Catalog 303 (March 2016) - PDF Free Download

Catalog 33 (March 16)

NDT: AN OVERVIEW Nondestructive testing (NDT) is a procedure used to examine and/or inspect materials and components to locate surface and subsurface defects in a way that allows such materials to be examined without changing or destroying their original design or structure. NDT plays a crucial role in everyday life. It is necessary to ensure structural integrity, safety and reliability in aircraft, motor vehicles, pipelines, seafaring vessels, bridges, trains, tunnels, power stations, refi neries and oil platforms. All are inspected using some method of nondestructive testing. Nondestructive testing is also a quality assurance production and management tool which can provide impressive results when used correctly. It requires an understanding of the various methods available, their capabilities and limitations, knowledge of the relevant standards and specifi cations for performing the tests. Materials, products and equipment that fail to achieve their design requirements or projected life due to undetected defects may require expensive repair or early replacement. Such defects may also be the cause of unsafe conditions or catastrophic failure, as well as the loss of revenue due to unplanned shutdowns. Nondestructive testing can be applied to each stage of an item s development, manufacture or construction. The item s materials and assembly can be examined using NDT and either accepted, rejected or repaired. NDT techniques can then be used to monitor the integrity of the item or structure throughout its service life. The most commonly used NDT methods are visual inspection, liquid penetrant inspection, magnetic particle inspection, Eddy current inspection, acoustic emission, ultrasonic inspection and radiography.

TABLE OF CONTENTS PAGE NO. UV-A LED INSPECTION LAMPS OLX-365 Series OPTI-LUX 365 OPX-365 OPTIMAX 365 OPK-3N OPTIMAX Multi-Lite TRI-365 Series TRITAN 365 TRI-365SBLC TRITAN 365 (Rolls-Royce RRES 961 Compliant) QDR-365 Series QUADRAN 365 QDR-365 S-Series QUADRAN 365 EK-3 EagleEye 8 9 1 1 16 UV-A STATIONARY LAMPS PM-16 Series PowerMAX 365 UV- Series SuperFlood 6 3 UV-A MDL INSPECTION LAMP ML-35 Series MAXIMA 3 UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT-365 On-Trak 365 3 BLUE LIGHT LED INSPECTION LAMPS OPX-5 OPTIMAX 5 TRI-5B TRITAN 5 PM-16B PowerMAX 5 37 38 BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT-5 On-Trak 5 DIGITAL RADIOMETERS XP- Accu-PRO XP- Accu-PRO Plus XRP-3 AccuMAX DM-365XA 6 7 Surface metal defect revealed using the TRITAN 365 UV-A inspection lamp and Zyglo liquid penetrant REPLACEMENT PARTS & ACCESSORIES CUSTOMER SERVICE/SUPPORT PRODUCT INDEX 8 5 55 Spectronics Corporation manufactures a wide array of medium and high-intensity inspection lamps and products that are used to detect and identify surface and subsurface fl aws in the performance of nondestructive testing utilizing the visual inspection, liquid penetrant and magnetic particle methods. For more information see www.spectroline.com.

UV-A LED INSPECTION LAMPS OLX-365 Series OPTI-LUX 365 UV-A LED Inspection Flashlights Affordable, Super-Compact and Designed Specifi cally for NDT! Feature a powerful UV-A (365 nm) LED light source coupled with a rugged anodized lamp body. Lightweight and compact, they reduce user fatigue while providing an extremely uniform beam profi le that surpasses those of more expensive lamps. Available in four models to suit your specifi c NDT needs: high-intensity or standard-intensity versions, each with or without an internal black light fi lter. Choice of nominal steady-state UV-A intensity of 1, µw/cm or maximum of,5 µw/cm at 15 inches (38 cm) Coverage area up to.5 inch (6.3 cm) diameter at 15 inches (38 cm), with minimum UV-A intensity of, µw/cm Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use Instant-on operation; lamp reaches full intensity immediately! Convenient on/off switch for easy, one-handed operation Powered by one rechargeable lithium-ion battery with an extra battery included with the lamp. Each provides hours of continuous inspection between charges. Meets ASTM UV-A intensity and wavelength specifi cations for LPT and MPT Both high- and standard-intensity versions are available with internal black light fi lter. Externally mounted black light fi lter with rubber bumper can be purchased as an accessory. Certifi cate of compliance for both wavelength and output measurements supplied with every lamp

Model OLX-365 High intensity, with clear fi lter Nominal steadystate UV-A (365 nm) intensity at 15 inches (38 cm) ➀ Visible light measurement 1, µw/cm.8 foot-candles (8.6 lux) Diameter of UV-A coverage area at 15 inches (38 cm) inch (5. cm) UV-A LED INSPECTION LAMPS OLX-365B High intensity, with internal black light fi lter 1, µw/cm. foot-candles (.3 lux) inch (5. cm) OPTI-LUX 365 fl ashlight with BF-365LX external black light fi lter accessory OLX-365FL Standard intensity, with clear fi lter OLX-365BFL Standard intensity, with internal black light fi lter,5 µw/cm maximum ➁,5 µw/cm maximum ➁.3 foot-candles (3. lux). foot-candles (.1 lux).5 inch (6.3 cm).5 inch (6.3 cm) Light Source: UV-A LED Lamp Style: Cordless fl ashlight Lamp Head Diameter: 1.5 in (3. cm) Length: 5.9 in (15 cm) Weight (w/battery):.6 oz (13 g) Power Requirement: One 3.7V ma/hr lithium-ion battery (rechargeable) Run Time: hours (continuous) Charge Time: hours (one or two batteries) Charging Cradle: Two-battery capability with AC and DC cord sets ➀ All UV-A intensity readings taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Replacement Parts & Accessories OPTI-LUX 365 Series fl ashlights come complete with lanyard, belt holster, two rechargeable batteries, smart charging cradle with AC and DC cord sets, UV-absorbing spectacles and a padded carrying case. BF-365LX External black light fi lter with rubber bumper 173 Dome lens 17568 Lithium-ion battery (rechargeable) 1767 Internal black light fi lter 17785 Internal clear fi lter 1817 Battery charging cradle with AC cord 185 DC cord set 1757 Belt holster UVS-3 UV-absorbing spectacles CC-365 Carrying case SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 5

UV-A LED INSPECTION LAMPS HIGH-INTENSITY MODELS OPTI-LUX 365 Series fl ashlights are available in two high-intensity models that are designed for NDT inspection applications requiring high UV-A output. The OLX-365 is equipped with a clear fi lter, while the OLX-365B comes with an internal black light fi lter that reduces the output of wavelengths longer than nm. Both versions provide a nominal steady-state UV-A intensity of 1, µw/cm at 15 inches (38 cm). UV-A BEAM PROFILE 1 1 1 5 3 (8) µw/cm 8 6 1 1 (3) () -1 (-3) 3 (8) - 3 (8) 1 (3) () -1 (-3) - -3 (-8) 1 (3) () -1 (-3) - -3 (-8) 3 1-1 - -3 (8) (3) () (-3) (-8) 1. NORMALIZED UV IRRADIANCE Typical wavelength output profi le of OPTI-LUX 365 with and without black light fi lter, with peak at 365 nm. Without Black Light Filter With Black Light Filter.75 Relative Output.5.5 5 3 35 5 5 55 6 65 7 Wavelength (nm) 6

STANDARD-INTENSITY MODELS OPTI-LUX 365 fl ashlights are also available in two standard-intensity models that are designed for inspection applications requiring limited UV-A output. The OLX-365FL is equipped with a clear fi lter, while the OLX-365BFL comes with an internal black light fi lter that reduces the output of wavelengths longer than nm. These lamps also offer a larger coverage area compared to high-intensity models. Both versions provide a nominal steady-state UV-A intensity of,5 µw/cm maximum at 15 inches (38 cm), and comply with aerospace industry standards. 6 UV-A BEAM PROFILE 5 3 (8) UV-A LED INSPECTION LAMPS µw/cm 1 1 (3) () -1 (-3) 3 (8) - 3 (8) 1 (3) () -1 (-3) - -3 (-8) 1 (3) () -1 (-3) - -3 (-8) 3 1-1 - -3 (8) (3) () (-3) (-8) SELECT WAVELENGTHS WITH AND WITHOUT BLACK LIGHT FILTER As the wavelength of the OPTI-LUX 365 moves into the visible light range, the black light fi lter signifi cantly reduces the UV-A output of the lamp by as much as 5% at nm. 1. Without Black Light Filter With Black Light Filter.75 Relative Output.5.5 385 39 395 5 1 15 5 3 Wavelength (nm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 7

UV-A LED INSPECTION LAMPS OPX-365 OPTIMAX 365 UV-A LED Inspection Flashlight (U.S. and foreign patents ts pending) Powerful, rechargeable, high-intensity UV-A inspection fl ashlight featuring state-of-the-art, ultra-hi-flux LED technology! Nominal steady-state UV-A intensity of 18, µw/cm at 15 inches (38 cm) Low visible light emission less than foot-candles ( lux) Electronic Intensity Stabilizer assures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Rubber lamp protector prevents damage to LED head Ergonomic, portable and rugged. Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use. Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges. Also available: DF-365 diffusing filter (sold separately). LAMP SPECIFICATIONS Style Length Cordless fl ashlight body with UV-A LED lamp head 8. inch (.3 cm) OPTIMAX 365 UV-A LED Inspection Flashlight comes complete with rubber lamp protector, smart AC and DC chargers, UV-absorbing spectacles, belt holster and padded carrying case. Weight 11.8 oz (335 g) (with Battery) Power Requirement Run Time Charge Time hours Spectacles 3.6V, AH NiMH internal battery stick (rechargeable) 9 minutes (continuous) UVS-3 UV-absorbing, clear UV-A BEAM PROFILE µw/cm 18 16 1 1 1 8 6 - -3 (-1) - (-8) -1 (-3) () X-INCHES (CM) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-INCHES (CM) 1 5 1 Y-INCHES (CM) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) X-INCHES (CM) 8

OPK-3N OPTIMAX Multi-Lite NDT Inspection Kit (U.S. patent no. 5,95,68; foreign patents pending) A New Powerful, Versatile, Multi-LED, NDT Light Source! Features three Qwik-Connect interchangeable LED lamp heads that connect to a rugged, black-anodized fl ashlight body. It provides singlewavelength illumination in UV-A and blue light, and is ideal for both pre-screening of fl uorescent particles in ambient light conditions and full-fledged NDT inspections utilizing magnetic particles or fluorescent penetrants. A convenient white light LED provides general illumination of dark work areas. UV-A LED INSPECTION LAMPS Super-powerful LED optical output with ultra-high intensity 365 nm UV-A and 5 nm blue light performance Provides nominal steady-state intensity of 18, µw/cm (UV LED) or 7, µw/cm (blue light LED) at 15 inches (38 cm) Blue light LED with patented thin-fi lm dichroic lens fi lters out long-wave visible light Electronic Intensity Stabilizer ensures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Lightweight, cordless, ergonomic design eliminates fatigue Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges (smart AC and DC chargers included). OPK-3N Multi-Lite Inspection Kit comes complete with three storage pouches for the LED lamp heads, smart AC and DC battery chargers, UV-absorbing spectacles, fl uorescentenhancing, yellow spectacles and a padded carrying case. UV-A BEAM PROFILE µw/cm µw/cm 18 16 1 1 1 8 6 - -3 (-1) - (-8) -1 (-3) () 1 9 x-inches (cm) 8 7 6 5 3 1 - -3 (-1) - (-8) -1 (-3) () 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) x-inches (cm) 1 (3) 3 (8) (1) y-inches (cm) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) y-inches (cm) 1 5 1 UV-A LED y-inches (cm) BLUE LIGHT BEAM PROFILE 1 5 1 Blue Light LED y-inches (cm) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) x-inches (cm) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) x-inches (cm) Style Length Cordless fl ashlight body with three interchangeable LED lamp heads 9. inch (.9 cm) Weight 15.3 oz (3 g) (with Battery) Power Requirement Run Time Charge Time hours Spectacles LAMP SPECIFICATIONS 3.6V, AH NiMH internal battery stick (rechargeable) 9 minutes (continuous) UVS-3 UV-absorbing, clear UVS- fl uorescent-enhancing, yellow SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 9

UV-A LED INSPECTION LAMPS TRI-365 Series TRITAN 365 Multi-LED, Broad-Beam UV-A Inspection Lamps Feature three ultra-hi-fl ux UV-A LEDs for fl uorescent inspection, plus a convenient white light LED to scan for surface fl aws and illuminate dark work areas. Their broadbeam confi guration provides an extremely wide coverage area, while a compact head design allows access into areas inaccessible to larger UV inspection lamps. Available in three models to meet your specifi c NDT inspection requirements: high-intensity, standard-intensity and standard-intensity with integral black light fi lters. Choice of one high-intensity model with a nominal steady-state UV-A intensity of 9 µw/cm or two standard-intensity models, both with a maximum UV-A intensity of less than 5, µw/cm at 15 inches (38 cm) Large inch (1 cm) diameter coverage area at 15 inches (38 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Grip-mounted, three-way rocker switch (white light/off/uv) for easy control of light sources Built-in fans keep LEDs cool to maintain optimum light output during extended use Long-lasting UV-A lenses reduce the rate of solarization Rubber bumper with Borofloat glass lens protects LEDs from damage Modular construction for easy servicing in the fi eld Choice of standard 8 foot (. m) or extra-long foot (6.1 m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional in-line power supply or industrial power supply with cord sets (sold separately). Meets ASTM UV-A intensity and wavelength specifi cations for LPT and MPT Certificate of compliance for both wavelength and output measurements supplied with every lamp UV-absorbing spectacles and soft carrying case included 1

TRITAN 365 faceplate shown with (left) and without (right) integral black light fi lters. Model TRI-365HB High intensity, with clear filter TRI-365DB Standard intensity, with clear filter Nominal steady-state UV-A (365 nm) intensity at 15 inches (38 cm) ➀ Visible light measurement 9, µw/cm < foot-candles ( lux) < 5, µw/cm maximum ➁ < 1 foot-candle (11 lux) Diameter of UV-A coverage area at 15 inches (38 cm) inch (1 cm) inch (1 cm) UV-A LED INSPECTION LAMPS TRI-365DBB Standard intensity, with integral black light filters < 5, µw/cm maximum ➁ <.5 foot-candle (5 lux) inch (1 cm) TRITAN 365 shown with optional PS-A (above) and PS-3A (below) power supplies. Light Source: 3 UV-A LEDs, 1 White Light LED Lamp Style: Pistol grip Lamp Head Diameter: 3.5 in (8.5 cm) Length: 8. in (.3 cm) Weight: 1 lb (5 g) White Light LED Intensity: foot-candles (,36 lux) Power Requirements: AC Lamp (TRI-365DB, TRI-365DBB, TRI-365HB) 1VAC* AC/DC Lamp (TRI-365MDB, TRI-365MDBB, TRI-365MHB) 1VAC*/1VDC Battery Pack: Type 1V, NiMH (rechargeable) Run Time 3.5 hours (continuous) Charge Time hours *Also available in 3V, V and 1V versions. ➀ All UV-A intensity readings were taken with the Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Replacement Parts & Accessories Also Available: TRITAN 365 M-Series portable, battery-operated AC/DC lamp kits. Include TRITAN 365 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UV-absorbing spectacles and soft carrying case. 1911 Standard, 8 foot (. m) AC power cord 1915 Extra-long, foot (6.1 m) AC power cord 1916 3.5 foot (1.1 m) DC power cord for M series lamps 17933 Particulate fi lter assembly 17955 Standard faceplate 18196 Faceplate with integral black light fi lters BP-3 BR-15A CC-37A FP-365 PSA-5A PS-A PS-3A UL-1 UVS-3 Battery pack with 1V rechargeable NiMH battery Smart AC charger Soft carrying case Rubber bumper with Borofl oat glass AC/DC power supply adapter for M series lamps Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6.1 m). In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). UV-A Lens UV-absorbing spectacles SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 11

UV-A LED INSPECTION LAMPS HIGH-INTENSITY MODEL UV-A BEAM PROFILE The TRITAN 365 lamp is available in a high-intensity model specifi cally designed for NDT inspection applications requiring high UV-A output. The TRI-365HB comes equipped with a clear glass fi lter and is tuned to provide a nominal steady-state UV-A intensity of 9, µw/cm at 15 inches (38 cm). 1 1 5 (1) 3 (8) µw/cm 8 6 1 TRI-365HB 1 (3) () -1 (-3) - -3 (-8) 3 (1) (8) 1-1 1 3 (1) (3) -1 - () (-3) - -3 - -3 (-8) (-3) () (3) (8) - (-8) (-1) (-1) - (-1) 3 1-1 - -3 - (1) (8) (3) () (-3) (-8) (-1) NORMALIZED UV IRRADIANCE Typical wavelength output profi le of TRITAN 365 Series with and without integral black light fi lters. Relative Output 1..75.5 TRI-365HB TRI-365DB TRI-365DBB.5 3 35 36 37 38 39 1 Wavelength (nm) 1

STANDARD-INTENSITY MODELS UV-A BEAM PROFILES µw/cm µw/cm 7 6 5 3 7 6 5 3 (1) 1 3 (8) 3-1 1 (3) (1) () (8) 1 - (-3) (3) -1-3 () (-3) - -3 - (-8) - (-1) (-8) (-1) (1) 1 3 (8) 3-1 1 (3) (1) () (8) 1 - (-3) (3) -1-3 () (-3) - -3 - (-8) - (-1) (-8) (-1) 5 1 TRI-365DB 5 1 TRI-365DBB (1) 3 (8) 1 (3) () -1 (-3) - -3 (-8) - (-1) (1) 3 (8) 1 (3) () -1 (-3) - -3 (-8) - (-1) 3 1-1 - -3 - (1) (8) (3) () (-3) (-8) (-1) 3 1-1 - -3 - (1) (8) (3) () (-3) (-8) (-1) The TRITAN 365 lamp is also available in two standard-intensity models that are designed for inspection applications requiring limited UV-A output. The TRI-365DB is fi tted with a clear glass fi lter. The TRI-365DBB is equipped with a faceplate with integral black light fi lters that cover each of the LEDs and reduce the output of wavelengths longer than nm. This addresses aerospace industry concerns. Both versions are tuned to ensure that they provide a maximum steady-state UV-A intensity of less than 5, µw/cm at 15 inches (38 cm). UV-A LED INSPECTION LAMPS SELECT WAVELENGTHS WITH AND WITHOUT BLACK LIGHT FILTER 1..75 TRI-365HB TRI-365DB TRI-365DBB As the wavelength of the TRITAN 365 moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm. Relative Output.5.5 38 385 39 395 5 1 15 Wavelength (nm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 13

UV-A LED INSPECTION LAMPS TRI-365 SBLC TRITAN 365 UV-A Inspection Lamp Key Features: Nominal steady-state UV-A intensity of less than 5, µw/cm at 15 inches (38 cm). Large inch (1 cm) diameter coverage area at 15 inches (38 cm), with a minimum UV-A intensity of,5 µw/cm. Low visible light emission less than.5 footcandle (5 lux). Long-lasting UV-A lenses reduce the rate of solarization. Thermal cut-off circuitry prevents lamp from going out of compliance when internal temperature exceeds specifications. Certificate of compliance and full serialized validation report for both output and wavelength measurements supplied with each lamp. LONG-LASTING UV-A LENSES reduce the rate of solarization RUBBER BUMPER with Borofl oat glass lens protects LEDs from damage BUILT-IN FANS maintain optimum light output Faceplate with INTEGRAL BLACK LIGHT FILTERS EASY CONTROL Grip-mounted, three-way rocker switch (white light/off/uv) THERMAL CUT-OFF CIRCUITRY prevents lamp from going out of compliance when internal temperature exceeds specifi cations TWO CORD CHOICES! Standard or Extra-Long with AC plug and rubber boot 1

TRI-365 ï ï ï ï ï ï ï Faceplate with integral blacklight filters reduce output of wavelengths longer than nm. White light LED allows for scanning of surface flaws or illuminating dark work spaces. Grip-mounted, three-way rocker switch (white light/off/uv) for easy control of light sources. Built-in fans keep LEDs cool to maintain optimum light output during extended use. Choice of standard 8 foot (. m) or extra-long foot (6.1 m) heavy-duty power cord with AC plug and rubber boot. Meets ASTM UV-A intensity and wavelength specifications for LPT and MPT. UV-absorbing spectacles and soft carrying case included. Model TRI-365SBLC Light Source: Lamp Style: Lamp Head Diameter: Length: Nominal steady-state UV-A (365 nm) intensity at 15 inches (38 cm) ➀ < 5, µw/cm maximum Visible light measurement <.5 foot-candle (5 lux) Diameter of UV-A coverage area at 15 inches (38 cm) inch (1 cm) 3 UV-A LEDs, 1 White Light LED Pistol grip 3.5 in (8.5 cm) 8. in (.3 cm) Weight: 1 lb (5 g) White Light LED Intensity: Power Requirements: *Also available in 3V, V and 1V versions. foot-candles (,36 lux) 1VAC* Power Cord ➀ All UV-A intensity readings were taken with the Spectroline AccuMAX Series meter, and are factory set to the values shown UV-A LED INSPECTION LAMPS FULL SERIALIZED VALIDATION REPORT CERTIFICATE OF COMPLIANCE UV-A BEAM PROFILE (15) 5 5 (1) 5 µw/cm 3 1 () 1 6 (15) (1) () 6 (15) (1) () - - - (-1) -6 - (-15) (-1) -6 (-15) (-1) (-15) (15) (1) () (-1) (-15) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 15

UV-A LED INSPECTION LAMPS QDR-365 Series TM Versatile, Dual-Intensity, Multi-LED, Broad-Beam NDT Inspection Lamps! Feature four ultra-hi-fl ux UV-A LEDs plus a convenient white light LED to quickly switch between fl uorescent inspection and fl aw location. A unique dual-intensity feature provides both high and standard UV-A and white light output for added versatility. The lamps broad-beam confi guration produces an extremely wide coverage area, making them ideal for both in-line and hand-held applications. Models are available either with or without integral black light fi lters to meet your specifi c inspection requirements. The QUADRAN 365 can be quickly mounted for in-line inspections using various Spectroline accessories (FA-1 fl exible arm shown). Dual-intensity capability: High setting produces a nominal steady-state UV-A intensity as high as 8, µw/cm ; standard setting produces a nominal steady-state intensity of,5 µw/cm, both at 15 inches (38 cm) Extremely large coverage area of up to 6 inches (15 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Conveniently located rocker switches for quick and easy control of light sources Built-in fan keeps LEDs cool to maintain optimum light output during extended use Rubber bumper with Borofl oat glass lens protects LEDs from damage Rugged, modular construction allows for easy fi eld serviceability Lamp handle pin receptacle allows for easy attachment of various Spectroline mounting accessories for in-line inspection applications (accessories sold separately) Choice of standard 8 foot (. m) or extra-long foot (6.1 m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional industrial power supply or in-line power supply with cord sets (sold separately). UV-absorbing spectacles and soft carrying case included 16

Model QDR-365A Standard Intensity, with clear fi lter High Intensity, with clear fi lter QDR-365BLA Standard Intensity, with intergral black light fi lters Nominal steadystate UV-A (365 nm) intensity at 15 inches (38 cm) ➀,5 µw/cm maximum Visible light measurement < 1 foot-candle (11 lux) 8, µw/cm < foot-candles ( lux),5 µw/cm maximum <.5 foot-candle (5 lux) UV-A coverage area (at minimum, µw/cm ) 5 in (13 cm) 6 in (15 cm) in (1 cm) UV-A LED INSPECTION LAMPS QUADRAN 365 faceplate shown with (top) and without (bottom) integral black light fi lters. High Intensity, with intergral black light fi lters 7, µw/cm < 1 foot-candle (11 lux) 6 in (15 cm) Light Source: UV-A LEDs, 1 White Light LED Lamp Style: Pistol grip Lamp Head (WxH): 6 x 5.5 in (15 x 1 cm) Length: 1 in (5 cm) Weight: 3 lb (1.36 kg) White Light LED Intensity: High setting: 3 foot-candles (3,9 lux) Low setting: 1 foot-candles (18 lux) Power Requirement: AC Lamp (QDR-365A, QDR-365BLA) 1VAC* power cord supplied with lamp AC/DC Lamp (QDR-365MA, QDR-365MBLA) 1VAC*/1VDC Battery Pack: Type 1V, NiMH (rechargeable) Run Time High intensity:.5 hours (continuous) Standard intensity:.5 hours (continuous) Charge Time hours *Also available in 3V, V and 1V versions. ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown Also Available: QUADRAN 365 M-Series portable, battery-operated AC/DC lamp kits. Include QUADRAN 365 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UV-absorbing spectacles and soft carrying case. SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 17

UV-A LED INSPECTION LAMPS QDR-365A MODELS UV-A BEAM PROFILES When the QDR-365A is in high intensity mode, the lamp provides a nominal steady-state UV-A intensity of 8, µw/cm at 15 inches (38 cm). When switched to the standard intensity mode, the QDR-365A provides a nominal steady-state UV-A intensity of,5 µw/cm at 15 inches (38 cm). µw/cm 1 8 6 (1) (1) () - - - (-1) () 1 5 1 QDR-365A (High Intensity) (1) () - - (-1) - - (1) () (-1) In addition, the lamp has a high/low switch to control the white light LED output. 6 5 6 (1) µw/cm 3 1 (1) () - - (-1) - () (1) 1 QDR-365A (Standard Intensity) () - - (-1) - - (1) () (-1) NORMALIZED UV IRRADIANCE Typical wavelength output profi le of QUADRAN 365 with and without intergral black light fi lters, with peak at 365 nm. Relative Output 1..75.5 QDR-365A (High Intensity) QDR-365A (Standard Intensity) QDR-365BLA (High Intensity) QDR-365BLA (Standard Intensity).5 3 35 36 37 38 39 1 Wavelength (nm) 18

µw/cm µw/cm 1 8 6 (1) 6 (1) () - QDR-365BLA MODELS UV-A BEAM PROFILES - (-1) - () () - - (-1) - () (1) (1) 1 5 1 QDR-365BLA (High Intensity) 5 1 QDR-365BLA (Standard Intensity) (1) () - - (-1) (1) () - - (-1) - - (1) () (-1) - - (1) () (-1) The QDR-365BLA is equipped with a faceplate with integral black light fi lters that reduce the output of wavelengths longer than nm. When in the high intensity mode, the lamp provides a nominal steady-state UV-A intensity of 7, µw/cm at 15 inches (38 cm). When switched to the standard intensity mode, the QDR-365BLA provides a nominal steady-state standard UV-A intensity of,5 µw/cm at 15 inches (38 cm). In addition, the lamp has a high/ low switch to control the white light LED output. UV-A LED INSPECTION LAMPS SELECT WAVELENGTHS WITH AND WITHOUT BLACK LIGHT FILTER Relative Output 1..75.5 QDR-365A (High Intensity) QDR-365A (Standard Intensity) QDR-365BLA (High Intensity) QDR-365BLA (Standard Intensity) As the wavelength of the QUADRAN 365 moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm..5 38 385 39 395 5 1 15 Wavelength (nm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 19

UV-A LED INSPECTION LAMPS QDR-365 S-Series TM Powerful, Multi-LED, Broad-Beam NDT Inspection Lamps! Feature four ultra-hi-flux UV-A LEDs plus a convenient white light LED to quickly switch between fluorescent inspection and flaw location. For increased flexibility, a unique dual-intensity feature provides high/low white light output control. The lamps broad-beam configuration produces an extremely wide coverage area, making them ideal for both in-line and hand-held applications. Two models are available, either with or without integral black light filters to meet your specific NDT inspection requirements. QUADRAN 365 S-Series lamps can be quickly mounted for in-line inspections using various Spectroline accessories (FA-1 fl exible arm shown). Choice of two models, both with a maximum standard UV-A intensity of,5 µw/cm at 15 inches (38 cm) Extremely large coverage area of up to 5 inches (13 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than 1 foot-candle (11 lux) Conveniently located rocker switches for quick and easy control of light sources Built-in fan keeps LEDs cool to maintain optimum light output during extended use Long-lasting UV-A lenses reduce the rate of solarization Rubber bumper with Borofl oat glass lens protects LEDs from damage Rugged, modular construction allows for easy fi eld serviceability Lamp handle pin receptacle allows for easy attachment of various Spectroline mounting accessories for in-line inspection applications (accessories sold separately) Choice of standard 8 foot (. m) or extra-long foot (6.1 m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional industrial power supply or in-line power supply with cord sets (sold separately). Meets ASTM UV-A intensity and wavelength specifi cations for LPT and MPT Certifi cate of compliance for both wavelength and output measurements supplied with every lamp UV-absorbing spectacles and soft carrying case included

Model QDR-365SA QDR-365SBLA With integral black light fi lters Nominal steadystate UV-A (365 nm) intensity at 15 inches (38 cm) ➀,5 µw/cm maximum ➁,5 µw/cm maximum ➁ Visible light measurement < 1 foot-candle (11 lux) <.5 foot-candle (5 lux) UV-A coverage area (at minimum, µw/cm ) 5 in (13 cm) in (1 cm) UV-A LED INSPECTION LAMPS QUADRAN 365 S-Series faceplate shown with (top) and without (bottom) integral black light fi lters. Light Source: UV-A LEDs, 1 White Light LED Lamp Style: Pistol grip Lamp Head (WxH): 6 x 5.5 in (15 x 1 cm) Length: 1 in (5 cm) Weight: 3 lb (1.36 kg) White Light LED Intensity: High setting: 3 foot-candles (3,9 lux) Low setting: 1 foot-candles (18 lux) Power Requirement: AC Lamp (QDR-365SA, QDR-365SBLA) 1VAC* power cord supplied with lamp AC/DC Lamp (QDR-365MSA, QDR-365MSBLA) 1VAC*/1VDC Battery Pack: Type 1V, NiMH (rechargeable) Run Time.5 hours (continuous) Charge Time hours *Also available in 3V, V and 1V versions. ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Also Available: QUADRAN 365 MS-Series portable, battery-operated AC/DC lamp kits. Include QUADRAN 365 UV lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, UV-absorbing spectacles and soft carrying case. SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 1

UV-A LED INSPECTION LAMPS UV-A BEAM PROFILES QUADRAN 365 S-Series lamps are available in two models (QDR-365SA and QDR-365SBLA). Both are designed for NDT inspection applications requiring limited UV-A output. The QDR- 365SA comes with a standard faceplate. The QDR-365SBLA is equipped with a faceplate containing integral black light fi lters that reduce the output of wavelengths longer than nm. µw/cm 6 5 3 1 (1) (1) () - () - - (-1) 6 1 QDR-365SA (1) () - - (-1) - - (1) () (-1) Both lamps are tuned to provide a nominal steady-state UV-A intensity of,5 µw/cm at 15 inches (38 cm). This addresses aerospace industry concerns. In addition, both lamps have a high/low switch to control the white light LED output. µw/cm 6 (1) () - - (-1) - () (1) 5 1 QDR-365SBLA (1) () - - (-1) - - (1) () (-1) 1. NORMALIZED UV IRRADIANCE Typical wavelength output profi le of QUADRAN 365 S-Series lamps with and without black light fi lters. QDR-365SA QDR-365SBLA 1. SELECT WAVELENGTHS WITH AND WITHOUT BLACK LIGHT FILTER As the wavelength of the QUADRAN 365 S-Series moves into the visible light range, the black light fi lters signifi cantly reduce the output of the lamp at nm. QDR-365SA QDR-365SBLA.75.75 Relative Output.5 Relative Output.5.5.5 3 35 36 37 38 39 1 38 385 39 395 5 1 15 Wavelength (nm) Wavelength (nm)

All QUADRAN 365 S-Series lamps are ideal for performing both in-line and hand-held inspections! Each lamp can easily be attached to a variety of Spectroline mounting accessories, as well as to our optional in-line power supplies. UV-A LED INSPECTION LAMPS QUADRAN 365 lamp shown with optional PS-A (left) and PS-3A (right) power supplies. Replacement Parts & Accessories for the QDR-365 & QDR-365 S-Series 1911 Standard, 8 foot (. m) AC power cord 1915 Extra-long, foot (6.1 m) AC power cord 1916 3.5 foot (1.1 m) DC power cord for M series lamps 179 Particulate filter assembly 179 Standard faceplate 189 Faceplate with integral black light fi lters B-6 Bench mount BP-3 Battery pack with 1V rechargeable NiMH battery BR-15A Smart AC charger CC- Soft carrying case FA-1 FP-55 PSA-5A PS-A Flexible arm Rubber bumper with Borofl oat glass AC/DC power supply adapter for M series lamps Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6.1 m). PS-3A In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). W-6 Wall mount with pin WM-1 Wall mounting bracket UL-1 UV-A Lens UVS-3 UV-absorbing spectacles SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 3

UV-A LED INSPECTION LAMPS EK-3 UV-A/White Light LED Inspection Kit (U.S. patent: 8,616,7; CN patent ZL11651.) Palm-Sized, Cool-Running, Hands-Free Light Source! Ideal for fl uorescent magnetic particle and penetrant testing, mining inspection and a variety of other specialized applications! Spray and inspect in one simple step! Compact, lightweight lamp with two ultra-high intensity UV-A (365 nm) LEDs for inspection, plus a three-led white light assembly for general illumination Adjustable strap allows lamp to be worn on a hard hat or directly on the head for hands-free operation Unique lamp mount/sprayer attachment permits lamp and spray can to be mounted together for convenient, single-handed fl uorescent yoke inspection Built-in fan keeps lamp cool to maintain optimum UV-A intensity during extended use Long-lasting UV-A lenses reduce the rate of solarization Splash guard with integral particulate fi lter protects UV lenses and cooling fan from damage Powered by a rechargeable lithium-ion battery (included). Provides up to 75 minutes of continuous inspection between charges. Certifi cate of compliance for both wavelength and output measurements supplied with every lamp

µw/cm LAMP SPECIFICATIONS Product Number: EE-365 Light Sources: UV LEDs, 3 white light LEDs Dimensions: Length 3.75 in (9.5 cm) Width.5 in (5.7 cm) Height 1.85 in (.7 cm) Weight with Battery: 8 oz (7 g) Power Requirement: One 3.7V ma/hr lithium-ion battery (rechargeable) Run Time: 75 minutes (continuous) Charge Time: hours (two batteries) Charging Cradle: Two-battery capability with AC and DC cord sets. Nominal Steady-State UV-A (365 nm) Intensity: 6 in (15 cm), µw/cm² 15 in (38 cm),5 µw/cm² in (61 cm), µw/cm² 36 in (91 cm) 1, µw/cm² UV-A LED INSPECTION LAMPS EK-3 EagleEye Kit comes with a lanyard, two replacement splash guards with integral particulate fi lters, two spare batteries, battery charging cradle with AC and DC cord sets, UV-absorbing spectacles and soft carrying case. NOTE: All UV-A intensity readings taken with a Spectroline AccuMAX Series meter UV-A BEAM PROFILE 6 5 3 1 - -3 (-1) - (-8) -1 (-3) () X-inches (cm) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-inches (cm) 6 1 Y-inches (cm) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) X-inches (cm) Replacement Parts & Accessories EE-365 LMS-1 HS-1 SG-1 UV-A/white light LED lamp Lamp mount/sprayer Head strap Splash guard with integral particulate fi lter (set of three) 1817 Battery charging cradle with AC cord 185 DC cord set for 1817 17568 Lithium-ion battery (rechargeable) UL-1 UV-A Lens UVS-3 UV-absorbing spectacles CC-37A Soft carrying case SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 5

UV-A STATIONARY LAMPS PM-16 Series UV-A LED Panel Flood Lamps Designed Specifi cally for NDT Professionals! PowerMAX 365 Series fl ood lamps feature a panel of 16 powerful UV-A (365 nm) LEDs specially engineered for non-destructive testing applications. These versatile, stationary light sources can be installed overhead or in-line, and can be ganged together to provide an even wider coverage area. Available in four models to meet your specifi c inspection needs: high-intensity and standardintensity versions, each with or without a black light fi lter. Ideal for NDT inspection booths, fl uorescent penetrant and magnetic particle inspection, screening of fl uorescent particles, wash station inspection and many other applications requiring maximum uniformity of UV-A coverage over a large area. Choice of two high-intensity models with a nominal steady-state UV-A intensity as high as 8, µw/cm or two standard-intensity models with a maximum UV-A intensity of,5 µw/cm at 15 inches (38 cm) Large coverage area of 15 inches by 6 inches (38 cm x 15 cm), with a minimum UV-A intensity of, µw/cm Low visible light emission less than foot-candles ( lux) Easily mountable for overhead inspection or in-line applications Built-in fans keep LEDs cool to maintain optimum light output during extended use Customizable multiple lamp units can be ganged together longitudinally or back-to-back for a larger coverage area to meet your specifi c inspection requirements! Both high- and standard-intensity versions available with or without black light fi lter Standard-intensity lamps meet ASTM UV-A intensity and wavelength specifi cations for LPT and MPT, and come with a certifi cate of compliance for both wavelength and output measurements 6

Top View Model Nominal steady-state UV-A (365 nm) intensity at 15 inches (38 cm) ➀ Visible light measurement UV-A coverage area (at minimum µw/cm ) PM-16UVH High intensity, with clear fi lter PM-16BLH High intensity, with black light fi lter PM-16UV Standard intensity, with clear fi lter 8, µw/cm < foot-candles ( lux) 6,5 µw/cm < 1 foot-candle (11 lux),5 µw/cm maximum ➁ < 1 foot-candle (11 lux) 15 in by 6 in (38 cm x 15 cm) 15 in by 6 in (38 cm x 15 cm) 15 in by 6 in (38 cm x 15 cm) UV-A STATIONARY LAMPS PM-16BL Standard intensity, with black light fi lter, µw/cm maximum ➁ <.5 foot-candle (5 lux) 15 in by 6 in (38 cm x 15 cm) For applications requiring extremely large coverage areas, the PowerMAX 365 can be quickly ganged together longitudinally (top) or back-to-back (below) using customized, easy-toinstall connecting plates and brackets. Light Source: 16 UV-A (365 nm) LEDs Lamp Style: Panel fl ood lamp Dimensions: 5.5 x 13.75 x 6 in (1 x 35 x 15 cm) (W x L x H) Weight: 9 lb ( kg) Power Requirement: AC power (main AC power cord supplied with the unit) ➀ All UV-A intensity readings were taken with Spectroline AccuMAX Series meter, and are factory set to the values shown ➁ To address aerospace industry concerns Top View Replacement Parts & Accessories 18177 AC power cord BF-365PM CF-1 Black light fi lter assembly Clear glass fi lter assembly 17918 Particulate air fi lter 17935 Retainer, LED assembly face plate CC- CP-1 CP- CP-3 UL-1 UVF-8 UVG-5 UVS-3 Connector cable for ganging lamps Top connecting plate for ganging lamps longitudinally Top connecting plate for ganging lamps back-to-back (Two required) Side connecting bracket for ganging lamps longitudinally (Two required) UV-A lens Face shield, UV-absorbing Goggles, UV-absorbing Spectacles, UV-absorbing SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 7

UV-A STATIONARY LAMPS HIGH-INTENSITY MODELS UV-A BEAM PROFILES PowerMAX 365 Series UV-A LED panel fl ood lamps are available in two high-intensity models that are specifi cally designed for NDT inspection applications requiring high UV-A output. The PM-16UVH is equipped with a clear glass fi lter and provides a nominal steady-state UV-A intensity of 8, µw/cm at 15 inches (38 cm). µw/cm 1 8 6-8 -6 (-) - (-15) (-1) - () - (-1) - () (1) 6 (1) (15) 8 () 1 5 1 PM-16UVH - (-1) - () (1) -8-6 - - 6 8 (-) (-15) (-1) () (1) (15) () The PM-16BLH is equipped with a black light fi lter that reduces the output of wavelengths longer than nm. It provides a nominal steady-state UV-A intensity of 6,5 µw/cm at 15 inches (38 cm). µw/cm 1 8 6-8 -6 (-) - (-15) (-1) - () - (-1) - () (1) 6 (1) (15) 8 () 1 5 1 PM-16BLH - (-1) - () (1) -8-6 - - 6 8 (-) (-15) (-1) () (1) (15) () NORMALIZED UV IRRADIANCE Typical wavelength output profi le of PowerMAX 365 Series with and without black light fi lter. 1..75 PM-16UV PM-16BL PM-16UVH PM-16BLH Relative Output.5.5 3 35 36 37 38 39 1 Wavelength (nm) 8

STANDARD-INTENSITY MODELS UV-A BEAM PROFILES µw/cm µw/cm 6 5 6 3 5 1-8 (-) -6 - (-15) - (-1) 3 1 () 6 (1) 8 (15) () (1) - - (-1) () -8-6 (-) - (-15) (-1) - () - (-1) - () (1) 6 (1) (15) 8 () 5 1 PM-16UV 5 1 PM-16BL - (-1) - () (1) - (-1) - () (1) -8-6 - - 6 8 (-) (-15) (-1) () (1) (15) () -8-6 - - 6 8 (-) (-15) (-1) () (1) (15) () PowerMAX 365 Series UV-A LED panel fl ood lamps are also available in two standardintensity models that are designed for NDT inspection applications requiring limited UV-A output. The PM-16UV is equipped with a clear glass filter and provides a nominal steady-state UV-A intensity of,5 µw/cm (maximum) at 15 inches (38 cm). The PM-16BL is equipped with a black light filter that reduces the output of wavelengths longer than nm. It provides a nominal steady-state UV-A intensity of, µw/cm (maximum) at 15 inches (38 cm). This addresses aerospace industry concerns. UV-A STATIONARY LAMPS SELECT WAVELENGTHS WITH AND WITHOUT BLACK LIGHT FILTER Relative Output 1..75.5 PM-16UV PM-16BL PM-16UVH PM-16BLH As the wavelength of the PowerMAX 365 moves into the visible light range, the black light fi lter signifi cantly reduces the output of the lamp at nm..5 38 385 39 395 5 1 15 Wavelength (nm) SPECTROLINE WWW.SPECTROLINE.COM 8.7.8888 9

UV-A STATIONARY LAMPS UV- Series SuperFlood Our Most Powerful UV-A Flood Lamps Designed Specifi cally for NDT These super-powerful and versatile lamps have been specially engineered for fl uorescent penetrant and magnetic particle inspection, parts degreasing inspections and wash station inspections. Powerful, -watt metal halide bulb, combined with tempered, heat-resistant low solarization UV fi lters provide the highest intensity over the largest area Unique twin-fi lter system eliminates hazardous UV-B and UV-C radiation escaping from lamp Easily mounts over automated magnetic particle systems or above penetrant inspection booths for the most accurate inspections of even the largest parts Compact design and built-in mounting features allow lamps to be positioned anywhere e even en in previously inaccessible areas The UV-A features a concentrated-beam refl ector designed to assure the highest concentrated UV-A intensity available. It has a peak steady-state UV-A intensity of 8, µw/cm within the lamp s center area, measured at 15 inches (38 cm). The lamp irradiates an area as large as 16 x 1 (1 cm x 5 cm), producing a nominal steady-state UV-A irradiance of not less than, µw/cm. The UV-B features a unique broad-beam refl ector designed to provide NDT inspectors with maximum uniformity of coverage over the largest area. It has a peak steady-state UV-A intensity of 5, µw/cm within the lamp s center area, measured at 15 inches (38 cm). The lamp irradiates an area as wide as 7 x 15 (69 cm x 38 cm) with unmatched uniformity, producing a nominal steady-state UV-A irradiance of not less than, µw/cm. UV-A BEAM PROFILE 1-15 (-38) µw/cm 9 8 7 6 5 3 1-15 -1 (-38) (-5) -5 (-13) () X-INCHES (CM) 5 (13) 1 15 (38) -15 (-38) -1 (-5) -5 (-13) () 5 (13) 1 15 (38) Y-INCHES (CM) UV-A 1 5 1 Y-INCHES (CM) -1 (-5) -5 (-13) () 5 (13) 1 15 (38) -15-1 -5 5 1 15 (-38) (-5) (-13) () (13) (38) X-INCHES (CM) 1 6 15 (38) 8 1 µw/cm 6 1 Y-INCHES (CM) 5 (13) () -5 (-13) 15 (38) 1 5 (13) X-INCHES (CM) 15 (38) 1-5 (13) () -5 (-13) -1 (-5) () -5-15 (-13) -1 (-38) (-5) -15 - - (-38) Y-INCHES (CM) UV-B -1 (-5) -15 (-38) - 15 1 5-5 -1-15 - (38) (13) () (-13) (-5) (-38) X-INCHES (CM) 3

A weld defect... UV-A STATIONARY LAMPS Revealed by the MAXIMA ML-35S UV-A inspection lamp using the liquid penetrant method. SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 31

UV-A MDL INSPECTION LAMP ML-35 Series MAXIMA Ultra-High Intensity UV-A Lamps These super-powerful lamps make NDT inspections easier, safer and more reliable. They feature state-of-the-art micro discharge light (MDL) technology with a fatigue-free ergonomic design. Powerful, 35 watt high-intensity MDL bulb Deliver up to 1 times the UV-A output of conventional HID inspection lamps Prefocused at the factory Instant on/off/restrike Lightweight, solid-state ballast Integral bulb/refl ector assembly Stay-cool, impact-resistant and dent-proof housing Battery-operated versions available All bulbs feature a rated life of, hours Come complete with both UV-absorbing and fl uorescent-enhancing spectacles The MAXIMA series consists of three models:» The ML-35S with a spot refl ector has a nominal steady-state UV-A intensity of 5, µw/cm at 15 inches (38 cm). Works even in direct sunlight!» The ML-35D with a spot refl ector and diffusing fi lter has a nominal steady-state UV-A intensity of 1, µw/cm at 15 inches (38 cm).» The ML-35FL with a fl ood refl ector has a nominal steady-state UV-A intensity of,5 µw/cm at 15 inches (38 cm). Line voltage model All models come standard with 8 foot (. m) primary and secondary cords. Lamps are also available with extended length primary cords or with a 35 foot (1.7 m) secondary cord housed in a retractable fl ying reel. In addition, all MAXIMA lamps are available in battery-operated M versions. Each includes a 1-volt, 7 amp/hr rechargeable battery that will operate the lamp for a full two hours. A battery charger and carrying case are included. ML-35 Series lamp with 35 foot (1.7 m) secondary cord housed in a retractable fl ying reel Battery-operated M version 3

UV-A BEAM PROFILES µw/cm µw/cm 6 5 3 1 - (-1) 6 5 3-3 (-8) - -1 (-3) () X-INCHES (CM) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-INCHES (CM) 6 1 1 ML-35S 1 Y-INCHES (CM) Y-INCHES (CM) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) X-INCHES (CM) UV-A MDL INSPECTION LAMP 1 - (-1) -3 (-8) - -1 (-3) () X-INCHES (CM) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-INCHES (CM) 1 ML-35D 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) X-INCHES (CM) 6 5 6 5 - (-1) -3 (-8) - µw/cm 3 1 Y-INCHES (CM) -1 (-3) () 1 (3) 1 - (-1) -3 (-8) - -1 (-3) () X-INCHES (CM) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-INCHES (CM) ML-35FL 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) X-INCHES (CM) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 33

UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT-365 Modular Inspection System (U.S. and foreign patents pending) The ONT-365 On-Trak is an innovative, track light-style modular inspection system. It features four broad-beam lamps, each of which utilizes three powerful, ultra-high-fl ux UV-A (365 nm) LEDs for inspection plus one white light LED for general illumination. This overhead lighting system allows inspectors to customize lamp beam patterns to suit their individual needs. Two lamp head assemblies can be added, as desired, to increase the coverage area. Perfect for NDT inspection booths, pre-inspections and screening applications requiring maximum uniformity of coverage over large areas. Cool-running, energy-effi cient LEDs Broad-beam profi les provide wide coverage area Electronic Intensity Stabilizers ensure consistent LED performance Instant-on operation; lamps reach full intensity immediately Built-in fans keep LEDs cool to maintain optimum UV-A intensity during extended use Long-lasting UV-A lenses reduce the rate of solarization Produces less than foot-candles of visible light Filter protectors with rubber bumpers and Borofl oat glass lenses prevent damage to LEDs Easily customizable! Move, adjust and add up to two lamp heads according to your specifi c inspection requirements (additional lamp heads sold separately) Optional remote control with three-position rocker switch provides added convenience and versatility Comes complete with UVS-3 UV-absorbing spectacles 3

LAMP SPECIFICATIONS Optional remote control with three-position rocker switch adds convenience and versatility Product Number: ONT-365 Light Sources: 3 UV-A LEDs and 1 white light LED per lamp head System dimensions: (L x W x H) 8.5 x 18.3 x 11 in (7 x 6 x 8 cm) Lamp: Head diameter: Length: 3.5 in (8.3 cm) 9.5 in ( cm) Platform Dimensions: (L x W x H) 8.5 x 18.3 x.5 in (7 x 6 x 6 cm) Platform Weight: 13 lb (5.9 kg) Power Supply Cord: 8 ft (. m) Power Supply: Input: 1- VAC 5/6 Hz Output: 1 VDC Nominal Steady-State UV-A (365 nm) Intensity: 15 in (38 cm) 9, µw/cm² UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM NOTE: UV-A intensity reading taken with a Spectroline AccuMAX Series meter UV-A BEAM PROFILE µw/cm 1 8 6 1 5 Y-inches (cm) -15 (-38) -1 (-5) -5 (-13) () 5 (13) 1 1-15 (-38) -1 (-5) -5 (-13) () X-inches (cm) -15 (-38) -1-5 (-5) 5 (-13) 5 () 1 (13) (13) 1 15 15 (38) (38) Y-inches (cm) 15 (38) -15-1 -5 5 1 15 (-38) (-5) (-13) () (13) (38) X-inches (cm) Replacement Parts & Accessories LA-365 PT- FP-1 UV-A/white light LED lamp head assembly Platform and track assembly Filter protector with rubber bumper and Borofl oat glass lens RC- UL-1 UVS-3 AC remote control with 8 foot (. m) cord UV-A Lens Spectacles, UV-absorbing AF- Air fi lter (package of ) UVG-5 Goggles, UV-absorbing PS-1A Power supply module UVF-8 Face shield, UV-absorbing SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 35

BLUE LIGHT LED INSPECTION LAMPS LED Light Sources in Blue Light Wavelengths! The importance of high-intensity UV-A black lights for proper magnetic particle or penetrant NDT inspection is well established. However, a concern for UV safety has always existed. Our new blue light inspection lamps and modular systems address this concern. While still no substitute for UV-A lamps, blue light does provide the safety and convenience desired for quick pre-inspection or screening of fluorescent particles in operating conditions with ambient light, saving time and limiting the use of black lights to only when necessary. TRITAN 5 OPTIMAX 5 Cordless & Lightweight Flashlight! Powerful, Broad-Beam Lamp! PowerMAX 5 Versatile, Stationary Flood Lamp! Powerful, Customizable Track Light System! On-Trak 5 36

OPX-5 OPTIMAX 5 Rechargeable Blue Light LED Flashlight (U.S. patent no. 5,95,68; foreign patents pending) This versatile, cordless inspection lamp features a high-intensity, 5 nm blue light LED, a black anodized lamp body and our patented, thin-fi lm dichroic lens to fi lter out long-wave visible light. Nominal steady-state blue light intensity of 7, µw/cm at 15 inches (38 cm) Patented, thin-fi lm dichroic lens improve contrast and fl uorescent response Electronic Intensity Stabilizer assures consistent performance. Beam strength will not weaken between charges! Instant-on operation. Lamp reaches full intensity immediately! Lightweight, cordless, ergonomic design eliminates fatigue Portable and rugged. Anodized aluminum lamp body minimizes corrosion and stands up to years of heavy use. Powered by a rechargeable NiMH battery. Provides 9 minutes of continuous inspection between charges. OPTIMAX 5 comes complete with smart AC and DC chargers, fl uorescent-enhancing, yellow spectacles, belt holster and rugged, padded carrying case. LAMP SPECIFICATIONS Style Cordless fl ashlight Lamp Head. inch (5.1 cm) Diameter Length 8. inch (.3 cm) Weight 11.8 oz (335 g) (with Battery) Power 3.6V, AH NiMH internal Requirement battery stick (rechargeable) Run Time 9 minutes (continuous) Charge Time hours BLUE LIGHT LED INSPECTION LAMPS BLUE LIGHT BEAM PROFILE 1 9 1 5 - (-1) -3 (-8) µw/cm 8 7 6 5 3 1 Y-INCHES (CM) - -1 (-3) () 1 (3) 1 - -3 (-1) - (-8) -1 (-3) () X-INCHES (CM) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) Y-INCHES (CM) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) X-INCHES (CM) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 37

BLUE LIGHT LED INSPECTION LAMPS TRI-5B Series TRITAN 5 Multi-LED, Broad-Beam Blue Light Lamp (U.S. patent no. 5,95,68; foreign patents pending) Feature three cool-running, ultrahigh fl ux 5 nm blue light LEDs with a broad-beam confi guration. This powerful lamp provides a wider coverage area than conventional inspection lamps, while its compact head design allows access into areas inaccessible to larger inspection lamps. Ideal for most non-destructive testing applications. Nominal steady-state blue light intensity of 9,5 µw/cm at 15 inches (38 cm) Large 5 inch (13 cm) diameter coverage area at 15 inches (38 cm) with a minimum intensity of, µw/cm Rubber bumper with patented thin-fi lm dichroic lens fi lters out long-wave visible light Electronic Intensity Stabilizer ensures consistent LED performance Built-in fans keep LEDs cool to maintain optimum light output during extended use Instant-on operation. Lamp reaches full intensity immediately! Rugged, ergonomic, angled lamp body provides safe, fatigue-free handling Choice of standard 8 foot (. m) or extra-long foot (6.1 m) heavy-duty power cord with AC plug and rubber boot. Also available: Optional in-line power supply or industrial power supply with cord sets (sold separately). Includes fl uorescent-enhancing, yellow spectacles and soft carrying case 38

µw/cm LAMP SPECIFICATIONS Style Pistol grip Light Source 3 blue light LEDs Lamp Head Diameter 5 in (13 cm) Length 8. in (.3 cm) Weight 1 lb (5 g) Power Requirements: AC lamp AC/DC lamp Battery Pack: Type Run Time Charge Time (TRI-5B) 1VAC* (TRI-5MB) 1VAC*/1VDC 1V, NiMH (rechargeable) 3.5 hours (continuous) hours *Also available in 3V, V and 1V versions. Replacement Parts & Accessories Also Available: TRITAN 5MB portable, battery-operated AC/DC lamp kit. Includes TRITAN 5 blue light LED lamp, rechargeable NiMH battery pack, power supply adapter with AC and DC cord sets, smart AC charger, fl uorescentenhancing, yellow spectacles and soft, lightweight carrying case. 1911 Standard, 8 foot (. m) AC power cord 1915 Extra-long, foot (6.1 m) AC power cord 1916 3.5 foot (1.1 m) DC power cord for M series lamps 17933 Particulate filter assembly BP-3 BR-15A CC-37A FP-5 PSA-5A PS-A PS-3A UVS- Battery pack with 1V rechargeable NiMH battery Smart AC charger Soft carrying case Rubber bumper with dichroic lens AC/DC power supply adapter for M series lamps Industrial power supply. Primary cord: 8 feet (. m); secondary cord: feet (6.1 m). In-line power supply. Primary cord: 8 feet (. m); secondary cord: 8 feet (. m). Fluorescent-enhancing spectacles, yellow BLUE LIGHT LED INSPECTION LAMPS BLUE LIGHT BEAM PROFILE 1 9 8 7 6 5 3 1 - -3 (-1) (-8) - -1 (-3) () x-inches (cm) 1 (3) 3 (8) (1) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) y-inches (cm) 1 5 1 y-inches (cm) - (-1) -3 (-8) - -1 (-3) () 1 (3) 3 (8) (1) - -3 - -1 1 3 (-1) (-8) (-3) () (3) (8) (1) x-inches (cm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 39

BLUE LIGHT LED INSPECTION LAMPS PM-16B Blue Light LED Panel Flood Lamp Designed Specifically for NDT Professionals! PowerMAX 5 fl ood lamp features a panel of 16 powerful blue light (5 nm) LEDs specially engineered for non-destructive testing applications when limiting the use of UV-A light is a requirement. This versatile, stationary light source can be installed overhead or in-line, and can be ganged together to provide an even wider coverage area. Ideal for NDT inspection booths, quick preinspection or screening of fl uorescent particles in ambient light conditions and any other applications requiring maximum uniformity of blue light coverage over a large area. Nominal steady-state blue light intensity of 1, µw/cm at 15 inches (38 cm) Large coverage area of 18 inches by 8 inches (6 cm x cm) with a minimum blue light intensity of, µw/cm Patented, thin-fi lm dichroic lens to fi lter out long-wave visible light Easily mountable for overhead inspection or in-line applications Built-in fans keep LEDs cool to maintain optimum light output during extended use Customizable multiple lamp units can be ganged together longitudinally or back-to-back for a larger coverage area to meet your specifi c inspection requirements!

µw/cm Top View LAMP SPECIFICATIONS Style Light Source Dimensions (WxLxH) Weight Power Requirement Panel fl ood lamp 16 blue light (5 nm) LEDs 5.5 x 13.75 x 6 in (1 x 35 x 15 cm) 9 lb ( kg) AC power (main AC power cord supplied with the unit) For applications requiring extremely large coverage areas, the PowerMAX 5 can be quickly ganged together longitudinally (top) or back-to-back (bottom) using customized, easy-to-install connecting plates and brackets. Replacement Parts & Accessories Top View 18177 AC power cord 17918 Particulate air fi lter 17935 Retainer, LED assembly face plate DF-5PM CC- CP-1 CP- CP-3 Dichroic fi lter assembly Connector cable for ganging lamps Top connecting plate for ganging lamps longitudinally Top connecting plate for ganging lamps back-to-back (two required) Side connecting bracket for ganging lamps longitudinally (two required) BLUE LIGHT LED INSPECTION LAMPS UVS- Fluorescent-enhancing spectacles, yellow BLUE LIGHT BEAM PROFILE 18 16 1 1 1 8 6-8 (-) -6 - (-15) - (-1) () X-inches (cm) 6 (1) (15) 8 () -8 (-) -6 (-15) - (-1) - () (1) 6 (15) 8 () Y-inches (cm) 1 5 1 Y-inches (cm) -8 (-) -6 (-15) - (-1) - () (1) 6 (15) 8 () -8-6 - - 6 8 (-) (-15) (-1) () (1) (15) () X-inches (cm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 1

BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT-5 Modular Inspection System Blue Light LED Inspection System (U.S. and foreign patents pending) The ONT-5 On-Trak is an innovative, modular, track light-style inspection system. It features four broad-beam lamps, each of which utilizes three powerful, blue light (5 nm) LEDs. This overhead lighting system provides a fast, safe and effective alternative to UV-A light. It allows inspectors to customize lamp beam patterns to suit their individual needs, and provides the ability to add two additional lamp head assemblies to further increase the coverage area. Perfect for NDT inspection booths, pre-inspections and screening of fluorescent particles in operating conditions with ambient light or any application requiring maximum uniformity of coverage over large areas. Powerful, cool running, energy-efficient blue light LEDs Broad-beam profiles provide wide coverage area Electronic Intensity Stabilizers ensure consistent LED performance Instant-on operation; lamps reach full intensity immediately Built-in fans keep LEDs cool to maintain optimum light output during extended use Rubber bumpers with patented thin-film dichroic lenses filter out long-wave visible light while preventing damage to the LEDs Easily customizable! Move, adjust and add up to two additional lamp heads according to your specific inspection requirements (additional lamp heads sold separately) Optional remote control with two-position rocker switch provides added convenience and versatility Comes complete with UVS- fluorescence-enhancing spectacles

LAMP SPECIFICATIONS Product Number: ONT-5 Light Sources: 3 blue light LEDs per lamp head System dimensions: (L x W x H) 8.5 x 18.3 x 11 in (7 x 6 x 8 cm) Lamp: Head diameter: Length: 3.5 in (8.3 cm) 9.5 in ( cm) Platform Dimensions: (L x W x H) 8.5 x 18.3 x.5 in (7 x 6 x 6 cm) Platform Weight: 13 lb (5.9 kg) Power Supply Cord: 8 ft (. m) Optional remote control with two-position rocker switch adds convenience and versatility Power Supply: Input: 1- VAC 5/6 Hz Output: 1 VDC Nominal Steady-State Blue Light (5 nm) Intensity: 15 in (38 cm) 9,5 µw/cm² NOTE: Blue light intensity reading taken with a Spectroline AccuMAX Series meter µw/cm 1 8 6 BLUE LIGHT BEAM PROFILE 1 5 1 Y-inches (cm) -15 (-38) -1 (-5) -5 (-13) () 5 (13) BLUE LIGHT LED MODULAR INSPECTION SYSTEM 1-15 (-38) -1 (-5) -5 (-13) () X-inches (cm) -15 (-38) -1-5 (-5) 5 (-13) 5 () 1 (13) (13) 1 15 15 (38) (38) Y-inches (cm) 15 (38) -15-1 -5 5 1 15 (-38) (-5) (-13) () (13) (38) X-inches (cm) Replacement Parts & Accessories LA-5 PS-1A PT- RC-3 Lamp head assembly with three blue light LEDs Power supply module Platform and track assembly AC remote control with 8 foot (. m) cord FP- UVS- Filter protector with rubber bumper and thin-fi lm dichroic lens Fluorescence-enhancing spectacles, yellow AF- Air fi lter (package of ) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 3

DIGITAL RADIOMETERS Series Digital Radiometer/Photometers The AccuPRO Series meters feature an advanced, microprocessor-controlled readout unit calibrated to accurately measure and display both UV-A and visible light readings for non-destructive testing applications. Available in two versions: The AccuPRO (XP-) readout unit features a single dualwavelength sensor detector designed to measure both ultraviolet and visible light. The AccuPRO Plus (XP-) features a single 3-in-1 multipurpose sensor that measures ultraviolet, visible and blue light. These compact, lightweight, battery-operated units are ideal for use in the fi eld, the factory or anywhere accurate light measurements are needed! Large, easy to read, LCD screen with -digit autoranging display Both units provide accurate readouts for UV-A irradiance as well as visible illuminance. AccuPRO Plus unit also measures blue light Simply to use, three-button interface. Toggle between light measurement modes. Overall accuracy greater than ± 5% per NIST standards Superior band-pass interference fi lter provides excellent cosine response One-touch PEAK with reset functions User-defi ned power save and automatic shutoff User-selectable, multilingual display settings at any operational level. Choose from English, French, German, Chinese and Spanish. Rugged meter features protective rubber housing for better grip and to help prevent accidental breakage Sealed sensor with water-resistant housing Multi-wavelength sensor directly attached to meter by 3 ft (.9 m) cord Complies with ASTM specifi cations for LPT and MPT Convenient on-board recharging Powered by four rechargeable AAA nickel-metal hydride batteries (included) Come complete with AC charger and padded carrying case

3-in-1 sensor AccuPRO Plus The AccuPRO meter features a dual-wavelength UV/visible light sensor, while the AccuPRO Plus (shown) features a 3-in-1 sensor that measures UV, visible and blue light. SPECIFICATIONS Readout Unit Resolution Screen Read Update Overall Accuracy -digit autoranging display 18 x 6 dot pixel chip on glass STN transmissive monochrome LCD.5 in (5.7cm) diagonal illuminated (backlit) Hz Better than + 5% with reference to NIST standards Temperature Coefficient +.5%/ C ( to 5 C) Power Requirements Dimensions Length 6. in (15. cm) Width 3. in (7.6 cm) Thickness 1. in (.5 cm) Weight 8 oz (7 g) Sensor Detector Length 3. in (7.6 cm) Width. in (5.1 cm) Thickness.5 in (1.3 cm) Weight 5.6 oz (159 g) Four AAA nickel-metal hydride batteries (rechargeable). AC charger included. Available in 1V, 3V, V or 1V versions. Spectral Range UV-A Sensor Visible Sensor Blue Light Sensor 3- nm 6-675 nm 1-75 nm XP- AccuPRO Dual Sensor (UV-A/VIS) Sensitive to UV and Visible Light Wavelength/Measurement Range UV-A (365 nm) Irradiance -1 mw/cm Visible (555 nm) Illuminance -5,38 Lux (-5 fc) XP- AccuPRO Plus 3-in-1 Sensor (UV-A/VIS/Blue) Sensitive to UV, Visible and Blue Light Wavelength/Measurement Range UV-A (365 nm) Irradiance -1 mw/cm Visible (555 nm) Illuminance -5,38 Lux (-5 fc) Blue (5 nm) -1 mw/cm DIGITAL RADIOMETERS SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 5

DIGITAL RADIOMETERS XRP-3 AccuMAX Digital Radiometer/Photometer Features an advanced microprocessor-controlled readout unit with a dual-wavelength sensor detector to measure both ultraviolet and visible light. Large, easy-to-read LCD screen Provides readouts for UV-A, visible irradiance or radiance Overall accuracy greater than ± 5% per NIST standards Choice of direct or USB cable connection between sensor detector and readout unit Superior bandpass interference filter Automatic zeroing, integration and signal hold Excellent cosine response User-selectable, multilingual display settings. Choose from English, French, German and Spanish. User-defined power save and automatic shutoff Rugged meter housing features removable, protective rubber boot for better grip and to help prevent accidental breakage Sealed sensor housing and USB connection with waterresistant adapter Compact, lightweight and battery-operated for convenient use in the factory, field or anywhere measurements are needed Complies with ASTM specifications for LPT and MPT Comes complete with readout unit, dual-wavelength sensor detector, USB cable with water-resistant adapter, protective rubber boot, two 9V alkaline batteries and padded carrying case. XR-1 readout unit with dual-wavelength sensor detector connected directly to unit Relative Spectral Response 1.9.8.7.6.5..3..1 3nm 35nm nm 5nm 5nm 55nm 6nm 65nm 7nm 75nm Wavelength (nm) XR-1 readout unit with dual-wavelength sensor detector connected to unit via USB cable SPECIFICATIONS Readout Unit (XR-1) Resolution -digit autoranging display Screen 18 x 6 dot pixel chip on glass STN transmissive monochrome LCD.8 in (7.1 cm) diagonal illuminated (backlit) Sample Rate 7.5 Hz (single sensor) 15 Hz (dual sensor) Read Update Hz Overall Accuracy Better than + 5% with reference to NIST standards Temperature Coefficient +.5%/ C ( to 5 C) Power Requirements Two 9V alkaline batteries (included) Dimensions Length 7.75 in (19.7 cm) Width.5 in (1.8 cm) Thickness 1.5 in (3. cm) Weight.8 lb (36 g) Dual UV-A/Visible Sensor Detector (XDS-1) Irradiance Range UV-A Sensor -1 mw/cm (-1, µw/cm ) Visible Sensor -5,3 lux (-5 fc) Spectral Range UV-A Sensor Visible Sensor 3- nm 6-675 nm Dimensions Length.75 in (1.1 cm) Width. in (5.1 cm) Thickness 7/8 in (. cm) Weight. lb (1 g) USB Cable (Length) 5 ft (1.5 m) 6

DM-365XA Digital UV-A Radiometer Provides increased accuracy for more repeatable results. Measures UV-A light sources with overall accuracy of ± 5% per NIST standards Autozeroing, excellent linearity and cosine response, solid-state design, compact, durable, simple operation, battery-level indicator Sealed silicone photodiode protects against shock and humidity Sensor housing is constructed with series of baffl es and unique self-sealing mechanism to eliminate light leakage Compact, lightweight and battery operated so measurements can be taken anywhere Complies with ASTM specifi cations for LPT and MPT SPECIFICATIONS Readout Unit Resolution 1 µw/cm Screen ½ digit, 7 segment, LED display.5 in (1.3 cm) high Overall Accuracy Better than ± 5% with reference to NIST standards Temperature Coefficient ±.5%/ C ( to 5 C) Irradiance Range -19,9 µw/cm Spectral Range 3- nm Power Requirements Two AA alkaline batteries (included) Length 7¼ in (18. cm) Width 3.5 in (8.9 cm) Thickness in (5.1 cm) Weight 1 lb (.5 kg) DIGITAL RADIOMETERS Sensor Detector Length Width Thickness Weight Cord Length 3 in (7.6 cm) in (5.1 cm).7 in (1.8 cm) 1¼ lb (.57 kg) 3 ft (91. cm) SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 7

REPLACEMENT PARTS & ACCESSORIES BP-1A BATTERY PACK Complete with RB-1S Smart Charger with Cordset, 1 Volt Rechargeable NiMH Battery and Nylon Carrying Case for MAXIMA TM ML-35 Series Lamps. (1V)* BP-3 BATTERY PACK Complete with BR-15A Smart Charger, 1 Volt Rechargeable NiMH Battery for QUADRAN QDR-365M, TRITAN TRI-365M and TRI-5MB AC/DC Lamp Kits. (1-1V)* CC-1A CARRYING CASE for BIB-15P Series. FC-Series and SB-1P Series Lamps CC-35 CARRYING CASE for MAXIMA ML-35 Series Lamps CC-365 CARRYING CASE for OPTIMAX OPX-365 and OPX-5 Flashlights CC-37A CARRYING CASE for EagleEye and TRITAN Series Lamp Kits CC- CARRYING CASE for QUADRAN 365 Series Lamp Kits UVS-3 SPECTACLES UV-Absorbing UVS- SPECTACLES Fluorescence-Enhancing UVF-8 FACE SHIELD UV-Absorbing UVG-5 GOGGLES UV-Absorbing *For other voltages, please see price list. Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 8

BLE-35PRA MDL BULB/POLISHED REFLECTOR ASSEMBLY for MAXIMA ML-35 Series Lamps 13 COATED SPOT REFLECTOR for MAXIMA ML-35 Series Lamps OF-3W LED LAMP HEAD, WHITE LIGHT for OPTIMAX OPK-3N Multi-Lite Lamp BLE-35RA MDL BULB/COATED REFLECTOR ASSEMBLY for MAXIMA ML-35 Series Lamps 151 ANODIZED FLOOD REFLECTOR for MAXIMA ML-35 Series Lamps OF-365UV LED LAMP HEAD, UV (365 NM) for OPTIMAX OPK-3N Multi-Lite Lamp BLE-35RAF MDL BULB/ANODIZED REFLECTOR ASSEMBLY for MAXIMA ML-35 Series Lamps for CH-5P/1 and MAXIMA ML-35 Series Lamps 13378 POLISHED REFLECTOR for MAXIMA ML-35 Series Lamps 173 DOME LENS for OPTI-LUX 365 Series LED Flashlights OF-5BD LED LAMP HEAD, BLUE LIGHT (5 NM) with dichroic lens for OPTIMAX OPK-3N Multi-Lite Lamp F11 UV-A FILTER for SuperFlood UV- Series Lamps BLE- METAL HALIDE BULB Watt for SuperFlood UV- Series Lamps 11958 MDL BULB 35 Watt for MAXIMA ML-35 Series Lamps UL-1 UV-A LENS for all UV-A (365 nm) LED Lamps, except TRITAN 365 TRI-365SBLC UL-11 UV-A LENS for TRITAN 365 TRI-365SBLC Lamp F35 DIFFUSING FILTER for FC-Series and MAXIMA ML-35 Series Lamps FB UV-B BLOCKING FILTER for SuperFlood UV- Series Lamps REPLACEMENT PARTS & ACCESSORIES SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 9

REPLACEMENT PARTS & ACCESSORIES F958 UV-A FILTER for BIB-15P Series, FC-Series and MAXIMA ML-35 Series Lamps FP-1 FILTER PROTECTOR with Rubber Bumper/Borofloat glass lens for ONT-365 On-Trak Inspection System Lamps LMS-1 LAMP MOUNT/SPRAYER for EagleEye Lamp 15565 RUBBER LAMP PROTECTOR for OPTIMAX Flashlights FP- FILTER PROTECTOR with Rubber Bumper/Dichoric glass lens for ONT-5 On-Trak blue light Inspection System Lamps 17796 RUBBER LAMP PROTECTOR for OPTI-LUX 365 Flashlight FP-365 FILTER PROTECTOR with Rubber Bumper/Borofloat Glass for TRITAN 365 Series Lamps SG-1 SPLASH GUARDS WITH INTEGRAL PARTICULATE FILTER for EagleEye Lamp (3 pack) BF-365LX EXTERNAL BLACK LIGHT FILTER WITH RUBBER BUMPER for OPTI-LUX 365 Flashlight FP-5 FILTER PROTECTOR with Rubber Bumper/Dichroic Filter for TRITAN 5 Series Lamps 173 HOLSTER for OPTIMAX OPX-365 and OPX-5 Flashlights DF-365 DIFFUSING FILTER for OPTIMAX OPX-365 Flashlight HS-1 HEAD STRAP for EagleEye Lamp 1757 BELT HOLSTER For OPTI-LUX 365 Series Flashlights Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 5

186 CORD SET Foot (.6 m), 7 Pin for MAXIMA ML-35 Series Lamps. (1V DC version) 1916 DC CORD SET 3.5 Foot (1.1 m) for QUADRAN A and TRITAN B M Series Lamps PS-A INDUSTRIAL POWER SUPPLY with cord sets for QUADRAN 365 and TRITAN Series Lamps. (1-1V)* 187 CORD SET 8 Foot (. m), 7 Pin for MAXIMA ML-35 Series Lamps. (3V version) 1817 BATTERY CHARGING CRADLE with AC cord for Eagle-Eye Inspection Lamp and OPTI-LUX 365 Series Flashlights. (1-1V)* PS-3A IN-LINE POWER SUPPLY for QUADRAN 365 and TRITAN Series Lamps. (1-1V)* 188 CORD SET 8 Foot (. m), 7 Pin for MAXIMA ML-35 Series Lamps. (115V and 1V versions) PSA-5A POWER SUPPLY ADAPTER with AC and 1V DC connections for QUADRAN and TRITAN M Series Lamps. (1-1V)* 185 DC CORD SET 1911 AC CORD SET 8 Foot (. m) for QUADRAN A and TRITAN B Series Lamps. (1-1V)* 1915 AC CORD SET Foot (6.1 m) for QUADRAN A and TRITAN B Series Lamps. (1-1V)* for Eagle-Eye Inspection Lamp and OPTI-LUX 365 Series Flashlights BR-15A SMART BATTERY CHARGER for BP-3 Battery Pack. (1-1V)* RB-1S SMART BATTERY CHARGER for BP-1A Battery Pack. (1V)* RB-3 SMART AC CHARGER for OPTIMAX OPK-3N, OPX-365 and OPX-5 Flashlights. (1-1V)* REPLACEMENT PARTS & ACCESSORIES *For other voltages, please see price list. SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 51

REPLACEMENT PARTS & ACCESSORIES RB-3DC 1V DC CHARGER for OPTIMAX OPK-3N, OPX-365 and OPX-5 Flashlights. XCB-1 WATER-RESISTANT USB CABLE WITH ADAPTER for AccuMAX Meter LH- LAMP HOLDER for OPTIMAX OPX-365 and OPX-5 Flashlights (for use with VF-1A) RC- AC REMOTE CONTROL for On-Trak ONT-365 UV-A Inspection System with 8 foot (. m) cord RC-3 AC REMOTE CONTROL for On-Trak ONT-5 Blue Light Inspection System with 8 foot (. m) cord XCC-1 CARRYING CASE for AccuMAX XRP-3 Meter XRB-1 RUBBER BOOT for AccuMAX XR-1 Readout Unit AB-1 ADAPTER BRACKET for Mounting Transformer-Based Spectroline HID Lamps onto a Magnaflux Wet Horizontal Mag Machine LH-3A LAMP HOLDER for TRITAN Series Lamps (for use with VF-1A, FA-1, WM-1, B-6 and W-6) VF-1A SPEC-STIK VERIFICATION FIXTURE for all Spectroline sensors, as well as HID, QUADRAN, TRITAN and OPTIMAX Series Lamps. NOTE: Lamp mounting accessories for TRITAN and OPTIMAX Series Lamps are sold separately (see LH- and LH-3A) 1568 BATTERY STICK WITH TAILCAP for OPTIMAX OPK-3N, OPX-365 and OPX-5 Flashlights B-6 BENCH MOUNT for all Spectroline HID, QUADRAN and TRITAN Series Lamps W-6 WALL MOUNT for all Spectroline HID and TRITAN Series Lamps 17568 LITHIUM-ION BATTERY Rechargeable for EagleEye Lamp and OPTI-LUX 365 LED Flashlights FA-1 FLEXIBLE ARM for all Spectroline HID, QUADRAN and TRITAN Series Lamps WM-1 WALL MOUNTING BRACKET for all Spectroline HID, QUADRAN and TRITAN Series Lamps Using genuine Spectroline replacement parts ensures that lamps will operate at their optimum performance. 5

REPLACEMENT PARTS & ACCESSORIES (HID LAMPS*) 1S SPOT BULB Ad-Medium Base, 1 Watt for SB-1P and FC-Series Lamps BLE-15CS-115/M CONCENTRATED SPOT BULB Self-Ballasted, 15 Watt for BIB-15P Series Lamps (115 volt version) FP-175 FILTER PROTECTOR/LAMP STAND for BIB-15PR and FC-Series Lamps 1S/M SPOT BULB Medium Base, 1 Watt for SB-1P and FC-Series Lamps BLE-15CS-3/M CONCENTRATED SPOT BULB Self-Ballasted, 15 Watt for BIB-15P Series Lamps (3 volt version) HGS-1A HEAT GUARD/STAND for SB-1P Series Lamps 1S/M-PQL UPGRADED, PREMIUM QUALITY LIGHTING SPOT BULB Medium Base, 1 Watt for SB-1P and FC-1 Series Lamps BLE-15FC-115/M CONCENTRATED SPOT BULB Self-Ballasted, 15 Watt for FC-15 Lamp (115 volt version) HGS-15A HEAT GUARD/STAND for BIB-15P and BIB-15PX Lamps BLE-15BS-115/M BROAD-BEAM BULB Self-Ballasted, 15 Watt for BIB-15P Series Lamps (115 volt version) BLE-15CS-1/M CONCENTRATED SPOT BULB Self-Ballasted, 15 Watt for BIB-15P Series Lamps (1 volt version) BLE-15FC-3/M CONCENTRATED SPOT BULB Self-Ballasted, 15 Watt for FC-15 Lamp, (3 volt version) *Mercury Vapor Bulbs. REPLACEMENT PARTS & ACCESSORIES SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 53

WAR R A N TY & C U S T O M E R S ER VIC E/S U PP O RT COMPANY BACKGROUND Spectronics Corporation is the world s leading manufacturer of ultraviolet equipment and ﬂuorescent materials. Spectronics supplies over 1, different products for the nondestructive testing, laboratory, biotechnology, industrial, electronics, semi-conductor, forensics, ﬁnancial, automotive, HVAC/R and other markets. Spectronics modern, 1, square-foot manufacturing facility and ofﬁce headquarters is located in Westbury, New York. Nearly personnel are involved in all phases of research and development, manufacturing, sales, marketing, customer service, and logistical and technical support. Over ﬁve decades since its inception, the goal of Spectronics is still the same to produce effective, top-quality products with the utmost dedication to customer satisfaction. SPECTRONICS CORPORATION Warranty All equipment is warranted against defects in manufacture. Spectronics Corporation s obligation under this warranty is limited to repairing or replacing, at the option of Spectronics Corporation, any part(s) of the product which, if properly installed, used and maintained, proves upon factory examination to have been defective in materials or workmanship within 1 months from the date of delivery to the customer, including LEDs. This warranty does not apply to any component which (1) is normally consumed in operation or () has a normal life inherently shorter than the warranty stated. For example, bulbs, filters and rechargeable batteries are warranted for 3 days; the 1S/M-PQL bulb is warranteed for 9 days. In addition, Spectronics Corporation does not warrant any instrument that has been subjected to misuse, negligence or accident, or has been repaired or altered by anyone other than Spectronics Corporation. This warranty is in place of all other warranties of quality. There are no other warranties either oral, written, express, implied or statutory. IMPLIED WARRANTIES OF FITNESS FOR PURPOSE AND MERCHANTABILITY ARE EXCLUDED. This warranty and your remedies thereunder are solely as stated in this form. In no event shall Spectronics Corporation be liable for special, indirect, incidental or consequential damages, nor for any damages arising out of delay in shipment or production. Product Speciﬁcations Spectronics Corporation reserves the right to alter product speciﬁcations without notice. Spectronics is under no obligation to make similar changes in its products previously produced. Product/Customer Support & Technical Assistance Product literature, instructions and a full staff of trained customer service representatives and technical service engineers are available for support. Additional product information and support are available on our website. Order Information Technical Assistance Local Sales Representatives Authorized Distributors PHONE (516) 333-8 FAX (516) 333-859 WWW.SPECTROLINE.COM 5

PRODUCT INDEX UV-A LED INSPECTION LAMPS EK-3............................. OLX-365............................, 5 OLX-365B............................. 5 OLX-365FL............................ 5 OLX-365BFL........................... 5 OPX-365.............................. 8 OPK-3N............................. 9 QDR-365A......................... 16, 17 QDR-365BLA.......................... 17 QDR-365MA........................... 17 QDR-365MBLA........................ 17 QDR-365SA........................, 1 QDR-365SBLA......................... 1 QDR-365MSA......................... 1 QDR-365MSBLA....................... 1 TRI-365DB............................ 11 TRI-365DBB........................... 11 TRI-365HB......................... 1, 11 TRI-365MDB.......................... 11 TRI-365MDBB......................... 11 TRI-365MHB.......................... 11 TRI-365SBLC.......................... 1 UV-A STATIONARY LAMPS PM-16BL........................ 6, 7 PM-16BLH.......................... 7 PM-16UV........................... 7 PM-16UVH.......................... 7 UV-A............................. 3 UV-B............................. 3 UV-A MDL INSPECTION LAMP ML-35D............................ 3 ML-35FL........................... 3 ML-35MD........................... 3 ML-35MFL.......................... 3 ML-35S............................ 3 UV-A/WHITE LIGHT LED MODULAR INSPECTION SYSTEM ONT-365.............................. 3 BLUE LIGHT LED INSPECTION LAMPS OPX-5............................. 37 PM-16B.......................... TRI-5B............................. 38 TRI-5MB........................... 39 BLUE LIGHT LED MODULAR INSPECTION SYSTEM ONT-5.............................. DIGITAL RADIOMETERS DM-365XA........................... 7 XRP-3............................ 6 XP-............................ XP-............................ REPLACEMENT PARTS & ACCESSORIES AB-1.............................. 5 AF-............................ 35, 3 B-6.............................. 3, 5 BF-365LX........................... 5, 5 BF-365PM............................ 7 BLE-35PRA........................... 9 BLE-35RA............................ 9 BLE-35RAF........................... 9 BLE-............................. 9 BP-1A.............................. 8 BP-3...................... 11, 3, 39, 8 BR-15A.................... 11, 3, 39, 51 CC-1A............................. 8 CC-............................ 7, 1 CC-35............................... 8 CC-365............................. 5, 8 CC-37A.................... 11, 5, 39, 8 CC-............................ 3, 8 CF-1............................... 7 CP-1............................ 7, 1 CP-............................ 7, 1 CP-3............................ 7, 1 DF-365............................. 8, 5 DF-5PM............................ 1 EE-365............................... 5 FA-1..................... 16,, 3, 5 FP-1............................ 35, 5 FP-........................... 3, 5 FP-365........................... 13, 5 FP-5........................... 39, 5 FP-55............................... 3 HS-1............................ 5, 5 LA-365............................... 35 LA-5............................... 3 LH-.............................. 5 LH-3A.............................. 5 LMS-1.......................... 5, 5 OF-3W............................. 9 OF-365UV............................ 9 OF-5BD............................ 9 PS-1A........................... 35, 3 PS-A..................... 11, 3, 39, 51 PS-3A..................... 11, 3, 39, 51 PSA-5A................... 11, 3, 39, 51 PT-............................ 35, 3 RB-1S........................... 8, 51 RB-3.............................. 51 RB-3DC............................ 5 RC-............................ 35, 5 RC-3............................ 3, 5 SG-1............................ 5, 5 UL-1.............. 9, 11, 3, 5, 7, 35, 9 UL-11............................ 1, 9 UVF-8......................... 7, 35, 8 UVG-5........................ 7, 35, 8 UVS-3......... 5, 8, 9, 11, 3, 5, 7, 35, 8 UVS-................... 9, 39, 1, 3, 8 VF-1A............................. 5 W-6.............................. 3, 5 WM-1.......................... 3, 5 XCB-1............................. 5 XCC-1............................. 5 XRB-1............................. 5 11958.............................. 9 13.............................. 9 151............................... 9 13378.............................. 9 186.............................. 51 187.............................. 51 188.............................. 51 15565............................... 9 1568.............................. 5 173............................... 5 173............................. 5, 9 17568.......................... 5, 5, 5 1757............................. 5, 5 1767................................ 5 17785................................ 5 17796............................... 5 17918............................ 7, 1 179............................... 3 17933............................ 11, 39 17935............................ 7, 1 179............................... 3 17955............................... 11 189............................... 3 18177............................ 7, 1 18196............................... 11 1817.......................... 5, 5, 51 185.......................... 5, 5, 51 1911...................... 11, 3, 39, 51 1915...................... 11, 3, 39, 51 1916...................... 11, 3, 39, 51 F11............................... 9 F35............................... 9 FB.............................. 9 F958............................... 9 REPLACEMENT PARTS & ACCESSORIES (HID LAMPS) BLE-15BS-115/M..................... 53 BLE-15CS-1/M..................... 53 BLE-15CS-115/M..................... 53 BLE-15CS-3/M..................... 53 BLE-15FC-115/M..................... 53 BLE-15FC-3/M..................... 53 FP-175............................... 53 HGS-1A............................ 53 HGS-15A............................ 53 1S................................ 53 1S/M.............................. 53 1S/M-PQL.......................... 53 PRODUCT INDEX SPECTROLINE WWW.SPECTROLINE.COM (516) 333-8 55

CONTACT US: 956 Brush Hollow Road, Westbury, NY 1159 Phone (516) 333-8 Fax (516) 333-859 WWW.SPECTROLINE.COM Follow us on at Spectroline Proud Members of: American Society for Nondestructive Testing American Society for Testing & Materials NDT 3/16 A98-11 PRINTED IN USA