INSTALLATION INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION. KIT CONTENTS: QTY DESCRIPTION PART NUMBER 2 Front Spring 6110000 2 Rear Spring 6120000 1 Front Sway Bar 6190000S-F 1 Rear Sway Bar 6190000S-R 1 Hardware Kit 38144.320HK SPRINGS 1. Installation of any Hurst Spring Kit should be performed ONLY by a qualified mechanic with significant experience in removal and installation of suspension springs. 2. Never work on a vehicle unless it is properly supported. 3. Never use an impact gun to remove or install strut main shaft components. 4. Any Hurst part number starting with 611 is a front spring, any Hurst part number starting with 612 is a rear spring. 5. All springs should be installed with the Hurst logo right side up, and all original isolators, dampers, etc, should be retained. 6. For MacPherson Strut front suspension - mark the upper perch in relation to the lower before disassembly. Once the springs have been installed, verify the orientation has remained the same. 7. With installation complete, always check (and adjust if required): Alignment - Camber/Caster/Toe Tire/Wheel to Fender Clearance Brake line Clearance & Strain Relief Wheel Speed Sensor Wires & Strain Relief 8. No bump stop modifications are required. During installation, any bushed pivot points MUST be torqued with the full weight of the vehicle on the suspension. This is to avoid bushing pre-load. Failure to do so can result in uneven lowering, and bushing damage. This is easiest to accomplish with a drive-on type hoist. 9. Special Tools are required for the installation of this kit. Please refer to the factory service manual for a complete listing of special tools required, as well as the full procedure for safely removing the springs. Customer Assistance Helpline TEL: 707-544-4761 Hurst provides a telephone helpline staffed by knowledgeable people to assist you with answers to questions regarding any Hurst product. Mon - Fri, 6-5, Sat 7:30-5, PST HURST 1 www.hurst-shifters.com
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION. 1. Installation of any Hurst Sway Bar Kit should be performed ONLY by a qualified mechanic with significant experience in removal and installation of sway bars, who has access to factory torque specs. 2. Never work on a vehicle unless it is properly supported. 3. Use of a hoist and screw jack is highly recommended and will reduce the time required for installation. OEM FRONT SWAY BAR REMOVAL SWAY BARS 1) Begin by properly supporting the vehicle and removing the wheels. NEVER work under a vehicle only supported by a jack. 2) Remove the nuts which secure the outer links to the end of the factory bar. 3) Remove the bolts which secure the OEM sway bar pivot bushings to the subframe. 4) The OEM sway bar may now be removed by rotating and sliding it out towards the passenger side. HURST FRONT SWAY BAR INSTALLATION 1) Apply some lubricant (included in the hardware kit) to the ID (inside diameter) of the new front bushings. 2) Install the bushings onto the sway bar. 3) Install the newly assembled sway bar starting from the passenger side, and bolt to the subframe using the washers provided with the hardware kit and the OEM bolts. Do not tighten at this time. Please Note: Depending on the year/model, you may have to remove the drivers side outer tie rod from the steering knuckle to get the sway bar into its final position. 4) Fasten the outer links to the sway bar ends, using the OEM hardware. (Before choosing a hole location, please see setting guidelines on page three.) Do not tighten at this time. 5) Before final torque, double check to make sure everything is properly aligned and positioned. 6) Torque all sway bar fasteners to factory recommended settings. OEM REAR SWAY BAR REMOVAL 1) Remove the nuts which secure the outer links to the end of the factory bar. 2) Remove the bolts which secure the OEM sway bar pivot bushings to the subframe. 3) The OEM sway bar may now be removed by rotating and sliding it out. HURST 2 www.hurst-shifters.com
SWAY BARS, CONT. HURST REAR SWAY BAR INSTALLATION FRONT SETTING GUIDELINES 1) Apply some lubricant (included in the hardware kit) to the ID of the new rear bushings. 2) Install the bushings onto the sway bar. 3) Install the newly assembled sway bar, and bolt to the subframe using the washers provided with the hardware kit and the OEM bolts. Do not tighten at this time. 4) Fasten the outer links to the sway bar ends, using the OEM hardware. (Before choosing a hole location, please see setting guidelines on page four.) Do not tighten at this time. 5) Before final torque, double check to make sure everything is properly aligned and positioned. 6) Torque all sway bar fasteners to factory recommended settings. 7) Reinstall all wheels and torque to factory specification. Enjoy The Drive! FRONT FIRM SETTING Reduces Over-Steer Use under high traction Use on smooth roads / tracks FRONT SOFT SETTINGS Reduces Under-Steer Use under low traction Use on rough roads / tracks Softer, more compliant ride HURST 3 www.hurst-shifters.com
SWAY BARS, CONT. REAR SETTING GUIDELINES HURST STAGE ONE SUSPENSION KIT HURST WARRANTY INFORMATION This warranty covers the original purchasing consumer. This warranty is limited to repair or replacement by Hurst Performance of any Hurst Performance Product that fails because of a defect in materials or workmanship. Implied warranty: Any warranties implied by law are limited to the duration of this warranty, (except in those states where prohibited by law). HURST PERFORMANCE SPRING & SWAY BAR WARRANTY COVERAGE 1 Million Mile Structural / 90 Day Finish - All Hurst suspension springs and sway bars are covered for 1 million miles from the date of install against any structural defects, and 90 days against defects in finish to the original purchaser (not warranted against normal wear, misuse, or abuse). WHAT IS NOT COVERED Failure of a Hurst Performance Product due to misapplication, improper installation or maintenance, misuse, abuse, unauthorized repairs, accidents, or modifications to the original design. Removal or replacement costs. Damage to related components. Costs incurred due to downtime of vehicle, towing cost or transportation costs. Normal wear and tear, including stone chips, scratches made during install. Products used for racing except shifters. Melted shifter cables. Shipping costs. REAR FIRM SETTING Reduces Under-Steer Use under high traction Use on smooth roads / tracks REAR MID SETTING Depending on set up, balance out Under-Steer or Over Steer Use under normal driving Dry street driving REAR SOFT SETTINGS Reduces Over-Steer Use under low traction Use on rough roads / tracks Softer, more compliant ride PRODUCT RETURN PROCEDURE In the event a problem develops with a Hurst product, contact Hurst Performance Products: (707) 544-4761 or Fax (707) 303-9254. Ask for customer service. It may be determined the product will have to be returned to Hurst. A return material authorization number (RMA number) will be assigned to you. The retail store or customer should return the product in question, freight prepaid. It must be accompanied with the original purchase receipt and a clear description of the problem. If the product is determined to be defective and within the warranty period, Hurst will repair, replace or issue credit to the distributor at Hurst s option. Any repaired or replaced product will be returned to the sender freight prepaid via UPS. This limited warranty may give you specific legal rights, which may vary from state to state. HURST 4 www.hurst-shifters.com HURST 5 www.hurst-shifters.com
HURST 6 www.hurst-shifters.com