnel of the min vlve. (see pge 14, footnotes 5) nd 6) ) he pilot oil return is implemented externlly - vi chnnel - into the tnk. In the suplte, port is closed. ype WEH E he pilot oil supply is implemented internlly from chnnel of the min vlve. he pilot oil return is implemented internlly - vi chnnel - into the tnk. In the suplte, ports nd re closed. ype WEH he pilot oil supply is implemented externlly - vi chnnel - from seprte pressure supply. he pilot oil return is implemented internlly - vi chnnel - into the tnk. In the suplte, port is closed. hrottle insert Use of the throttle insert (5) is necessry if the pilot oil supply in chnnel of the pilot control vlve is to e limited (see elow). he throttle insert (5) is inserted in chnnel of the pilot control vlve. Notes: he modifiction of the pilot oil supply my only e performed y uthorized specilists or t the fctory! ilot oil supply or return externl: he mximum dmissile operting prmeters of the pilot control vlve must e oserved (see dt sheet 23208)! Mximum pilot pressure: plese oserve pge 15! ilot oil supply internl (version "E" nd "E"): Minimum pilot pressure: plese oserve pge 14! In order to prevent indmissily high pressure peks, "10" throttle insert hs to e provided in port of the pilot control vlve (see ove). In connection with version "H", the pressure reducing vlve "D3" (see pge 37) is lso required. 3 5 4 3 ilot control vlve 4 Min vlve 5 hrottle insert RE 24802, edition: 2016-12, osch Rexroth G
14/40 WEH Directionl spool vlve echnicl dt (For pplictions outside these prmeters, plese consult us!) generl Sizes NG 10 16 25 "W.H 22" Weight, pprox. Instlltion position 25 "W.H 25" Vlve with one solenoid kg [ls] 6.4 [14.1] 8.5 [18.7] 11.5 [25.3] 17.6 [38.8] 17.6 [38.8] Vlve with two solenoids, spring-centered kg [ls] 6.8 [15.0] 8.9 [19.6] 11.9 [26.2] 19.0 [41.9] 41.0 [90.4] Vlve with two solenoids, pressure-centered kg [ls] 6.8 [15.0] 8.9 [19.6] 11.9 [26.2] 19.0 [41.9] 41.0 [90.4] Vlve witch hydrulic ctution (type WH...) kg [ls] 5.5 [12.1] 7.3 [16.1] 10.5 [23.1] 16.5 [36.4] 39.5 [87.1] Switching time djustment "S" nd "S2" kg [ls] 0.8 [1.8] 0.8 [1.8] 0.8 [1.8] 0.8 [1.8] 0.8 [1.8] ressure reducing vlve "D3" kg [ls] 0.4 [0.9] 0.4 [0.9] 0.4 [0.9] 0.4 [0.9] 0.4 [0.9] ny; horizontl with vlves with hydrulic control spool return "H" nd symol,, C, D, K, Z,. With suspended instlltion, higher sensitivity to contmintion horizontl is recommended. mient temperture rnge C [ F] 20 +70 [ 4 +158] (NR sels) 15 +70 [+5 +158] (FKM sels) Storge temperture rnge C [ F] +5 +40 [+41 +104] Surfce protection (vlve ody) Coting, lyer thickness mx. 100 µm Mximum storge time ers 1 32 hydrulic Mximum operting pressure ort,, ype WEH r [psi] 280 [4061] 280 [4061] 280 [4061] 280 [4061] 280 [4061] ort Externl pilot oil return Internl pilot oil return 1) ort Externl pilot oil return ype H-WEH, WEH ype H-WEH r [psi] 350 [5076] ype WEH r [psi] 280 [4061] 350 [5076] 350 [5076] 350 [5076] 350 [5076] 250 [3626] 250 [3626] 250 [3626] 250 [3626] ype H-WEH 315 [4568] 250 [3626] 250 [3626] 250 [3626] 250 [3626] ype H-WEH, r [psi] 180 [2610] with direct voltge WEH 160 [2320] with lternting voltge r [psi] 180 [2610] with direct voltge 160 [2320] with lternting voltge Hydrulic fluid see tle on pge 16 Hydrulic fluid temperture rnge (t the vlve working ports) C [ F] 20 +80 [ 4 +176] (NR sels) 15 +80 [+5 +176] (FKM sels) Viscosity rnge mm 2 /s [SUS] 2.8 500 [35 2320] Mximum dmissile degree of contmintion of the hydrulic fluid Clss 20/18/15 2) clenliness clss ccording to ISO 4406 (c) 1) s 3-spool position vlve, pressure-centered only possile if p St 2 x p tnk + p St min. 2) he clenliness clsses specified for the components must e dhered to in hydrulic systems. Effective filtrtion prevents fults nd simultneously increses the life cycle of the components. For selecting the filters, see www.oschrexroth.com/filter. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 15/40 echnicl dt (For pplictions outside these prmeters, plese consult us!) hydrulic Size NG 10 16 25 "W.H 22" Mximum pilot pressure 3) r [psi] 250 [3626] Minimum pilot pressure ilot oil supply externl (ll symols), pilot oil supply internl (only symols D, K, E, J, L, M, Q, R, U, W) 3-spool position vlve, spring-centered 250 [3626] 210 [3046] 25 "W.H 25" 250 [3626] 32 250 [3626] ype H-WEH r [psi] 12 [174] 14 [203] 12.5 [181] 13 [188] 8.5 [123] ype WEH... r [psi] 12 [174] 14 [203] 10.5 [152] 13 [188] 8.5 [123] 3-spool position vlve, pressure-centered r [psi] 14 [203] 18 [261] 8.5 [123] 2-spool position vlve with spring ype H-WEH r [psi] 10 [145] 14 [203] 14 [203] 13 [188] 10 [145] end position ype WEH... r [psi] 10 [145] 14 [203] 11 [159] 13 [188] 10 [145] 2-spool position vlve with hydrulic end position r [psi] 7 [101] 14 [203] 8 [116] 8 [116] 5 [72] ilot oil supply internl (with symols C, F, G, H,,, V, Z, S 4) ) r [psi] 7.5 [109] 5) 4.5 [65] 6) 4.5 [65] 6) 4.5 [65] 6) 4.5 [65] 6) Free flow cross-sections in zero position with symols Q, V nd W Symol Q ; mm 2 [inch 2 ] 13 [0.02] 32 [0.05] 78 [0.121] 83 [0.129] 78 [0.121] Symol V ; mm 2 [inch 2 ] 13 [0.02] 32 [0.05] 73 [0.113] 83 [0.129] 73 [0.113] ; mm 2 [inch 2 ] 13 [0.02] 32 [0.05] 84 [0.13] 83 [0.129] 84 [0.13] Symol W ; mm 2 [inch 2 ] 2.4 [0.004] 6 [0.009] 10 [0.015] 14 [0.022] 20 [0.031] 3) ilot oil supply internl: With higher pilot pressure, use of pressure reducing vlve "D3" is required (if it is not used pilot pressure = operting pressure t the port). In connection with version "H", the pressure reducing vlve "D3" is lso required. Externl pilot oil supply: In connection with version "H-", complince with the mximum pilot pressure must e ensured y pproprite mesures (e.g. protection of the seprte pilot oil circuit y using pressure relief vlve)! 4) Symol S only for NG16 5) For symols C, F, G, H,,, V, Z, n internl pilot oil supply is only possile if the flow from to in the centrl position (for 3-spool position vlve) or while crossing the centrl position (for 2-spool position vlve) is so lrge tht the pressure differentil of to reches vlue of t lest 7.5 r [109 psi] nd the pilot oil return is implemented externlly. 6) For symols C, F, G, J, H,,, V, Z, S 4) y mens of prelod vlve (not NG10) or correspondingly high flow. (Determintion of the required flow, see "relod vlve" chrcteristic curves on pge 38.) For NG10, check vlve with crcking pressure of 7.5 r [109 psi] is to e provided in the return line to the tnk. he pilot oil return must e implemented externlly. RE 24802, edition: 2016-12, osch Rexroth G
16/40 WEH Directionl spool vlve echnicl dt (For pplictions outside these prmeters, plese consult us!) hydrulic Size NG 10 16 25 "W.H 22" ilot volume for switching process 3-spool position vlve, spring-centered cm 3 [inch 3 ] 2.04 [0.124] 2-spool position vlve cm 3 [inch 3 ] 4.08 [0.249] 3-spool position vlve, pressure-centered from zero position in switching position "" from switching position "" in zero position from zero position in switching position "" from switching position "" in zero position 5.72 [0.349] 11.45 [0.699] ype WEH cm 3 [inch 3 ] 2.83 [0.173] 7.64 [0.466] 15.28 [0.932] 25 "W.H 25" 14.2 [0.866] 28.4 [1.733] 7.15 [0.436] 32 29.4 [1.794] 58.8 [3.588] 14.4 [0.879] ype WEH cm 3 [inch 3 ] 2.9 [0.177] 7.0 [0.427] 15.1 [0.921] ype WEH cm 3 [inch 3 ] 5.72 [0.349] ype WEH cm 3 [inch 3 ] 2.83 [0.173] 14.15 [0.863] 5.73 [0.349] 29.4 [1.794] 14.4 [0.879] ilot flow for shortest switching time, pprox. l/min [US gpm] 35 [9.2] 35 [9.2] 35 [9.2] 35 [9.2] 45 [11.9] Hydrulic fluid Clssifiction Suitle seling Stndrds Dt sheet mterils Minerl oils HL, HL, HLD, HVL, HVLD NR, FKM DIN 51524 90220 io-degrdle Insolule in wter HEG FKM ISO 15380 HEES FKM 90221 Solule in wter HEG FKM ISO 15380 Flme-resistnt Wter-free HFDU (glycol se) FKM HFDU (ester se) FKM ISO 12922 90222 HFDR FKM Importnt informtion on hydrulic fluids: io-degrdle nd flme-resistnt: If these hydrulic fluids re For further informtion nd dt on the use of other hydrulic used, smll mounts of dissolved zinc my get into the hydrulic fluids, plese refer to the dt sheets ove or contct us. system. ( mg zinc per pole tue). here my e limittions regrding the technicl vlve dt (temperture, pressure rnge, life cycle, mintennce intervls, etc.). he ignition temperture of the hydrulic fluid used must e 50 K higher thn the mximum solenoid surfce temperture. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 17/40 Switching times ilot pressure r [psi] 70 [1015] 210 [3046] 250 [3626] Spring NG10 NG16 NG25 ("4W.H 22") NG25 ("4W.H 25") NG32 Without throttle insert ms 40 60 40 60 20 30 With throttle insert ms 60 90 50 70 20 30 Without throttle insert ms 50 80 40 60 50 80 With throttle insert ms 110 130 80 100 50 80 Without throttle insert ms 40 70 40 60 50 70 With throttle insert ms 140 160 80 110 50 70 Without throttle insert ms 70 100 50 70 100 130 With throttle insert ms 200 250 120 150 100 130 Without throttle insert ms 80 130 70 100 140 160 With throttle insert ms 420 560 230 350 140 160 ON OFF Notes: Switching times = Contcting t the pilot control vlve until strt of opening of the control edge in the min vlve nd chnge in the control spool stroke y 95%) he switching times re mesured ccording to ISO 6403 with HL46, ϑ oil = 40 C ± 5 C [104 F ±9 F]. With different oil tempertures, vritions re possile! he switching times were determined using DC solenoids. hey decrese y pprox. 20 ms if C solenoids re used. he shut-off of the solenoids cretes voltge peks, which cn e reduced y the use of suitle diodes. he switching times increse y pprox. 30 ms if the pressure reducing vlve "D3" is used. he switching times hve een determined under idel conditions nd my differ in the system, depending on the ppliction conditions. RE 24802, edition: 2016-12, osch Rexroth G
18/40 WEH Directionl spool vlve Chrcteristic curves: NG10 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) ressure differentil in r [psi] 22 20 18 16 14 12 10 8 6 4 2 0 0 p-q V chrcteristic curves 8 7 6 5 4 3 2 1 20 40 60 80 100 120 140 160 Flow in l/min [US gpm] Symol Spool position Zero position 1) 1) E,, D, Q, V, W, Z 1 1 3 5 F 1 3 1 4 3 6 G, 4 2 4 7 8 H, C 3 3 1 7 1 5 5 J, K 1 2 1 6 L 2 2 1 4 2 M 3 3 2 5 3 1 2 7 5 7 R 1 2 3 U 2 2 3 6 6, 1 1 1) he pressure differentil refers to the use of port. If port 1 is used in ddition, the pressure differentil my e lower. If only port 1 is used, the reltions nd my e reversed. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 19/40 erformnce limits: NG10 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) 2-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring end position in the min vlve 1) (with p St min = 12 r [174 psi]) C, D, K,, Z 160 [42] 160 [42] 160 [42] 160 [42] 160 [42] externl hydrulic end position in the min vlve HC, HD, HK, HZ, H 160 [42] 160 [42] 160 [42] 160 [42] 160 [42] 1) If the pilot pressure fils, the function of the return spring is no longer gurnteed with the specified flow vlues! 3-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring-centered E, J, L, M, Q, 160 [42] 160 [42] 160 [42] 160 [42] 160 [42] U, V, W, R F, 160 [42] 120 [32] 100 [26] 90 [20] 90 [20] G, 160 [42] 160 [42] 160 [42] 130 [34] 120 [32] H 160 [42] 160 [42] 120 [32] 110 [29] 100 [26] Importnt informtion see pge 28. RE 24802, edition: 2016-12, osch Rexroth G
20/40 WEH Directionl spool vlve Chrcteristic curves: NG16 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) ressure differentil in r [psi] [406] [250] [300] [250] [200] [150] [100] [50] [0] 28 24 20 16 12 8 4 0 0 p-q V chrcteristic curves 9 8 50 100 150 200 250 300 [0] [5] [10] [15] [20] [25] [30] [35] [40] [45] [50] [55] [60] [65] [70] [75] [79.2] Flow in l/min [US gpm] 10 7 6 5 4 3 2 1 Symol Spool position Zero position D, E, 1 1 3 3 F 1 2 5 5 4 3 G 4 1 5 5 7 C, H 1 1 5 6 2 4 4 K, J 2 2 6 6 3 L 2 2 5 4 3 M 1 1 3 4 2 1 3 6 5 Symol Spool position Zero position Q 1 1 6 6 R 2 4 7 S 3 3 3 9 4 1 5 5 7 U 2 2 3 4 6 V, Z 1 1 6 6 10 8 8 W 1 1 3 4 osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 21/40 erformnce limits: NG16 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) 2-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring end position in the min vlve (with p pilot min = 12 r [174 psi]) C, D, K,, Z 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] externl spring end position in the min vlve 1) C 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] D, 300 [79] 270 [71] 260 [68] 250 [66] 230 [60] K 300 [79] 250 [66] 240 [63] 230 [60] 210 [55] Z 300 [79] 260 [68] 190 [50] 180 [47] 160 [42] externl hydrulic end position in the min vlve HC, HD, HK, HZ, H 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] 3-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring-centered E, H, J, 300 [79] 300 [79] 300 [79] 300 [79] 300 [79] L, M, Q, U, W, R F, 300 [79] 250 [66] 180 [47] 170 [45] 150 [39] G, 300 [79] 300 [79] 240 [63] 210 [55] 190 [50] S 300 [79] 300 [79] 300 [79] 250 [66] 220 [58] V 300 [79] 250 [66] 210 [55] 200 [53] 180 [47] externl pressure-centered (t minimum pilot pressure of 16 r [232 psi]) ll 300 [79] 300 [79] 300 [79] symols 2) 1) If the specified flow vlues re exceeded, the function of the return spring is no longer gurnteed if the pilot pressure fils! 2) With symol V, the pilot control vlve is not required for flows >160 l/min [42 US gpm]. Importnt informtion see pge 28. RE 24802, edition: 2016-12, osch Rexroth G
22/40 WEH Directionl spool vlve Chrcteristic curves: NG25 ("W.H 22") (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) [290] [275] 20 p-q V chrcteristic curves 9 ressure differentil in r [psi] [250] [225] [200] [175] [150] [125] [100] [75] [50] 18 16 14 12 10 8 6 4 8 7 6 5 4 3 2 1 [25] 2 [0] 0 0 50 100 150 200 250 300 350 400 [0] [10] [20] [30] [40] [50] [60] [70] [80] [90] [100] [110] Flow in l/min [US gpm] Symol Spool position E, D 2 2 3 5 J, Q, K 2 2 4 6 M, W 1 1 3 5 H, V, C, Z 1 1 4 6 F 1 2 4 5 G 3 4 5 6 R 1 2 2 L 2 2 4 5 U 2 2 2 6 2 2 2 7 4 4 5 6 Symol Zero position F 2 4 G, 9 H 3 L 7 U 6 J 8 8 4 6 V, Z 8 osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 23/40 erformnce limits: NG25 ("W.H 22") (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) 2-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring end position in the min vlve (with p pilot min = 11 r / 14 r [159 / 203 psi]) C, D, K,, Z externl spring end position in the min vlve 1) C D, K Z 350 [92] 215 [57] 300 [79] 320 [84] 150 [39] 290 [76] 250 [66] 400 [105] 120 [32] 260 [68] externl hydrulic end position in the min vlve HC, HD, HK, HZ, H HC./O, HD./O, HK./O, HZ./O HC./OF, HD./ OF, HK./OF, HZ./OF 200 [53] 320 [84] 100 [26] 160 [42] 3-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring-centered E, J, L, M, Q, U, W, R H G 400 [105] F V 400 [105] 350 [92] 270 [71] 300 [79] 300 [79] 270 [71] 300 [79] 250 [66] 175 [46] 240 [63] 240 [63] 180 [47] 260 [68] 200 [53] 130 [34] 220 [58] 200 [53] 170 [45] 230 [61] 180 [47] 110 [29] 160 [42] 160 [42] 110 [29] 1) If the specified flow vlues re exceeded, the function of the return spring is no longer gurnteed if the pilot pressure fils! Importnt informtion see pge 28. RE 24802, edition: 2016-12, osch Rexroth G
24/40 WEH Directionl spool vlve Chrcteristic curves: NG25 ("W.H 25") (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) ressure differentil in r [psi] p-q V chrcteristic curves 22 20 18 16 14 12 10 8 6 4 8 7 6 5 4 3 2 1 2 0 100 200 300 400 500 600 650 Flow in l/min [US gpm] Symol Spool position Zero position 1) 1) E,, D 1 1 3 4 F 1 1 2 4 2 5 G, 1 1 2 5 7 H 1 1 2 5 2 2 4 C 1 1 2 5 J 1 1 2 5 6 5 K 1 1 2 5 L 1 1 2 4 5 M 1 1 3 4 1 1 3 5 3 5 Q 1 1 2 3 R 1 1 3 U 1 1 2 5 5 V 1 1 2 5 8 7 Z 1 1 2 5 W 1 1 3 4 8 Symol R, spool position osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 25/40 erformnce limits: NG25 ("W.H 25") (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) 2-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring end position in the min vlve (with p pilot min = 13 r [188 psi]) C, D, K,, Z externl spring end position in the min vlve 1) C D, K Z 650 [172 ] 650 [172 ] 400 [105 ] 420 [111] 650 [172 ] 350 [92] 370 [98] 480 [127 ] externl hydrulic end position in the min vlve HC, HD, HK, HZ, H HC./O, HD./O, HK./O, HZ./O HC./OF, HD./ OF, HK./OF, HZ./OF 650 [172 ] 650 [172 ] 300 [79] 320 [84] 400 [105 ] 1) If the specified flow vlues re exceeded, the function of the return spring is no longer gurnteed if the pilot pressure fils! 3-spool position vlves q V mx in l/min [US gpm] Operting pressure p mx in r [psi] Symol 70 [1015] 140 [2030] 210 [3046] 280 [4061] 350 [5076] externl spring-centered E, L, M, Q, U, W G, 400 [105 ] F 650 [172 ] H J 650 [172 ] V 650 [172 ] R 400 [105 ] 550 [145] 650 [172 ] 550 [145] 550 [145] 400 [105 ] 430 [113] 550 [145] 650 [172 ] 430 [113] 400 [105 ] externl pressure-centered (t minimum pilot pressure of 18 r [261 psi]) E, F, H, J, L, M,, Q, R, U, V, W G, 400 [105 ] 400 [105 ] externl pressure-centered (with pilot pressure > 30 r [435 psi]) G, 400 [105 ] 400 [105 ] 330 [87] 400 [105 ] 600 [158 ] 330 [87] 350 [92] 650 [172 ] 400 [105 ] 650 [172 ] 400 [105 ] 300 [79] 360 [95] 520 [137 ] 300 [79] 310 [82] 580 [153 ] 650 [172 ] 400 [105 ] 650 [172 ] Importnt informtion see pge 28. RE 24802, edition: 2016-12, osch Rexroth G
26/40 WEH Directionl spool vlve Chrcteristic curves: NG32 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) p-q V -chrcteristic curves Symol E, R nd W ressure differentil in r [psi] [261] [200] [150] [100] [50] [0] 18 16 14 1 2 12 10 8 6 3 4 4 2 0 0 100 300 500 900 1080 [0] [40] [80] [120] [160] [200] [240] [285] Symol Spool position E 4 4 3 2 R 4 4 3 1 W 4 4 3 2 Flow in l/min [US gpm] ressure differentil in r [psi] [261] [200] [150] [100] [50] [0] p-q V chrcteristic curves Symol G nd 18 5 16 14 6 12 10 8 7 8 6 4 2 0 0 100 300 500 900 1080 [0] [40] [80] [120] [160] [200] [240] [285] Symol Spool position G 7 8 7 5 6 7 8 7 5 6 Flow in l/min [US gpm] osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 27/40 erformnce limits: NG32 (mesured with HL46, ϑ Oil = 40 ±5 C [104 ±9 F]) 2-spool position vlves q V mx in l/min [US gpm] Symol 70 [1015] Operting pressure p mx in r [psi] 140 [2030] 210 [3046] externl spring end position in the min vlve (with p St min = 10 r [145 psi]) C, D, K,, Z 1100 [290] 1040 [275] 860 [227] 280 [4061] 750 [198] externl spring end position in the min vlve 1) C 1100 [290] D, 1100 [290] K 1100 [290] Z 1100 [290] 1040 [275] 1040 [275] 1040 [275] 1040 [275] 860 [227] 540 [142] 860 [227] 860 [227] 800 [211] 480 [127] 500 [132] [185] externl hydrulic end position in the min vlve HC, HD, HK, HZ, H 1100 [290] 1040 [275] 860 [227] 750 [198] 350 [5076] 680 [179] [185] 420 [111] 650 [172] 680 [179] 3-spool position vlves q V mx in l/min [US gpm] Symol 70 [1015] externl spring-centered E, J, L, M, Q, R, U, W 1100 [290] G,, H, F, 900 [238] V 1100 [290] Operting pressure p mx in r [psi] 140 [2030] 1040 [275] 900 [238] 1000 [264] 210 [3046] 860 [227] 800 [211] 680 [179] externl pressure-centered (t minimum pilot pressure of 8.5 r [123 psi]) ll symols 1100 [290] 1040 [275] 860 [227] 280 [4061] 750 [198] 650 [172] 500 [132] 750 [198] 350 [5076] 680 [179] 680 [179] 1) If the specified flow vlues re exceeded, the function of the return spring is no longer gurnteed if the pilot pressure fils! Importnt informtion see pge 28. RE 24802, edition: 2016-12, osch Rexroth G
28/40 WEH Directionl spool vlve erformnce limits: importnt informtion Notice (pplies to ll sizes): he specified switching power limits pply to the use with two directions of flow (e.g. from to nd simultneous return flow from to t rtio of 1:1). Due to the flow forces cting within the vlves, the dmissile switching power limit my e considerly lower with only one direction of flow (e.g. from to while port is locked, with flow in the sme or in different directions)! In such use cses, plese consult us! he switching power limit ws estlished while the solenoids were t operting temperture, t 10% undervoltge, nd without tnk preloding. NG16 NG25 ("W.H 22") NG25 ("W.H 25") NG32 With pilot oil supply internl, prelod vlve hs to e used for flows < 160 l/min [42 US gpm] due to the negtive overlp of the symols C, Z nd HC, HZ. 4/3 directionl vlves with pressure centering of the control spool in the min vlve cn e used ove the indicted performnce limit. In this cse, higher pilot pressure is required (vlues see performnce limits of the corresponding size). With pilot oil supply internl, sufficient flow needs to e ensured due to the negtive overlp of symols F, G, H,, S nd (for determintion of the required flow, see "relod vlve" chrcteristic curves (pge 38). If the required flow is not reched, prelod vlve hs to e used (see pge 15). With pilot oil supply internl, prelod vlve hs to e used for flows < 180 l/min [47.5 US gpm] due to the negtive overlp of symols Z, HZ nd V. With pilot oil supply internl, sufficient flow needs to e ensured due to the negtive overlp of symols C, HC, F, G, H, nd (for determintion of the required flow, see "relod vlve" chrcteristic curves (pge 38). If the required flow is not reched, prelod vlve hs to e used (see pge 15). With pilot oil supply internl, prelod vlve hs to e used for flows < 180 l/min [47.5 US gpm] due to the negtive overlp of symols Z, HZ nd V. 4/3 directionl vlves with pressure centering of the control spool in the min vlve cn e used ove the indicted performnce limit. In this cse, higher pilot pressure is required (vlues see performnce limits of the corresponding size). With pilot oil supply internl, sufficient flow needs to e ensured due to the negtive overlp of symols C, HC, F, G, H, nd (for determintion of the required flow, see "relod vlve" chrcteristic curves (pge 38). If the required flow is not reched, prelod vlve hs to e used (see pge 15). With pilot oil supply internl, prelod vlve hs to e used for flows < 180 l/min [47.5 US gpm] due to the negtive overlp of symols Z, HZ nd V. 4/3 directionl vlves with pressure centering of the control spool in the min vlve cn e used ove the indicted performnce limit. In this cse, higher pilot pressure is required (vlues see performnce limits of the corresponding size). With pilot oil supply internl, sufficient flow needs to e ensured due to the negtive overlp of symols C, HC, F, G, H, nd (for determintion of the required flow, see "relod vlve" chrcteristic curves (pge 38). If the required flow is not reched, prelod vlve hs to e used (see pge 15). osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 29/40 Dimensions: NG10 (dimensions in mm [inch]) 11 5 6 2.3 14 232 [9.13] (205 [8.07]) 3.1 44 15 3.2 4 35 87 40 92 8 2.1; 2.2 9 1 20 12 13 6,6 11 25,5 168 30,5 13,5 27 108 10.1 71 73 F1 F2 1 F4 F3 0,01/100 [0.0004/4.0] Rzmx 4 Required surfce qulity of the vlve contct surfce Item explntions, supltes, nd vlve mounting screws see pge 34. Notice: he dimensions re nominl dimensions which re suject to tolernces. RE 24802, edition: 2016-12, osch Rexroth G
30/40 WEH Directionl spool vlve Dimensions: NG16 (dimensions in mm [inch]) 11 5 6 2.3 14 232 [9.13] (205 [8.07]) 3.1 15 3.2 4 8 92 2.1; 2.2 20 43 40 9 1 12 97 13 27 17 56 156 64 164 3 3 19 82 18 16 15 11 18 6,6 11 21 142 93 12 F1 L F5 F2 G1 94 10.2 F4 G2 F6 F3 Item explntions, supltes, nd vlve mounting screws see pge 34. Notice: he dimensions re nominl dimensions which re suject to tolernces. 0,01/100 [0.0004/4.0] Rzmx 4 Required surfce qulity of the vlve contct surfce osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 31/40 Dimensions: NG25 ("W.H 22") (dimensions in mm [inch]) 11 5 6 2.3 232 [9.13] (205 [8.07]) 14 [0.59] 3.2 2.1; 2.2 [4.33] 12 3.1 4 8 9 1 110 [0.78] 20 40 92 [3.62] 15 [1.57] [0.55] 14 193 [7.60] 241[9.49] [0.157] 4 41 [1.61] 6 [Ø0.24] 19 13 14 [Ø0.55] 20 [Ø0.79] [0.55] 17,5 [0.69] 180 [7.09] [4.61] 117 14 F1 L 1) F5 G1 F2 [4.72] 120 1) ort L only for vlves with pressurecentered zero position Item explntions, supltes, nd vlve mounting screws see pge 34. 10.3 Notice: he dimensions re nominl dimensions which re suject to tolernces. F4 G2 F6 F3 0,01/100 [0.0004/4.0] Rzmx 4 Required surfce qulity of the vlve contct surfce RE 24802, edition: 2016-12, osch Rexroth G
32/40 WEH Directionl spool vlve Dimensions: NG25 ("W.H 25") (dimensions in mm [inch]) 11 5 6 2.3 14 232 [9.13] (205 [8.07]) 3.1 15 3.2 4 41 126 92 2.1; 2.2 1 40 20 8 9 12 19 225 279 297 324,5 332 324,5 27,5 13 15 4 6 19 10.3 17 18 20 14 16 21 195 117 14 F1 L 1) F5 G1 F2 120 F4 G2 F6 F3 1) ort L only for vlves with pressurecentered zero position Item explntions, supltes, nd vlve mounting screws see pge 34. Notice: he dimensions re nominl dimensions which re suject to tolernces. 0,01/100 [0.0004/4.0] Rzmx 4 Required surfce qulity of the vlve contct surfce osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 33/40 Dimensions: NG32 (dimensions in mm [inch]) 11 5 6 2.3 232 [9.13] (205 [8.07]) 3.1 4 14 [0.59] 15 152 [5.98] 17 3.2 2.1; 2.2 12 21,5 [0.85] 286,5 362 [14.25] 391 [15.39] 391 [15.39] 406 [15.98] [1.93] 49 8 9 1 13 15 16 6 [Ø0.24] 19 [0.78] 20 40 92 [3.62] [1.57] 4 [0.157] 0,2 +0,3 [0.0079 +0.0118 ] 18 19 33 [Ø1.30] 22 [Ø0.87] 23 [0.91] 257 [10.12] [7.76] 197 20,5 [0.81] F1 L F5 G1 F2 [7.87] 200 10.4 F4 G2 F6 F3 Item explntions, supltes, nd vlve mounting screws see pge 34. Notice: he dimensions re nominl dimensions which re suject to tolernces. 0,01/100 [0.0004/4.0] Rzmx 4 Required surfce qulity of the vlve contct surfce RE 24802, edition: 2016-12, osch Rexroth G
34/40 WEH Directionl spool vlve Dimensions 1 Min vlve 2 ilot control vlve type 4WE 6 (dt sheet 23208): 2.1 ilot control vlve type 4WE 6 D (1 solenoid) for min vlves with symols C, D, K, Z symols HC, HD, HK, HZ ilot control vlve type 4WE 6 J... (1 solenoid "") for min vlves with symols E, F, etc., spring return ilot control vlve type 4WE 6 M... (1 solenoid "") for min vlves with symols HE, HF, etc., hydrulic control spool return 2.2 ilot control vlve type 4WE 6... (1 solenoid) for min vlves with symol symol H ilot control vlve type 4WE 6 J... (1 solenoid "") for min vlves with symols E, F, etc., spring return ilot control vlve type 4WE 6 M... (1 solenoid "") for min vlves with symols HE, HF, etc., hydrulic control spool return 2.3 ilot control vlve type 4WE 6J (2 solenoids) for min vlves with 3 spool positions, spring-centered ilot control vlve type 4WE 6 M (2 solenoids) for min vlves with 3 spool positions, pressure-centered 3.1 Solenoid "" 3.2 Solenoid "" 4 Conceled mnul override "N9" ctution of the mnul override is only possile up to tnk pressure of pprox. 50 r. void dmge to the ore of the mnul override! (Specil tool for the opertion, seprte order, mteril no. R900024943). When the mnul override is locked, the opertion of the solenoid must e prevented! Simultneous ctution of the solenoids must e prevented. 5 Dimension for vlve with DC solenoid 6 Dimension () for vlve with C solenoid 8 Switching time djustment (wrench size 6), optionl 9 ressure reducing vlve, optionl 10.1 Mchined vlve contct surfce; porting pttern ccording to ISO 4401-05-05-0-05 nd NF3.5.1 R2-D05 10.2 Mchined vlve contct surfce; porting pttern ccording to ISO 4401-07-07-0-05 nd NF3.5.1 R2-D07 10.3 Mchined vlve contct surfce; porting pttern ccording to ISO 4401-08-08-0-05 nd NF3.5.1 R2-D08 10.4 Mchined vlve contct surfce; porting pttern ccording to ISO 4401-10-09-0-05 nd NF3.5.1 R2-D10 11 Nme plte pilot control vlve 12 Nme plte complete vlve 13 Sel rings 14 Spce required for removing the mting connector 15 2-spool position vlves with spring end position in the min vlve (symols, C, D, K, Z) 16 2-spool position vlves with spring end position in the min vlve (symols, ) 17 3-spool position vlves, spring-centered; 2-spool position vlves with hydrulic end position in the min vlve 18 3-spool position vlves, pressure-centered 19 Locking pin Supltes (seprte order) with porting pttern ccording to ISO 4401 see dt sheet 45100. Vlve mounting screws (seprte order) NG10: 4 hexgon socket hed cp screws, metric ISO 4762 - M6 x 45-10.9-flZn-240h-L (friction coefficient µ totl = 0.09 0.14); tightening torque M = 12.5 Nm [9.2 ft-ls] ±10%, mteril no. R913000258 4 hexgon socket hed cp screws, UNC 1/4-20 UNC x 1 3/4" SM-574 upon request NG16: 4 hexgon socket hed cp screws, metric ISO 4762 - M10 x 60-10.9-flZn-240h-L (friction coefficient µ totl = 0.09 0.14); tightening torque M = 58 Nm [42.8 ft-ls] ±10%, mteril no. R913000116 2 hexgon socket hed cp screws, metric ISO 4762 - M6 x 60-10.9-flZn-240h-L (friction coefficient µ totl = 0.09 0.14); tightening torque M = 12.5 Nm [9.2 ft-ls] ±10%, mteril no. R913000115 4 hexgon socket hed cp screws, UNC 3/8-16 UNC x 2 1/4" SM-574 upon request 2 hexgon socket hed cp screws, UNC 1/4-20 UNC x 2 1/4" SM-574 upon request NG25: 6 hexgon socket hed cp screws, metric ISO 4762 - M12 x 60-10.9-flZn-240h-L (friction coefficient µ totl = 0.09 0.14); tightening torque M = 130 Nm [95.9 ft-ls] ±10%, mteril no. R913000121 6 hexgon socket hed cp screws, UNC 1/2-13 UNC x 2 1/2" SM-574 upon request NG32: 6 hexgon socket hed cp screws, metric ISO 4762 - M20 x 80-10.9-flZn-240h-L (friction coefficient µ totl = 0.09 0.14); tightening torque M = 430 Nm [317.2 ft-ls] ±10%, mteril no. R901035246 6 hexgon socket hed cp screws, UNC 3/4-10 UNC x 3 1/4" SM-574 upon request osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 35/40 Stroke setting, mounting options (dimensions in mm [inch]) he stroke of the control spool is limited y the stroke setting (1). he control spool stroke is shortened y loosening the lock nut (2) nd clockwise rottion of the djustment spindle (3). he control chmer (4) must e depressurized for this. 5 1 L4 L3 4 2 3 NG L4 10 6.5 [0.26] 16 10 [0.39] 25 ("W.H 22") 9.5 [0.37] 25 ("W.H 25") 12.5 [0.49] 32 15 [0.59] More dimensions see elow nd pge 36. 5 djustment rnge NG10: 1 rottion = 1 mm [0.0394 inch] djustment trvel NG16 nd 32: 1 rottion = 1.5 mm [0.0591 inch] djustment trvel Stroke limittion on side L3 Stroke limittion on side L3 L1 L2 L3 L2 L1 L1 L3 L2 3-spool position vlve 1) spring-centered pressure-centered Mounting options Ordering code NG L1 L2 L3 L1 L2 L3 10 90 [3.54] 144 [5.67] 234 [9.21] 16 100 [3.94] 200 [7.87] 300 [11.81] Stroke setting on vlve side nd 10 25 2) 96 [3.77] 241 [9.49] 337 [13.27] 25 3) 123 [4.84] 276 [10.87] 399 [15.71] 32 133 [5.24] 344 [13.54] 477 [18.78] 10 90 [3.54] 106 [4.17] 196 [7.72] 16 100 [3.94] 156 [6.14] 256 [10.08] Stroke setting on 11 vlve side 25 2) 96 [3.77] 193 [7.60] 289 [11.38] 25 3) 123 [4.84] 225 [8.86] 348 [13.70] 32 133 [5.24] 287 [11.30] 420 [16.54] 10 52 [2.05] 144 [5.67] 196 [7.72] 16 56 [2.20] 200 [7.87] 256 [10.08] 81 [3.19] 200 [7.87] 281 [11.06] Stroke setting on vlve side 12 25 2) 48 [1.89] 241 [9.49] 289 [11.38] 25 3) 72 [2.83] 276 [10.87] 348 [13.70] 107 [4.21] 276 [10.87] 283 [11.14] 32 76 [2.99] 344 [13.54] 420 [16.54] 120 [4.72] 344 [13.54] 464 [18.27] RE 24802, edition: 2016-12, osch Rexroth G
36/40 WEH Directionl spool vlve Stroke setting, mounting options (dimensions in mm [inch]) Mounting options Ordering code NG Stroke setting on vlve side nd Stroke setting on vlve side Stroke setting on vlve side 10 11 12 10 2-spool position vlve Spring end position Hydrulic end position, C, D, K, Z, HC, HD, HK, HZ, H L1 L2 L3 L1 L2 L3 L1 L2 L3 90 [3.54] 144 [5.67] 234 [9.21] 90 [3.54] 144 [5.67] 234 [9.21] 16 25 2) 96 [3.78] 241 [9.49] 337 [13.27] 96 [3.78] 241 [9.49] 337 [13.27] 25 3) 32 10 90 [3.54] 16 100 [3.94] 96 25 2) [3.78] 123 25 3) [4.84] 32 133 [5.24] 10 52 [2.05] 106 [4.17] 180 [7.09] 193 [7.60] 253 [9.96] 316 [12.44] 144 [5.67] 196 [7.72] 280 [11.02] 289 [11.38] 376 [14.8] 449 [17.68] 196 [7.72] 16 25 2) 48 [1.89] 241 [9.49] 289 [11.38] 25 3) 32 96 [3.78] 193 [7.60] 289 [11.38] 52 [2.05] 80 [3.15] 48 [1.89] 100 [3.94] 105 [4.13] 144 [5.67] 200 [7.87] 241 [9.49] 276 [10.87] 344 [13.54] 196 [7.72] 280 [11.02] 289 [11.38] 376 [14.80] 449 [17.68] 90 [3.54] 100 [3.94] 96 [3.78] 123 [4.84] 133 [5.24] 90 [3.54] 100 [3.94] 96 [3.78] 123 [4.84] 133 [5.24] 52 [2.05] 56 [2.21] 48 [1.89] 72 [2.84] 76 [2.99] 144 [5.67] 200 [7.87] 241 [9.49] 276 [10.87] 344 [13.54] 106 [4.17] 156 [6.14] 193 [7.60] 225 [8.86] 287 [11.30] 144 [5.67] 200 [7.87] 241 [9.49] 276 [10.87] 344 [13.54] 234 [9.21] 300 [11.81] 337 [13.27] 399 [15.71] 477 [18.78] 196 [7.72] 256 [10.08] 289 [11.38] 348 [13.70] 420 [16.53] 196 [7.72] 256 [10.08] 289 [11.38] 348 [13.70] 420 [16.53] 1) With symol only version "11", with symol only version "12" possile. 2) Version "W.H 22" 3) Version "W.H 25" Notice: he dimensions re nominl dimensions which re suject to tolernces. osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 37/40 Switching time djustment he switching time of the min vlve (1) is influenced y using twin throttle check vlve (2) (type Z2FS 6; dt sheet 27506). 7 5 Modifiction of supply (3) to dischrge control (4): Remove the pilot control vlve (5) he plte (6) to ccept the sel rings stys in plce urn the switching time djustment (2) round its longitudinl xis nd put it ck, instll the pilot control vlve (5). 3 4 2 6 Notice: he modifiction my only e performed y uthorized specilists or t the fctory! ype.weh 10..4/ S ype.weh 10..4/ S2 1 ressure reducing vlve "D3" he pressure reducing vlve (8) hs to e used t pilot pressure ove 250 r [3626 psi] (with "WEH 22 ": 210 r [3046 psi]) nd with version "H". he secondry pressure is kept t constnt level of 45 r [652 psi]. Notice: If pressure reducing vlve "D3" (8) is used, "10" throttle insert hs to e instlled in chnnel of the pilot control vlve. he modifiction my only e performed y uthorized specilists or t the fctory! 8 7 ype.weh 10..4/ /..D3 RE 24802, edition: 2016-12, osch Rexroth G
38/40 WEH Directionl spool vlve relod vlve (not for NG10) In cse of vlves with depressurized circultion nd internl pilot oil supply, the instlltion of the prelod vlve (9) in chnnel of the min vlve is required in order to uild up the minimum pilot pressure. he pressure differentil of the prelod vlve is to e dded to the pressure differentil of the min vlve (see chrcteristic curves) to result in one totl vlue. he crcking pressure mounts to pprox. 4.5 r [65 psi]. 10 10 9.1 11 9.2 11 9.1 relod vlve 9.2 relod vlve 10 Min vlve 11 Suplte Notice: Series-production sttus, see ordering key on the nme plte. Size Mteril numer 4,5 Item 9.2 Item 9.1 16 R961009417 (up to component series 71) R961009415 (from component series 72) 25 ("W.H 22") R961009609 (up to component series 76) 25 ("W.H 25") R961009416 (up to component series 67) R961009166 (from component series 68) 32 R961009610 (up to component series 63) p q V chrcteristic curve (mesured with HL46, ϑ Oil = 40 C ± 5 C [104 F ±9 F]) ressure differentil in r [psi] [203] [150] [100] [50] [0] 14 12 10 8 6 4 2 0 0 1 2 4 3 100 200 300 400 500 600 1 NG16 2 NG25 ("W.H 25") 3 NG25 ("W.H 22") 4 NG32 [0] [20] [40] [60] [80] [100] [120] [140] [160] [185] Flow in l/min [US gpm] osch Rexroth G, RE 24802, edition: 2016-12
Directionl spool vlve WEH 39/40 roject plnning informtion he stipultions of the Mchinery Directive 2006/42/EC re to e dhered to! lese lso note dt sheet 08012 with informtion on MFd vlues nd shock nd virtion lods! Further informtion Directionl spool vlve (solenoid coil with UR-mrking ccording to UL 906) Dt sheet 23208 Supltes Dt sheet 45100 Inductive position switch nd proximity sensors (contctless) Dt sheet 24830 Hydrulic fluids on minerl oil sis Dt sheet 90220 Environmentlly comptile hydrulic fluids Dt sheet 90221 Flme-resistnt, wter-free hydrulic fluids Dt sheet 90222 Hexgon socket hed cp screw, metric/unc Dt sheet 08936 Hydrulic vlves for industril pplictions Operting instructions 07600- Directionl spool vlves nd directionl set vlves with electricl ctution nd Dt sheet 08010 M12x1 plug-in connection Use of non-electricl hydrulic components in n explosive environment (E) Dt sheet 07011 Selection of the filters www.oschrexroth.com/filter Informtion on ville spre prts www.oschrexroth.com/spc RE 24802, edition: 2016-12, osch Rexroth G
40/40 WEH Directionl spool vlve Notes osch Rexroth G Hydrulics Zum Eisengießer 1 97816 Lohr m Min, Germny hone +49 (0) 93 52 / 18-0 documenttion@oschrexroth.de www.oschrexroth.de his document, s well s the dt, specifictions nd other informtion set forth in it, re the exclusive property of osch Rexroth G. It my not e reproduced or given to third prties without its consent. he dt specified ove only serve to descrie the product. No sttements concerning certin condition or suitility for certin ppliction cn e derived from our informtion. he informtion given does not relese the user from the oligtion of own judgment nd verifiction. It must e rememered tht our products re suject to nturl process of wer nd ging. osch Rexroth G, RE 24802, edition: 2016-12