Exten-A-Kut II Rotary Ditch and Bank Mower Rev 0- PARTS MANUAL Part No. 099P ALAMO INDUSTRIAL 0 E. Walnut Seguin, Texas 78 80-7-99 An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800--8) to obtain a Free copy before operating the equipment. 0 Alamo Group, Inc.
TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness. Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart. Bolt tightness should be completed with and checked with a suitable torque wrench. Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual. Loose bolts on a frame or in a casting may be a result of: Vibration from the mower due to imbalance of the mower blades Pulled threads due to over tightening Distortion of the hole due to under tightening during installation Bolts broken or sheared in the mounting structure or tractor may be the result of: Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating surface Distortion of the bolt due to over-tightening Under tightening of the bolts Check the bolt torque during installation and prior to delivery with a suitable torque wrench.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 0 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
CHANGE PAGES Date of Change Page Number 0-0-0 (EXAMPLE ONLY: ECN##### - chg pages 7,, 7) 0-0-0 document release date 08--0 chg pg 9 0--0 chg pgs 7-8zz Change Pages -
CHANGE PAGES The following is a listing of pages that have been changed since the latest publication date for the overall document. Change Pages -
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.. The Manufacturer reserves the right to substitute parts where applicable.. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.. The Manufacturer reserves the right to change prices without prior notice. Note: Please refer to The Safety Section in the front of this Manual for the proper part number when ordering replacement safety decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 0 E. Walnut Seguin, Texas 78 80-79-80 0 Alamo Group Inc. Parts Section
PART NAME INDEX BLADE BAR ASY... BLADE PAN ASY... CHAIN GUARDS - FRONT & REAR - DOUBLE... 7 CHAIN GUARDS - FRONT & REAR - SINGLE... 8 DEFLECTORS - FRONT & REAR... 9 HYD CYL ASY - EXTENSION - PN 0700A... 0 HYD CYL ASY - TILT - PN 007997A... HYD HOSE SCHEMATIC... HYD MOTOR ASY... HYD MOTOR PARTS... 7 HYD TANK ASY - PN 007709... 9 MAINFRAME ASY... MAINFRAME BOOM ASY... MOWER HEAD ASY... PUMP & SPEED INCREASER - INSTALLATION... 7 PUMP & SPEED INCREASER ASY (0 & 000 RPM)... 8 PUMP ASY - PN 0989... 9 SIDE CASTER WHEELS (INDIANA OPTION)... SPEED INCREASER ASY (000 RPM) PN 0977P... SPINDLE & HOUSING ASY - PN 0077... TAIL WHEEL ASY - PN 09 (OPTIONAL)... VALVE - FENDER MOUNT... 8 VALVE KIT ASY... 9 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
BLADE BAR ASY 00778 CARRIER ASSY BLADE BAR 0000700 HEXB /8 NC -/ 9 WASHER, STRUCTURAL 8, BLADE JRC0 LOCKNUT TLM NF PL 80 HUB,BLADE 00900 LOCKNUT /8 NC PLC 7 00777 SPACER DISK 8 00777 SET,MATCHED BLADE-DB0 9 0077 BAR,BLADE UNFORMED 0 007077 WASHER,/8 HARDENED 007879 WASHER,-9/ SQ HOLE X OD 807 KEY,ROUND END PL 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
BLADE PAN ASY 0077 BLADE PAN 00777 BLADE 8 BLADE 007879 BLADE WASHER 9 WASHER JRC0 LOCKNUT 7 0077 BLADE BAR, UNFORMED 8 00770 BLADE BAR, FORMED 9 80 HUB 0 D00 NUT 000000 COTTER PIN 0077 007077 WASHER 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
BLADE PAN ASY Continued... 00900 NUT, TOPLOCK /8 NC PLC 0000700 C000 WASHER 807 KEY,ROUND END 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
CHAIN GUARDS - FRONT & REAR - DOUBLE 0000800 LOCKNUT TLM / NC PLC 0000700 0 FLATWASHER 00788 0077 RIGHT SIDE SHIELD 0077 CHAINGUARD MOUNTING PLATE A 007778 DOUBLE CHAIN GUARD ASY. 0077 CHAINGUARD BRACKET 7 007778 LEFT SIDE SHIELD 8 000700 9 007 CHAIN 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -7
CHAIN GUARDS - FRONT & REAR - SINGLE 0000800 LOCKNUT TLM / NC PLC 0000700 0 FLATWASHER 00788 0077 RIGHT SIDE SHIELD 0077 CHAINGUARD MOUNTING PLATE 0077 CHAINGUARD BRACKET 7 007778 LEFT SIDE SHIELD 8 000700 9 007777 CHAIN GUARD ASY. 0 007 8 CHAIN 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -8
DEFLECTORS - FRONT & REAR 0000800 LOCKNUT TLM / NC PLC 0000700 0 FLATWASHER 00788 0077 RIGHT SIDE SHIELD 0077 DEFLECTOR MOUNTING PLATE 007778 LEFT SIDE SHIELD 7 000700 8 007778 STRAP 9 007778 RUBBER PANEL 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -9
HYD CYL ASY - EXTENSION - PN 0700A 097909 BARREL WLD`MT 09790 CYLINDER HEAD, GLAND 09 PISTON 07800 RETAINING RING 0979 ROD 070 NUT 7 0978 - *SEAL KIT ( S 8THRU ) 8 *SEAL KIT PISTON SEAL 9 *SEAL KIT GLAND STATIC SEAL 0 *SEAL KIT BACK-UP RING ( ROD ) *SEAL KIT BACK-UP RING ( PISTON ) *SEAL KIT ROD WIPER *SEAL KIT ROD STATIC SEAL *SEAL KIT ROD SEAL 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -0
HYD CYL ASY - TILT - PN 007997A 78 CLEVIS CAP 77 ROD CAP 00777 PISTON 007778 ROD 007779 TUBE 00777 TIE ROD 9 *SEAL KIT END CAP O-RING 0 *SEAL KIT ROD WIPER SEAL *SEAL KIT ROD DUST SEAL *SEAL KIT PISTON SEAL *SEAL KIT PISTON WEAR RING *SEAL KIT END CAP - BACKUP WASHERS 077 NYLON THREAD PROTECTER 970 ROD CLEVIS 7 007770 SET SCREW 8 00HC 8 TIE ROD NUT 9 JRC0 PISTON NUT 0 97 PORT PLUG 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
HYD CYL ASY - TILT - PN 007997A Continued... 7 BREATHER 00777 *SEAL KIT ( S 9 THRU ) 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
HYD HOSE SCHEMATIC 0970 HOSE - SUCTION 0987 HOSE - MANIFOLD TO TANK 0997 HOSE - BULKHEAD TO FILTER 0970 HOSE - PUMP TO MANIFOLD 097 HOSE - TRACTOR TO BULKHEAD 007098 ELBOW - 90 DEG. 7 0800 RESTRICTOR VALVE 8 0979 STRAIGHT ADAPTER 9 09 HOSE - TRACTOR TO EXTENSION CYL. 0 09 HOSE - TRACTOR TO EXTENSION CYL. 0000 ELBOW ADAPTER 0700 EXTENSION CYL. 098 HOSE - BULKHEAD TO TILT CYL. 0700 STRAIGHT ADAPTER 007997A TILT CYL. 007 BULKHEAD FITTING 7 0700 BULKHEAD FITTING 8 0970 HOSE - MOTOR RETURN 9 0078 HOSE - PRESSURE TO MOTOR 0 0077 ADAPTER 90 DEG. 00000 HOSE BIB 09900 ADAPTER 90 DEG. 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
HYD HOSE SCHEMATIC Continued... 087000 MANIFOLD 097 STRAIGHT ADAPTER 00707 STRAIGHT ADAPTER 00779 RELIEF VALVE 7 097 HOSE - MANIFOLD TO BULKHEAD 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
HYD MOTOR ASY 09907 MOTOR 0078 FLANGE FITTING OUTLET 00790 * SPLIT FLANGE SET 087700 FLANGE KIT 09700 ELBOW 0700 REDUCER 7 097 ELBOW 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
THIS PAGE INTENTIONALLY LEFT BLANK 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
HYD MOTOR PARTS 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -7
HYD MOTOR PARTS Continued... * 097997 SNAP RING * 0980 "O" RING * 099 SEAL RETAINER * 097999 SEAL 0997 FLANGE- MOTOR MTG 0990 PLUG 7* 099 CHECK ASY. 8* 097997 SEAL END 9* 097997 THRUST PLATE 0 097 GEAR SET * 097997 SQUARE SEAL 09799 DOWEL PIN 0998 GEAR HOUSING 0997 PORTING FLANGE, W/ BUSHING 0997 WASHER 0998 7* --------- SIDE SEAL ( NOT SHOWN ) 8 099 KEY-. X. X. LONG (NOT SHOWN) ----- 0999 KIT, SEAL, HYD MOTOR 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -8
HYD TANK ASY - PN 007709 00777 TANK WLD`MT 00900 FILLER TUBE ASY. 09 STRAINER - SUCTION 00000 098 WASHER 090 COVER PLATE 7 099 GASKET 8 009700 SIGHT GUAGE 9 09780 - FILTER ASY. 09780 - FILTER ELEMENT 0 0077 - REDUCER BUSHING 00707 - STRAIGHT ADAPTER 00707 PIPE PLUG 099 PLUG 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -9
HYD TANK ASY - PN 007709 Continued... 00000 HOSE BIB 00900 FILLER CAP 09790 FILLER CAP WLD`MT 7 0700 SCREW 8 800 LOCKWASHER 9 700 NUT 0 00788 0000700 FLATWASHER 0000800 LOCKNUT TLM / NC PLC 0970 - ADAPTER TEE 00000 HOSE BIB 0988 SHUT OFF VALVE 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -0
MAINFRAME ASY 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
MAINFRAME ASY Continued... 00777 OIL TANK ASY. 00770 MAIN FRAME WLD`MT 0078 GREASE FITTING 090 SAFETY CLIP PIN 007 STABILIZER WLD`MT 0000800 LOCKNUT TLM / NC PLC 7 00788 8 9 HITCH PIN CAT II & CAT III 9 9 LYNCH PIN 0 9 HITCH PIN BUSHING 09897 0000700 FLATWASHER 00000 LOCKNUT 07800 BUSHING 0007 000000 LOCKWASHER 7 00707 STRAIGHT ADAPTER 8 0909 CLAMP 9 00779 HOSE CLAMP WLD`MT 0 000800 LOCKNUT 00779 CARTRIDGE RELIEF 097 STRAIGHT HYD. ADAPTER 087000 MANIFOLD BLOCK 0009900 098 ADAPTER ELBOW 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
MAINFRAME BOOM ASY 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
MAINFRAME BOOM ASY Continued... 09 HOSE 00080 HOSE 007709 BOOM WLD`MT 8 CYLINDER PIN ( 0 ) 707B CYLINDER PIN ( 000 ) 007997A CYLINDER 8 CYLINDER PIN 7 000000 COTTER PIN 8 09880 HYD. ADAPTER 9 098 COUNTER SINK SCREW 0 099 RUBBER BUMPER 07000 EXTENSION CYLINDER 0700 PIN WLD`MT 089000 HOSE 0800 FLATWASHER 000000 GREASE FITTING 099 CAP 7 097 HOSE ADAPTER 8 0700 ADAPTER 9 707B HAIR PIN 0 007098 ELBOW 0979 ADAPTER 09809 CYLINDER PIN WLD`MT 0800 CHECK VALVE 00090 NUT 00779 LEFT LINK 090 LIFT PIN WLD`MT 7 000900 8 000800 LOCKNUT 9 00779 CONNECTING LINK WLD`MT 0 097 SPACER 00779 CONNECTING BAR LINK 0D BUSHING 00779 TRANSPORT BAR 7078 HAIR PIN CLIP 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
MOWER HEAD ASY 09907 HYDRAULIC MOTOR 0090800 ELBOW 000900 LOCKWASHER 089000 70 COVER PLATE F80 WING NUT 7 0077 SPINDLE 8 0070 GASKET 9 00708 0 007077 8 WASHER 00900 NUT,TOPLOCK /8 NC PLC 0909 CLAMP 099 PIN 000900 00800 LOCKNUT 099 BUSHING 7 00778 SKID SHOE, (LH & RH SIDE SAME PART NO.) 8 A PLOW, /8"-NC X -/" 9 00000 FLATWASHER, /8" PL STD 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
MOWER HEAD ASY Continued... 0 000800 LOCKNUT, TOPLOCK /8"-NC PLB 0907 TILT BUSHING TUBE, " LONG 090 TILT BUSHING TUBE, " LONG D00 NUT, HEX SLOTTED -/"-NF PL (BLADE CARRIER RETAINING NUT - NOT SHOWN) 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
PUMP & SPEED INCREASER - INSTALLATION 0979 PUMP ASY. W/ FITTINGS 09897 HEX HEAD, CAP SCREW 000000 LOCKWASHER 09988 SPEED INCREASER - 0 RPM 0000800 LOCKNUT TLM / NC PLC 0970 SUCTION HOSE 7 0970 HOSE 8 0000 HOSE CLAMP 9 0070 HEX HEAD, CAP SCREW 0 00000 HEX HEAD, CAP SCREW 00000 LOCKNUT 0999 SPEED CHANGER PLATE 0700 MOTOR BAR 0997 LINK SPACER, TUBE 0997 HEX HEAD, CAP SCREW 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -7
PUMP & SPEED INCREASER ASY (0 & 000 RPM) 09988 SPEED INCREASER - 0 RPM 00780* SPEED INCREASER - 000 RPM 0989 PUMP 089800 STREET ELBOW 0000 HOSE BIB 09900 ELBOW 0999 MOUNT PLATE 7 09897 8 00900 LOCKWASHER 9 00000 WASHER 0 0070 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -8
PUMP ASY - PN 0989 09799 GEAR PLATE 09979 DRIVE GEAR 09799 IDLE GEAR 099797 CAPSCREW 09797 FLANGE 09798 COVER PLATE 7 09797 SNAP RING 8 09798 PRESSURE PLATE 9 09980 PLUG 0 09797 BACK-UP RING 097977 O-RING 09980 O-RING 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -9
PUMP ASY - PN 0989 Continued... 097978 O-RING 09798 8 DOWELS ( NOT SHOWN ) 09797 SEAL 0999 KIT, SEAL,.87 PUMP 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -0
SIDE CASTER WHEELS (INDIANA OPTION) 00000 WHEEL 000700 AXLE 00000 LOCKNUT 0077 WHEEL SPACER 007787 WHEEL BRKT. - RH 00770 WHEEL BRKT. - LH 7 00788 8 0000700 FLATWASHER 9 000000 LOCKWASHER 0 00790 0000800 LOCKNUT TLM / NC PLC 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
THIS PAGE INTENTIONALLY LEFT BLANK 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
SPEED INCREASER ASY (000 RPM) PN 0977P 0977P - SPEED INCREASER, : RATIO 09777 OIL BREATHER PLUG 097778 GASKET ( OIL PLUGS ) 097770 8 SOCKET CAPSCREW 09777 OIL LEVEL PLUG 097777 OIL DRAIN PLUG 097779 PEG 7 0998 BEARING 8 097777 CAP 9 097788 PINION GEAR 0 09777 SEALING RING 09777 GASKET HOUSING 09777 COVER HOUSING 097778 8 NUT 009700 BEARING 0977770 SNAP RING 097789 RING GEAR 8 007 BEARING 9 097779 SEALING RING 097777 PTO SHAFT, " - /8" FEMALE 7 09777 MAIN HOUSING 8 0980 PUMP FLANGE ( NOT SHOWN ) 9 0980 SPLINE COUPLER ( NOT SHOWN ) 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
SPINDLE & HOUSING ASY - PN 0077 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
SPINDLE & HOUSING ASY - PN 0077 Continued... 0077 HOUSING 00770 SPINDLE 00787 BEARING CUP 808 BEARING CONE 800 OIL SEAL 0078 BEARING CUP & CONE 7 099 LOCKWASHER 8 0900 SPINDLE BEARING LOCKNUT 9 09908 RELIEF FITTING 0 00000 PLUG 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
TAIL WHEEL ASY - PN 09 (OPTIONAL) 007870 TAIL WHEEL TUBE 0079 COLLAR 0079 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -
TAIL WHEEL ASY - PN 09 (OPTIONAL) Continued... 007907 NUT 00797 CASTER FORK WLD`MT 000 7 0077 AXLE HUB 8 08700 BEARING CUP & CONE ASY. 9 00000 TIRE & RIM 0 00900 NUT,TOPLOCK /8 NC PLC 000000 LOCKWASHER 00770 GREASE FITTING 00000 SEAL 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -7
VALVE - FENDER MOUNT 00000 FLATWASHER 0000 LOCKWASHER 00090 NUT 00787 LONG SPACER BUSHING 08800 VALVE MOUNT PLATE 08800 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -8
VALVE KIT ASY 08090 VALVE - SPOOL 08090 VALVE CLOSED CENTER* 00708 COUPLER 0077800 REDUCER 007 ELBOW 08800 HOSE 007 - HANDLE ASY. KIT 7 0999 HOSE 0000 - HOSE KIT - VALVE TO TRACTOR 8 00900 ELBOW 9 0000 HOSE 099P - Exten-A-Kut II (0-0)_0-0 Alamo Group Inc. Parts Section -9
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (98. Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER. Provide a Roll-Over-Protective Structure that meets the requirements of this standard.. Provide seat belts that meet the requirements of this paragraph of this standard and SAE JC.. Ensure that each employee uses such seat belt while the tractor is moving.. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR. Securely fasten seat belt if the tractor has a ROPS.. Where possible, avoid operating the tractor near ditches, embankments, and holes.. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.. Stay off slopes too steep for safe operation.. Watch where you are going, especially at row ends, on roads, and around trees.. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
ALAMO INDUSTRIAL Limited Warranty. Limited Warranties.0. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( purchaser ) and warrants for six months to the original commercial or industrial purchaser ( purchaser ) that the goods purchased are free from defects in material or workmanship..0. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship..0. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your operator s manual..0. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf of manufacturer.. Remedies And Procedures.0. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 0 days of purchase..0. Purchaser claims must be made in writing to the authorized dealer ( dealer ) from whom purchaser purchased the goods or an approved authorized dealer ( dealer ) within 0 days after purchaser learns of the facts on which the claim is based..0. Purchaser is responsible for returning the goods in question to the dealer..0. If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, manufacturer will: (A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer..0. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory.. Limitation Of Liability.0. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not limited to, merchantability and fitness for a particular purpose..0. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods..0. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods..0. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two () years after the cause of action has occurred.. Miscellaneous.0. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas..0. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term..0. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein..0. Applicable law may provide rights and benefits to purchaser in addition to those provided herein. Keep for your records Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Alamo Industrial Implement Model Serial Number Date Purchased Dealer Attention: Read your operator s manual ALAMO INDUSTRIAL 0 E. Walnut Seguin, Texas 78 80-79-80
0 E. Walnut St. Seguin, Texas 78 Sales and Marketing Tel 800.88.7 Fax 80.79.08 support@alamo-industrial.com Warranty Registration/Claims www.alamoparts.com Return Authorizations Online Part Orders Techical Information www.alamoparts.com Tel 800..8 Fax 800.. www.alamo-industrial.com Exten-A-Kut II (PUB 0-) P/N 099P