Electromechanical Door Operators and Closers Door Closers Lockwood Product Catalogue Module (Version 1.) 4.35
0 Electromechanical Door Operator General Information The Lockwood 0 Swing Door Operator is an electro-hydraulic operator designed for a wide variety of applications. It is suitable for almost all types of external and internal swing doors and has been developed to cope with tough conditions. The operator can be mounted on either side of the door for pull or push action and is suitable for single or double doors fitted with butt hinges or pivots. Suitable for disabled access, nursing homes and hospital corridors - where the requirements are for silence, flexible operation and reliability - as it is for department stores, banks, hotels, etc. Opening When an opening impulse is received by the control unit, the motor starts and the hydraulic unit rotates the drive shaft and arm system (door) with high speed towards the open position. Before reaching the fully open position, the speed is reduced to low speed. The door stops, and the motor rotation ceases when the selected door opening angle is reached. This open position is held by the hydraulic valve. Closing The spring closing starts when the hold-open time has run out. Before reaching the fully closed position, the speed is reduced to low speed, which will be kept until the door is completely closed. The door is held closed by spring power. to overcome the resistance of a striking plate, the lock kick can be adjusted to required level. FIRE RATED Lockwood Swing Door Operators have been successfully tested on fire door assemblies in accordance with Australian Standard AS1905.1:1997 fire resistant doorsets. Ordering Information Product Description Swing Door Operator (PUSH SIDE) Swing Door Operator (PUSH SIDE) 0SSIL 0PSIL Accessories Telescopic 110 35 Reveal (PUSH SIDE) 0-173005 Telescopic 35 360 Reveal (PUSH SIDE) 0-173004 Joint for Telescopic 35 485 Reveal (PUSH SIDE) 0-173191 Doorstop Push 0-100147 Spacer for Door Fitting 0-1734BK Push and Go Function 0-65514 Lock Kick To overcome the resistance of a striker plate, door seals the lock kick can be adjusted to the required level of resistance. This will ensure that the lock bolt will securely engage into the striker plate. Door Specification Max door weight 50kgs Max door width 1600 Access controlled locking (Pull side reduces power by 30%) Maximum opening angle 10. 4.36 Lockwood Product Catalogue Module (Version 1.)
0 Electromechanical Door Operator Mounting Instruction Guide X = Shaft Extension C L C L X = 17 / 37 / 67 100 17 364 100 13 50 X = 46 / 66 / 96 17 364 13 3 50 45 109 58 C L C L Push Side Pull Side Pull Side Push Side 110 110 45 Y 13 Min. 5 3 110 13 110 Y = Shaft Extension 48 0 68 0 98 50 118 70 A 38 Min. 31 38 A 98 Technical Information Electrical Door leaf width Recoended door weight 30V AC mains power, 50 Hz fuse10 A Maximum door width 1600 Maximum door weight 50 kg Door opening angle Maximum opening angle - 10 Closing power EN Size 3 to 6 Specification Statement This Door Operator must have an electro-hydraulic motor with a capacity to push or pull doors up to 50kg in weight. The operator can be mounted on either side of the door for pull or push action and should be suitable for single or double doors fitted with butt hinges or pivots. The operator should have inputs for various electronic keypad controllers and motion sensors. Environment Dimensions Operational temperature range: -15 c to + 50c 110 (H) x 110 (D) x 716 (L) Door Closers For product availability please refer to the current price list, contact customer service or your local sales office. Lockwood Product Catalogue Module (Version 1.) 4.37
Pushing arm system, where the operator is installed on the wall on the opposite side of the door swing. Door opening angle adjustable up Electromechanical Door Operators 0 Electromechanical Door Operator 0 Series Swing Door Operator 0 Series Swing Door Operator to 10. Swing arm operator package comes with silver cover and black push arm. 0PSIL Pushing Pulling Pushing arm system, where the operator is Pushing installed on the wall on the opposite side of the Pushing arm system, where the operator is Pushing door swing. installed arm Door on the system, opening wall on where angle the opposite the adjustable operator up side of the is installed to 10. door swing. on Swing the arm Door wall operator opening on the package angle opposite comes adjustable side upof the with silver cover and black push arm. door to 10. swing. Swing Door arm opening operator angle package adjustable comes up to with 10. silver Swing cover arm and operator black push package arm. comes with silver cover and black push arm. Part 0PSIL Number 0SSIL Part 0PSIL Number 0PSIL Pulling arm system, where the operator is installed on the wall on the same side as the door swing. Door opening angle adjustable up to 10. Swing arm operator package comes with silver cover and black pull arm. 40% Power loss. Pulling Pulling Pulling arm system, where the operator is Pulling arm system, where the operator is installed on the wall on the same side as the installed Pulling arm on the system, wall where on the same operator side is as the door swing. Door opening angle adjustable up door installed swing. on Door the wall opening on the same angle side adjustable as the up to 10. Swing arm operator package comes to door swing. Door opening angle adjustable up with 10. silver Swing cover arm and operator black pull package arm. comes with to 10. Swing arm operator package comes 40% silver Power cover loss. and black pull arm. 40% with Power silver cover loss. and black pull arm. 40% Power loss. Part 0SSIL Number 0SSIL 0SSIL 4 Push and go function add. 0-655614 Controls Controls max. 10 max. 10 Pulling Pulling arm system, where the operator is installed on the wall on the same side as the door swing. Door opening angle adjustable up to 10. Swing arm operator package comes with silver cover and black pull arm. 40% Power loss. 0SSIL Speed and Force Adjustments The opening and closing speeds can be varied individually. Low Speed Closing. Lock Kick Low Speed Closing. To overcome the resistance of a striker plate, the lock kick can be adjusted to the required level of resistance. This will ensure that the lock bolt will securely engage into the striker plate. Controls Separate valves control door opening, closing and latching speeds. Screw for adjustment of 1 Opening Angle 10, Opening Speed pump pressure. 1.5-4 seconds Screw for adjustment of pump pressure. Screw for adjustment of Closing Speed 1.5-1.4 seconds Lock Kick (normally closed). Screw for adjustment of 3 Lock Kick Lock Kick (normally closed). Separate valves control door opening, closing and latching speeds. Separate 1 Opening valves Angle control 10, door Opening opening, Speed closing 1.5 and 4 seconds latching speeds. 1 Opening Closing Speed Angle 1.5 10, 4 Opening secondsspeed 1.5 4 seconds 3 Closing Lock Kick Speed 1.5 4 seconds 3 Lock Kick Low Speed Closing. Screw for adjustment of pump pressure. High Screw Speed for adjustment Closing of (normally Lock Kick (normally closed). closed). 1 Screw for adjustment Controls Screw for adjustment of Lock of spring Kickforce. Separate valves pump pressure. control door opening, closing and latching speeds. Low Speed Opening. 1 Opening Angle 10, Screw Opening for adjustment Speed of1.5 4 seconds Lock Kick (normally closed). High Speed Opening. Closing Speed 1.5 4 seconds 3 Lock Kick Controls Lock Kick To overcome the resistance of a striker plate, 1 the lock kick can be adjusted to the required level of resistance. This will ensure that the lock bolt Screw will securely for engage adjustment into the striker plate. max. Separate valves control 10 door opening, closing and latching speeds. 1 Opening Angle 10, Opening Speed 1.5 4 seconds Closing Speed 1.5 4 seconds 3 Lock Kick max. 10 1 3 Lock Kick Lock Kick Low Speed Closing. High Speed Closing (normally closed). 3 High Speed Closing (normally closed). High Speed Opening. 1 of spring force. Screw for adjustment Low Speed Opening. of spring force. Low Speed Opening. High Speed Opening. 1 High Speed Opening. To overcome the resistance of a striker plate, the lock kick can be adjusted to the required level of resistance. This will ensure To overcome the resistance of a striker plate, the lock kick can that the lock bolt will securely engage into the striker plate. be adjusted to the required level of resistance. This will ensure that the lock bolt will securely engage into the striker plate. High Speed Closing (normally closed). Scre of s Low Speed Opening. To overcome the resistance of a striker pla be adjusted to the required level of resista that the lock bolt will securely engage into 4.38 1 Lockwood 1 Product Catalogue Module (Version 1.)
Electromechanical Door Operators 0 Electromechanical Door Operator Double Door Coordination Unit Guarantees safe and correct closing of rebated doors. Often in combination with fire doors. door Slave r r doo Maste 6 5 "M aster" "Slave" 6 x 0PSIL Operators 1 x 0-100091 Coordinator Full length cover to be specified seperately. Reveal Depth Depth (A) (A) Reveal Reveal Reveal Depth Depth (A) (A) (A) Reveal Depth Pushing Pushing Pushing Pushing Pushing AAA A Pulling Pulling Pulling Pulling Pulling AA==00 AA == 00 AAA A Extension Extension Extension Extension Extension 0-173004 35 360 360 0-173004 AA==35 0-173004 0-173004 AA == 35 360 360 0-173004 A35 = 35 360 0-173191 Jointfor for 35 485-0-173191 Joint 35 485 0-173191 0-173191 Joint Joint forfor 35 35 485 485 0-173191 Joint for 35-485 Packer Packer Packer Packer Packer 0-1734BK 0-1734BK 0-1734BK 0-1734BK 130 AA==00 130 AA == 00 130 130 0-1734BK A 0-130 Standard==130 130 170 170 Standard = Standard Standard == 130 130 170 170 Standard = 130-170 Shaft Extension 0-173107 Shaft: Standard Shaft Extension: 0 0-173109 Shaft Extension: 50 Shaft Extension: 70 orr e ddooo or or Slalavve S e d e odo Sla Svlav Lockwood Product Catalogue Module (Version 1.) Door Closers 0-173108 4.39
0 Electromechanical Door Operator Operator with Motion Detector/Elbow Switch 1 x 0 Swing Door Operator 1() x 0-1700007 Radar Activation Unit 1() 0-1700008 Elbow Switch Outside activation unit detects the presence of an object in its range and automatically opens the door. Inside activation with an 0-1700008 Elbow switch for manual activation on one side. Ideally suited for doorways where usage is primarily for people carrying goods, pushing trolleys, wheelchairs or beds. Overhead Presence Detection (Supervisor) 1 x 0 Swing Door Operator 1() x 0-1700007 Radar Activation Unit 1() 0-1700008 Elbow Switch 1 x 0EXB 1 x 0ACCE 15 Zone presence detector The overhead presence detector mornitors any movement or obstruction within the ark of the door swing area. Safety for swing doors Single swing door WIDTH: 1.8M DEPTH: 1.M Safety for swing doors Double swing door It can be installed on either the pull or push side of the door. e.g if a person is standing inside the opening ark of the door, the door cannot be opened until the zone is clear of the obstruction. Note: This presence detector is a safety device to prevent the door opening or closing when an object is within the arch of the door, to activate the door opening or closing a door activation accessory also needs to be fitted. EG: radar activation unit or elbow switch. Operator with Safety Sensor (Eye tech) 1 x 0 Swing Door Operator 1() x 0-1700007 Radar Activation Unit 1() 0-1700008 Elbow Switch 1 x 0-738765 Eye-Tech infr-red presence detector 0 x 738765 = 340 long 0 x 738766 = 700 long 0x 738767 = 900 long 1 x 0-655614 Limit switch for presence push and go detection or indication Note: The presence detector operates as a door activator when a person enters the zone on the PUSH side. Once the door is open it remains open until the person has gone through. As a safety sensor, on the PUSH side it protects persons of objects from being hit by the door if the door has been stopped by the safety sensor on the PULL side and is closing after the pause time. In this case the door remains stationary and only moves in the unobstructed direction. Ideally suited for areas where beds and frail people need to ensure that the door will not close on them until completely clear of the doorway. 4.40 Lockwood Product Catalogue Module (Version 1.)
500 Swing Door Operator General Information The Lockwood 500 swing door operator has been designed for most internal door applications. The small discrete form factor allows the 500 to be installed on more doors than its larger counterpart. The unit can be installed to kg (push) or 60kg (pull) doors. The virtually silent electro mechanical operator offers variable opening and closing speeds, allowing the 500 to efficiently open doors without hitting unnecessary obstacles. The operator can be opened with a radar, card reader or push buttons. Further more, the intelligent Push & Go feature can sense that you are manually trying to push or pull the door and the operator will automatically assist you in opening the door and automatically close the door after a predetermined time. Features Push or pull doors (Push Standard) Low noise 60 kg door weight Allow 30% reduction for pushside Low resistance if used manually (Push & Go) Adjustable hold open time 0 to 60 seconds Pre-pull before opening when connected to electro mechanical lock Push & Go function as a standard function Built in 4 VDC/0.5 A power supply 6 door weight settings to minimise impact of obstacles Opening input can be controlled by various electronic devices such as readers, keypads, switches and radar beams Safety beam input for opening or closing Simple to program Software interface for maintenance and additional adjustments for the installer Applications Offices, meeting rooms Disabled homes and doors Public disabled toilets Baby changing rooms Nursing homes Child care facilities Residential use s 500SIL Push Operator Note: This is only to be used on internal doors where wind pressure will not effect the operation. Conforms in accordance to AS148.1-009 with regards to: Force required to operate door when manual mode is selected (Less than 0n) Push Side Door Operator 500SIL (includes mounting plate) Pull Side Door Operator 500SIL (includes mounting plate) + DC194/100000 Slide arm assembly for pull side Door Closers Lockwood Product Catalogue Module (Version 1.) 4.41
500 Swing Door Operator Operator with Motion Detector/Elbow Switch 1 x 500SIL Swing Door Operator 1() x 0-1700007 Radar Activation Unit 1() 0-1700008 Elbow Switch Outside activation unit detects the presence of an object in its range and automatically opens the door. Inside activation with an 0-1700008 Elbow switch for manual activation on one side. Ideally suited for doorways where usage is primarily for people carrying goods, pushing trolleys, wheelchairs or beds. Operator Interconnected to ES9000 Series Electric Strike Outside Keypad or card reader sends signal to open ES9000 strike to release Door Lock, operator signal sent to 500SIL to Open Door. Inside 0-17007 Radar Activation Unit or 0-170008 Elbow switch. Ideally suited to doors with locking requirements. Note: This solution also suitable for Lockwood 0 operator. 4.4 Lockwood Product Catalogue Module (Version 1.)
500 Swing Door Operator 60kgs 60kgs kgs 68 Min. 68 Min. 10 68 Frame depth H 3,5 Frame depth H Sliding arm to the push side Sliding arm to the pull side Standard arm to the push side Hinge line 0** Min. 1* Max. 3* 4 Ø 6 340 500 Swing Door Operator Technical Information Product size Weight Supply voltage Back-up Enclosure class Temperature range Current draw Max door weight (L) 53 x (H) 68 x (W) 3.5kg 30 VAC (±15%) 50 60 Hz Inlet 4 VDC (±15%) A IP0 Storage -0 70 C Operation 0 40 C Power output 4 VDC max 500 ma Potential free relay output 0.8 A @ 30 VDC resistive load 0.3 A @ 30 VDC inductive load kg with standard arm, closing side installation 60 kg with sliding arm, opening and closing side installation Specification Statement The operator must be syetrical suitable for left and right hand installations. The operator must have the capacity to push or pull doors up to kg. The operator must have 6 strength settings to minimise impact of obstacles. The operator must work in conjunction with a electromechanical mortice lock and have the intelligent pre-pull feature before unlocking the lock minimising the preload effect on the electro mechanical mortice lock. Door Closers Lockwood Product Catalogue Module (Version 1.) 4.43
ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience Lockwood is the leading brand in the Australian locking industry. With an established reputation for high quality products, this iconic brand provides a wide range of locking solutions to residential housing, coercial building and industrial application markets. Lockwood is supported by an extensive distribution and after-sales support network. Our customers include retailers, architects, trade and industrial personnel, locksmiths and security dealers. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. ASSA ABLOY is represented in all major regions, in both mature and emerging markets, with leading positions in Australia, Europe and North America. As the world s leading lock group, ASSA ABLOY offers a more complete product range of door opening solutions than any other company in the market. Australia 1300 LOCK UP (1300 56 587) lockweb.com.au New Zealand +64 9415 7111 assaabloy.co.nz ASSA ABLOY Australia Pty Ltd 35 Huntingdale Road Oakleigh, Victoria, 3166 Australia info.au@assaabloy.com assaabloy.com.au ASSA ABLOY New Zealand Ltd 6 strong Road Albany, North Shore City, 063 New Zealand info.nz@assaabloy.com assaabloy.co.nz ASSA ABLOY Australia Pty Limited ABN 90 086 451 907 013