Low Pressure FITTINGS & CONNECTORS Dimensions for /4-8 Upchurch Scientific eliminate the need to flange. This removable and reusable system provides several benefits: (pages 58 and 59) Convenience: Our are easy to replace. Just slip the nut and ferrule over the and finger tighten the assembly into your receiving port. In our tests we have shown that the ideal amount of torque to achieve expected part performance should be approximately 3 4 in*lbf (.34.45 N*m). Check out our new P-9, a special tightening tool designed to adapt to many standard torque wrenches, on page. Nuts Minimal Down-Time: Component replacement is quick, taking only a few seconds unlike the significant time required to flange..48 Cost-Effectiveness: Repairing a flanged assembly requires a costly flanging tool or the purchase of a complete replacement assembly, including a new length of and a set of fittings. The system typically requires only one new ferrule at minimal cost. Standard XP-0 XP-06 XP-0 XP-30 XP-38 XP-45 XP-45B XP-30 XP-306 Our /4-8 for /6 and /8 OD are summarized on this page and listed on pages 58 and 59. For our Metric and Large Bore, please refer to pages 60 and 63, respectively. XP-30 XP-330 XP-338 XP-345 Our Flangeless Nuts provide fingertight convenience no wrenches required. Extra-Long Threaded XP-0.6.0 Headless XP-86 XP-386.30.6.3.46 The Convenience of :.6 Short XP-08 XP-8 XP-35 XP-308 XP-335 Please : For Low Pressure MXX Valves, please see page 86..6 FlushNuts XF-358 XF-368 Short Headless XP-83 XP-348 Ferrules Our Flangeless Ferrules provide a leak-proof seal. There is no need to spend time flanging...8 Flangeless Ferrule Pressure Ratings: P-00,500 psi (7 bar) for /6 OD Tubing PEEK Tubing 3,000 psi (07 bar) (using a P-0 Delrin Nut) Stainless Steel Tubing,00 psi (5 bar) P-40,600 psi (79 bar) for /6 OD Tubing PEEK Tubing,500 psi (7 bar) (using a P-0 Delrin Nut) Stainless Steel Tubing,800 psi (93 bar) P-300,900 psi (3 bar) for /8 OD Tubing PEEK Tubing 600 psi (4 bar) P-340 3,000 psi (07 bar) for /8 OD Tubing PEEK Tubing 600 psi (4 bar) (using a P-30 Delrin Nut) Stainless Steel Tubing,00 psi (83 bar) (using a P-30 Delrin Nut) These tests were performed at room temperature with water testing the fitting, NOT the. The material of the nuts, ferrule, and port can affect your results. ORDER 800.46.09 360.679.58 www.idex-hs.com Standard /6 P-00 P-00N P-00R P-.7.9.5.9 Small Valve /6 P-40 Standard /8 P-300 P-300N.4.9 Small Valve /8 P-340 Why did some part numbers change New for 009/00, Upchurch Scientific has combined each of the in this chapter with the most popularly used Flangeless Ferrules for easy ordering convenience. Each of the fittings can still be ordered separately simply remove the preceding letter X from the part number to reference the separate threaded fittings. 57
Low Pressure FITTINGS & CONNECTORS for /6 OD Tubing wide variety of materials and geometries to fit most applications NEW for 009/00 fittings and ferrules packaged together for easy ordering convenience P-00 P-00N P-00R ETFE Gas Ferrule The Upchurch Scientific are excellent replacements for flanged fittings. are dependable, easy to use and easy to replace. Sealing Ring All nuts on this page have /4-8 threads (except XLT-, which has 0-3 threads). Additionally, all fittings on this page come pre-packaged with appropriate ferrules (/4-8 threaded fittings are packaged with P-00 ferrules; however, the XLT- a 0-3 threaded fitting is packaged with P-40 ferrules). Nuts are available in a wide variety of materials, and replacement ferrules are available in ETFE and polypropylene. Please refer to our website, www.idex-hs.com for polymer chemical compatibility information. P- Polypropylene Ferrule P-40 ETFE Small Valve Ferrule XF-358 Stainless Steel FlushNut * XP-0 Delrin Nut * XP-35 PEEK Nut * Other Innovations * Includes P-00 Flangeless Ferrule (shown above). 58 For tight-space applications, try our FlushNut Fittings and Tightening Tools see page for more information. For low-pressure valves with shallow receiving ports, try our P-40 ferrule. For gas applications, try our P-00R ferrule that features an enhanced sealing surface or try one of our VacuTight or Super Flangeless Fittings (pages 6 and 3, respectively). Nut Tightening Tools Use the P-98, P-99 or P-399 Flangeless Nut Extender Tool to tighten any standard, short or extra long style nuts in hard-to-reach places. For headless nuts, use the P-97 Tool. These tools can be used to tighten any of the knurl-headed nuts on pages 58 63 (except as noted on page 6, and XU-60, XU-655 and XU-66 on page 63). They can also be used with many of the high pressure nuts please see page for more information. The F-346 is for tightening /4-8 FlushNut Fittings. F-346 P-99 P-98 P-97 P-399 ORDER 800.46.09 360.679.58 www.idex-hs.com Please see page 57 for the dimensions of the products on this page. Please : The nuts can be ordered separately simply remove the preceding X from the part number to reference the nut separate from the pre-packaged ferrules. Flangeless Ferrules for /6 OD Tubing P-00x Flangeless Ferrules Blue ETFE 0-pk $.45 P-00Nx Flangeless Ferrules Natural ETFE 0-pk.45 P-00Rx Flangeless Ferrules Red ETFE 0-pk 3.5 P-x Flangeless Ferrules Natural Polypropylene 0-pk.45 P-40x Small Valve Flangeless Ferrules Natural ETFE 0-pk.45 /4-8 Flangeless fittings for /6 OD Tubing* XF-358x Flangeless FlushNuts Stainless Steel 0-pk $ 06.4 XLT-x Flangeless Nuts, 0-3 Natural PEEK 0-pk 39.43 XP-0x Flangeless Nuts Black Delrin 0-pk.76 XP-0x Flangeless Nuts Red Delrin 0-pk.76 XP-03x Flangeless Nuts White Delrin 0-pk.76 XP-04x Flangeless Nuts Cream Delrin 0-pk.76 XP-05x Flangeless Nuts Green Delrin 0-pk.76 XP-06x Flangeless Nuts Blue Delrin 0-pk.76 XP-08x Short Flangeless Nuts Black Delrin 0-pk.76 XP-0x Extra Long Flangeless Nuts Blue ETFE 0-pk 7.5 XP-8x Short Flangeless Nuts Natural ETFE 0-pk 7.5 XP-8BLKx Short Flangeless Nuts Black ETFE 0-pk 7.5 XP-0x Flangeless Nuts Natural Polypropylene 0-pk.76 XP-30x Flangeless Nuts Natural PEEK 0-pk 36.63 XP-35x Short Flangeless Nuts Natural PEEK 0-pk 36.63 XP-38x Flangeless Nuts Purple Delrin 0-pk.76 XP-45x Flangeless Nuts Natural Teflon PFA 0-pk 7.5 XP-45Bx Flangeless Nuts Blue Teflon PFA 0-pk 7.5 XP-83x Short Headless Flangeless Nuts Natural PEEK 0-pk 36.63 XP-86x Headless Flangeless Nut Natural PPS 0-pk 3.8 Nut tightening tools F-346 FlushNut Tool for /4-8 Nuts $ 7.9 New! P-9 For Standard Head Nuts with /4 Hex Drive, Aluminum** 4.69 P-97 Flangeless Nut Extender Tool for Headless Style Nuts, Aluminum 0.4 P-98 Flangeless Nut Extender Tool for Standard Head Nuts, Delrin 6.73 P-99 Flangeless Nut Extender Tool for Standard Head Nuts, Aluminum 3.50 P-399 Flangeless Nut Extender Tool for Standard Head Nuts, Short, Aluminum 3.50 * Other color choices are available for several of these nuts. Please contact us for more information. ** For easy coupling with torque wrench. Packaged with ten (0) P-00 ferrules. Packaged with ten (0) P-40 ferrules, the only Ferrule that can be used with this Fitting.
Low Pressure FITTINGS & CONNECTORS for /8 OD Tubing wide variety of materials and geometries to fit most applications NEW for 009/00 fittings and ferrules packaged together for easy ordering convenience P-300 P-300N P-340 ETFE Small Valve Ferrule Upchurch Scientific for /8 OD feature a wide assortment of nut geometries and materials from which to choose. Each of our Fittings shown on this page comes in convenient 0-packs and also includes P-300 Flangeless Ferrules. (The nuts can be ordered separately simply remove the preceding X from the part number to reference the nut separate from the pre-packaged ferrules.) All nuts on this page have /4-8 threads. Nuts for M6 threaded ports are on page 60. XF-368 Stainless Steel FlushNut* XP-305 Delrin Nut* XP-335 PEEK Nut* Please : For Low Pressure MXX Valves, please see page 86. XP-386 PPS Nut* *Includes P-300 Flangeless Ferrule (shown above). Please see page 57 for the dimensions of the products on this page. The P-340 ferrule is designed for use with shallow receiving ports, such as those used on some low pressure valves. our XF-368 FlushNut is an excellent choice for applications where port-to-port spacing is limited; see page for more information on this innovative product line. As an alternative, consider one of the headless fittings shown on this page. Lock Nut The P-3 Lock Nut is for use with any /4-8 male Flangeless Fitting. Use this product in applications where vibrations can loosen fittings. To Use: Thread the lock nut onto the male fitting. When the male fitting is firmly seated into the receiving port, tighten the lock nut down against the receiving port to securely hold the male fitting in place. P-3 Lock Nut White Delrin Other Innovations The Flangeless SealTight Fittings system holds to 5,000 psi (345 bar) in a flat-bottom port. See page. super Flangeless Fittings on pages 4 hold to high pressures and prevent twist. VacuTight Fittings are designed to improve transfer volume consistency in gas and liquid handling systems. See page 6. our Frit-In-A-Ferrule seals and filters simultaneously. See page 3. Capillary Connections connect capillary-sized to /4-8 or M6 flat-bottom ports using our Super on page 3 and 4, along with NanoTight Sleeves on page 40. ORDER 800.46.09 360.679.58 www.idex-hs.com Flangeless Ferrules for /8 OD Tubing P-300x Flangeless Ferrules Yellow ETFE 0-pk $.45 P-300Nx Flangeless Ferrules Natural ETFE 0-pk.45 P-340x Small Valve Ferrules Natural ETFE 0-pk.45 /4-8 Flangeless FITTINGS for /8 OD Tubing* XF-368x Flangeless FlushNuts Stainless Steel 0-pk $ 06.4 XP-30x Flangeless Nuts Black Delrin 0-pk.76 XP-30x Flangeless Nuts Red Delrin 0-pk.76 XP-303x Flangeless Nuts White Delrin 0-pk.76 XP-304x Flangeless Nuts Cream Delrin 0-pk.76 XP-305x Flangeless Nuts Green Delrin 0-pk.76 XP-306x Flangeless Nuts Blue Delrin 0-pk.76 XP-308x Short Flangeless Nuts Black Delrin 0-pk.76 XP-35x Flangeless Nuts Natural ETFE 0-pk 7.5 XP-30x Flangeless Nuts Natural Polypropylene 0-pk.76 XP-330x Flangeless Nuts Natural PEEK 0-pk 36.63 XP-335x Short Flangeless Nuts Natural PEEK 0-pk 36.63 XP-338x Flangeless Nuts Purple Delrin 0-pk.76 XP-345x Flangeless Nuts Natural PFA 0-pk 7.5 XP-348x Short Headless Flangeless Nuts Natural PEEK 0-pk 36.63 XP-386x Headless Flangeless Nut Natural PPS 0-pk 3.8 Lock Nut for Flangeless Nuts P-3x Lock Nut for Flangeless Nuts White Delrin 0-pk $ 3.06 * Other color choices are available for several of these nuts. Please contact us for more information. Packaged with ten (0) P-300 ferrules. 59
Low Pressure FITTINGS & CONNECTORS 60 Metric P-343 for 3.0 mm OD For /6,.8 mm,.0 mm,.5 mm, 3.0 mm, 4.0 mm and /8 OD Tubing delrin, PFA, PPS and PEEK Nuts Tefzel (ETFE) and Kel-F (PCTFE) Ferrules Upchurch Scientific Metric Flangeless Ferrules are designed to connect.8,.0,.5, 3.0 and 4.0 mm OD to flat-bottom ports when paired with the appropriate M6, /4-8 or 5/6-4 Flangeless Nuts. We also offer M6-threaded nuts to connect /6 and /8 OD, plus a sleeve to facilitate.0 mm OD connections. Please refer to the Metric Connections chart on this page for information regarding which nuts and ferrules to use with your. F-5 Tubing Sleeve for.0 mm OD shown with P-00 Ferrule (page 58) P-88 PPS Nut for /6 OD.46 P-34 for.8 and.0 mm OD P-39 Kel-F Ferrule for 4.0 mm OD The dimensions shown apply to P-07, P-6, P-307 and P-36. The dimensions shown apply to P-07S, P-47, P-307S and P-347. P-07 Delrin Nut for /6 OD.6.6 P-347 PEEK Nut for.8,.0, 3.0 mm and /8 OD P-353 for.5 mm OD More Metric Sized Products:.3 P-36 PEEK Nut for.8,.0, 3.0 mm and /8 OD.39 Page High Pressure Polymer Fittings 7, 3, 4, 44 High Pressure Stainless Steel Fittings 9 Luer Adapters 49 Metric Threaded Adapters 54 External NPT Adapters 55 VacuTight Fittings 6 Plugs and Caps 6 Low Pressure Unions 64 Bulkhead Unions 65 PEEK (.8 mm OD and Capillary) and Fused Silica Tubing 68, 69 PEEKsil Tubing 70 FEP Tubing (.0 4.0 mm OD) and PFA Capillary Tubing 73, 74 Frit-In-A-Ferrule 3 In addition, many of our /4-8 threaded Filters, Valves and Flow Control Accessories can be converted to accept.8,.0,.5 and 3.0 mm, using the ferrules listed for /4-8 ports in the Metric Connections table, above right. ORDER 800.46.09 360.679.58 www.idex-hs.com Metric Connections: Use this chart to determine the low pressure fittings needed to connect metric and English-sized into the indicated ports. Tubing Size Port Ferrules Nuts.0 mm M6 P-00 P-07, P-07S, P-6, P-47, P-88 /4-8 P-00 Any /4-8 nut from page 58.8 mm M6 P-34 P-307, P-307S, P-36, P-347, P-36 /4-8 P-34 Any nut from page 59.0 mm M6 P-363R P-307, P-307S, P-36, P-347, P-36 /4-8 P-363R Any nut from page 59.5 mm M6 P-353 P-307, P-307S, P-36, P-347, P-36 /4-8 P-353 Any nut from page 59 3.0 mm M6 P-343 P-307, P-307S, P-36, P-347, P-36 /4-8 P-343 Any nut from page 59 4.0 mm 5/6-4 P-39 XP-3x, XP-38x from page 63 /6 M6 P-00 P-07, P-07S, P-6, P-47, P-88 M6 P-840 P-93, P-933, P-935 from page 6 /8 M6 P-300 P-307, P-307S, P-36, P-347, P-36 M6 P-940 P-943, P-945, P-947 from page 6 * With F-5 Tubing Sleeve. To order /4-8 threaded Flangeless Nuts separately from the Flangeless Ferrules, simply remove the preceding X from the appropriate part number for example, order P-0x instead of XP-0x. Metric Ferrule Pressure Ratings: Metric Flangeless FITTINGS for.0 mm & /6 OD Tubing F-5x Tubing Sleeves, /6 OD for.0 mm only Purple FEP 0-pk $ 0.06 P-00x Flangeless Ferrules Blue 0-pk.45 P-07x Flangeless Nuts, M6 Black Delrin 0-pk.45 P-07S Short Flangeless Nut, M6 Black Delrin ea..0 P-6x Flangeless Nuts, M6 Black PFA 0-pk 7.3 P-47x Short Flangeless Nuts, M6 Black PEEK 0-pk 7. P-88 Headless Flangeless Nut, M6 Black PPS ea..4 Metric for.8,.0,.5, 3.0, 4.0 mm & /8 OD Tubing P-39 Flangeless Ferrule for 4.0 mm only Natural Kel-F ea. $ 3.5 P-300x Flangeless Ferrules Yellow ETFE 0-pk.45 P-307x Flangeless Nuts, M6 Black Delrin 0-pk.45 P-307S Short Flangeless Nut, M6 Black Delrin ea..0 P-36x Flangeless Nuts, M6 Black PFA 0-pk 7.3 P-34x Flangeless Ferrules for.8-.0 mm only Green ETFE 0-pk.45 P-343x Flangeless Ferrules for 3.0 mm only Orange ETFE 0-pk.45 P-347x Short Flangeless Nuts, M6 Black PEEK 0-pk 7. P-353x Flangeless Ferrules for.5 mm only Natural ETFE 0-pk.45 P-36x Short Headless Flangeless Nuts, M6 Black PEEK 0-pk 7. P-363Rx Flangeless Ferrules for.0 mm only Red ETFE 0-pk.45 Use P-39 with 5/6-4 nuts only (XP-3x or XP-38x on page 63). Polymer Tubing.0 mm OD Tubing FEP 500 psi (34 bar)* P-00 Flangeless Ferrule (using a P-07 Delrin Nut, F-5 Tubing Sleeve).8 mm OD Tubing PEEK,700 psi (7 bar) P-34 Flangeless Ferrule (using a P-30 Delrin Nut).0 mm OD Tubing PEEK,000 psi (69 bar) P-363R Flangeless Ferrule (using a P-307 Delrin Nut).5 mm OD Tubing FEP 650 psi (45 bar) P-353 Flangeless Ferrule (using a P-307 Delrin Nut) 3.0 mm OD Tubing FEP 500 psi (34 bar) P-343 Flangeless Ferrule (using a P-30 Delrin Nut) 4.0 mm OD Tubing FEP 50 psi (7 bar) P-39 Flangeless Ferrule (using a P-3 PEEK Nut) These tests were performed at room temperature with water testing the fitting, NOT the. The material of the nut, ferrule, and port can affect your results. *For higher pressures, use a Super Flangeless Nut and Ferrule from page or 3 with this sleeve.
VacuTight Fittings Low Pressure FITTINGS & CONNECTORS VacuTight Fittings and Union For /6 and /8 OD Tubing 0-3, /4-8 and M6 Threads improve Transfer Volume Consistency Upchurch Scientific VacuTight Fittings are designed to provide airtight, dependable connections under vacuum and low pressure conditions. Many of the VacuTight Nuts have streamlined profiles for use in systems requiring a large number of connections in a small area. Furthermore, the VacuTight Ferrule s small size ensures sufficient nut/thread engagement, even in shallow ports. These features make VacuTight Fittings ideal for combichem, high throughput screening, clinical diagnostic and other automated liquid handling applications. VacuTight Fittings are available for flat-bottom 0-3, /4-8 and M6 threaded ports. The configuration of the VacuTight flat-bottom ferrules prevents overcompression and ID reduction that can occur with many coned fittings. The result is more consistent aspirating and dispensing volumes across all system connections. The 0-3 VacuTight Fittings are for use with /6 OD. The /4-8 and M6 fittings are available for use with both /6 and /8 OD. All VacuTight Nuts must be used exclusively with VacuTight Ferrules. VacuTight Nuts with hex heads can be tightened with a standard /4 wrench. All VacuTight Nuts with knurls (finger grip ridges) can be tightened finger tight. Additionally, some of the standard head and headless nuts can be tightened with our Extender Tools (see page 58). We recommend tool tightening no more than a / turn past finger tight. Use any of the 0-3 fittings on this page to make an inline connection with our VacuTight Union. This product is designed for use with /6 OD. Or, use your choice of /4-8 or M6 VacuTight Fittings with the appropriate union from page 64 to make an inline connection with /6 or /8 OD..76 P-845-0 PEEK Union (0-3 internal threads) Vacuum and Pressure Rating Table, : Vacuum Pressure Tubing Rating Rating P-840 VacuTight Ferrule PFA,.00 ID 5 in. Hg 400 psi (7 bar) for /6 OD Tubing ETFE,.00 ID 5 in. Hg 800 psi (55 bar) (using a P-938 PEEK Nut) P-940 VacuTight Ferrule PFA,.06 ID 5 in. Hg 500 psi (34 bar) for /8 OD Tubing ETFE,.06 ID 5 in. Hg,000 psi (69 bar) (using P-948 PEEK Nut) This chart is intended for reference only and refers to the pressure rating of the fittings, NOT the. Tests were conducted with room temperature water as the solvent. Your results may vary depending on nut, port and materials, actual diameters (with manufacturer s tolerances), chemical compatibility, etc. The nuts were finger tightened for these tests. In some cases, improved results can be obtained by using the tools mentioned above. ORDER 800.46.09 360.679.58 www.idex-hs.com P-945 Delrin Nut, M6 with P-940 Ferrule.60 P-84 PEEK Nut, 0-3 P-847 PEEK Nut, 0-3.6.38.0.70 VacuTight Ferrules P-840x VacuTight Ferrules for /6 OD, Red ETFE 0-pk $.4 P-940x VacuTight Ferrules for /8 OD, Red ETFE 0-pk.4 VacuTight Nuts for /6 OD (Each includes 0 P-840 Ferrules) P-84x Short Hex Head Nuts, 0-3, Red PEEK 0-pk $ 45.00 P-844x Short Headless Nuts, 0-3, Red PEEK* 0-pk 45.00 P-846x Long Headless Nuts, 0-3, Red PEEK* 0-pk 45.00 P-847x Long Hex Head Nuts, 0-3, Red PEEK 0-pk 45.00 P-848x Long Knurl/Hex Fathead Nuts, 0-3, Red PEEK 0-pk 45.00 P-930x Stnd. Length Stnd. Head Nuts, /4-8, Red Delrin* 0-pk 45.00 P-93x Stnd. Length Stnd. Head Nuts, M6, Red Delrin 0-pk 45.00 P-93x Short Stnd. Head Nuts, /4-8, Red Delrin 0-pk 45.00 P-933x Short Stnd. Head Nuts, M6, Red Delrin 0-pk 45.00 P-934x Stnd. Length Headless Nuts, /4-8, Red Delrin 0-pk 45.00 P-935x Stnd. Length Headless Nuts, M6, Red Delrin 0-pk 45.00 P-938x Stnd. Length Stnd. Head Nuts, /4-8, Natural PEEK* 0-pk 45.00 VacuTight Nuts for /8 OD (Each includes 0 P-940 Ferrules) P-94x Stnd. Length Stnd. Head Nuts, /4-8, Red Delrin* 0-pk $ 45.00 P-943x Stnd. Length Stnd. Head Nuts, M6, Red Delrin 0-pk 45.00 P-944x Short Stnd. Head Nuts, /4-8, Red Delrin 0-pk 45.00 P-945x Short Stnd. Head Nuts, M6, Red Delrin 0-pk 45.00 P-946x Stnd. Length Headless Nuts, /4-8, Red Delrin 0-pk 45.00 P-947x Stnd. Length Headless Nuts, M6, Red Delrin 0-pk 45.00 P-948x Stnd. Length Stnd. Head Nuts, /4-8, Natural PEEK* 0-pk 45.00 VacuTight union with 0-3 threads Swept Volume P-845-0 PEEK Union for /6 OD Tubing, Red.0 µl $.45.00 (.50 mm) thru-hole.60 P-844 PEEK Nut, 0-3.45 P-848 PEEK Nut, 0-3.96.5 P-946 3 Delrin Nut, /4-8 with P-940 Ferrule.48 The dimensions shown apply to P-930, P-93, P-938, P-94, P-943 and P-948. The dimensions shown apply to P-93, P-933, P-944 and P-945. 3 The dimensions shown apply to P-934, P-935, P-946 and P-947. * These nuts can be tightened with our Extender Tools (see page 58)..0.70 P-846 PEEK Nut, 0-3.48 P-930 Delrin Nut, /4-8 6
Low Pressure FITTINGS & CONNECTORS Flanged Fittings, Plugs and Caps 6 Flanged Fittings interchangeable with Cheminert and Omnifit Fittings Upchurch Scientific /4-8 Flanged Fittings are compatible with most standard flanged fittings. The hard, inert Delrin (acetal resin) nut resists cross threading or loosening during use, while the Tefzel (ETFE) nuts work well in chemically aggressive environments. The nuts are interchangeable with Cheminert and Omnifit fittings. Each color-coded Flanged Fitting is shipped with a stainless steel washer to ensure a good seal and firm connection in any flat-bottom port. For an alternative to flanging, we highly recommend the Flangeless Fittings found on pages 57 59, the Super Flangeless Fittings found on pages 4, or the VacuTight Fittings on page 6..3 P-40 Flanged Fitting for /6 OD *.64.40.3.64.40 P-580B Flanged Fitting for /8 OD * The dimensions shown apply to all square-head Flanged Fittings The dimensions shown apply to all hex-head Flanged Fittings 3 The dimensions shown apply to all knurled-head Flanged Fittings *Flanged not included Plugs and Caps For Coned and Flat-Bottom Ports.64.40 P-48G 3 Flanged Fitting for /6 OD * seal 0-3, /4-8, M6 and 5/6-4 Threaded Ports or Fittings Use Upchurch Scientific plugs to close off unused ports in valves and multi-port connectors. Our color-coded 0-3 threaded plugs are perfect for identifying stored columns that have different packing materials, or in which different mobile phases have been utilized. Cap off with one of the ETFE caps presented on this page and the appropriate fittings from this chapter or the High Pressure chapter (starts on page 3). To help determine which plug or cap is best suited for your application, please visit www.idex-hs.com for detailed chemical compatibility data..85.49 P-36 PFA Plug for /4-8 flat-bottom ports ORDER ONLINE www.idex-hs.com.36.69.49 U-467R Delrin Column Plug for 0-3 coned ports.45 P-755 ETFE Cap for /4-8 flat-bottom fittings ORDER 800.46.09 360.679.58 www.idex-hs.com Flanged Fittings, /4-8 For /6 OD For /8 OD Head Style Color/Material P-40x P-50x Square Black Delrin 0-pk $ 5.34 P-40x P-50x Square Red Delrin 0-pk 5.34 P-403x P-503x Square White Delrin 0-pk 5.34 P-404x P-504x Square Cream Delrin 0-pk 5.34 P-405x P-505x Square Green Delrin 0-pk 5.34 P-406x P-506x Square Blue Delrin 0-pk 5.34 P-508x Square Gray Delrin 0-pk 5.34 P-480B P-580B Hex Blue Delrin ea..58 P-480BLK P-580BLK Hex Black Delrin ea..58 P-480C P-580C Hex Cream Delrin ea..58 P-480G P-580G Hex Green Delrin ea..58 P-580GRY Hex Gray Delrin ea..58 P-480R P-580R Hex Red Delrin ea..58 P-480T P-580T Hex Natural ETFE ea..63 P-480W P-580W Hex White Delrin ea..58 P-48B P-58B Knurled Blue Delrin ea..58 P-48BLK P-58BLK Knurled Black Delrin ea..58 P-48C P-58C Knurled Cream Delrin ea..58 P-48G P-58G Knurled Green Delrin ea..58 P-48R P-58R Knurled Red Delrin ea..58 P-48T P-58T Knurled Natural ETFE ea..63 P-48W P-58W Knurled White Delrin ea..58 P-407x P-507x Stainless Steel Washers 0-pk 5.36 Plugs Color/Material P-0 For /4-8 coned ports 3 Natural Kel-F ea. $ 7.76 P-3 For /4-8 flat-bottom ports 4 Natural ETFE ea..90 P-309x For /4-8 flat-bottom ports Black Delrin 0-pk.45 P-3 For /4-8 flat-bottom ports Natural ETFE ea..78 P-34 For M6 flat-bottom ports Black ETFE ea..78 P-34N For M6 flat-bottom ports Natural ETFE ea..78 P-36 For /4-8 flat-bottom ports Natural Teflon PFA ea..83 P-3 For /4-8 flat-bottom ports 5 Natural PEEK ea..03 P-50 For 0-3 coned ports 4 Stainless Steel ea. 8.67 P-550 Extra Long for 0-3 coned ports Natural PEEK ea..4 P-55 For 0-3 coned ports Natural PEEK ea..4 P-556 For 5/6-4 flat-bottom ports 4 Natural PEEK ea. 7.39 P-557 For 5/6-4 flat-bottom ports 4 White Delrin ea..56 P-849 For 0-3 flat-bottom ports Black Delrin ea. 4.6 U-467Bx For 0-3 coned ports Blue Delrin 0-pk 7.46 U-467BLKx For 0-3 coned ports Black Delrin 0-pk 7.46 U-467DBx For 0-3 coned ports Dark Blue Delrin 0-pk 7.46 U-467Rx For 0-3 coned ports Red Delrin 0-pk 7.46 U-467Wx For 0-3 coned ports White Delrin 0-pk 7.46 U-468Bx For 0-3 coned ports Blue ETFE 0-pk 9.7 U-468BLKx For 0-3 coned ports Black ETFE 0-pk 9.7 U-468Nx For 0-3 coned ports Natural ETFE 0-pk 9.7 Caps TOP SELLER see starred products in price block. Color/Material P-754 For use with 0-3 coned fittings Yellow ETFE ea. $.4 P-755 For use with /4-8 flat-bottom fittings Black ETFE ea..4 P-756 For use with M6 flat-bottom fittings Blue ETFE ea..4 Each Flanged Fitting comes with the appropriate Stainless Steel Washer. The size of for which the fittings in the column are designed. 3 For /8 OD. 4 Hex head (5/6 ). 5 FlushNut style. Use a flat-head screwdriver or our F-346 Tool on page 58 to tighten.