INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC All 30175-31616 2 AND 4-DOOR P/N 08E10-SNA-100 Issue Date DEC 2005 NOTE: The interior illumination lights cannot be installed on 2-door vehicles equipped with fog lights. 3 Screws PARTS LIST Interior illumination light (with blue tape) 3 Flange nuts 2 Interior illumination lights (with white tape) Switch Interior illumination light harness Template Bracket Fuse label Wire tie with clip 10 Wire ties EPT sealer Switch trim 2 Switch lids 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 08E10-SNA-1000-91 1 of 13
Illustration of the Interior Illumination Light Installed on the Vehicle 3. If equipped, remove the driver s dashboard under cover (turn the knob counterclockwise, and release two clips and pin). FUSE CASE (2A) PIN TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Drill Drill bits (3 mm, 5 mm, and 10 mm) File Pushpin Utility knife Scissors Piece of steel wire Electrical tape Adhesive tape Eye protection (face shield, safety goggles, etc.) Scale Shop towel INSTALLATION (with white tape) (with blue tape) (with white tape) 5306010T Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. CLIPS (2) 4. Remove the driver s dashboard lower cover (eight clips). LOWER COVER 5202112T CLIPS (8) 5202121T KNOB 2 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
5. Lower the tilt lever, and move the steering wheel to its lowest position. After moving the steering wheel, return the tilt lever to its original position. 8. Shift to S or 2, and remove the lid from the dashboard center lower cover (four retaining tabs). SHOP TOWEL COMBINATION WIPER/ WASHER SHIFT LEVER ( S or 2 position) CENTER LOWER COVER SHOP TOWEL STEERING WHEEL SHIFT LEVER TILT LEVER RETAINING TABS (4) LID 5202130T 5306371T 9. Remove the passenger s dashboard under cover (four clips and two pins). 6. Cover the combination light switch, wiper/washer switch, and shift lever with a shop towel to protect them from damage. 7. Apply masking tape to the dashboard. Remove the instrument panel (one self-tapping screw and 11 clips), and unplug the vehicle connector. INSTRUMENT PANEL MASKING TAPE PINS (2) PASSENGER S 5306360T CLIPS (4) VEHICLE SELF- TAPPING CLIPS (11) 5624100B 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 3 of 13
10. Remove the two bolts. Open the glove box, push inward on the stoppers, and remove the glove box. 13. Plug the interior illumination light harness 6-pin connector into the fuse box 6-pin connector. STOPPER 6-PIN CONNECTING PORT FUSE BOX GLOVE BOX BOLT 5202260T Routing the Interior Illumination Light Harness 11. Route the interior illumination light harness 5-pin connector behind the fuse box, and pull it out through the opening of the air duct. 5-PIN BRANCH OF 100 mm 6-PIN NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the other accessory harness, and plug the interior illumination light harness into that connector. OTHER ACCESSORY 6-PIN 5306033T FUSE BOX OPENING OF AIR DUCT DUMMY (Discard.) BRANCH OF VEHICLE FUSE BOX 6-PIN 5306025T 12. Measure the vehicle harness from the point of branch as shown. Secure the interior illumination light harness (6-pin connector side) to the vehicle harness with one wire tie. 6-PIN 5213100T 4 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
14. Route the two interior illumination light harness 2- pin connectors onto the right side of the vehicle along the vehicle harness. 2-PIN FUSE LABEL ( 2A) 17. Route the wire through the opening for the lid of the dashboard center lower cover, and wind it onto the interior illumination light harness 2-pin connector (long harness side). ELECTRICAL TAPE STEEL WIRE FUSE CASE FRONT GROUND BOLT (Reuse.) ELECTRICAL TAPE GROUND TERMINAL 5306043T 2-PIN 5306050T 15. Attach the 2A fuse label to the interior illumination light harness fuse case. 16. Remove the ground bolt from the vehicle. Secure the interior illumination light harness ground terminal with the ground bolt you just removed. 18. Secure the other 2-pin connector to the interior illumination light harness with electrical tape. 19. Pull the interior illumination light harness out of the lid opening of the dashboard center lower cover by pulling the wire. STEEL WIRE ELECTRICAL TAPE 5306060T 20. Remove the wire and electrical tape from the interior illumination light harness. 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 5 of 13
21. Route the interior illumination light harness 2-pin connector to the passenger s side along the vehicle harness. 23. Secure the interior illumination light harness to the vehicle harness with three wire ties. OPENING IN GLOVE BOX VEHICLE 5306090T 22. Secure the interior illumination light harness to the vehicle harness with two wire ties. VEHICLE 5306070T 2-PIN 24. Secure the interior illumination light harness to the vehicle harness using four wire ties if the vehicle is equipped with the driver s dashboard under cover. Use three wire ties if the vehicle is without the driver s dashboard under cover. FUSE BOX 5306082T VEHICLE (Vehicle with driver s dashboard under cover only) WIRE TIE 5306100T 6 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
Installing the Interior Illumination Lights 25. Using scissors, cut out the template. 27. Secure the template (A) to the driver s dashboard under cover with tape by aligning it with the square hole at the end of the curve as shown. CURVED END PUSHPIN TEMPLATE (A) TEMPLATE 5604340T If the vehicle is equipped without a driver s dashboard under cover, go to step 34; otherwise, continue with step 26. 26. Pull up the insulator on the driver s dashboard under cover, and cut into it as shown. HOLE 5306130T 28. Using a pushpin, pierce the template at the three marked points. Remove the template. 60 mm 29. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points on the driver s dashboard under cover. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. DRILL (3 mm 5 mm drill bit) INSULATOR 5306120T DRILL (3 mm 10 mm drill bit) 5306140T 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 7 of 13
30. Cut the rib of the driver s dashboard under cover as shown. Using a file, remove any burrs from the edge. 32. Bundle the ambient light harness and secure the connector to the bracket using a wire tie with clip. WITH CLIP RIB BRACKET 5306171T 31. Route the interior illumination light (with white tape) connector through the 10 mm hole. Install the ambient light and bracket on the driver s dashboard under cover with the screw and flange nut. FLANGE NUT 5306150T 33. Reinstall the insulator to the driver s dashboard under cover, and pass the interior illumination light connector through the slit. INSULATOR BRACKET 5306350T UNDER COVER SLIT (with white tape) 5306160T 8 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
34. Position the template (B) on the lid of the dashboard center lower cover. PUSHPIN 37. Route the interior illumination light (with blue tape) connector through the 10 mm hole. Install the courtesy light on the lid with the screw and flange nut. AMBIENT FLANGE NUT LID OF CENTER LOWER COVER TEMPLATE (B) LID EPT SEALER (1/3) AMBIENT (with blue light) 5306180T 5306200T 35. Using a pushpin, pierce the template at the three marked points. Remove the template. 36. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points on the lid. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. 38. Using scissors, cut one EPT sealer into three equal pieces and use one of the pieces to wrap around the interior illumination light connector. 39. Secure the template (C) to the passenger s dashboard under cover with tape by aligning it with the square hole and the end of the curve as shown. Do not use the marks on the inside of the passenger s dashboard under cover. DRILL (3 mm 5 mm drill bit) DRILL (3 mm 10 mm drill bit) PUSHPIN CURVED END HOLE LID PASSENGER S TEMPLATE (C) 5306190T 5306220T 40. Using a pushpin, pierce the template at the three marked points. Remove the template. 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 9 of 13
41. While wearing eye protection, drill one 10 mm hole and two 5 mm holes at the pierced points on the passenger s dashboard under cover. First drill with a 3 mm bit, then finish with a 5 mm bit/10 mm bit as shown. Using a file, remove any burrs from the holes. Do not use the marks on the inside of the passenger s dashboard under cover. DRILL (3 mm 5 mm drill bit) DRILL (3 mm 10 mm drill bit) PASSENGER S If the vehicle is equipped without a driver s dashboard under cover, continue with steps 44 to 47; otherwise, go to step 48. 44. Assemble the interior illumination light (with white tape) with the bracket using the screw and flange nut. VEHICLE BRACKET FLANGE NUT (with white tape) 5306230T 42. Route the interior illumination light (with white tape) connector through the 10 mm hole. Install the interior illumination light on the passenger s dashboard under cover with the screw and flange nut. FUSE BOX EPT SEALER (1/3) BRACKET SELF-TAPPING 5306252T (Reuse.) 45. Remove the self-tapping screw from the vehicle bracket. Secure the bracket to the vehicle bracket using the self-tapping screw that you just removed. AMBIENT FLANGE NUT PASSENGER S 46. Wrap the remaining piece of EPT sealer that you cut into three equal pieces around the interior illumination light connector. EPT SEALER (1/3) 47. Plug the interior illumination light connector into the interior illumination light harness 2-pin connector, and secure them to the interior illumination light harness using a wire tie. AMBIENT (with white tape) 5306241T 43. Wrap another piece of the EPT sealer that you cut into three equal pieces around the interior illumination light connector. 2-PIN 5306303T 10 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
If the vehicle is equipped with a instrument panel pocket, continue with step 48; otherwise, go to step 51. 48. Remove the pocket from the instrument panel (three self-tapping screws). 51. Remove the switch lid from the instrument panel. INSTRUMENT PANEL SELF- TAPPING INSTRUMENT PANEL POCKET (Discard.) 5306260T LID (Discard.) 52. Install the switch in the instrument panel. 5306330T 53. Plug the interior illumination light harness 5-pin connector to the switch, and reinstall the instrument panel. 49. Install the switch trim to the instrument panel with the three self-tapping screws. SELF- TAPPING (Reuse.) TRIM INSTRUMENT PANEL LID 5306271T INSTRUMENT PANEL 5306281T 5-PIN 54. Reinstall the driver s dashboard lower cover and glove box. 50. Install the switch and two switch lids to the switch trim. Go to step 53. 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 11 of 13
55. If equipped with the driver s dashboard under cover, plug the interior illumination light harness 2- pin connector to the interior illumination light connector on the driver s dashboard under cover, and reinstall the under cover. 57. Plug the interior illumination light harness 2-pin connector to the interior illumination light connector on the passenger s dashboard under cover, and reinstall the under cover. 2-PIN 2-PIN 5306291T PASSENGER S 5306321T 56. Plug the interior illumination light harness 2-pin connector to the interior illumination light connector on the lid of the dashboard center lower cover, and reinstall the lid. 2-PIN CENTER LOWER COVER LID 5306310T 12 of 13 AII 30175-31616 (0601) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
58. Check that all wire harnesses are routed properly and all connectors are plugged in. 59. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. 60. Reconnect the negative cable to the battery. 61. Enter the customer s radio anti-theft code, and reset the radio station presets. 62. Reset the clock. HOW TO OPERATE Turn the headlight switch to the and position (headlights on low beam). Press the courtesy light switch. NOTE: When the battery is disconnected, the driver s window AUTO function is disabled. Start the engine. Push down on the driver s window switch until the window is fully open. Pull up on the driver s window switch to close the window completely, then hold the switch for two seconds or more. Lower and raise the driver s window to check the operation of the driver s window AUTO function. COURTESY HEAD OFF ON - ON ON OFF - - - 5306340T 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30175-31616 (0601) 13 of 13