INSTALLATION GUIE GVM5 SELF SUPPORTING STAN FOR 0-0 OGE HARGER STRONG RELIALE SEURE 00.0.0
THESE OMPONENTS ARE REQUIRE TO INSTALL THE PRO-GAR GVM5 SELF SUPPORTING STAN AN TRI-LOK GUN RAK G5-0 MOUNT ASE Tri-Lock Gun Rack GVPMXXXX I. Refer to the diagram on the last page of these instructions to verify all parts were received. II. The following tools will be required to complete the installation. A. / Socket & Ratchet. / Allen Wrench. 5/ Allen Wrench. / Socket III. Installing the self supporting stand. A. Losen the inner rear seat track bolts for the passenger and driver front seat. NOTE: It unneccassary to remove the bolts completly.. Orient the Mounting ase (G5-0) so that the legs face towards the front of the vehicle. Slide the legs of the base under the front seat tracks, aligning the nothes with the Seat bolts and alingment pins. Leave loose. (See Fig. ). Using the supplied Self Tapping Screws (X5) ancor the rear of the Mounting base to the Rear Seat Area.. Tighten the OEM Front Seat olts. Note: No torque spec reqiured. FIG. PASSENGER SIE SHOWN IV. ase Installation omplete (ontinue with The Gun Rack Installation) OEM SEAT OLT FORWAR OEM SEAT RAIL 00.0.0
V. Installing the Tri-Lock gun rack (Requires Pro-gard self-supporting mounting base) A. Place the intended guns into the gun rack and make adjustments to fit. This will allow more access than when the rack is in the vehicle, but the rack can be adjusted after installed inside the vehicle as well.. The brackets mounting the gun lock are designed to be loosened and adjusted in many directions to accomodate most guns. Fit each gun by loosening the bolts on the gun lock bracketry so the mounting bracket moves freely. Place your gun into the lock and in the desired position. Take a allen wrench to tighten locks in place. (See Fig. ) Locks move up and down Tilts clockwise or counter clockwise ompleted Gun Fitment The shot gun shown in the lower position with insert Left and right Fig. Gun locks should open and close easily and guns should pull in and out of the rack with no issues when properly installed. Shot Gun Mounting - The shot gun can be mounted in two ways, by barrel mount or by installation of the shot gun mount insert. To install the shot gun insert, remove the standard insert by opening the lock and unscrewing the two insert bolts with an allen wrench. Remove the retaining ring from the bolt s back side. Replace with shot gun insert (G) and reinstall insert bolts and retaining rings on the back side of the insert. Use the two fastener bolt s adjustment to fit the shot gun used in the lock. (See Fig. ) A Step Remove barrel bracket Step Remove standard insert Step Replace with shot gun insert A arrel mounting bracket Fig. Standard insert Shot gun insert Retaining ring 00.0.0
VI. Self-Supporting Installation A. For self-supporting installations, remove the four bolts that secure the butt plates to the base of the gun rack. Then rest the gun rack to the self supporting stand, loosely attach the gun rack and adjust it and the butt plates as necessary from front to back. (See Fig. ) NOTE: For Optimal onditions secure the back of the gun rack tigth against the seat. VII. Lock ox A. Open the lock box and loosen the bolts with a / socket and extension wrench to adjust the box up or down as needed. (Swivel attachment is required) Install supplied black felt over bolts when box position has been fixed. (See Fig. 5) Adjustable hole locations to provide the best mounting preference. Lock box adjustment bolts Fig. Fig. 5 00.0.0
VIII. Gun lock switch and timer installation. A. We suggest mounting the momentary release button in a concealed location that can be easily reached by the officer, but would be hidden in case an unathorized entry occurs.. onnect the gun lock wiring as shown in the diagram below. NOTE: Pro-gard requires the use of a 0 AMP fuse between the power source and gun lock circuit or the warranty will be voided! IX. Lock Head Operating Instructions Fig. A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.. While depressing and holding the release button (momentary switch), push and then pull the weapon towards the lid of the gun lock to release it from the lock. NOTE: TIP: One handed operation is possible utilizing the optional second timer. The timer will unlock the lock for seconds following activation of the momentary switch. If the gun is not pulled out of the lock within seconds after activation of the momentary switch, the lock will automatically re-lock. If lid of the lock does not release, press in on the lid to release tension and reactivate the release button (unless timer is still active). Installation omplete! all Pro-gard technical support if assistance is needed. -00-0-0 00.0.0 5
Self-Supporting Mounting ase G5-0 PART NUMER ESRIPTION G5-0 SELF SUPPORTING ASE G50 SELF SUPPORTING LEG, LEFT G50 SELF SUPPORTING LEG, RIGHT HARWARE KIT PART NUMER ESRIPTION X5 / X " SELF RILLING HEX HS 00.0.0
Tri-Lock Gun Rack PARTS LIST PART NUMER ESRIPTION GVM0-0 RAK ASE WELMENT * GVM00-0 **G-00.5" X.5" X " LG. ALUM EXTRUSION UTT PLATE - LAK NYLON * **G-00 RUER UTT PLATE PA 5 * GVM0-0 LOK MOUNTING RAKET - PASSENGER * GVM0-0 LOK MOUNTING RAKET - RIVER * * **G0-NPG **G5 G00 R GUN LOK R LOK ARREL MOUNT RAKET UPPER PARTITION MOUNTING RAKET A 5 5 5 5 5 0 0 5 5 0 5 0 5 0 * * * G0 LOWER PARTITION MOUNT RAKET (NOT SHOWN) G LOK INSERT FOR SHOT GUN PART NUMER GL0 GUN SAFE GVM0-0 HARWARE LIST GVM00-0 PART NUMER ESRIPTION X 5/- X / SHS, K G-00 X / FLAT WASHER, LAK G-00 X5 /-0 X 0.5 SHS 5 GVM0-0 X5 /-0 SLOT NUT (NOT SHOWN) X / FLAT WASHER, LAK GVM0-0 X /-0 x " HHMS, Zn G0-NPG X /-0x0.5, SHS, LAK OXIE G5 X /-0 X / ARRIAGE OLT XZ /-0 WHIZ NUT G00 050-PLAIN EXTRUSION EN AP 0 G0 X /-0 WHIZ NUT (NOT SHOWN) G X5 5/- X 0. LG. SHS, K X - SLOT NUT GL0 N00-TH NEOYMIUN MAGENT X - X 5/ FHSS PART NUMER X /-0 X 0.5 HEX AP SREW X 0.5 RIVET (NOT SHOWN) X G50R LAK FELT /" X " ONSUME (NOT X SHOWNT) G50R-0 LOK OX FELT (NOT 5 SHOWN) G500 MOMENTARY SWITH G00 TIMER ELAY MOULE * - MAY VARY EPENING ON ONFIGURATION ** - MAY VARY EPENING ON ONFIGURATION 0 X5 X5 X X X X XZ A 050-PLAIN 5 5 X X5 X N00-TH X X 5 0 0 0 X G50R G50R-0 A 00.0.0