STATE OF MINNESOTA PRICING Bert's Truck Equipment of Moorhead

STATE OF MINNESOTA PRICING 11-30-17 Bert's Truck Equipment of Moorhead 1.0 Knapheide Utility/Service Bodies to fit 56, 60, 84 & 108 CA Chassis s Standard Features: Body Shell 14 gauge two-sided A40 galvanneal steel. Compartment top and back are one piece seamless design. All doors, door openings, drip rails, and other exposed steel edges to be hemmed for strength, safety and resistance to corrosion. Floor 12 gauge treadplate with 1 3/8 return flange on each side. Side compartment back panel overlaps and interlocks with floor flange, providing support for weight of side compartment. Understructure 50,000 yield 11 gauge high strength steel cross sills Tailgate 14 gauge two-sided A40 galvanneal steel double panel construction. Slam lockable style Doors 20 gauge two-sided A40 galvanneal steel double panel doors with hat section reinforcements. Hinges Corrosion resistant all stainless steel continuous hinges provide full length support for the doors and pry-proof security with a built-in weather shield. Hinge to be spot welded to the door frame supported with a six year warranty. Rotary Latches Automotive rotary latches rivet-less design Rotary latch is slam-latchable Latching cam to be elongated to allow the latch to move vertically relative to the lockstrike to prevent torsional damage. Door Strikers Adjustable striker affixed to door frame with screws. ( Door Seals Automotive bulb type neoprene door seals to be installed by the manufacturer of the body on all door frames. Door Retainer Double spring over center door retainers on all vertical doors, retains doors in positive open or closed position. Shelving 18 gauge bright spangled galvanized shelves with hemmed dividers on 4 centers. Minimum 250 lbs. capacity rated. Exterior Prime Paint Body is completely immersed in electrodeposition gray epoxy prime paint featuring a zinc phosphate pre-coat and seal for additional corrosion protection. Prime paint is oven cured to provide a hard durable finish. Interior Paint Interior painted mid-gloss, mar resistant, light gray finish. Interior painted mid-gloss, mar resistant, light gray finish. Undercoating Body is completely undercoated by the manufacturer of the body using minimum five (5) mils of water base acrylic. Warranty The following items to be covered by minimum six (6) year limited warranty to first owner/user of record. No Rust-Thru GuaranNo Rust-Thru Guarantee

Continuous Door Hinge Guaranteed not to fail to operate or come off product. Latches and Lock Cylinders Guarantee against failure. Shelves Guaranteed not to fail in bending under maximum 250lb. rated load. Base Price includes, Standard Body as provided by Knapheide with Standard Shelving Package. All prices are FOB Moorhead and are Load Out, Prime painted Note: Chassis Specific Mounting Kit not included in base price! 96 Bodies to fit Single Wheel 56 CA Chassis 1.0-1 Knapheide, 596, 696, 796, Standard Models 3,469.00 (78 wide, 97 ¼ long, 40 high, 49 cargo area) 1.0-2 Low profile model (LPJ) 37.5 3,469.00 1.0-3 Knapheide 596F, 696F, 796F (Flip top models) 4,164.00 (78 wide, 971/4 long, 37.5 high, 49 cargo area) 1.0-4 Full Height model (F40J) 4,253.00 108 Bodies to fit 60 CA Single Wheel Chassis 1.0-5 Knapheide, 5108, 6108, 7108, Standard Models 4,008.00 (78 wide, 109 ¼ long, 40 high, 49 cargo area) 1.0-6 Low profile model (LPJ) 37.5 3,958.00 1.0-7 Knapheide 5108F, 6108F, 7108F (Flip top models) 4,751.00 (78 wide, 1091/4 long, 37.5 high, 49 cargo area) 108 Bodies to fit 60 CA Dual Wheel Chassis 1.0-8 Knapheide, 5108D, 6108D, 7108D, Standard Models 4,303.00 (89 wide, 109 ¼ long, 40 high, 54 cargo area) 1.0-9 Knapheide, 5108D54, 6108D54, 7108D54, Standard Models 4,503.00 (94 wide, 109 ¼ long, 40 high, 54 cargo area) 1.0-10 Low profile model (LPJ) 37.5 4,447.00 1.0-11 Knapheide 5108D54FJ, 6108D54FJ, 7108D54FJ (Flip top models) 5,275.00 (94 wide, 1091/4 long, 37.5 high, 54 cargo area) 132 Bodies to fit 84 CA Dual Wheel Chassis 1.0-12 Knapheide, 5132D54J, 6132D54J, 7132D54J, Standard Models 6,128.00 (94 wide, 133 ¼ long, 40 high, 54 cargo area) Low profile model (LPJ) 37.5 1.0-13 Knapheide 5132D54F, 6132D54F, 7132D54F (Flip top models) 7,007.00 (94 wide, 133 ¼ long, 37.5 high, 54 cargo area) 1.0-14 157 Bodies to fit 108 CA Dual Wheel Chassis Knapheide, 6157D54, Standard Models 8,359.00 (94 wide, 158 ¼ long, 40 high, 54 cargo area) 1.0-15 Chassis Specific Mounting Kit (includes light adaptors for current Model Years) 195.00 Light Kits, Fuel Fill, and Bumper Options 1.20 LED Surface Mount lights (new style) S/T/T and B/U light kit with strobe feature 210.00 1.21 LED S/M lights (new style) S/T/T & B/U light kit with strobe (+80" wide Body) 290.00 1.22 Light harness adaptors other than Ford and LED Flashers refer to Knap OF Non Contact Item 1.23 Strobe light hook up kit wired to OEM upfitter switch 125.00 123A Ecco Front Strobe Kit With wiring kit, Installed 350.00 1.24 Aluminum Fuel Fill Cup and pre punched hole, for fuel or DEF Location 83.00

1.25 GM Fuel Fill Kit required for GM Chassis 56 CA with box removal 320.00 1.26 GM Fuel Fill Kit required for GM Chassis 60-84 CA 100.00 1.27 Ford Fuel Fill Kit 40/56" CA DRW Chassis 80.00 1.28 TFI Ford Fuel Fill Kit for Ford 56" CA Chassis 335.00 128A Fill neck KIT and fuel Cap (required on chassis that do not have Fuel Cap) 250.00 1.29 78 Standard Treadplate or Galvi-grip Step Bumper 280.00 1.30 78 Standard Treadplate or Galvi-grip with PHR 285.00 1.31 78 Standard Treadplate or Galvi-grip with BMR 359.00 1.32 94 Standard Treadplate or Galvi-grip Step Bumper 339.00 1.33 94 Standard Treadplate or Galvi-grip with PHR 354.00 1.34 94 Standard Treadplate or Galvi-grip with BMR 426.00 1.35 94 Standard Grip Strut Bumper with PHR 685.00 Paint options for Knapheide Standard Service Bodies 1.36 Knapheide "blended" White OEM Paint J-Series 96" Bodies 725.00 1.37 Knapheide "blended" White OEM Paint FJ-Series 96" Bodies 815.00 1.38 Knapheide "blended" White OEM Paint J-Series 108" Bodies 785.00 1.39 Knapheide "blended" White OEM Paint FJ-Series 108" Bodies 875.00 1.40 Knapheide "blended" White OEM Paint J-Series 132" Bodies 940.00 1.41 Knapheide "blended" White OEM Paint FJ-Series 132" Bodies 1,065.00 1.42 Knapheide "blended" White OEM Paint J-Series 157" Bodies 1,300.00 1.43 Knap Liner or paint Bumper add 150.00 1.43A Knapheide 1848 package (in addition to factory paint charge) includes power locks, LED Compartment lights, Sortimo boxx package in Left Horizontal, Aluminum Rock Guards, and Aluminum tailgate trim 696 series Add 2,290.00 6108 Series Add 2,450.00 6132 Series Add 2,495.00 1.43B Knapheide Pioneer Package (In addition to Factory paint Charge) includes Masterlock, Aluminum Trim package, Aluminum Rock guards 696 Series Add 1,080.00 6108 Series Add 1,350.00 Berts painting 1.44 Paint One Standard Color White X96J service bodies 1,150.00 1.45 Paint One Standard Color White X108J Service Bodies 1,150.00 1.46 Paint One Standard Color White X132D54J Service Bodies 1,395.00 1.47 Paint One Standard color White 6157D54 Service Bodies 1,530.00 1.48 Adder for color other than white 295.00 1.49 Adder for BC/CC 650.00 1.50 Paint Cargo Area Black 365.00 Line-x cargo Liner (includes bumper) in Cargo Area 1.51 96" Bodies 750.00 1.52 108" Bodies 775.00 1.53 132" Bodies 850.00 1.54 157" Bodies 995.00 1.55 Basic Installation of all Knapheide Service Bodies: (Includes installation of body, light kit, bumper and fuel fill) 735.00 1.55-1 Installation of Knapheide Option fit items shipped loose from factory 100.00 P/hr (See Section 11.1 for Knapheide Option fit pricing)

1.55-2 Installation of OEM Supplied Backup Camera 100.00 1.55-3 Provided and install Standard Rostra OEM Compatable Camera 250.00 1.55-4 Provide and install HD Rostra OEM Compatable Camera 310.00 Common Options For Knapheide utility bodies (some options may be required) 1.56 Full Height Aluminum Rock Guards on front of body 150.00 1.57 Corner mounted Crane reinforcement up to #4000 cap crane 997.00 1.58 Torsion Box Floor 96" & 108" Bodies (includes Mounting Kit) 815.00 1.59 Torsion Box Floor 132" Bodies (Includes Mounting Kit) 1,124.00 1.60 Torsion Box Floor 157" Bodies (IncLudes Mounting Kit) 1,377.00 1.61 Double Overlapped Front Vertical Doors ILO standard 130.00 1.62 Double Overlapped Door on Horizontal ILO Standard 110.00 1.63 Tread Bright Aluminum Trim Package (Compartment Tops) 96 Series Bodies 479.00 1.64 Tread Bright Aluminum Trim Package (Compartment Tops) 108 Series Bodies 644.00 1.65 Tread Bright Aluminum Trim Package (Compartment Tops) 132 Series Bodies 743.00 1.66 Tread Bright Aluminum Trim Package (Compartment Tops) 157 Series Bodies 910.00 1.67 Standard Bottle gas retainer, installed 353.00 1.68 Drop well bottle gas retainer, installed 366.00 1.69 LED Compartment Lights (1-strip) per Compartment 95.00 1.70 Transverse Compartment open to Curbside Front Vertical Compartment 845.00 1.71 Transverse Compartment open to Both Front Verticals Compartments 925.00 1.72 Interior Rope lights per compartment (Continuious) 125.00 1.73 LED Gromet mounted Strobe Lights in Rear of Body 295.00 1.74 Mechanics Vice Bracket (standard) 135.00 1.75 Removable Mechanics Vice Bracket 210.00 175A Wilton Truck Vise, Installed 275.00 1.76 97 db back/up alarm installed 75.00 1.77 Variable db Back up Alarm, installed 120.00 1.78 White Noise back up alarm, installed 170.00 1.79 Star 240CFD Double Flash Strobe on Stand 220.00 1.79A Hella LED Mini-Light bar, Installed on Pedistal 460.00 1.80 Samlex SSW-200012A Inverter 540.00 1.80A Samlex PST-200012 HD Inverter 895.00 180.B Remote kit for HD Samlex Inverter 75.00 1.81 400 amp fuse, cabling and installation of Inverter 585.00 1.82 New Take off Pick-up box trade allowance (600.00) 1.83 Rear Window/cab Guard 495.00 1.84 Relocate OEM Backup camera 485.00 Hitch Options 1.85 Class IV Receiver Hitch 300.00 1.86 Buyers Class V Reciever Hitch Rated at 16000LB 2 " Reciver Tube 320.00 1.87 Buyers Class V Reciever Hitch Rated at 16000LB 2 1/2" Reciver Tube 330.00 1.88 Reese Titan Class 5 14000 LB 2 1/2" Reciever Hitch 635.00 1.89 Reese Class V Ball Mount with Pin 40.00 1.90 Reese Class V Pintle Mount with pull pin 130.00 1.91 Combination Pinlte/Ball (specify ball size) 85.00 1.92 PH20 Pintle hook 80.00 1.93 Deluxe TEK Prodigy Electric brake Control, Installed 250.00 1.94 6-way or 7-way trailer plug, installed 60.00 1.95 Swift Hitch Wireless Cameras Model SHO1 (qty 1-9) each 230.00 1.96 Swift Hitch Wireless Cameras Model SHO1 (qty 10-20) each 220.00 1.97 Swift Hitch Wireless Cameras Model SHO1 (qty 21+) each 210.00 1.98 Swift Hitch Wireless Cameras Model SHO2 (qty 1-9) each 264.00 1.99 Swift Hitch Wireless Cameras Model SHO2 (qty 10-19) each 259.00 1.100 Swift Hitch Wireless Cameras Model SHO2 (qty 20+) each 249.00 Page 5 of 5

Canopy Roofs (straight) For 96 to 132 Service Bodies, ALSO SEE Knapheide CC-KUV Bodies Section for bodies with tapered canopy's 1.101 55" Standard Canopy Roof for SRW 56" CA Body 3,230.00 1.102 55" Standard Canopy Roof for DRW 56" CA Body 3,460.00 1.103 65" Standard Canopy Roof for DRW 56" CA Body 4,115.00 1.104 73 Standard Canopy Roof for 108 Body installed at Factory 4,455.00 1.105 72 Standard Canopy Roof for 132 Body installed at Factory 5,460.00 1.106 Additional paint charge for Canopy Roofs 900.00 1.107 Finish paint inside of Cargo Area/canopy ILO of light gray finish 1,250.00 Telescopic Sliding Roofs 1.108 TSR to fit 96 SW Body 1,275.00 1.109 TSR to fit 96 DW Body 1,395.00 1.110 TSR to fit 108 SW Body 1,345.00 1.111 TSR to fit 108 DW Body 1,475.00 1.112 TSR to fit 132 DW Body 2,325.00 1.113 Painting Adder for TSR 96 & 108 525.00 1.114 Painting Adder for TSR132 575.00 Cost per mile for pick-up or Delivery to or from Moorhead, MN 2.25 (Maximum charge per unit for pick-up/delivery one way 425.00) Buyer sguide for pricing Service Body: Chassis CA SW DW Make and Model of Chassis: Base Body Light kit Bumper Painting Installation BASIC PACKAGE TOBASIC PACKAGE TOTAL Additional Options: Delivery (max 425.00 one way) Total Package Body and Equipment By: Bert s Truck Equipment Inc. Jim McLaughlin, Commercial Fleet Sales 3804 Hwy 75 North Moorhead, MN 56560 800-232-3787, 218-233-8681 Fax 218-233-9548 Email: jimmc@bertsonline.com Web Site: www.bertsonline.com

STATE OF MINNESOTA PRICING 11-30-17 Bert's Truck Equipment of Moorhead 1.0 Knapheide Cab Chassis KUV Utility/Service Bodies to fit 56, 60, 84 & 108 CA Chassis s Standard Features: Body Shell 14 gauge two-sided A40 galvanneal steel. Compartment top and back are one piece seamless design. All doors, door openings, drip rails, and other exposed steel edges to be hemmed for strength, safety and resistance to corrosion. Floor 12 gauge treadplate with 1 3/8 return flange on each side. Side compartment back panel overlaps and interlocks with floor flange, providing support for weight of side compartment. Understructure 50,000 yield 11 gauge high strength steel cross sills. Page 1 of 7 Doors 20 gauge two-sided A40 galvanneal steel double panel doors with hat section reinforcements. Hinges Corrosion resistant all stainless steel continuous hinges provide full length support for the doors and pry-proof security with a built-in weather shield. Hinge to be spot welded to the door frame supported with a five year warranty. Rotary Latches Automotive rotary latches riveted to door with noncorrosive aluminum rivets incorporation stainless mandrels. Rotary latch is slamlatchable. Latching cam to be elongated to allow the latch to move vertically relative to the lockstrike to prevent torsional damage. Door Strikers Adjustable striker affixed to door frame with screws. ( Door Seals Automotive bulb type neoprene door seals to be installed by the manufacturer of the body on all door frames. Door Retainer Double spring over center door retainers on all vertical doors, retains doors in positive open or closed position. Shelving 18 gauge bright spangled galvanized shelves with hemmed dividers on 4 centers. Minimum 250 lbs. capacity rated. Exterior Prime Paint Body is completely immersed in electrodeposition gray epoxy prime paint featuring a zinc phosphate pre-coat and seal for additional corrosion protection. Prime paint is oven cured to provide a hard durable finish. Interior Paint Interior painted mid-gloss, mar resistant, light gray finish. Undercoating Body is completely undercoated by the manufacturer of the body using minimum five (5) mils of water base acrylic. Warranty The following items to be covered by minimum six (6) year limited warranty to first owner/user of record. No Rust-Thru Guarantee Page 2 of 7

Continuous Door Hinge Guaranteed not to fail to operate or come off product. Latches and Lock Cylinders Guarantee against failure. Shelves Guaranteed not to fail in bending under maximum 250lb. rated load. Other Standard Features KnapTight Double panel rear doors with rear window guards Two Conduit Chutes to transport copper pipe, PVC, and conduit Masterlock system, standard (Knaplock keyless entry optional) Spacious cargo area for transporting large tools and oversized items Two interior Dome Lights with light switch inside cargo area Grab handle at rear Many other standard Features Base Price includes, Standard Body as provided by Knapheide with Standard Shelving Package. All prices are FOB Moorhead and are Load Out, Prime painted 96 Bodies to fit Single Wheel 56 CA Chassis 1.0-1 Knapheide KC96U1478 KUV Service Body Contract Price (78 wide, 97 ¼ long, 62 high, 49 cargo area, 45.1" Interior Hieght) 6,340.00 1.0-2 Knapheide KC96L1478 KUV Service Body (78 wide, 97 ¼ long, 68 high, 49 cargo area, 51.1" Interior Hieght) 6,628.00 1.0-3 Knapheide KC96M1478 KUV Service Body (78 wide, 97 ¼ long, 78 high, 49 cargo area, 61.1" Interior Hieght) 6,821.00 96 Bodies to fit Dual Wheel 56 CA Chassis 1.0-4 Knapheide KC96U2094 KUV Service Body (94 wide, 97 ¼ long, 62 high, 54 cargo area, 45.1" Interior Hieght) 7,210.00 1.0-5 Knapheide KC96L2094 KUV Service Body (94 wide, 97 ¼ long, 68 high, 54 cargo area, 51.1" Interior Hieght) 7,491.00 1.0-6 Knapheide KC96M2094 KUV Service Body (94 wide, 97¼ long, 78 high, 54 cargo area, 61.1" Interior Hieght) 7,699.00 1.0-7 Knapheide KC96H2094 KUV Service Body (94 wide, 97¼ long, 90 high, 54 cargo area, 73.1" Interior Hieght) 7,926.00 108 Bodies to fit 60 CA Single Wheel Chassis 1.0-8 Knapheide KC108U1478 KUV Service Body (78 wide, 107 ¼ long, 62 high, 49 cargo area, 45.1" Interior Hieght) 6,982.00 1.0-9 Knapheide KC108L1478 KUV Service Body (78 wide, 107¼ long, 68 high, 49 cargo area, 51.1" Interior Hieght) 7,273.00 1.0-10 Knapheide KC108M1478 KUV Service Body (78 wide, 107¼ long, 78 high, 49 cargo area, 61.1" Interior Hieght) 7,599.00

108 Bodies to fit 60 CA Dual Wheel Chassis 1.0-11 Knapheide KC108L2094 KUV Service Body (94 wide, 107 ¼ long, 68 high, 54 cargo area, 51.1" Interior Hieght) 1.0-12 Knapheide KC108M2094 KUV Service Body (94 wide, 107¼ long, 78 high, 54 cargo area, 61.1" Interior Hieght) 1.0-13 Knapheide KC108H2094 KUV Service Body (94 wide, 107¼ long, 90 high, 54 cargo area, 73.1" Interior Hieght) 1.0-14 89" wide Body ILO 94" wide Body Deduct 7,747.00 8,030.00 8,361.00 132 Bodies to fit 84 CA Dual Wheel Chassis 1.0-15 Knapheide KC132L2094 KUV Service Body (94 wide, 133 ¼ long, 68 high, 54 cargo area, 51.1" Interior Hieght) 8,634.00 1.0-16 Knapheide KC132M2094 KUV Service Body (94 wide, 133¼ long, 78 high, 54 cargo area, 61.1" Interior Hieght) 8,985.00 1.0-17 Knapheide KC132H2094 KUV Service Body (94 wide, 133¼ long, 90 high, 54 cargo area, 73.1" Interior Hieght) 9,373.00 1.0-18 89" wide Body ILO 94" wide Body Deduct (94 wide, 158 ¼ long, 40 high, 54 cargo area) (75.00) 157 Bodies to fit 108 CA Dual Wheel Chassis 1.0-22 Knapheide KC157H2094 KUV Service Body (94 wide, 157¼ long, 90 high, 54 cargo area, 73.1" Interior Hieght) 13,100.00 169 Bodies to fit 120 CA Dual Wheel Chassis 1.0-26 Knapheide KC169H2094 KUV Service Body (94 wide, 169¼ long, 90 high, 54 cargo area, 73.1" Interior Hieght) 13,275.00 1.0-27 Chassis Specific Mounting Kit (includes light adaptors for current Model Years) 195.00 Light Kits Fuel Fill, and Bumper Options Light Kits Fuel Fill, and Bumper Options 1.20 LED Surface Mount lights (new style) S/T/T and B/U light kit with strobe feature 250.00 1.21 LED S/M lights (new style) S/T/T & B/U light kit with strobe (+80" wide Body) 340.00 1.22 Light harness adaptors other than Ford and LED Flashers refer to Knap OF NCI 1.23 Strobe light hook up kit wired to OEM upfitter switch 125.00 123A Ecco Front Strobe Kit With wiring kit, Installed 350.00 1.24 Aluminum Fuel Fill Cup and pre punched hole, for fuel or DEF Location 80.00 1.25 GM Fuel Fill Kit required for GM Chassis 56 CA with box removal 310.00 1.26 GM Fuel Fill Kit required for GM Chassis 60-84 CA 95.00 1.27 Ford Fuel Fill Kit 40/56" CA DRW Chassis 80.00 1.28 TFI Ford Fuel Fill Kit for Ford 56" CA Chassis 325.00 128A Fill neck KIT and fuel Cap (required on chassis that do not have Fuel Cap) 250.00 1.29 78 Standard Treadplate or Galvi-grip Step Bumper 280.00 1.30 78 Standard Treadplate or Galvi-grip with PHR 285.00 1.31 78 Standard Treadplate or Galvi-grip with BMR 359.00 1.32 94 Standard Treadplate or Galvi-grip Step Bumper 339.00 1.33 94 Standard Treadplate or Galvi-grip with PHR 354.00 1.34 94 Standard Treadplate or Galvi-grip with BMR 426.00

1.35 94 Standard Grip Strut Bumper with PHR 685.00 Paint options for Knapheide Standard Service Bodies 1.36 Knapheide "blended" White OEM Paint KC-Series 96" Bodies 1,350.00 1.37 Knapheide "blended" White OEM Paint KC-Series 108" Bodies 1,495.00 1.38 Knapheide "blended" White OEM Paint KC-Series 132" Bodies 1,695.00 1.39 Knapheide "blended" White OEM Paint KC-Series 157" Bodies 1,995.00 1.40 Knap Liner or paint Bumper add 125.00 Page 5 of 7 Berts Paint Options 1.41 Paint One Standard Color White X96J service bodies 1,675.00 1.42 Paint One Standard Color White X108J Service Bodies 1,795.00 1.43 Paint One Standard Color White X132D54J Service Bodies 1,995.00 1.44 Paint One Standard color White 6157D54 Service Bodies 2,395.00 1.45 Adder for color other than white 450.00 1.46 Adder for BC/CC 725.00 1.47 Finish paint inside of Cargo Area/canopy ILO of light gray finish 1,095.00 Line-x cargo Liner (includes bumper) in Cargo Area 1.48 96" Bodies 775.00 1.49 108" Bodies 820.00 1.50 132" Bodies 895.00 1.51 157" Bodies 995.00 1.52 Basic Installation of all Knapheide Service Bodies: 835.00 (Includes installation of body, light kit, bumper and fuel fill) 1.53 Installation of Knapheide Option fit items shipped loose from factory 100.00 P/Hr American Eagle Drawers 1.54 3" Drawer up to 30" wide for standard service body 280.00 1.55 5" Drawer up to 30" wide for standard service body 280.00 1.56 7" Drawer up to 30" wide for standard service body 280.00 1.57 Top Tray up to 30" wide Included 1.58 Riser up to 30" wide Included 1.59 3" Drawer up to 30-50" wide for standard service body 310.00 1.60 5" Drawer up to 30-50" wide for standard service body 310.00 1.61 7" Drawer up to 30-50" wide for standard service body 310.00 1.62 Top Tray up to 30" wide Included 1.63 Riser up to 30" wide Included Common Options For Knapheide utility bodies (some options may be required) 1.64 Full Height Aluminum Rock Guards on front of body 150.00 1.65 Torsion Box Floor 96" & 108" Bodies (includes Mounting Kit) 815.00 1.66 Torsion Box Floor 132" Bodies (Includes Mounting Kit) 1,124.00 1.67 Torsion Box Floor 157" Bodies (IncLudes Mounting Kit) 1,377.00 1.68 Double Overlapped Front Vertical Doors ILO standard 130.00 1.69 Double Overlapped Door on Horizontal ILO Standard 110.00 1.70 Standard Bottle gas retainer, installed 353.00

1.71 Drop well bottle gas retainer, installed 366.00 1.72 LED Compartment Lights (1-strip) per Compartment 95.00 1.73 Transverse Compartment open to Curbside Front Vertical Compartment 825.00 Page 6 of 7 1.74 Transverse Compartment open to Both Front Verticals Compartments 925.00 1.75 Interior Rope lights per compartment (Continuious) 125.00 1.76 LED Gromet mounted Strobe Lights in Rear of Body 295.00 1.77 Mechanics Vice Bracket (standard) 135.00 1.78 Removable Mechanics Vice Bracket 210.00 1.79 97 db back/up alarm installed 75.00 1.80 Variable db Back up Alarm, installed 120.00 1.81 White Noise back up alarm, installed 170.00 1.82 Star 240CFD Double Flash Strobe on Stand 210.00 1.83 LED Mini-Light bar, Installed on Pedistal 460.00 1.84 New Take off Pick-up box trade allowance (600.00) 1.87 Relocate OEM Backup camera 485.00 See Price Schedule 11.1 for other Knapheide Option Fit Pricing Hitch Options 1.89 Class IV Receiver Hitch 300.00 1.90 Buyers Class V Reciever Hitch Rated at 16000LB 2 " Reciver Tube 320.00 1.91 Buyers Class V Reciever Hitch Rated at 16000LB 2 1/2" Reciver Tube 330.00 1.92 Reese Titan Class 5 14000 LB 2 1/2" Reciever Hitch 635.00 1.93 Reese Class V Ball Mount with Pin 40.00 1.94 Reese Class V Pintle Mount with pull pin 130.00 1.95 Combination Pinlte/Ball (specify ball size) 85.00 1.96 PH20 Pintle hook 80.00 1.97 Deluxe TEK Prodigy Electric brake Control, Installed 250.00 1.98 6-way or 7-way trailer plug, installed 60.00 1.99 Swift Hitch Wireless Cameras Model SHO1 (qty 1-9) each 230.00 1.100 Swift Hitch Wireless Cameras Model SHO1 (qty 10-20) each 220.00 1.101 Swift Hitch Wireless Cameras Model SHO1 (qty 21+) each 210.00 1.102 Swift Hitch Wireless Cameras Model SHO2 (qty 1-9) each 264.00 1.103 Swift Hitch Wireless Cameras Model SHO2 (qty 10-19) each 259.00 1.104 Swift Hitch Wireless Cameras Model SHO2 (qty 20+) each 249.00 1.105 Ag Cam Wired backup camera 7" Monitor with one camera, 360.00 1.105A Ag Cam Wired backup camera 3.5" Monitor with one camera, 215.00 1.105B Ag Cam Wired backup camera 7" Monitor Qaud Screen, with one camera, 560.00 1.105C Ag cam additional camera, 65' cable 150.00 1.106 Installation of Ag cam camera, system one camera 200.00 1.106A Adder for Install of additional camera, each 100.00 1.105D Rostra OEM standard Compatable Camera,with chassis adaptor for GM Chassis, Installed (Chassis must be ordered with 7" monitor and factory programmed for backup camera) 275.00 Cost per mile for pick-up or Delivery to or from Moorhead, MN 2.25 (Maximum charge per unit for pick-up/delivery one way 425.00) Buyer sguide for pricing Service Body: Chassis CA SW DW Make and Model of Chassis: Page 7 of 7 Base Body Light kit

Bumper Painting Installation BASIC PACKAGE TOTAL Additional Options: Delivery (max 425.00 one way) Total Package Body and Equipment By: Bert s Truck Equipment Inc. Jim McLaughlin, Commercial Fleet Sales 3804 Hwy 75 North Moorhead, MN 56560 800-232-3787, 218-233-8681 Fax 218-233-9548 Email: jimmc@bertsonline.com Web Site: www.bertsonline.com

STATE OF MINNESOTA PRICING 11-30-17 Bert's Truck Equipment of Moorhead Knapheide Crane Bodies For Crane Applications #4000lb and Greater Standard Features: Body Shell 14 GA two-sided A40 galvanneal steel compartment wall panels, fenderskirts and drip rails with 12GA two-sided A40 galvanneal steel backs, bottoms and bulkhead. 12 GA treadplate top and backs full length welded to the compartment structure and floor. Floor 1/8 thick treadplate floor with 1 3/8 return flange on each side. Side compartment back panel overlapping and interlocking with floor flange, providing support for weight of side compartment. Full length welded. Understructure Torsion box design with internal longitudinal supports and full width tubular cross sills. Shear plates and mounting incorporated into rear understructure. Crane Pedestal ¼ wall box construction with ¾ steel mounting plate predrilled for crane mounting bolts. Crane pedestal isolated from side compartments. Rated for a maximum of 30,000, 38,000 for 60,000 ft. lbs. thru 360 degrees rotation depending on model selected. Tailgate 14 gauge two-sided A40 galvanneal steel double panel construction 12 high slammable style installed on body. Doors 14GA two-sided A40 galvanneal steel outer door panel with 20GA two-sided A40 galvanneal steel liner and hat section reinforcement. Overlap style doors on front vertical and horizontal compartments. Compartments Seam welded inside and outside of compartments. Hinges Corrosion resistant all stainless steel continuous hinges to provide full length support for the doors and pry-proof security with a built-in weather shield. Hinge are spot welded to the door frame supported with a five year warranty. Latches Stainless steel three point twist latches riveted to door with non-corrosive stainless steel rivets Door Seals Automotive bulb type neoprene door seals isinstalled by the manufacturer of the body on all door frames. Door Retainer Double spring over center door retainers on all vertical doors, retains doors in positive open or closed position. Shelving (optional) 18 gauge bright spangled galvanized shelves with hemmed dividers on 4 centers. Minimum 250 lbs. capacity rated. Shelves can be positioned vertically on 2 centers. Page 1 of 4 Exterior Prime Paint Body is completely immersed in electrodeposition gray epoxy prime paint featuring a zinc phosphate precoat and seal for additional corrosion protection. Prime paint is oven cured to provide a hard durable finish. Interior Paint Page 2 of 4

Interior paint is mid-gloss, mar resistant, light gray finish. Undercoating Body is completely undercoated by the manufacturer of the body. Installation Body is supplied a recommended installation process along with detailed installation instructions that conforms to all applicable Federal Motor Vehicle Safety Standards. Further, manufacturer of the body to supply owner manual describing proper care and maintenance of the body for user. Warranty The following items to be covered by minimum six (6) years limited warranty to first owner/user of record. No Rust-Thru Guarantee Continuous Door Hinge Guaranteed not to fail to operate or come off product. Latches and Lock Cylinders Guarantee against failure. Shelves Guaranteed not to fail in bending under maximum 250lb. rated load. Lighting Lighting to meet all applicable FMVSS standards. Light harness are encased in plastic loom, and all wires colored for ease in troubleshooting. Wire harness have connectors compatible with applicable Ford, GM and Dodge chassis without splicing. Stop, tail, turn, backup and side maker lights recessed in aluminum light boxes at rear of body. Body end panels prepunched for wires and box mounting. All exterior S/T/T lights are included in base price Lighting Wire Retention Wires must be retained by mechanical fastening system. Base Price includes Standard Body as provided by Knapheide. Shelving packages are not included. All prices are FOB Moorhead and are Load Out, Prime painted 108 Bodies to fit 60 CA Chassis 1.0-1 Knapheide, 6108DL-38, Standard Crane Body 10,225.00 (94 x108 Long, 44 compartment height) 1.0-2 Knapheide, 6108DLR-38, Standard Crane Body 10,830.00 (94 x108 Long, 44 compartment height, 60 Raised Front Vertical) 132 Bodies to fit 84 CA Chassis 1.0-3 Knapheide, 6132DL-30, Standard Crane Body 8,635.00 (94 132 Long, 44 compartment Hieght) 1.0-4 Knapheide, 6132DLR-30, Standard Crane Body 9,235.00 1.0-5 Knapheide, 6132D-38L, Standard Crane Body 11,515.00 (94 132 Long, 44 compartment Hieght) Page 3 of 4 1.0-6 Knapheide, 6132DLR-38L, Standard Crane Body 12,115.00 (94 132 Long, 44 compartment Hieght, 60" Raised Front Vertical) 1.0-7 Knapheide, 6132DLHR-60J, Standard Crane Body 14,335.00 (94 x132 Long, 44 compartment height, 60 Raised Front Vertical) 1.07A Knapheide, 6132DLR-44, Standard Crane Body 12,245.00 (94 132 Long, 44 compartment Hieght, 60" Raised Front Vertical) Light kits are shipped loose and included in base body price

Mounting Kit Bumpers and Other Commons Standard Options 1.20 Mounting kit for F350/450/555 and GM 3500-5500 38J Series Body 325.00 1.21 Mounting kit for F350/450/555 and GM 3500-5500 30J Series Body 195.00 1.22 DL Series Rear Crane Body Bumper Installed at factory (w/outrigger tubes, vice mount, receiver hitch & through compartmen 1,868.00 1.23 DLH Series Rear Crane Body Bumper Installed at factory (w/outrigger tubes, vice mount, receiver hitch & through compartmen 2,225.00 1.24 DLH Series Rear Crane Body Bumper Installed at factory (body with Master Lock System 2,575.00 (w/outrigger tubes, vice mount, receiver hitch & through compartment) 1.25 Aluminum Fuel Fill Cup and pre punched hole 80.00 Paint options for Knapheide Standard Service Bodies 1.27 Paint One Standard Color 6108DL Crane Bodies 1,625.00 1.28 Paint One Standard Color 6132DL Crane Bodies 1,795.00 1.29 Adder for Red - Yellow 400.00 1.30 Adder for BC/CC 750.00 Basic Installation of all Knapheide Crane Bodies: 1.31 (Includes installation of body, light kit, bumper and fuel fill) 1,435.00 Cost per mile for pick-up or Delivery to or from Moorhead, MN 2.25 (Maximum charge per unit for pick-up/delivery one way 450.00) Shelving and other Options Knapheide Standard Package A 1.32 Installed in 6108DL-38J 945.00 1.33 Installed in 6108DLR-38J 1,175.00 1.34 Installed in 6132DL-38J 1,175.00 1.35 Installed in 6132DLR-38J 0r 6132LHR-60J 1,395.00 Knapheide Standard Package B 1.36 Installed in 6108DL-38J 1,045.00 1.37 Installed in 6108DLR-38J 1,275.00 1.38 Installed in 6132DL-38J 1,275.00 1.39 Installed in 6132DLR-38J 0r 6132LHR-60J 1,495.00 Knapheide Standard Package C 1.4 Installed in 6108DL-38J 2,230.00 1.41 Installed in 6108DLR-38J 2,460.00 1.42 Installed in 6132DL-38J 2,460.00 1.43 Installed in 6132DLR-38J 0r 6132LHR-60J 2,695.00 1.44 Crane Body A/E Drawer Stack(1-7", 3-5" & 3-3" Drawers) 1,750.00 See Price Schedule 11.1 for other Knapheide Option Fit Pricing Page 4 of 4 Buyer sguide for pricing Crane Body: Chassis CA Make and Model of Chassis: Base Body Bumper Painting Installation BASIC PACKAGE TOTAL Shelving & Options:

Delivery (max 450.00 one way) Total Package Body and Equipment By: Bert s Truck Equipment Inc. Jim McLaughlin, Commercial Fleet Sales 3804 Hwy 75 North Moorhead, MN 56560 800-232-3787, 218-233-8681 Fax 218-233-9548 Email: jimmc@bertsonline.com Web Site: www.bertsonline.com

Service Bodies Contract end Date 09-30-18 Vendor Name: Bert's Truck Equipment, Inc Contact Person: Jim McLaughlin Street Address: 3804 Highway 75 North P.O. Box: 336 City, State, Zip Moorhead, MN 56561-0336 Phone #: 218-233-8681 Toll Free #: 800-232-3787 Fax #: 218-233-9548 Email Address: jimmc@bertsonline.com Website: www.bertsonline.com Version of Excel used: 2013 Furnish separate price quote for: BODY COMPONENTS AND ATTACHMENTS FOR 6,000 1.0 UTILITY /SERVICE BODY Make Fiberline Fibergalss Utility Bodies Warranty 5 Year Limited Warranty Date & I.D. of Price List 11/30/2017 Discount to be applied to Price List* (see note below) 0.00% Installation of Utility/Service Body as per MnDOT spec 1.0 See Attached Price Schedule Price of FMVSS 108 lighting package See Attached Price Schedule Price of ICC bumper under ride protection See Attached Price Schedule Installation of ICC bumper under the protection See Attached Price Schedule Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Moorhead, MN 56560 Price per loaded mile for delivery 2.25 Delivery Time Frame in calendar days ARO 30-120 Shop Rate per Hour Shop Rate for Mechanical work 100.00 Body Shop Rate 100.00 *Note: The "Discount to be Applied to Price List" must be a

STATE OF MINNESOTA PRICING 11-30-17 Bert's Truck Equipment of Moorhead FIBER LINE SERVICE BODY STANDARD EQUIPMENT STANDARD BODY EQUIPMENT INCLUDES: 1/8 Steel treadplate floor and bulkhead, primed and painted gloss black. Gelcoat finish to match standard chassis white. Molded fiberglass side packs. All interior fiberglass gelcoated white. Stainless steel paddle latches, all keyed alike. Fully adjustable door strikers with safety catch. Fiber Line designed automotive style weather-strip. Aluminum treadbrite front rock guards. Stainless steel rear wheel well rock guards. Stainless steel HD hinges. All stainless steel bolts and self-locking nuts. Extruded aluminum drip rails above all side doors. Fiberglass bulkhead between compartments. Flush shock mounted exterior lights to meet FMVSS#108. Lighted license plate bracket. Loomed one piece wiring harness with molded plug. Floor drains in front and rear vertical compartments. Dual fuel recess molded into streetside side pack. 8 Aluminum drop-down tailgate (40" high bodies only). Vents in each side pack. Cable door stops on all side doors. Non skid on tops of side packs. Contract Price 1.0-1 96 Standard body (Single Rear Wheel 56" CA) Body Length - 96" Body Width - 79" Body Height - 40" Compartment Depth - 15" 1.0-2 96 Standard body (Dual Rear Wheel 56" CA) Body Length - 96" Body Width - 94" Body Height - 40" Compartment Depth - 20" 1.0-3 96" High side body (Single Rear Wheel 56" CA) 3 point "D" ring latches on all side doors Body Length - 96" Body Width - 79" Body Height - Up to 64" Tall Compartment Depth - 15" Price 6,368.00 Price 7,143.00 Price 8,455.00

1.0-4 96" High Side body (Dual Rear Wheel 56" CA) 3 point "D" ring latches on all side doors Body Length - 96" Body Width - 94" Body Height - Up to 64" Compartment Depth - 20" 1.0-5 96 Standard body (Single Rear Wheel 56" CA) Body Length - 96" Body Width - 79" Body Height - 35" Compartment Depth - 15" 1.0-6 96 Standard body (Dual Rear Wheel 56" CA) Body Length - 96" Body Width - 94" Body Height - 35" Compartment Depth - 20" 1.0-7 108" Standard body (Dual Rear Wheel 60" CA) Body length -108" Body Width - 94" Body Height - 40" Compartment Depth - 18" 1.0-8 108" Standard body (Single Rear Wheel 60" CA) Body length - 108" Body Width - 79" Body Height - 40" Compartment Depth - 15" 1.0-9 108" Line body (Dual Rear Wheel 60" CA) Body Length - 108" Body Width - 94" Body Height - 48" Compartment Depth - 18" 1.0-10 108" Line body (Single Rear Wheel 60" CA) Body length - 108" Body Width - 79" Body Height - 48" Compartment Depth - 15" 1.0-11 132" Standard body (Dual Rear Wheel 84" CA) Body Length - 132" Body Width - 94" Body Height- 40" Compartment Depth - 18" Price 8,759.00 Price 6,368.00 Price 7,143.00 Price 6,905.00 Price 6,905.00 Price 9,488.00 Price 9,488.00 Price 8,133.00

1.0-12 132" Line body (Dual RearWheel 84" CA) Body Length - 132" Body Width - 94" Body Height - 48" Compartment Depth - 18" Price 12,462.00 COMPARTMENT OPTIONS: 1.20 Standard shelving package for all bodies up to 108" length: (2) adjustable aluminum open shelves in each front vertical compartment: (1) fixed aluminum shelf with removable dividers in streetside horizontal compartment (1) adjustable aluminum open shelf each rear compartment 1.21 Standard shelving package for all 132" length bodies: {2} adjustable aluminum open shelves in each front vertical compartments (2) adjustable aluminum open shelves in 2nd vertical compartment (1) Fixed divider tray with removable dividers in streetside horizontal compartment (1) adjustable aluminum open shelf in each rear compartment COMPARTMENT OPTIONS: Vertical Compartment Shelving: 1,004.00 1,517.00 1.22 (1) Adjustable aluminum divider tray with removable dividers 218.00 1.23 (2) Adjustable aluminum divider tray with removable dividers 385.00 (3) Adjustable aluminum divider tray with removable dividers 550.00 Aluminum pull-out drawer on slides: 2" deep with dividers on 2" centers, 1.24 Mounted on full extension Grant sides must include price of fixed shelf for mounting 234.00 HORIZONTAL COMPARTMENT SHELVING: 1.25 (1) Fixed aluminum divider tray with removable dividers 168.00 1.26 (1) Fixed aluminum open shelf 109.00 Aluminum pull-out drawer on slides: 2" deep with dividers on 2" centers, 1.27 Mounted on full extension Grant sides must include price of fixed shelf for mounting 234.00 ADDITIONAL COMPARTMENT OPTIONS: 1.28 8 drawer metal cabinet installed 258.00 1.29 9 drawer metal cabinet installed 258.00 1.3 6 drawer metal cabinet installed 225.00 1.31 18 drawer metal cabinet installed 378.00 1.32 Hotstick door only 232.00 1.33 Hotstick door with full-lengh fiberglass shelf 504.00 1.34 Full-length fiberglass shelf 239.00 1.35 Pull-out tool box tray (250# capacity) 750.00

COMPARTMENT ACCESSORIES: 1.36 Gas door shocks (per compartment) for vertical doors 80.00 1.37 Swivel hook (per hook) 35.00 1.38 Fixed hook (per hook) 22.00 1.39 LED Flexible tube lighting (per compartment) three sides of the 95.00 Compartment opening BODY COMPONENTS: 1/8" aluminum tread plate floor and subframe in lieu of steel 1.40 40" tall 96" body 314.00 1.41 40" tall 108" body 544.00 1.42 40" tall 132" body 640.00 1/8" aluminum treadplate floor and subframe in lieu of steel 1.43 High Side 96" body 559.00 1.44 48" tall 108" body 1,319.00 1.45 48" tall 132" body 1,417.00 GELCOAT COLORS: Gelcoat "Blended White" to be close match to Truck Manufactures Std white paint code Gelcoat charge other than white (does not include metallic or black colors) 1.46 96" body 400.00 1.47 108" body 450.00 1.48 132" body 575.00 EXTERIOR BODY ACCESSORIES: 1.49 Pipe vice table and rest 225.00 1.50 Material rail and (6) hooks 420.00 1.51 Crane reinforcement for 25,000 ft. lb. Installed in rear vertical compartment 1,635.00 1.52 Fiberglass sliding top with double rear doors. 1,862.00 1.53 Expanded metal aluminum shovel basket up to 132" long and 8" high 490.00 1.54 Oxygen/acetylene tank holder (each) 125.00 1.55 Aluminum post for strobe (above cab top) 102.00 1.56 Aluminum expanded metal cab guard, tube frame with expanded metal 579.00 BUMPERS: 1.62 8" non recessed steel treadplate bumper 405.00 1.63 8" recessed steel treadplate bumper with saftey chain "D" rings 458.00 1.64 8" non recessed steel gripstrut bumper 495.00 1.65 8" recessed steel gripstrut bumper with saftey chain "D" rings 578.00 1.66 8" non recessed aluminum Treade-Brite bumper 458.00 1.67 8" recessed aluminum Treade-Brite with saftey chain "D" rings 510.00 LOADBED AND COMPARTMENT TOPS: Aluminum Tread-Brite on loaded walls (96" Body) 1.68 35" & 40" high 567.00 1.69 High side 662.00

Aluminum Tread-Brite on loaded walls (108" Body) 1.70 40" high 638.00 1.71 48" high 957.00 Aluminum Tread-Brite on loaded walls (132" Body) 1.72 40" high 869.00 1.73 48" high 1,262.00 Aluminum Tread-Brite on compartment tops 1.74 96" body 567.00 1.75 108" body 662.00 1.76 132" body 869.00 FIBERGLASS FLIP-TOP COMPARTMENT (WITH 3" DEEP DIVIDER TRAY): 1.77 Flip-top for 96" body (per side) 914.00 1.78 Flip-top for 108" body (per side) 914.00 LATCHS AND LOCKING SYSTEMS 1.79 Stainless steel 3-point D-ring latch (price per door) 97.00 Gang-locking system 1.80 96" body 660.00 1.81 108" body 660.00 1.82 132" body 879.00 Electric door locks, locks all doors with one FOB 1.83 96" body 1,275.00 1.84 108" body 1,275.00 1.85 132" body 1,700.00 TRANSVERSE COMPARTMENT AND OPTIONS: 1.86 Steel tread plate transverse open to one side 420.00 1.87 Aluminum Treade-Brite transverse open to one side 434.00 1.88 Transverse open to both sides (either steel and aluminum) 87.00 1.89 Rack and one drawer - pull one side 2/3rd's length 532.00 1.90 Rack and two drawers - pull one side 2/3rd's length 818.00 1.91 Rack Cage and three drawers - pull one side 2/3rd's length 968.00 1.92 Rack and one drawer - pull both sides full length 562.00 1.93 Rack and two drawers - pull both sides full length 875.00 1.94 Rack and three drawers - pull both sides full length 1,202.00 1.95 Fixed transverse shelf - 2/3rd's length 234.00 1.96 Fixed transverse shelf - full length 259.00 LADDER AND PIPE RACK: 1.97 Bow ladder rack (steel) 442.00

1.98 Bow ladder rack (aluminum) 530.00 1.99 Side mount ladder rack (steel) 318.00 1.100 Side mount ladder rack (aluminum) 494.00 1.101 Horizontal ladder rack with roller (steel) 505.00 1.102 Horizontal ladder rack with roller (aluminum) 594.00 1.103 Slanted steel pipe rack 312.00 1.104 Furnish and install aluminum pipe rack 312.00 1.105 Ladder rack over center lock 150.00 1.106 6" PVC tube with aluminum end caps 325.00 GRAB HANDLES: 1.107 Furnish and install grab handle (each) 42.00 2.133 Basic Installation of Fiberline Fiberglass Bodies 895.00 2.134 Installation Kit 125.00 2.135 Light plug adaptor 75.00 2.136 Installation of OEM Supplied Backup Camera 100.00 2.137 Provided and install Standard Rostra OEM Compatable Camera 250.00 2.138 Provide and install HD Rostra OEM Compatable Camera 310.00 Cost per mile for pick-up or Delivery to or from Moorhead, MN 2.25 (Maximum charge per unit for pick-up/delivery one way 425.00) Buyer sguide for pricing Service Body: Chassis CA SW DW Make and Model of Chassis: Base Body Shelving Package Bumper Installation BASIC PACKAGE TOTAL Additional Options: Delivery (max 425.00 one way) Total Package Body and Equipment By: Bert s Truck Equipment Inc. Jim McLaughlin, Commercial Fleet Sales 3804 Hwy 75 North Moorhead, MN 56560 800-232-3787, 218-233-8681 Fax 218-233-9548

Email: jimmc@bertsonline.com Web Site: www.bertsonline.com

Service Bodies Contract end Date 09-30-18 Vendor Name: Bert's Truck Equipment, Inc Contact Person: Jim McLaughlin Street Address: 3804 Highway 75 North P.O. Box: 336 City, State, Zip Moorhead, MN 56561-0336 Phone #: 218-233-8681 Toll Free #: 800-232-3787 Fax #: 218-233-9548 Email Address: jimmc@bertsonline.com Website: www.bertsonline.com Version of Excel used: 2013 Furnish separate price quote for: BODY COMPONENTS AND ATTACHMENTS FOR 6,000 1.0 UTILITY /SERVICE BODY Make Warranty Date & I.D. of Price List Altec/Astoria Fibergalss Utility Bodies 5 Year Limited Warranty 11/30/2017 Discount to be applied to Price List* (see note below) 0.00% Installation of Utility/Service Body as per MnDOT spec 1.0 See Attached Price Schedule Price of FMVSS 108 lighting package See Attached Price Schedule Price of ICC bumper under ride protection See Attached Price Schedule Installation of ICC bumper under the protection See Attached Price Schedule Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Moorhead, MN 56560 Price per loaded mile for delivery 2.25 Delivery Time Frame in calendar days ARO 120-180 Shop Rate per Hour Shop Rate for Mechanical work 100.00 Body Shop Rate 100.00 *Note: The "Discount to be Applied to Price List" must be a

Altec Fiberglass Utility Body State of Minnesota 11/30/2017 Pricing Page STANDARD BODY EQUIPMENT INCLUDES: Six Year Warranty (limited) Molded fiberglass side compartments Gelcoat exterior finish (stock white) Fiberglass reinforced double laminated doors Heavy duty stainless steel hinges Heavy duty strikers Automotive bulb door gasket seal 12 ga steel treadplate floor, primed and with black gatorhyde finish Universal Steel structural body frame with Rigid Mounting Kit Flush mounted tail and back-up lights FMVSS 108 lighting package Corrosion resistant fasteners All self-locking nuts Compartment drains Stainless steel rotary paddle latches License plate bracket with light Loomed wiring harness Extruded aluminum drip rail Full height fiberglass bulkheads between compartments Non skid finish on module tops Fuel filler cone Louvered vents in each modules Door chain stops all door Aluminum rock guards on front corners Aluminum trim on inside edged of module Rubber Fenders **All body side pack depth canbe increased in depth from1 5 deep up to24 deep at No Charge Charge ** RECYCLED FIBERGLASS CORE BODY ** EXTERIOR STEEL PARTS FINISHED WITH BLACK GATORHYDE FINISH Standard body for Single Rear Wheel 56 CA application Chassis CA Dimension 56 Body Length 96 Body Width 79 Body Height 39 Compartment Depth 15 Make & Model LGS-96-56 1.0-1 Price 11,320.00 Standard body for Dual Rear Wheel 56 CA application Chassis CA Dimension 56 Body Length 96 Body Width 94 Body Height 39 Compartment Depth 20

Make & Model LGS-96-56 Price 11,445.00 Tall body for Single Rear Wheel 56 CA application Chassis CA Dimension 56 Body Length 96 Body Width 79 Body Height 48 Compartment Depth 15 Make & Model ASL-96-56 1.0-2 Price 12,186.00 Tall body for Dual Rear Wheel 56 CA application Chassis CA Dimension 56 Body Length 96 Body Width 94 Body Height 48 Compartment Depth 20 Make & Model ASL-96-56 Price 12,311.00 Standard body for Single Rear Wheel 60 CA application Chassis CA Dimension 60 Body Length 108 Body Width 79 Body Height 39 Compartment Depth 15 Make & Model LGS-108-60 1.0-3 Price 11,474.00 Standard body for Dual Rear Wheel 60 CA application Chassis CA Dimension 60 Body Length 108 Body Width 94 Body Height 39 Compartment Depth 20 Make & Model LGS-108-60 1.0-4 Price 11,599.00 Tall body for Single Rear Wheel 60 CA application Chassis CA Dimension 60 Body Length 108 Body Width 79 Body Height 48 Compartment Depth 15 Make & Model ASL-108-60 1.0-5 Price 13,325.00 Tall body for Dual Rear Wheel 60 CA application Chassis CA Dimension 60 Body Length 108 Body Width 94 Body Height 48 Compartment Depth 20

Make & Model ASL-108-60 1.0-6 Price 13,650.00 Standard body for Dual Rear Wheel 84 CA application Chassis CA Dimension 84 Body Length 132 Body Width 94 Body Height 39 Compartment Depth 20 Make & Model LGS-132-84 1.0-7 Price 13,885.00 Tall body for Dual Rear Wheel 84 CA application Chassis CA Dimension 84 Body Length 132 Body Width 94 Body Height 48 Compartment Depth 18 Make & Model ASL-132-84 1.0-8 Price 16,366.00 BODY OPTIONS: Standard shelving package for all bodies up to 108 length: adjustable fiberglass shelves in each front vertical compartment: fixed fiberglass shelf with removable dividers in streetside horizontal compartment adjustable fiberglass shelf each rear compartment 1.0-9 Price 922.00 Standard shelving package for all 132 length bodies: adjustable shelves in each front vertical compartments adjustable shelves in 2ndvertical compartment Fixed shelf with removable dividers in streetside horizontal compartment adjustable fiberglass shelf each rear compartment Price 1,420.00 BODY OPTIONS: Vertical Compartment Shelving: 1.2 Adjustable fiberglass shelf with removable dividers 125.00 Aluminum pull-out drawer on slides: 2 deep with dividers on 4 centers, 1.21 sliders rated at 100# at full extension (price per drawer) 211.00 * Price must include the cost of a fixed shelf or required mounting Hardware necessary to support drawers. HORIZONTAL COMPARTMENT SHELVING: 1.22 Fixed fiberglass shelf with removable dividers 173.00 1.23 Divider tray on bottom of compartment 173.00 ADDITIONAL COMPARTMENT SHELVING:

1.24 8 drawer metal cabinet installed 181.00 1.25 9 drawer metal cabinet installed 163.00 1.26 6 drawer metal cabinet installed 133.00 (1 row of 6) 1.27 18 drawer metal cabinet installed 380.00 1.28 Hotstick door only 157.00 1.29 Full-length fiberglass shelf 266.00 1.3 Hotstick door with thru shelf 421.00 SHELVING ACCESSORIES: 1.31 Rubber spaghetti matting (per shelf price) 26.00 1.32 Material rail with (4) hooks 160.00 COMPARTMENT ACCESSORIES: 1.33 Locking swivel hook (per hook) 32.00 1.34 LED cargo area light/flush-mount 4 diameter 135.00 1.35 Vent in back wall of compartment 39.00 1.36 Flexible tubular LED lighting (per compartment) three sides of the 147.00 Compartment opening 1.37 Adhesive Strip Lighting (LED) Around Top And Sides Of Compartment Door Facings 147.00 BODY COMPONENTS: Upgrade to 3/16 aluminum treadplatefloor and aluminumunder structure in lieu of 12gasteel floor and steel understructure (39" tall bodies) 1.38 96" body 251.00 1.39 108" body 392.00 1.4 132" body 477.00 Upgrade to 3/16 aluminum treadplate floor and aluminum understructure in lieu of 12ga steel floor and steel understructure (48" tall bodies) 1.41 96" body 251.00 1.42 108" body 392.00 1.43 132" body 477.00 Body shall be installed per FMVSS using a four point spring mounting system plus mid support tube Included Included

Quick plug wiring adapter GELCOAT/PAINT: Non Standard Gel Coat Adder (no metallic finishes) * Altec does not guarantee color matches - must provide color swatch at time of order 39" Tall Bodies 1.44 96" long 1,282.00 1.45 108" long 1,442.00 1.46 132" long 1,762.00 48" Tall Bodies 1.47 96" long 1,347.00 1.48 108" Long 1,517.00 1.49 132" long 1,853.00 EXTERIOR BODY ACCESSORIES: 1.5 Spare tire mount 82.00 1.51 Water cask holder 160.00 1.52 Double overlapping door (132 bodies only) 219.00 1.53 Aluminum cone holder (vertical storage) 128.00 1.54 Bolt On Steel Vise Bracket 192.00 1.55 60" Aluminum material rail and (6) hooks 305.00 1.56 Crane reinforcement for 25,000 ft. lb. Installed in rear vertical 1,477.00 compartment 1.57 Fiberglass roll top with double rear doors. 1,799.00 Laser cut aluminum shovel basket up to 132 L x 8"H x 20"W 563.00 1.58 1.59 Combination Fuel and DEF fuel cone 65.00 1.6 D Ring Recessed in Body Floor (per D Ring) 91.00 1.61 Oxygen/acetylene tank holder (each) 134.00 1.62 Aluminum riser post for strobe 65.00 (above cab level) 1.63 Aluminum cab guard (headache rack), tube frame with expanded metal screen 599.00