Quote Name: Name Shop Order Number: Sales Administration Use Only 417464-001 Serial Number/s: 700287-700346 Date: Date: xx/xx/xxxx CUSTOMER : Olsta/PneuTech Stock SALESPERSON : MODEL : Super Sander TM, Pneumatic - 3 Hoppers PART NO./DRAWING : 752-0077-2016 Tractor data as shown below will be used. Tractor Weight: 17000 Fifth Wheel Height: 49 Cab to Axle: N/A Front Axle Weight: 9500 Set Ahead: 24 After Frame: N/A Rear Axle Weight: 7500 Wheel Base: 187 Other: N/A SPEC CHG A. VESSEL 1) Capacity 1040 Cu. Ft. Pneumatic - 3 Hoppers 2) Tank Construction Smooth exterior, internal rings. 3) Baffles None 5454-H32 aluminum vessel. Hydro tested at 22.5 P.S.I. 45 degree hopper slope with weld on spun cones. 4) End Frame Welded 201stainless steel front and rear end frames, with aluminum pinned struts. 5) Internal weld finish W-1; Smoke and Discoloration Removed (Class I) 6) Shell finish Mill finish bulk trailer sheet 7) Manholes (3) 20 Civacon MM cast aluminum manholes, centered over each hopper with aluminum cam handles and nylon wear plates, replaceable wear plates under hold downs. White neoprene gaskets in manhole covers. Manholes hinge on curbside. 8) Documentation Unit tested with water. Professional cleaning is recommended prior to initial loading to avoid possible contamination of cargo. Maximum commodity temperature 180 degrees F. 9) Product Information Sand Page 1 of 6
10) Misc. Vessel All U-bolts to have protecting tubing applied B. TANK FITTINGS AND PIPING 1) Air Line Inlet 3" Sch. 10 aluminum line with welded 3" adapter streetside front of tank. One (1) BTI check valve with high temp gasket near P.T.O. inlet. One (1) BTI check valve with high temp gasket upstream of front hopper discharge. 2) Aeration (3) BTI SpinFlo TM aerators per hopper, with hopper saver wear plates included. 3" Aluminum air manifold, 2" hoses supplying air to aeration system. Air manifold located on curbside of trailer. 3) Aeration Control Valve 3" BTI BlackMaxx butterfly valve (ductile disc, black rubber seat), with powder coated steel handle. Located streetside to regulate airflow to air manifold line. 4) Proportioning/Pressure Control Valve 3" BTI BlackMaxx butterfly valve (ductile disc, black rubber seat), with powder coated steel handle. Located streetside to regulate airflow to product discharge line. 5) Blow-Down Line 3" Sch. 10 aluminum line with 3" BTI BlackMaxx butterfly valve (ductile disc, black rubber seat), with powder coated steel handle. Located streetside front of tank, with outlet terminating between the frame rails. Includes cam-on style pressure relief valve (18 PSI), Heil factory tested and wire sealed. 6) Top Air Line 3" BTI BlackMaxx TM butterfly valve (ductile disc, black rubber seat), with color coded steel handle. Page 2 of 6
7) Product Valve 5" BTI BlackMaxx butterfly valve (ductile disc, black rubber seat), with the BTI heavy duty HD aluminum handle. 8) Product Tee BTI SiphonFlow TM 5 x 4 heat treat alloy steel gravity tees. Zinc plated body and aluminum gravity door. 9) Product Line 4" Sch. 40 zinc plated steel line between hoppers. Rubber hose with stainless steel screw band clamp connectors between hoppers. 10) Rear Discharge Line 4 Sch 40 zinc plated cam-on under axle (straight pipe) with threaded steel coupler and aluminum dust plug 12) Load Line Not available 13) Gauges Two (2) liquid filled illuminated gauges, one tank pressure and one line pressure. Gauge pressure range 0-30 PSI. Located on streetside between number one and two hopper. 14) Miscellaneous None C. ACCESSORIES 1) Ladder Aluminum with serrated rungs and top step. Mounted at the center rear over the chassis frame. Ladder rails protrude up and over the rear of the vessel. Grab handle at located on chassis frame. 2) Walkway Adhesive backed skid-resistant tape between toe rails. 3) Hose Tubes (1) 8" x 21' long aluminum hose tube located streetside rear of tank. Cast aluminum door at rear. (1) 8" x 21' long aluminum hose tube located curbside rear of tank. Cast aluminum door at rear. 4) Tire Carrier Not available 5) Cabinet Not available 6) Hose Holder P.T.O. hose holder with mandrel located on roadside, just forward of the lower front strut pin. 7) Fenders (2) Aluminum single contour front fenders with galvanized steel support brackets. (2) Aluminum double contour rear fenders with galvanized steel support brackets 8) Splash Guard PneuTech Anti-sail and anti-spray for front. PneuTech Anti-sail and anti-spray for rear. Page 3 of 6
9) Lights 12 Volt Truck Lite grommet mount LED lamp system complying to FMVSS with conspicuity markings each side and rear. (2) Combination mid-tank clearance and turn signals, one each side. (1) Oval third stop light, located rear center of trailer. (2) LED Work lights. (1) mounted on curbside rear strut area between the struts and (1) mounted streetside on rear of front fender to illuminate product valves. 10) Wiring 12-volt system, 7-wire, molded harness throughout. "Plug-together" modular style harness. 7-way SAE J560 connector. 11) Document Holder Truck-Lite mounted roadside at landing gear, below pressure gauges. 12) Miscellaneous None Page 4 of 6
D. CHASSIS 1) Upper Fifth Wheel Hi-tensile steel, bolted and adjustable with 2" forged kingpin. 2) Landing Gear SAF-Holland Atlas 55, load bearing, two-speed leg assembly; includes streetside crank handle. Five year no lube performance guarantee, rated from -65 F to 225 F. Lift capacity of 55,000 pounds with 10 x 10 low profile sand shoes. SAF-Holland Black Armour corrosion protection coating Cross bracing and back bracing will be stainless steel (all parts will be black except for the bracing) Back brace not to exceed 23 ±2 from the landing leg (see image below). Fire Extinguisher Not Included 3 Suspension Hendrickson Intraax raised center axle AAT23K-RC air ride suspension & brake system, 71.5" track, parallel spindle, 23,000 lb. beam rating, 49" spacing, with single leveling valve. Generic suspension load scale mounted on vessel framing streetside above rear chassis frame. Galvanized hangers and bracing Axles painted DuPont Gray and prepped for tire inflation system. 4) Brake System WABCO 4S/2M ABS (4 wheel sensors 2 modulator valves). Constant power is standard on auxiliary (blue) center pin of SAE J560 7-way. Gladhands with serviceable in line filters. One (1) aluminum 2850 cu. in. air tank. System designed to meet FMVSS requirements. 5) Brake Chamber OEM brake chambers. 6) Brake Lining OEM HXS 20,000 lb. brake lining. Page 5 of 6
7) Slack Adjuster OEM slack adjusters. 8) Axles (2) Integral with air ride. 9) Oil Seals OEM oil seals and solid hub caps. 10) Paint Black DuPont Imron 5000 series paint on steel parts only. 11) Miscellaneous Reinforced steel tow hook at rear of trailer frame. E. HUBS AND DRUMS 1) Hubs (4) 10-stud, "Hub Pilot" (single nut mount) ADI hubs for outboard drums, parallel spindle and dual aluminum wheel-compatible stud length. Two-piece flanged wheel nuts. 2) Drums F. WHEELS Includes Hendrickson s HXL-7 wheel end warranty with SF synthetic grease hub lubrication. Note: Hendrickson HXL-7 requires sold hub caps. (4) Centrifuse - outboard mounted brake drums (16.5" x 7"). 1) Wheels 1) Tires G. TIRES H. MISCELLANEOUS (8) Alcoa Ultra One 24.5 x 8.25 Ten stud, hub piloted, clean buff wheels (8) Marathon LHT 11R24.5 (9874-0470) 1) Customer Supplied Parts None 2) Warranty See Heil Warranty document 3) Other Notes This Heil pneumatic tank trailer is designed and constructed for the highway transportation of dry granule and pulverized bulk commodities. It is not designed for hauling any type liquid or semi liquid (slurry) which may damage the unit and potentially cause personal injuries. 4) Miscellaneous Operational manual and informational CD is included and shipped with each trailer. Page 6 of 6