CODE 715 BODY SHOP EQUIPMENT 225 Electrostatic painting equipment allows the paint to wrap around the product being sprayed. Electrostatic wrap is achieved by charging the paint with a static charge. Once charged, the paint being sprayed will be attracted to the nearest grounded object, and will disperse evenly over the entire surface. Its high efficiency charging system is variable up to 80 kv. A trigger mounted electrostatic on/off switch has been designed for operator convenience. Corrosion resistant wetted parts allow applications of chlorinated solvent thinned coatings (requires special supply pump). (Note: This system is also available as a special order in a similar version for water base coatings. The water base coating requires testing to determine its suitability.) VM2000 Conversion Kit Model L013-007 The high voltage setting is adjustable from 0 to 80 kv. Applications include practically any metal object that can be grounded and requires a decorative and/or protective finish with a solvent borne paint coating. VM2000 Portable System Model L013-008 The Portable System is a truly portable electrostatic. Hose and cable are available up to 100 in length. Boxer A928 HVLP Complete System Model L014-002 The Boxer HVLP professional spray system is perfect for finishing shops, production lines, and contractors. Materials which can be sprayed include varnish, urethane, lacquer, automotive paint, epoxy, enamel, stain, latex, bases oil base, adhesives, etc. Specifications Model L014-002 A-928 Spray Gun Nozzle (Std) 1.5 mm Pressure Range 1-125 PSI Volume Output (Max) 1.3 gpm Max. Hose Length 100 (ID) Pump Type Double diaphragm Diaphragm Material Teflon Air Consumption (Pump) 2 cfm @ 20 PSI Air Consumption (Gun) 10 cfm @ 70 PSI
226 BODY SHOP EQUIPMENT CODE 715 Air/Airless Paint System Model AirCombi The combination of high airless fluid pressure (500 2,000 PSI) and low atomizing air pressure (5-50 PSI) gives the best of both air and airless qualities. The Air Combi gun will hook-up to any airless pump which will deliver between 500 and 2,000 PSI. A small air compressor delivering about 5 cfm (free flow) is sufficient for the atomizing air when using light materials. The paint, lacquer, varnish or other coating is delivered through an airless tip at low pressure (typically 500 to 800 PSI). The operator can adjust the paint flow rate by changing the pressure at the airless pump and he will not reduce atomizing efficiency. Dual regulators with gauges to control fluid and air cap pressure Wiwa pneumatic pump: 33:1 ratio, 3.3 l./min., self adjusting packings High pressure filter with gauge keeps spray tip from clogging and shows fluid pressure High pressure twin line hose using highest quality hoses for safety Air Combi gun: 3,500 PSI maximum fluid, 50 PSI maximum air, stainless steel & tungsten fluid path. T95 HVLP Turbine System Model L080-044 The T95 is equipped with a 2-quart remote and internal compressor which makes it the perfect system for larger jobs. The industrial high volume air intake filter supplies clean air to the powerful yet quiet 3 stage turbine. It supplies warm dry air to the all metal A-710S bleeder type gun. The T-95 sprays all conventional coatings including lacquer, enamel, latex, stain, multi color, and other materials.
CODE 715 BODY SHOP EQUIPMENT 227 P2900 30:1 Rust Proofing Pail Pump (0.019 max) Model L280-002 This 1.2 L per minute pump is capable of pumping medium thick materials. Its output easily holds the spraying pressure at maximum thereby maintaining a perfect spray pattern. P2900 12:1 Rust Proofing Barrel Pump (0.035 max) Models L277-001 / L277-002 This large volume 4 L per minute pump is capable of pumping thick materials. Its high volume output easily holds the spraying pressure at maximum thereby maintaining a perfect spray pattern. All Stainless fluid ends No air lubrication required. Model L277-001: 60-litre keg size Model L277-002: 205-litre drum size 2.25-Gallon Pressure Pot Rust Proofing Kit Model L011-080 The A-910 gun atomizes the material by mixing air with the product in the gun s spray head. The wand included with the system has an angled metal Venturi nozzle with a heavy-duty flexible rubber hose. It produces a conical spray pattern for general purpose applications. No sticking valves No pumps to repair No priming Uses compressed air. A460 Rust Proofing Kit complete Model L015-200 The A-460 internal mix gun atomizes the material by mixing air with the product in the gun s spray head. The wand included with the system has an angled metal venturi nozzle with a heavy-duty flexible rubber hose. It produces a conical spray pattern for general applications.
BODY SHOP EQUIPMENT CODE 860 228 Undercoating Pumps Materials may be sprayed using air-atomizing or airless spray systems. Applications include the spraying of adhesives, roof coatings and hundreds of similar applications. Air inlet: 1/4 NPTF(f) Material outlet: 3/8 NPTF(f) H-Pump air motor diameter: 2-7/16 Double-toggle balances pressure on air valve trip mechanism to prevent binding or stalling Corrosion-resistant chrome finish on piston rods alleviates packing wear. Specifications Product # 331571-A5 331571-B5 331571-C5 8553-2 Description Stationary H-Pump Stationary H-Pump Stationary H-Pump Portable H-Pump Drum Size 120 lbs. 400 lbs. 35 lbs. 35 lbs. Pump Ratio 26:1 26:1 26:1 26:1 Delivery 5.25 lbs. 5.25 lbs. 5.25 lbs. 5.25 lbs. per min. CODE 001 1513A Collision Repair Set Models 1513A / 1515A Industry standard couplers are interchangeable with leading manufacturer s units Snap together design of extension tubes allows for easy assembly Automatic overload system on pump protects against damage to equipment 1/2-ton hydraulic spreader tool has 2 jaws that spread from 5/8 to 3-3/8. 1513A: 4-ton 1515A: 10-ton 1515A
CODE 484 BODY SHOP EQUIPMENT 229 10-Ton Collision Repair Set Model 440 Kit includes: Hydraulic pump, standard ram, plastic blow mould case, 19-1/2 extension tube, 16-1/2 extension tube, 8-1/2 extension tube, 5 extension tube, quick connector, serrated saddle, spreader ram, rubber head, hedge head, spreader ram toe, spreader plunger toe, rubber faced flat base, 90 v-base, hose. 4-Ton Collision Repair Set Model 439 Kit includes: Hydraulic pump, standard 4-ton ram, plastic blow mould case, 19-1/2 extension tube, 16-1/2 extension tube, 8-1/2 extension tube, 5 extension tube, 3/4 extension tube, serrated saddle, spreader ram 1/2 ton, rubber head, wedge head, spreader ram toe, spreader plunger toe, rubber faced flat base, hose, 90 V-base and SS connector. Vehicle Door Remover/Installer Model 245 Simplifies the job of removing and installing vehicle doors and lines up hinge assemblies effortlessly! 440 439 245
230 BODY SHOP EQUIPMENT CODE 068 Door Stand Model DAS-100 Remove and install doors effortlessly with a single person! No more back strains! Clamp the door and the stand adjusts in multi directions - in and out, tilt forward or backward, up or down. All adjustments are with a power ratchet, no handles to turn. Paint Shaker with Oiler Model 9000 Capacity 4 Litre Speed - 700 (cycles/min) Shaking time - 1.5 minute. Paint Shaker Stand Model PSS-1 Paint Shaker with Stand Model 9000/PSS-1 DAS-100 9000 PSS-1
CODE 068 BODY SHOP EQUIPMENT 231 Single Thinner Dispenser Model CD-1 5 Gallons Double Thinner Dispenser Model CD-2 2 x 5 Gallons Masking Machine Model MM-18 18 portable, heavy-duty, dual delivery masking machine. Masking Machine Model MM-36 36 portable, heavy-duty, dual delivery masking machine. Paper/Film Dispenser Model MPD-38 38 paper or film dispenser. Can be mounted on wall, bench or floor. Masking Machines Models MM-500-18 / MM-500-24 18 and 24 portable, deluxe masking machines (two-roll capacity). CD-1 Masking Machine Model MM-500-42 42 portable, deluxe masking machine (three-roll capacity). MM-500-18 / MM-500-24 CD-2 MM-500-42
232 BODY SHOP EQUIPMENT CODE 345 With ISOColor technology the light intensity is displayed in colors allowing the service mechanic to pinpoint perfect alignment every time. Tested by Intertec Testing Services, an AMECA approved laboratory and found to exceed the SAE Standards J599 Lighting Inspection Code, and J600 Headlamp Aim Testing Machines. Approved for use in all province s inspection programs that accept visual systems. Headlight Aligner Model SCA 1 Defines the High Intensity Zone for precise alignment every time. The new color pattern technology is your fastest path to perfect alignment. Five easy steps: position, square up, switch to desired beam pattern, center on lamp, adjust, and move next to lamp. Benefits Durable and lightweight Adjustable height Laser floor slope Field calibration Accurate/repeatable Compact and portable Rotational mast Non-electronic Economical cost. Headlight Aligner Model CVA3 EZ Technology combined with Visual Assist precision! SCA1 Sighting Unit Squares the CVA 3EZ to the vehicle by use of a sight line that is aligned with two common points on the vehicle Beam Selection Switch selects the beam pattern to be aligned Laser Floor Slope Measurement is accurate, precise and simple to achieve ISO Color Revolutionary color technology takes the guesswork out of headlamp alignment Floor Slope Adjustment is easily attained by rotation of the eccentric wheel Rotating Mast Rotating mast allows for easy alignment of optical head to vehicle Fresnel Lens Precision engineered Fresnel lens provides the optics that enables the technician to view headlamps as they appear at 25 Step-by-Step Easy to follow procedures located on the optical head Visual Assist Meter When meter reading reaches highest level, alignment is complete! Benefits Heavy-duty Construction User friendly Visual assist meter Minimal maintenance Portable Laser floor slope adjustment. CVA3