Application Dimensional drawings Suitable for non-corrosive and corrosive gases, vapors and liquids; permissible operating temperature -60 to +550 C. Design Two support rings with replaceable orifice disk form A, B or D (see types of primary differential pressure devices in "Technical description", "Function"); see Ordering data for materials. Graphite gasket with noncorrosive metal foil insert between orifice disk and support ring outlet Overall length 65 mm to DIN 19205 Nominal diameters EN: DN 50 to DN 1000 ASME: 2 inch to 0 inch Nominal pressure EN: PN 6 to PN 100 ASME: class 150 to 600 Sealing face to the mating flanges Plane, sealing face turned, N10/N12 to DIN ISO 1302, for soft gasket (PN 6 to PN 0) Plane, sealing face turned, N8 to DIN ISO 1302, f or grooved gasket to DIN 2697 (PN 63 to PN 100) Plane, RF (raised faced) for version to ASME Tapping sockets For the dimensions of the following tapping sockets (see page /351): With connection thread G½ DIN ISO 228/1, connection dimensions to DIN 19207 form V With threaded connection ½-1 NPT male, for version to ASME with ferrule for pipe Ø 12 mm, S series with welding connection Ø 21.3 mm See "Technical description" and "Function" for position of the tapping sockets. Orifice plate with annular chamber (left); tapping socket with threaded connection, dimensions in mm Tapping socket: Socket length is fixed in accordance with the pressure and nominal diameter (DIN 19 205, Part 2). - Threaded connections of tapping sockets for liquids and gases up to PN 160, for steam up to PN 100, dimensions in mm Versions for steam lines: See "Technical description", "Function" for position of the tapping sockets. /358 Siemens FI 01 2010
SITRANS F flowmeters Nominal diameter acc. to EN DN Inside diameter External diameter d / sealing face: plane, with recess or with groove. PN 6 PN 10 PN 16 PN 25 PN 0 PN 63 PN 100 50 3... 55 96 107 107 107 107 113 119 65 59... 71 116 127 127 127 127 138 1 80 73... 85 132 12 12 12 12 18 15 100 90... 108 152 162 162 168 168 17 180 125 11... 132 182 192 192 19 19 210 217 150 12... 160 207 218 218 22 22 27 257 200 185... 211 262 273 273 28 290 309 32 250 237... 262 317 328 329 30 352 36 391 300 285... 31 373 378 38 00 17 2 58 350 328... 362 23 38 57 7 86 512 00 380... 08 73 89 95 51 56 53 500 77... 51 578 59 617 62 628 600 581... 610 679 695 73 731 700 686... 710 78 810 80 833 800 776... 810 890 917 911 92 900 876... 910 990 1 017 1 011 1 02 1000 976... 1 010 1 090 1 12 1 128 1 15 Orifice plates with annular chambers for installation between EN flanges to EN 1092-1, dimensions in mm and weights DN L E Weight (approx. in kg) PN 6 PN 10... PN 25 PN 0 PN 63... PN 100 PN 6... PN 100 With smallest nominal pressure With largest nominal pressure 50 79 79 79 79 2±0.2 2,5.5 65 96 96 96 96 2±0.2 3. 6. 80 115 115 115 115 ±0.2.3 6.9 100 137 137 137 137 ±0.25.7 8.6 125 16 16 16 16 ±0.25 6.3 12. 150 193 193 193 193 ±0.29 7.0 17.0 200 27 27 27 27 ±0.29 10.3 26.2 250 302 302 302 302 ±0.32 13.1 36.6 300 35 35 35 35 ±0.36 17.3 9.0 350 03 03 03 03 ±0. 25.0 63.0 00 52 52 52 52 ±0. 28.0 73.8 500 553 563 563 6±0. 36.2 65.9 600 659 659 6±0. 2.5 75.6 700 757 762 8±0. 51.8 89.5 800 869 875 8±0. 61.7 109 900 969 975 8±0. 68.3 123 1 000 1 071 1 079 10±0. 7.0 18 Orifice plates with annular chambers for installation between EN flanges to EN 1092-1, dimensions in mm and weights (contd.) Siemens FI 01 2010 /359
Nominal diameter acc. to ASME Nominal diameter External diameter d / sealing face: Plane, RF (raised faced) Class 150 Class 300 Class 600 Class 150 Class 300 Class 600 Class 150... 600 L E Weight (approx. in kg) Orifice plates with annular chambers for installation between ASME flanges to ASME B16.5, dimensions in mm and weights With smallest nominal pressure 2 inch 105 111 111 79 79 79 2±0.2 2.5.5 2½ inch 12 130 130 96 96 96 2±0.2 3. 6. 3 inch 137 19 19 115 115 115 ±0.2.3 6.9 inch 175 181 19 137 137 137 ±0.2.7 8.6 5 inch 197 216 21 16 16 16 ±0.25 6.3 12. 6 inch 222 251 267 193 193 193 ±0.29 7.0 17.0 8 inch 279 308 321 27 27 27 ±0.29 10.3 26.2 10 inch 30 362 00 302 302 302 ±0.32 13.1 36.6 12 inch 10 22 57 35 35 35 ±0.36 17.3 9.0 1 inch 51 86 92 03 03 03 ±0. 25.0 63.0 16 inch 51 50 565 52 52 52 ±0. 28.0 73.8 20 inch 59 597 613 553 563 563 6±0. 36.2 65.9 2 inch 717 775 790 659 659 6±0. 2.5 75.6 With largest nominal pressure /360 Siemens FI 01 2010
SITRANS F flowmeters 7 M E 1 1 1 0 77777 7777 Z 7 M E 1 1 1 0 77777 7777 Z for mounting between flanges Sealing faces to the mating flanges: plane. Nominal diameter acc. to EN DN 50...0 3 DN 65...0 3 DN 80...0 3 DN 100 and PN 0 3 DN 125 and PN 0 3 DN 150 and PN 0 3 DN 200 PN 0 3 DN 250 PN 0 3 DN 300 PN 0 3 1GA 1GE 1GF 1GG 1HA 1HE 1HF 1HG 1JA 1JE 1JF 1JG 2AA 2AC 2AE 2AF 2AG 2BA 2BC 2BE 2BF 2BG 2CA 2CC 2CE 2CF 2CG 2EA 2EC 2ED 2EE 2EF 2EG 2FA 2FB 2FC 2FD 2FE 2FF 2FG 2GA 2GB 2GC 2GD 2GE 2GF 2GG DN 350 PN 0 3 DN 00 PN 0 3 DN 500 PN 0 DN 600 DN 700 DN 800 DN 900 DN 1000 Nominal diameter acc. to ASME 2 inch 2½ inch 3 inch inch 2HA 2HB 2HC 2HD 2HE 2HF 2HG 2JA 2JB 2JC 2JD 2JE 2JF 2KA 2KB 2KC 2KD 2KE 3AA 3AB 3AC 3AD 3BA 3BB 3BC 3BD 3CA 3CB 3CC 3CD 3DA 3DB 3DC 3DD 3EA 3EB 3EC 3ED 5GA 5GB 5GC 5HA 5HB 5HC 5JA 5JB 5JC 6AA 6AB Siemens FI 01 2010 /361
7 M E 1 1 1 0 77777 7777 Z 7 M E 1 1 1 0 77777 7777 Z 5 inch 6 inch 8 inch 10 inch 12 inch 1 inch 16 inch 20 inch 2 inch for non-corrosive media Support rings made of P250GH, Mat.No. 1.060 or P265GH, Mat.No. 1.025; Tappet sockets made of P235G1TH, Mat.No. 1.035; orifice disk made of X 6 CrNiMoTi 17-12-2, Mat.No. 1.571; permissible operating temperature 10 up to +50 C, for tapping socket with ferrule for pipe, 12 mm, S series, max. 200 C 6AC 6BA 6BB 6BC 6CA 6CB 6CC 6EA 6EB 6EC 6FA 6FB 6FC 6GA 6GB 6GC 6HA 6HB 6HC 6JA 6JB 6JC 6KA 6KB 6KC 7AA 7AB 7AC 1 2 Tapping sockets With threaded connection G½; for liquids and gases PN 160, for steam PN 100 - Opposite one another, straight 1 A 1 B - Arranged on one side, 1 C for horizontal pipelines With threaded connection ½-1 NPT male - Opposite one another, straight 1 Q 1 R - Arranged on one side, 1 S for horizontal pipelines With ferrule for pipe Ø 12 mm, S series - Opposite one another, straight 1 J 1 K - Arranged on one side, 1 L for horizontal pipelines With welding connection 21.3 mm; for liquids and gases PN 100 to PN 00 for steam PN 100 - Opposite one another, straight 1 D 1 E - Arranged on one side, 1 F for horizontal pipelines Shape of orifice disk aperture (see figure "Shapes of orifice disk aperture") For flow in one direction - Orifice plate form A A - Quarter-circle nozzle form B B For flow in both directions - Cylindrical orifice plate form D D Manufactured according to pressure equipment directive (see "Questionnaire" (page /356)) Without² ) 0 According to Article 3, 1 Paragraph 3 According to category 1 2 According to category 2 3 According to category 3 For corrosive media Support rings, tapping socket and orifice disk made of X 6 CrNiMoTi 17-12-2, Mat.No. 1.571; permissible temperature 60 to +550 C, for tapping socket with ferrule for pipe, 12 mm, S series, max. 00 C 1 /362 Siemens FI 01 2010
SITRANS F flowmeters 7 M E 1 1 1 0 77777 7777 Z Further designs Order code 1) Add "-Z" to and specify Order code(s) and plain text. Calculation of orifice disk A11 aperture Enclose a calculation sheet "Questionnaire for calculation of a primary differential pressure device according to DIN EN ISO 5167" with the order! Orifice plate without calculation Y01 Specify in plain text: Diameter of orifice disk aperture d =... mm Internal diameter of pipe D =... mm Radius of quarter-circle nozzle r =... mm Material certificate C01 Acceptance test certificate to EN 1020-3.1 Orifice plate degreased A12 for oxygen measurements Note: Cleaned and foil-packed. When using, note that the orifice plate must be completely degreased when fitted in the pipeline. Orifice disk including gasket On request Other materials On request Additional nominal diameters On request and nominal pressure stages according to EN and ASME Cold water pressure test On request 1.5 x PN, acceptance test certificate to EN 1020 Flushing rings On request Support rings made of 1.7335 On request Sealing face of orifice plate On request with recess or groove 1) Order codes additive, any sequence. 2) Option only available outside Europe (manufactured according to Article 3, Paragraph 3 of the pressure equipment directive, without CE marking). Note on ordering Enclose a filled-out calculation sheet "Questionnaire for calculation of a primary differential pressure device according to DIN EN ISO 5167" with the order (necessary for device selection)! scope of delivery Two support rings with tapping sockets, one orifice disk, one gasket between orifice disk and support ring. Graphite (99.85 %) flat gasket with foil insert (1.01, 0.1 mm). Application for liquids, steam, gases, liquid gases, acids, hydrocarbons, oils and oil products. Accessories See "SITRANS P measuring instruments for pressure". Siemens FI 01 2010 /363
Application Suitable for non-corrosive and corrosive gases, vapors and liquids; permissible operating temperature -60 to +570 C Design One-piece orifice plate, orifice disk form A, B or D (see types of primary differential pressure devices in "Technical description", "Function"); see Ordering data for materials. Overall length 0 mm to DIN 19205 Nominal diameters EN: DN 50 to DN 500 ASME: 2 inch to 20 inch Nominal pressure EN: PN 6 to PN 315 ASME: class 150 to 2500 Sealing face to the mating flanges Plane, sealing face turned, N10/N12 to DIN ISO 1302, for soft gasket (PN 6 to PN 0) Plane, sealing face turned, N8 to DIN ISO 1302, for grooved gasket to DIN 2697 (PN 63 to PN 00) Plane, RF (raised faced) for versions to ASME Tapping sockets With connection thread G½ DIN ISO 228/1, for connection dimensions to DIN 19207 form V(see page /351) With threaded connection ½-1 NPT male, for version to ASME With ferrule for pipe Ø 12 mm, S series With welding connection Ø 21.3 mm Connection size The connection size depends on the operating pressure, the temperature of the medium (DIN 19 207 and 19 211) and the medium, e.g. For liquids and gases, - up to PN 160: Thread G½ or welding connection Ø 21.3 mm - from PN 6 and PN 00: Welding connection Ø 21.3 mm - > PN 00: Welding connection Ø 2 mm For steam - up to PN 100: Thread G½ or welding connection Ø 21.3 mm - from PN 6: Welding connection Ø 2 mm See "Technical description" and "Function" for position of the tapping sockets. /36 Siemens FI 01 2010
SITRANS F flowmeters Dimensional drawings Tapping socket: Socket length is fixed in accordance with the pressure and nominal diameter (DIN 19 205, Part 2), dimensions in mm - Threaded connections of tapping sockets for liquids and gases up to PN 160, for steam up to PN 100, Versions for steam lines: See "Technical description", "Function" for position of the tapping sockets. Nominal diameter acc. to EN DN Inside diameter External diameter d / sealing face: plane, with recess or with groove. Orifice plates with single tappings for installation between EN flanges to EN 1092-1, dimensions in mm and weights Nominal diameter acc. to ASME Orifice plates with single tappings for installation between ASME flanges to ASME B 16.5, dimensions in mm and weights Weight (approx. in kg) PN 6 PN 10 PN 16 PN 25 PN 0 PN 63 PN 100 PN 160 PN 250 PN 315 With smallest nom. pressure 50 5... 55 96 107 107 107 107 113 119 119 12 13 1.6.0 65 61... 71 116 127 127 127 127 138 1 1 15 170 2.2 6.3 80 77... 85 132 12 12 12 12 18 15 15 170 190 2.9 7.8 100 9... 108 152 162 162 168 168 17 180 180 202 229 3.2 11.5 125 117... 132 182 192 192 19 19 210 217 217 22 27.3 15.9 150 1... 160 207 218 218 22 22 27 257 257 28 311.7 20.6 200 188... 211 262 273 273 28 290 309 32 32 358 398 7.0 33.7 250 20... 262 317 328 329 30 352 36 391 388 2 88 9.0 50.6 300 292... 31 373 378 38 00 17 2 58 58 538 12.3 37.3 350 331... 362 23 38 57 7 86 512 17.7.6 00 383... 08 73 89 95 51 56 53 19.8 3.1 500 80... 51 578 59 617 62 628 25.6 6.6 Nominal diameter With largest nom. pressure External diameter d / sealing face: plane, with recess Weight (approx. in kg) or with groove. Class 150 Class 300 Class 600 With smallest nominal pressure With largest nominal pressure 2 inch 105 111 111 1.6.0 2½ inch 12 130 130 2.2 6.3 3 inch 137 19 19 2.9 7.8 inch 175 181 19 3.2 11.5 5 inch 197 216 21.3 15.9 6 inch 222 251 267.7 20.6 8 inch 279 308 321 7.0 33.7 10 inch 30 362 00 9.0 50.6 12 inch 10 22 57 12.3 37.3 1 inch 51 86 92 17.7.6 16 inch 51 50 565 19.8 3.1 20 inch 59 597 613 25.6 6.6 Siemens FI 01 2010 /365
7 M E 1 1 2 0 77777 7777 Z 7 M E 1 1 2 0 77777 7777 Z for mounting between flanges Sealing faces to the mating flanges: plane. Nominal diameter acc. to EN DN 50...0 3 and PN 160 DN 65...0 3 and PN 160 DN 80...0 3 and PN 160 DN 100 and PN 0 3 and PN 160 DN 125 and PN 0 3 and PN 160 DN 150 and PN 0 3 and PN 160 DN 200 PN 0 PN 63 and PN 160 1GA 1GE 1GF 1GH 1GJ 1GK 1HA 1HE 1HF 1HH 1HJ 1HK 1JA 1JE 1JF 1JH 1JJ 1JK 2AA 2AC 2AE 2AF 2AH 2AJ 2AK 2BA 2BC 2BE 2BF 2BH 2BJ 2BK 2CA 2CC 2CE 2CF 2CH 2CJ 2CK 2EA 2EC 2ED 2EE 2EF 2EH 2EJ 2EK DN 250 PN 0 PN 63 and PN 160 DN 300 PN 16 PN 0 PN 63 and PN 160 DN 350 PN 16 PN 0 PN 63 DN 00 PN 16 PN 0 PN 63 DN 500 PN 16 PN 0 Nominal diameter acc. to ASME 2 inch 2½ inch 3 inch inch 5 inch 2FA 2FC 2FD 2FE 2FF 2FH 2FJ 2FK 2GA 2GB 2GC 2GD 2GE 2GF 2GH 2HA 2HB 2HC 2HD 2HE 2HF 2HG 2JA 2JB 2JC 2JD 2JE 2JF 2KA 2KB 2KC 2KD 2KE 5GA 5GB 5GC 5HA 5HB 5HC 5JA 5JB 5JC 6AA 6AB 6AC 6BA 6BB 6BC /366 Siemens FI 01 2010
SITRANS F flowmeters 7 M E 1 1 2 0 77777 7777 Z 7 M E 1 1 2 0 77777 7777 Z 6 inch 8 inch 10 inch 12 inch 1 inch 16 inch 20 inch for non-corrosive media Orifice plate and tapping socket made of 13 CrMo -5, Mat.No. 1.7335; metering edge with X 5 CrNiMoNb 19 12, Mat.No. 1.576, deposition welded; permissible working pressure 10 to +570 C, for tapping socket with ferrule for pipe, 12 mm, S series, max. 200 C for corrosive media Orifice plate and tapping socket made of X 6 CrNiMoTi 17-12-2, Mat. No. 1.571; permissible operating temperature -200 to +550 C, for tapping socket with ferrule for pipe, 12 mm, S series, max. 00 C 6CA 6CB 6CC 6EA 6EB 6EC 6FA 6FB 6FC 6GA 6GB 6GC 6HA 6HB 6HC 6JA 6JB 6JC 6KA 6KB 6KC 2 2 2 Tapping sockets With threaded connection G½; for liquids and gases PN 160, for steam PN 100 - Opposite one another, straight 1 A 1 B - Any arrangement of tapping 1 G sockets (specify angle in plain text) With threaded connection ½-1 NPT male - Opposite one another, straight 1 Q 1 R - Any arrangement of tapping 1 T sockets (specify angle in plain text -Z Y02) With ferrule for pipe Ø 12 mm, S series, max. 200 C permissible - Opposite one another, straight 1 J 1 K - Any arrangement of tapping 1 M sockets (specify angle in plain text -Z Y02) With welding connection 21.3 mm; for liquids and gases PN 100... 00, for steam PN 100 or 2 mm; for liquids and gases over PN 00, for steam over PN 100 - Opposite one another, straight 1 D 1 E - Any arrangement of tapping 1 H sockets (specify angle in plain text) Shape of orifice disk aperture (see figure "Shapes of orifice disk aperture") For flow in one direction - Orifice plate form A A - Quarter-circle nozzle form B B For flow in both directions - Cylindrical orifice plate form D D Manufactured according to pressure equipment directive (see "Questionnaire" (page /356)) Without² ) 0 According to Article 3, 1 Paragraph 3 According to category 1 2 According to category 2 3 According to category 3 Siemens FI 01 2010 /367
7 M E 1 1 2 0 77777 7777 Z Further designs Order code 1) Add "-Z" to and specify Order code(s) and plain text. Calculation of orifice disk A11 aperture Add calculation sheet "Questionnaire for calculation of a primary differential pressure device acc. to DIN EN ISO 5167" to the order! Orifice plate without calculation Y01 Specify in plain text: Diameter of orifice disk aperture d =... mm Internal diameter of pipe D =... mm Radius of quarter-circle nozzle r =... mm Material certificate C01 Acceptance test certificate to EN 1020-3.1 Orifice plate degreased A12 for oxygen measurements Note: Cleaned and foil-packed. When using, note that the orifice plate must be completely degreased when fitted in the pipeline. Angle between tapping sockets Y02 (specify in plain text: Angle between the tapping sockets... ) Other materials On request Additional nominal diameters On request and nominal pressure stages according to EN and ASME Overall length 65 mm On request (required for tapping sockets arranged on one side) Cold water pressure test On request 1.5 x PN, acceptance test certificate to EN 1020 Flushing rings On request Sealing face of orifice plate On request with recess or groove Note on ordering Enclose a filled-out calculation sheet "Questionnaire for calculation of a primary differential pressure device according to DIN EN ISO 5167" with the order (necessary for device selection)! Scope of delivery: One-part orifice plate with tapping sockets Accessories: See "SITRANS P measuring instruments for pressure". 1) Order codes additive, any sequence. 2) Option only available outside Europe (manufactured according to Article 3, Paragraph 3 of the pressure equipment directive, without CE marking). /368 Siemens FI 01 2010