Tech Bulletin Page 5- Flanged End FloaF loating Ball Valves Ideal Design for Process and Petrochemical Applications Size - 3 F FULL-FLO SERIES Models F50 Class 50 / F Class Full Port:/2" - 2" Standard Steam Working Pressure: 50 SWP, optional psig Size - 6 SF50 UNI-FLO SERIES Models SF50 Class 50 / SF Class Reduced Port: -2 Standard Steam Working Pressure: 50 SWP, optional psig Floating Ball Design Protected Seat Design O-Ring Backed Seat Fire Safe Designed to API 60-5 Spiral Wound Gasket with Secondary Metal to Metal Seal Open and Close Locking Device for Position Safety Lockout O-Ring Reinforced Packing Cryogenic Design Option Design Features I-SO-Mount Type, Actuator Mounting Pad Standard Super-Tek Seating Live Loaded Design Anti-Static Grounding Device Secondary Containment Option Flatted Shaft - Positive Flow Direction Ball Cavity Relief V-Ball Control Option Metal Seats Option, Class V & VI Valves for other flanged standards, such as DIN, JIS, BS, NFE and GB are also available. Website: www.flotite.com
Design Specif ications Standards of Compliance Travel stop incorprates Locking Device, can also be used as actuator lock out device Stop housing separates valve stop from packing gland, eliminates stop plate impacting on packing gland I-SO Mount Actuator Mounting, Bolt Design Eliminates Torsional Stress, Actuator can be Removed while Valve is under Full Pressure Recessed groove enables top flange to be be adapted with a secondary containment bonnet for fugitive emission, cryogenic service and other critical applications Pocketed and recessed seats with secondary metal backup seal. O-Ring encapsulated in the back of the seat, a unique flex-load energized seat design Tech Bulletin Page 5-2.5 - valve stems feature a NAMUR stem slot for ease of limit switch mounting Parallel flat stem head for positive ball position indication 2 pc design of diamond shaped packing gland preventing side loading due to uneven adjustment V-Ring Packing Rings Form a Rigid, High Cycle Seal O-Ring serves as second barrier for stem leakage Grounding antistatic devices at two locations enable electricity continuity Tapered Thrust Bearing Provides an Excellent Long Life Bearing Support Up to 6, Precision Investment Casting, Shell/ Wall ANSI B6.3 Fully Encapsulated Graphite Gaskets Isolates media from atomsphere Bolts and Nuts of High Quality and High Strength Ensure Structural Strength and Sealing Intergrity Flo-Tite s Flanged series valves with graphite stem packing meet the highest fire safety standards under extreme conditions. In the event of a fire, after heat destroys the primary resilient seat, the ball makes contact with the secondary metal seat, forming a secure seal. The body seal, composed of stainless steel and graphite wound into a spiral, prevents external leakage. The graphite stem rings prevent stem leakage. Ball Fire Safe: API60- & 5 Certified Burned Seat Metalto-Metal Contact Ball Spiral Wound Wire Gasket Metalto-Metal Contact Blow-Out Proof Standards and Specifications Valves covered in this bulletin are available to conform to the following industry standards and specifications All valves are manufactured to ISO 00 quality standards. WW-V-35C Federal Specification: Valve, Ball ANSI/ASME B6.0 Face-to-Face / End-to-End Dimensions of Ferrous Valves ANSI/ASME B6.5 Pipe Flanges and Flange Fittings ANSI/ASME B6.3 Valves - Flanged and Buttwelded End ANSI/ASME B3. Power Piping ANSI/ASME B3.3 Chemical Plant & Petroleum Refinery Piping ANSI/FCI 0-2-6 For Control Valve Leakage BS 655, Part 2 Testing of Valves - Specification for Fire Type Testing ISO 552:2 Metal Valves for use in Flanged Piping Systems ISA 5.02 Valve Sizing Coeffcient Cv, Piping Geometry Factor Fp and Pressure Drop Limitation XT ISA S5. Hydrostatic Testing of Control Valves ISO 52 Dimensions for Attachment of Actuators/Gear Boxes to Valves (ISO Mounting) MSS-SP-25 Standard Marking Systems for Valves MSS SP-55 Quality Standards for Castings MSS-SP-6 MSS-SP- MSS-SP-6 MSS-SP-2 MSS-SP-6 NACE MR0-5 API 60 API 6D API 5 MSS-SP-53 MSS-SP-3 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Pipe Line Flanges Pressure Testing of Valves Flanged or Butt and Weld End Ball Valves Having Full or Reduced Bores for General Liquid and Gas Service Terminology for Valves and Fittings Sulfide Stress Cracking Resistant Materials for Oilfield Equipment. Optional Standards & Specification Metal Ball valves Used in On-Off Service that have Buttwelded or Flanged Ends for Size /2 NPS - 2 NPS Specifications for Pipeline Valves Valve Inspection and Testing Quality Standard for Casting and Forging for Valves, Flanges and Fittings and Other Piping Components-Magnetic Paticle Examination Method Quality Standard for Casting and Forging for Valves, Flanges and Fittings and Other Piping Components-Liquid Penetrant Method 2 www.flotite.com
Bill of Materials / Full Port Valves DERRIN UHMWPE & NYLON R Saturated Steam SUPER TEK Saturated Steam Tech Bulletin Page 60- No. Name Stainless Carbon ASTM A35 CFM ASTM A26 WCB 2 Cap ASTM A35 CFM ASTM A26 WCB 6 3 * / /2-2 5 Packing Follower F50/F 2 5 Belleville Washer SS30 SS30 6 Lock Washer Exploded View 0 Ball / 22 2 Seat Repair Kits Gasket Soft Parts 3 0 Packing / Graphite / Graphite Packing Protector 50%+ 50%+ Item #,, 0, 2 Thrust Washer 25%Carbon+ 25%Carbon+, 2, 22, 23 Anti-Static 23 Valve Stop 5 Handle 6 Locking Device Handle Sleeve Plastic Plastic 23 Thin Nut Stud ASTM A3 B ASTM A3 B 6 20 Nut ASTM A Gr. ASTM A 2H 2 Bolt 2 5 22 O-Ring Locking Device Standard 23 Seat O-Ring 20 Bill of Materials No. Name Stainless Carbon 5 ASTM A35 CFM ASTM A26 WCB 2 Cap ASTM A35 CFM ASTM A26 WCB 3 * / 2-/2-2 Packing Gland ASTM A35 CF ASTM A35 CF F50/F 5 Packing Follower Exploded View 6 Ball / 5 Seat 0 2 5 6 Packing Packing Protector Gasket Thrust Washer O-Ring Anti-Static Travel Stopper Snap Ring Handle / Graphite 50%+ 25%Carbon+ Plated Ductile Iron / Graphite 50%+ 25%Carbon+ Plated Ductile Iron Repair Kits Soft Parts Item #,, 0,, 2, 22 Gland Bolt 6 Stop Housing 22 Housing Bolt 0 5 20 Stud ASTM A3 B ASTM A3 B 2 Nut ASTM A Gr. ASTM A 2H 2 22 Seat O-Ring 20 23 Set Screw 2 * Optional Material -PH Pressure Temperature Rating 2 3 S-Tek & Super Tek III PEEK 6 23 These ratings are conservative guide for general service. Previous experience in process or new development may permit applications at ratings above those shown. Higher Temperature Requirements 00 Pressure (Psig) 00 Class WCB Class WCB 00 Class CFM 00 Class CFM 600 600 500 00 500 00 Class 50 WCB Class 50 WCB Class 50 CFM Class 50 CFM 00 0 00 0-20 0 50 00 50 250 350 00 50 500 550 600-20 0 50 00 50 250 350 00 50 500 550 600 Temperature ( o F) Temperature ( o F) Saturated steam services above 50 psi use either Super Tek III or S-Tek. Saturated steam services above 250 psig use metal seats. Metal Seated Ball Valve will take full ANSI body metal material ratings. Pressure (Psig) 22 www.flotite.com 3
Dimensions - Full Bore Technical Submittal Tech Bulletin Page 6- F50/F SERIES Size /2-2 Size 2/2-2 Model F50 - ANSI Class 50 All Valves are hydrostatically Pressure Torque Est. Tested (Shell) & Air Pressure Tested Size A B C C D E F N S T Cv in-lb Weight (seat) to the following: Lbs Class 50: Class : /2.25 0.5 2.60.5 6.50. 3.50 2.3 0.62 62 Shell Test: Shell Test: 3/.62 0. 2..0 6.50 2.0 3. 2.5 0.62 3 0 5 50 psi for CS 25 psi for CS 5.00 0. 3.3 2.06. 2.05.25 3.2 0.62 00.5 25 psi for SS 00 psi for SS Seat Test: 0 psi Seat Test: 0 psi / 5.50.26 3.62 2.35. 2.5.62 3.50 0.62 2 20.5 /2 6.50.50. 2.65. 2.6 5.00 3. 0.62 20 20.5 Mounting Dimensions (F50/F) 2.00..53 2.0 0. 3.0 6.00.5 0.62 0 360 2 Size d K L M P W ISO 2/2.50 2.56 6.22 3.3 5. 3.0.00 5.50 0.5 0 620 33.5 /2 ~3/.65 0.3 0.55 0.250 0.3 #0-2UNC F0 ~/ 3.00 3.00 6.5 3.6 5. 3..50 6.00 0.5 20 00 2.5. 0.3 0.5 0.35 0.3 /-20UNC F05 /2 ~2 2.6 0.55 0. 0.3 0.62 5/6-UNC F0.00.00.20.0 5...00.50 0.5 25 00 62 2/2 ~.02.5 3.0 0.66.0 /2-UNC F0 6 5.5 5..2.20 25.6.62.0.50 0. 00 600 65.0..6.60 3..35.5.5 0. 000 00 262 Size /2-2 0 2.0... 3.0 0.5 6.0 2.25.00 500 000 6 2 2.0. 6..5 3.0 2.0.0 2.0.00 2200 20 Large sizes available in our trunnion series Model F - ANSI Class Torque Est. Size A B C C D E F N S T Cv in-lb Weight Lbs Size 2/2 - /2 5.5 0.5 2.60.5 6.50. 3.5 2.62 0.62 5 65 5 3/ 6.00 0. 2..0 6.50 2.0.62 3.25 0.5 0 5 6.50 0. 3.3 2.06. 2.. 3.50 0.5 0 05 0 /.00.26 3.62 2.35. 2.5 5.25 3. 0.5 252 C/F /2.50.50. 2.65. 2.6 6.2.50 0. 2 2.50..53 2.0 0. 3.0 6.50 5.00 0.5 30 3 25 2 /2.50 2.56 6.22 3.3 5. 3.0.50 5. 0. 6 65 2 3.2 3.00 6.5 3.6 5. 3..25 6.62 0. 00 0 60 2.0.00.20.0 5.. 0.0. 0. 00 5 3 6 5. 5..2.20 25.6.62 2.5 2 0.62 0. 00 30 22 * Verify mounting dimensions before manufacturing mounting hardware!.5..6.60 3..35 5.0 2.0.00 0000 035 3 0 22.3... 3.0 0.5.5 6 5.25.2 350 50 56 * For 6 and larger size mounting 2 25.50. 6..5 3.0 2.0 20.5 6.5.25 250 C/F dimensions, consult factory Due to continuous development & improvement of our product range, we reserve the right to alter the dimensions & technical data included in this brochure. www.flotite.com
Bill of Materials / Standard Bore Valves No. Name 2 Cap 3 * Packing Follower 5 Belleville Washer 6 lock Washer Ball Seat Gasket 0 Packing Packing Protector 2 Thrust Washer Anti-Static Valve Stop 5 Handle 6 Locking Device Handle Sleeve Thin Nut Bolt 20 O-Ring Bill of Materials Stainless ASTM A35 CFM ASTM A35 CFM SS30 / Graphite 50%+ 25%Carbon+ Plastic No. Name Stainless ASTM A35 CFM 2 Cap ASTM A35 CFM 3 * Packing Gland ASTM A35 CF 5 Belleville Follower 6 Ball Seat Packing / Graphite Packing Protector 50%+ 0 Gasket R/ Graphite Thrust Washer 25%Carbon+ 2 O-Ring Anti-Static Travel Stopper 5 Snap Ring Plated 6 Handle Ductile lron Gland Bolt Stop Housing Housing Bolt 20 Set Screw * Optional Material -PH Carbon ASTM A26 WCB ASTM A26 WCB / SS30 / / Graphite 50%+ 25%Carbon+ Plastic Carbon Carbon ASTM A26 WCB ASTM A26 WCB / ASTM A35 CF / / Graphite 50%+ 25%Carbon+ Plated Ductile lron /2-2 SF50/SF Exploded View Repair Kits Soft Parts Item #,, 0,, 2, 20 2 5 Pressure Temperature Rating 5 20 3 Tech Bulletin Page 62-5 0 6 5 6 Locking Device Standard 3-2 SF50/SF Exploded View 2 3 6 6 Repair Kits Soft Parts Item #,,, 0,, 2 These ratings are conservative guide for general service. Previous experience in process or new development may permit applications at ratings above those shown. Higher Temperature Requirements 00 Pressure (Psig) 00 Class WCB Class WCB 00 Class CFM 00 Class CFM 600 600 500 00 Class 50 WCB Class 50 CFM DERRIN UHMWPE & NYLON R 00 00 0 0-20 0 50 00 50 250 350 00 50 500 550 600-20 0 50 00 50 250 350 00 50 500 550 600 Temperature ( o F) Temperature ( o F) Saturated steam services above 50 psi use either Super Tek III or S-Tek. Saturated steam services above 250 psig use metal seats. Metal Seated Ball Valve will take full ANSI body metal material ratings. Saturated Steam SUPER TEK Pressure (Psig) 500 00 Class 50 WCB Class 50 CFM Saturated Steam S-Tek & Super Tek III PEEK 0 20 2 www.flotite.com 5
Dimensions - Reduced Bore Technical Submittal Tech Bulletin Page 63- SF50/SF Series Size -2 Size 2/2-2 Model SF50 - ANSI Class 50 Mounting Dimensions (SF50/SF) Torque Est. Size d K L M P W ISO Size A B C C D E F N S T Cv in-lb Weight.65 0.3 0.5 0.250 0.3 #0-2UNC F0 Lbs /2. 0.3 0.5 0.35 0.3 /-20UNC F05 5.00 0. 2..6 6.50 2.0.25 3. 0.63 33 5 2 2.6 0.55 0. 0.3 0.62 5/6-UNC F0 /2 6.50.26 3.62 2.20. 2. 5.00 3. 0.63 5 252 2 3.02.3 2.5 0.66.0 /2-UNC F0 2.00.50.20 2.6 0. 2.56 6.00.5 0.5 60 2,6.02.5 3.0 0.66.0 /2-UNC F0 3.00 2.56 6.22 3. 5. 3.0.50 6.00 0.5 30 65 3,0.2.65 3.5.02. /2-UNC F2.00 3.00 6.3.6 5. 3.35.00.50 0.5 00 0 55 2 5.5 2. 3.6.3. 5/-UNC F 6 0.5.00.52.33 5..6.0.50 0. 00 5 0.5 5. 0. 6.5 25.6 5.5.5.5 0. 2 30 0.0..6.62 3. 6.5 6.0 2.25.00 000 035 35 2.0. 2..2 3.0.00.0 2.0.00 00 50 5 Size -2 Model SF - ANSI Class Torque Est. Size A B C C D E F N S T Cv in-lb Weight Lbs 6.50 0. 2..6 6.50 2.. 3.50 0.5 33 00 Size /2.50.26 3.62 2.20. 2.60 6..50 0. 5 265 2/2-2 2.50.50. 2.6 0. 2.2 6.50 5.00 0.5 60 2 25 3. 2.2 6. 3. 5. 3.5.2 6.62 0. 30 6 56 2.0 3.5.6.6 5. 3.6 0.0. 0. 00 2 5 6 5. 3..52.33 5..6 2.5 2 0.63 0. 00 3 6.5 5. 0. 6.5 25.6 5.5 5.0 2.0.00 2 502 303 *Verify mounting dimensions before 0.0..6.62 3. 6.5.5 6 5.25. 000 05 6 manufacturing mounting hardware! 2.5.53..2 3.0.00 20.5 6.5.25 00 3 Unique Design Feature Tamper Proof Locking Device Standard Valve topworks incorporates a tamper proof locking device, locks in open or closed positions. When valve stop housing is removed, four bolts remain to mount actuator bracket. Size: 2/2 ~ Ball Design Added Safety Feature Pressure Relieving & Equalizing Seat Design Specially designed seats allow equaliza tion of pressure in the ball cavity which reduces operating torque and increases seat life. All balls are provided with a / hole drilled into the stem slot of each ball to prevent excessive pressure build up in the cavity from trapped liq uid when the valve is in the open position. Due to continuous development & improvement of our product range, we reserve the right to alter the dimensions & technical data included in this brochure. 6 www.flotite.com
High-Tech Design Features Flo-Tite s Van Guard Sealing System, designed to minimize fugitive emissions. Increases safety and provide an immediate ball valve solution to the newer EPA performance requirements, for valves meeting with a leak rate of 500ppm. Flo-Tite s Van Guard Seal,state of the art stem sealing system. Incorporating a triple set of valve stem seals. This unique system eliminates the possibility of valve stem leaks in most all media applications. STAGE I - FRONT LINE Stage I provides a front line defense against leakage. The blow-out proof stem shoulder has a 5 degree bell shaped slope. The bell shaped design offers more sealing surface, effectively blocking all leak paths during rotation. The wedging action of the portion of the stem is far superior to the common small flat stem shoulder design. STAGE II - GUIDE-SEAL The O-ring originated early in valve design and has been a proven performer in high cycle applications. Its basic function reduces the potential of machining inperfections and provides a low torque flexible seal. This center guide also helps to maintain a perfect stem alignment, by eliminating side loading stress which can cause stem leaks. STAGE III - LIVE-SEAL Live-seal is considered the intellectual component and the workhorse of Flo-Tite s Van Guard stem sealing system. Working in unison with stages I and II, stage III calls upon the use of V-Ring packing sets which expands sideways as it is compressed and pressurized blocking all air pockets. The Van-Guard stem system is energized by disk or coil springs which continueouly adjusts packing compression to componsate for wear, pressure or temperature changes. Whether your service involves volatile organic compounds, volatile hazardous chemicals, or air pollutants, Flo-Tite s ball valves are by design dependable, long lasting and fully maintainable. Flo-Tite has various valve solutions and designs that provides end-users freedom of choice for the toughest requirements imposed by the industry and by international standards. Flex-Load Energized Seat Design Size /2-2 Anti- Extrusion Packing O-Ring Size 2/2-2 Coil Spring Anti- Extrusion Packing O-Ring Tech Bulletin Page 6- Tab Washer Belleville Washer Follower Conical Front Seal Packing Gland Energized Follower Conical Front Seal Seat O Ring Seat Ball Upstream Pressure O Rings are inserted behind valve seats. The O Ring exerts only a minimum amount of pressure on the seats that in turn helps seal on both upstream and downstream sides of the ball. Also, helps provide additional seat memory. Ideal for high cycle, very low pressure & vacuum service applications. Flanged Valves with Media Containment Units The I-SO-Mount platform is ideal for the addition of our secondary containment units. Flo-Tite s media containment unit offers in-line maintenance for stem repair, protection for high temperature service, fugitive emission monitoring for early leak detection, positive displacement. It also can be used as a high-tech stem extension. See Tech Bulletin Page 0. Fugitive Emission Top Bonnet Design www.flotite.com
Product Identification Code for Complete Valve Model Numbers Tech Bulletin Page 65- Model Full Port: F50 F Red. Port: SF50 SF Material 36SS WCB SS CS C R R 50/50 UHMWPE PEEK Cavity Filled METAL Seat Seal Seal Operator Size F Y X T R S U P C M C R R 50/50 UHMWPE GRAPHITE F Y X T R S U G R R 50/50 UHMWPE PEEK GRAPHITE F X T R S U P G Lever Locking Oval Locking GEAR Deadman Actuator Bare Ordering Information when placing an order or requesting a quotation, please provide as many details on the application as possible such as media type, temperature, pressure, pipe size and etc. L /2 3/ O / G /2 S 2 A 2/2 N 3 6 0 2 5 20 25 32 0 50 65 0 00 50 250 Material Identification Flo-Tite s marking system follows MSS SP-25- guidelines. In addition to the casted body information, we have decided to add metal name plates that identify all valve soft parts. Valve users worldwide will be able to contact Flo-Tite quickly for any installation or service requirements as the company website address will be on all valves. Ordering Examples by Part Numbers Model Reduced Port Class 50 SF50 Seat Material Seal Seal Operator Size Special Feature Stainless Media 36 GRAPHITE LEVER 2 Containment Stainless F G F L 50 H3 36 Flanged Valves with Cryogenic Extension Optional - Special Design Valves Vacuum Service Suitable to 20 Micron Specially cleaned and lubricated valves can handle services of 0-3 mm of Hg ( micron) Flo-Tite offers cryogenic flanged valves. See tech bulletin page. Flanged Valve with Fusible Link Flo-Tite offers flanged valve with fusible link. See tech bulletin page 26. Flanged Valve in Control Valve Service Flo-Tite offers modulating V-port control valves. The V-ball is characterized to meet all custom flow requirements. See tech bulletin page 20. V-ports 5, 30, 60, 0 deg V & slotted balls. Flo-Tite Ball Valves, serving multi-national end users in a wide range of applications in many industries including: Chemical & petrochemical Power generation plants Ship building industries Fiber industries Food industries LNG, HRSG industries Oil refinery industries Desalination industries & iron industries Pulp & paper plants Coal & mining industries Higher Presure HVAC Applications Specific descriptions, dimensions and construction details illustrated may vary slighly from this bulletin. They arefor general use only. We reserve the right to revise or modify product design without prior notice. Flo-Tite, Inc. P.O. Box 23 Tel: (0) 3-0 305 East 2st Street Lumberton, NC 235 Fax: (0) 3-2 Lumberton, NC 235 Website:www.flotite.com E-mail: flotite@nc.rr.com This brochure is general in nature and manufacturer reserves the right to alter dimensions, materials or to make design improvements