STD 093/6/4 1 November 2015 ULASAN UMUM BAGI DRAF MALAYSIAN STANDARDS YANG SEDANG DIBANGUNKAN, BAGI TEMPOH 1 NOVEMBER 2015 31 DISEMBER 2015 Dengan segala hormatnya perkara di atas adalah dirujuk. Bersama sama ini disertakan senarai draf Malaysian Standards (MS) yang sedang dibangunkan seperti di Lampiran A dan senarai Malaysian Standard yang disyorkan untuk ditarik balik tanpa diganti seperti di Lampiran B untuk ulasan umum. Draf-draf Malaysian Standards tersebut adalah mengenai pelbagai barangan, proses-proses dan tatasusila amalan dalam pelbagai bidang industri yang dibangunkan di bawah Jawatankuasa Standard Perindustrian (ISC) di SIRIM Berhad. Jadual pecahan jumlah draf-draf dan Malaysian Standards tersebut mengikut ISC disertakan di lampiran. Penyediaan draf-draf Malaysian Standards tersebut telah dibuat oleh jawatankuasa berkaitan yang ditubuhkan di SIRIM Berhad yang diwakili oleh pihak industri, kementerian, agensi-agensi kerajaan, institusi pengajian tinggi dan orang perseorangan yang pakar dalam bidang berkenaan. Sehubungan dengan itu, pihak SIRIM Berhad mengalu-alukan sebarang ulasan ke atas draf-draf dan penarikan balik Malaysian Standards tersebut. Bagi mereka yang bukan ahli bagi mana-mana ISC, draf-draf Malaysian Standards yang diterima pakai (adopted) dari standard ISO/IEC, ASTM dan EN boleh diperolehi dengan bayaran seperti tertera. Bayaran boleh dibuat secara tunai/cek dengan tambahan 10% bagi bayaran pos kepada SIRIM Berhad. Tuan/puan juga boleh menyemak dokumen tersebut secara percuma dengan datang sendiri ke Pusat Pengurusan dan Penyelidikan Standard, Tingkat 2, Bangunan 3, SIRIM Berhad. Draf-draf untuk ulasan umum boleh diperolehi daripada: SIRIM Berhad (u.p.: Pusat Pengurusan dan Penyelidikan Standard) Tel: 603-55446311 / 603-55446389 Fax: 603-55108830 / 603-55446333 E-mail: stddevelop@sirim.my Website: http://www.smsonline.gov.my/ SIRIM Berhad (Company No. 367474 - V) 1, Persiaran Dato Menteri Section 2, P. 0. Box 7035 40700 Shah Alam MALAYSIA Tel: 60-3-55446000 Hotline: 60-3- 55103535 Fax: 60-3-55108095 http://www.sirim.my Dimaklumkan juga bahawa draf-draf Malaysian Standards tersebut masih dalam peringkat penyediaan dan tertakluk kepada pindaan dan bukan digunakan untuk rujukan rasmi sebagai Malaysian Standards. Memandangkan draf-draf tersebut juga adalah hakcipta organisasiorganisasi yang berkenaan seperti STANDARDS MALAYSIA, ISO/IEC, ASTM dan CEN, tuan/puan adalah dilarang daripada membuat salinan dan mengedarkannya kepada pihak lain. Semua ulasan hendaklah sampai ke SIRIM Berhad selewat-lewatnya pada: 31 DISEMBER 2015
Kami juga berharap untuk mendapat kerjasama daripada pihak tuan/puan agar dapat membuat pautan laman sesawang organisasi tuan/puan kepada laman sesawang kami di http://www.smsonline.gov.my/ bagi tujuan pemberitahuan kepada ahli pertubuhan dan organisasi tuan/puan. Kerjasama serta sokongan tuan/puan dalam perkara ini diharap akan dapat memajukan lagi aktiviti-aktiviti standardisasi negara kita. Sekian terima kasih. Yang ikhlas, Azlina Abd Latif Ketua Seksyen Operasi dan Sistem Standard Pusat Pengurusan dan Penyelidikan Standard SIRIM Berhad s.k. Pengurus Besar Kanan Pusat Pengurusan dan Penyelidikan Standard
JADUAL BAGI JUMLAH DRAF MALAYSIAN STANDARDS YANG SEDANG DIBANGUNKAN UNTUK ULASAN UMUM BAGI TEMPOH 1 NOVEMBER 2015 31 DISEMBER 2015 KOD ISC A Pertanian TAJUK ISC BIL. DRAF MALAYSIAN STANDARDS YANG SEDANG DIBANGUNKAN BIL. DRAF MALAYSIAN STANDARDS DISYORKAN UNTUK DITARIK BALIK TANPA DIGANTI D Bangunan, Pembinaan dan Kejuruteraan Awam E F G H K L M N P Q R S T U W Y Z Penjanaan, Transmisi dan Pengagihan Tenaga Kejuruteraan Mekanikal Teknologi Maklumat, Komunikasi dan Multimedia Petroleum dan Gas Pembungkusan dan Logistik Kenderaan Jalan Pencegahan dan Keselamatan Kebakaran Getah dan Barangan Getah Bahan Logam dan Barangan Separuh Siap Tekstil dan Pakaian Peralatan Perubatan dan Kemudahan untuk Penjagaan Kesihatan Peralatan dan Aksesori Elektrik dan Elektronik Pelancongan, Pameran dan Perkhidmatan Mesra Makanan, Produk Makanan dan Keselamatan Makanan Keselamatan dan Kesihatan Pekerjaan Pengurusan Kualiti dan Penentuan Kualiti Pengurusan Alam Sekitar 4 31 2 1 1 24 3 3 Jumlah 9 60
LAMPIRAN A LIST OF DRAFT MALAYSIAN STANDARDS FOR PUBLIC COMMENT: 01/11/2015-31/12/2015 ISC E: Generation, Transmission and Distribution of Energy 1. 15E018R1 High-voltage switchgear and controlgear - Part 100: Alternating current ( RM 400.00 ) circuit-breakers (First revision) (IEC 62271-100:2012, IDT) 2. 15E019R1 ( RM 60.00 ) 3. 15E020R1 ( RM 90.00 ) 4. 15E021R1 ( RM 80.00 ) High-voltage switchgear and controlgear - Part 105: Alternating current switch-fuse combinations for rated voltages above 1 kv up to and including 52 kv (First revision) (IEC 62271-105:2012, IDT) High-voltage switchgear and controlgear - Part 200: AC metal enclosed switchgear and controlgear for rated voltages above 1 kv and up to and including 52 kv (First revision) (IEC 62271-200:2011, IDT) High-voltage switchgear and controlgear - Part 203: Gas-insulated metalenclosed switchgear for rated voltages above 52 kv (First revision) (IEC 62271-203:2011, MOD) ISC R: Medical Devices and Facilities for Healthcare 1. 14R001R0 Magnetic Resonance Imaging (MRI) systems acceptance tests and quality control (QC) - Guidelines ISC S: Electrical and Electronics Equipments and Accessories 1. 15S023R2 Explosive atmospheres - Part 17: Electrical installations, inspection and ( RM 40.00 ) maintenance (Second revision) (IEC 60079-17:2013, IDT) ISC W: Occupational Safety and Health 1. 15W001R1 Safety of machinery - Pressure-sensitive protective devices - Part 1: ( RM 60.00 ) General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors (First revision) (ISO 13856-1:2013, IDT) 2. 15W002R1 ( RM 70.00 ) 3. 15W003R1 ( RM 70.00 ) Safety of machinery - Pressure-sensitive protective devices - Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars (First revision) (ISO 13856-2:2013, IDT) Safety of machinery - Pressure-sensitive protective devices - Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices (First revision) (ISO 13856-3:2013, IDT)
LAMPIRAN B LIST OF MALAYSIAN STANDARDS PROPOSED FOR WITHDRAWAL (WITH NO REPLACEMENT) FOR PUBLIC COMMENT: 01/11/2015-31/12/2015 No. MS Number MS Title ISC 1 MS IEC 60034-1:2005 - PART 1: RATING AND PERFORMANCE (IEC 60034-1:2004, IDT) 2 MS IEC 60034-12:2007 3 MS IEC 60034-14:2007 4 MS IEC 60034-15:2007 5 MS IEC 60034-16-1:2007 6 MS IEC 60034-18-1:2007 7 MS IEC 60034-18-21:2007 8 MS IEC 60034-18-31:2007 - PART 12: STARTING PERFORMANCE OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS (IEC 60034-12:2002, IDT) - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY (IEC 60034-14:2003, IDT) - PART 15: IMPULSE VOLTAGE WITHSTAND LEVELS OF ROTATING A.C. MACHINES WITH FORM- WOUND STATOR COILS (IEC 60034-15:1995, IDT) - PART 16: EXCITATION SYSTEMS FOR SYNCHRONOUS MACHINES - CHAPTER 1: DEFINITIONS (IEC 60034-16-1:1991, IDT) - PART 18: FUNCTIONAL SYSTEMS - SECTION 1: GENERAL GUIDELINES (IEC 60034-18-1:1992 AND AMENDMENT 1:1996, IDT) - PART 18: FUNCTIONAL SYSTEMS - SECTION 21: TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION - PART 18: FUNCTIONAL SYSTEMS - SECTION 31: TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN MACHINES UP TO AND INCLUDING 50 MVA AND 15 KV (IEC 60034-18- 31:1992, IDT)
9 MS IEC 60034-18-32:2007 - PART 18: FUNCTIONAL SYSTEMS - SECTION 32: TEST PROCEDURES FOR FORM-WOUND WINDINGS - ELECTRICAL SYSTEMS USED IN MACHINES UP TO AND INCLUDING 50 MVA AND 15 KV 10 MS IEC 60034-2:2004 11 MS IEC 60034-5:2006 12 MS IEC 60034-9:2007 13 MS IEC 60747-1:2007 14 MS IEC 60974-1:2005 15 MS IEC 61010-2-010:2008 16 MS IEC 61010-2-032:2008 - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF ROTATING ELECTRICAL MACHINERY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES) (IEC 34-2:1972, IEC 34-2A:1974, AMD.1:1995 AND AMD.2:1996, IDT) - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION (IEC 60034-5:2000, IDT) - PART 9: NOISE LIMITS (IEC 60034-9:2003, IDT) SEMICONDUCTOR DEVICES - PART 1: GENERAL (IEC 60747-1:2006, IDT) ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES (IEC 60974-1:2000 AND AMENDMENT 2:2003, IDT) SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 2-010: PARTICULAR REQUIREMENTS FOR LABORATORY EQUIPMENT FOR THE HEATING OF MATERIALS (IEC 61010-2-010:2005, IDT) SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-032: PARTICULAR REQUIREMENTS FOR HAND-HELD AND HAND- MANIPULATED CURRENT SENSORS FOR ELECTRICAL TEST AND MEASUREMENT (IEC 61010-2- 032:2002, IDT) E 3/6/2015 TC agreed to withdraw
17 MS IEC 61010-2-051:2008 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL, AND LABORATORY USE - PART 2-051: PARTICULAR REQUIREMENTS FOR LABORATORY EQUIPMENT FOR MIXING AND STIRRING (IEC 61010-2-051:2005, IDT) 18 MS IEC 61010-2-081:2008 19 MS IEC/TS 60034-18- 33:2007 20 MS IEC/TS 60034-18- 34:2007 21 MS IEC/TS 60034-18- 41:2007 22 MS IEC 60432-1:2006 23 MS IEC 60432-2:2006 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 2-081: PARTICULAR REQUIREMENTS FOR AUTOMATIC AND SEMI-AUTOMATIC LABORATORY EQUIPMENT FOR ANALYSIS AND OTHER PURPOSES (IEC 61010-2-081:2001 & AMD. 1:2003, IDT) - PART 18: FUNCTIONAL SYSTEMS - SECTION 33: TEST PROCEDURES FOR FORM-WOUND WINDINGS - MULTIFACTOR FUNCTIONAL EVALUATION - ENDURANCE UNDER COMBINED THERMAL AND ELECTRICAL STRESSES OF INSULATION SYSTEMS - PART 18-34: FUNCTIONAL SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - EVALUATION OF THERMOMECHANICAL ENDURANCE OF INSULATION SYSTEMS - PART 18-41: QUALIFICATION AND TYPE TESTS FOR TYPE I ELECTRICAL INSULATION SYSTEMS USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS INCANDESCENT LAMPS - SAFETY SPECIFICATIONS - PART 1: TUNGSTEN FILAMENT LAMPS FOR DOMESTIC AND SIMILAR GENERAL LIGHTING PURPOSES (FIRST REVISION) (IEC 60432-1:2005, IDT) INCANDESCENT LAMPS - SAFETY SPECIFICATIONS - PART 2: TUNGSTEN HALOGEN LAMPS FOR DOMESTIC AND SIMILAR GENERAL LIGHTING PURPOSES (FIRST REVISION) (IEC 60432-2:2005, IDT) S 12/5/2015 TC/S/3 agreed to withdraw the MS and direct S 12/5/2015 TC/S/3 agreed to withdraw the MS and direct
24 MS IEC 60432-3:2006 INCANDESCENT LAMPS - SAFETY SPECIFICATIONS - PART 3: TUNGSTEN-HALOGEN LAMPS (NON-VEHICLE) (IEC 60432-3:2005, S 12/5/2015 TC/S/3 agreed to withdraw the MS and direct IDT) 25 MS IEC 60721-2-2:2004 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS Â PART 2-2: ENVIRONMENTAL CONDITIONS APPEARING IN NATURE Â PRECIPITATION AND WIND (IEC 60721-2-2:1988, IDT) 26 MS 1177:1990 GUIDE TO THE DETERMINATION AND USE OF QUALITY RELATED COSTS 27 MS 558:1978 CODE OF PRACTICE FOR THE PRESENTATION OF NUMERICAL VALUES 28 MS ISO 1000:2000 SI UNITS AND RECOMMENDATIONS FOR THE USE OF THEIR MULTIPLES AND OF CERTAIN OTHER UNITS (ISO 1000:1992 AND ITS AMENDMENT 1:1998, IDT) 29 MS 2387:2010 MAGNETIC MATERIALS - PART 8-4: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - COLD-ROLLED NON- ORIENTED ELECTRICAL STEEL SHEET AND STRIP DELIVERED IN THE FULLY-PROCESSED STATE (IEC 60404-8-4:1998, MOD) 30 MS IEC 60404-8-7:2010 31 MS IEC 60183:2003 32 MS IEC 60228:2001 33 MS IEC 60229:2001 34 MS IEC 60287-1-2:2001 MAGNETIC MATERIALS - PART 8-7: SPECIFICATION FOR INDIVIDUAL MATERIALS - COLD-ROLLED GRAIN- ORIENTED ELECTRICAL STEEL STRIP AND SHEET DELIVERED IN THE FULLY-PROCESSED STATE (IEC 60404-8-7:2008, IDT) GUIDE TO THE SELECTION OF HIGH-VOLTAGE CABLES (IEC 60183:1984 AND ITS AMENDMENT 1:1990, IDT) CONDUCTORS OF INSULATED CABLES (IEC 60228:1978, FIRST SUPPLEMENT 228A:1982 AND AMENDMENT 1:1993, IDT) TESTS ON CABLE OVERSHEATHS WHICH HAVE A SPECIAL PROTECTIVE FUNCTION AND ARE APPLIED BY EXTRUSION ELECTRIC CABLES - CALCULATION OF THE CURRENT RATING - PART 1: CURRENT RATING EQUATIONS (100% LOAD FACTOR) AND CALCULATION OF LOSSES - SECTION 2: SHEATH EDDY CURRENT LOSS FACTORS FOR TWO CIRCUITS IN FLAT FORMATION S 12/5/2015 TC/S/9 agreed to withdraw the MS and direct Y 7/5/2015 The base standard had been withdrawn Y 7/5/2015 The base standard had been withdrawn Y 7/5/2015 The base standard had been withdrawn P 10/9/2015 There is no sales of the standard since its publication in 2010 and the standard is not referred to by the industries in this area. P 10/9/2015 There is no sales of the standard since its publication in 2010 and the standard is not referred to by the industries in this area.
35 MS IEC 60287-2-1:2001 ELECTRIC CABLES - CALCULATION OF THE CURRENT RATING - PART 2: THERMAL RESISTANCE - SECTION 1: CALCULATION OF THERMAL RESISTANCE (IEC 60287-2-1:2000) 36 MS IEC 60287-2-2:2001 ELECTRIC CABLES - CALCULATION OF THE CURRENT RATING - PART 2: THERMAL RESISTANCE - SECTION 2: A METHOD FOR CALCULATING REDUCTION FACTORS FOR GROUPS OF CABLES OF CABLES IN FREE AIR, PROTECTED FROM SOLAR 37 MS IEC 60287-3-2:2003 38 MS IEC 60502-1:1998 39 MS IEC 60502-2:1998 40 MS IEC 60502-4:1998 41 MS IEC 60811-1-1:1997 RADIATION ELECTRIC CABLES - CALCULATION OF THE CURRENT RATING - PART 3: SECTIONS ON OPERATING CONDITIONS - SECTION 2: ECONOMIC OPTIMIZATION OF POWER CABLE SIZE POWER CABLES WITH EXTRUDED INSULATION AND THEIR ACCESSORIES FOR RATED VOLTAGES FROM 1 KV (UM =1.2KV) UP TO 30KV (UM = 36KV) - PART 1: CABLES FOR RATED VOLTAGES OF 1 KV (UM = 1.2 KV) AND 30 KV (UM = 3.6 KV) (IEC 60502-1:1998, IDT) POWER CABLES WITH EXTRUDED INSULATION AND THEIR ACCESSORIES FOR RATED VOLTAGES FROM 1 KV (UM = 1.2 KV) UP TO 30KV (UM =36 KV) - PART 2: CABLES FOR RATED VOLTAGES FROM 6KV (UM7.2KV) UP TO 30KV (UM = 36 KV) (IEC 60502-2:1998, IDT) POWER CABLES WITH EXTRUDED INSULATION AND THEIR ACCESSORIES FOR RATED VOLTAGES FROM 1 KV (UM = 1.2 KV) UP TO 30 KV (UM = 36 KV) PART 4: TEST REQUIREMENTS ON ACCESSORIES FOR CABLES WITH RATED VOLTAGES FROM 6 KV (UM = 7.2 KV) UP TO 30 KV (UM = 36 KV) (IEC 60502-4:1998, IDT) PART 1: METHODS FOR GENERAL APPLICATION - SECTION 1: MEASUREMENT OF THICKNESS AND OVERALL DIMENSIONS - TESTS FOR DETERMINING THE MECHANICAL PROPERTIES (IEC 811-1-1:1993, IDT)
42 MS IEC 60811-1-2:1997 MATERIALS OF ELECTRIC CABLES - PART 1: METHODS FOR GENERAL APPLICATION - SECTION 2: THERMAL AGEING METHODS (IEC811-1-2:1985, IDT) 43 MS IEC 60811-1-3:1997 MATERIALS OF ELECTRIC CABLES - COMMON TEST METHODS - PART 1: GENERAL APPLICATION - SECTION 3: METHODS FOR DETERMINING THE DENSITY - WATER ABSORPTION TESTS - SHRINKAGE 44 MS IEC 60811-1-4:1997 45 MS IEC 60811-2-1:1997 46 MS IEC 60811-3-1:1997 47 MS IEC 60811-3-2:1997 TEST (IEC 811-1-3:1993, IDT) PART 1: METHODS FOR GENERAL APPLICATION - SECTION FOUR: TESTS AT LOW TEMPERATURE (IEC 811-1-4:1985, IDT) PART 2: METHODS SPECIFIC TO ELASTOMERIC COMPOUNDS. SECTION ONE: OZONE RESISTANCE TEST - HOT SET TEST - MINERAL OIL IMMERSION TEST (IEC 811-2-1:1986, IDT) PART 3: METHODS SPECIFIC TO PVC COMPOUNDS. SECTION ONE: PRESSURE TEST AT HIGH TEMPERATURE - TESTS FOR RESISTANCE TO CRACKING (IEC 811-3-1:1985, IDT) PART 3: METHODS SPECIFIC TO PVC COMPOUNDS. SECTION TWO: LOSS OF MASS TEST - THERMAL STABILITY TEST (IEC 811-3-2:1985, IDT)
48 MS IEC 60811-4-1:1997 PART 4: METHODS SPECIFIC TO POLYETHYLENE AND POLYPROPYLENE COMPOUNDS. SECTION ONE: RESISTANCE TO ENVIRONMENTAL STRESS CRACKING - WRAPPING TEST AFTER THERMAL AGEING IN AIR - MEASUREMENT OF THE MELT FLOW INDEX - CARBON BLACK AND/OR MINERAL CONTENT MEASUREMENT IN PE (IEC 811-4- 1:1985, IDT) 49 MS IEC 60811-4-2:1997 PART 4: METHODS SPECIFIC TO POLYETHYLENE AND POLYPROPYLENE COMPOUNDS. SECTION TWO: ELONGATION AT BREAK AFTER PRE-CONDITIONING - WRAPPING TEST AFTER THERMAL AGEING IN AIR - MEASUREMENT OF MASS INCREASE - LONG - TERM STABILITY TEST (APPENDIX A ) - TEST METHOD FOR COPPER - CATALYSED OXIDATIVE DEGRADATION (APPENDIX B) (IEC 50 MS IEC 60811-5-1:1997 51 MS IEC 60885-1:2003 52 MS IEC 60885-2:2003 53 MS IEC 60885-3:2003 811-4-2:1990, IDT) PART 5: METHODS SPECIFIC TO FILLING COMPOUNDS. SECTION ONE: DROP-POINT - SEPARATION OF OIL - LOWER TEMPERATURE BRITTLENESS - TOTAL ACID NUMBER - ABSENCE OF CORROSIVE COMPONENTS - PERMITTIVITY AT 23ºC - D.C. RESISTIVITY AT 23ºC AND 100ºC (IEC 811-5-1:1990, IDT) ELECTRICAL TEST METHODS FOR ELECTRIC CABLES - PART 1: ELECTRICAL TEST FOR CABLES, CORD AND WIRES FOR VOLTAGES UP TO AND INCLUDING 450/750 V (IEC 60885-1:1987, IDT) ELECTRICAL TEST METHODS FOR ELECTRIC CABLES - PART 2: PARTIAL DISCHARGE TESTS (IEC 60885-2:1987, IDT) ELECTRICAL TEST METHODS FOR ELECTRIC CABLES - PART 3: TEST METHODS FOR PARTIAL DISCHARGE MEASUREMENTS ON LENGTHS OF EXTRUDED POWER CABLES (IEC 60885-3:1988, IDT)
54 MS IEC 61000-4-2:2007 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-2: TESTING AND MEASUREMENT TECHNIQUES - ELECTROSTATIC DISCHARGE IMMUNITY TEST (FIRST REVISION) (IEC 61000-4- 2:2001, IDT) 55 MS IEC 60269-3-1:2006 56 MS IEC 60269-4-1:2005 57 MS IEC 61194:2009 58 MS IEC 61646:2010 59 MS IEC 61730-1:2010 60 MS IEC 61730-2:2010 LOW-VOLTAGE FUSES - PART 3-1: SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY UNSKILLED PERSONS (FUSES MAINLY FOR HOUSEHOLD AND SIMILAR APPLICATIONS) - SECTIONS I TO IV: EXAMPLES OF TYPES OF STANDARDIZED FUSES (FIRST REVISION) (IEC 60269-3- 1:2004, IDT) LOW-VOLTAGE FUSES - PART 4-1: SUPPLEMENTARY REQUIREMENTS FOR FUSE-LINKS FOR THE PROTECTION OF SEMICONDUCTOR DEVICES - SECTIONS I TO III: EXAMPLES OF TYPES OF STANDARDIZED FUSE-LINKS (IEC 60269-4-1:2002, IDT) CHARACTERISTIC PARAMETERS OF STAND-ALONE PHOTOVOLTAIC (PV) SYSTEMS (IEC 61194:1992, IDT) THIN-FILM TERRESTRIAL PHOTOVOLTAIC (PV) MODULES - DESIGN QUALIFICATION AND TYPE APPROVAL (FIRST REVISION) (IEC 61646:2008, IDT) PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, IDT) PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 2: REQUIREMENTS FOR TESTING (IEC 61730-2:2004, IDT) E 3/6/2015 WG/E/5-5 agreed to withdraw the MS and direct E 3/6/2015 WG/E/5-5 agreed to withdraw the MS and direct E 3/6/2015 WG/E/8-1 agreed to withdraw the MS and direct E 3/6/2015 WG/E/8-1 agreed to withdraw the MS and direct E 3/6/2015 WG/E/8-1 agreed to withdraw the MS and direct E 3/6/2015 WG/E/8-1 agreed to withdraw the MS and direct