Altra Industrial Motion Application Guide Clutches
Formsprag Clutches Formsprag Clutch Broadest Range of Clutches With over 50 years of experience, Formsprag has applied catalog standard clutches as well as many special designs (typically driven by OEM requirements) into a wide variety of markets. This has resulted into expanding the product offering into the broadest range of overrunning clutches in the world. Over 2,000 different products are available with catalog designs ranging from 1 to 720,000 lb.ft. of torque capacity, clutch bores from 0.1 inches to over 20.0 inches and overrunning applications operating up to 50,000 RPM in jet engines. Formsprag overrunning clutches can be found in every corner of the world with applications in commercial, aircraft and military equipment. These applications include backstopping clutches in many gear reducers, snow ski lifts, amusement park rides, automotive final assembly lines, steel stamping presses, fan and pump drives, corrugated box making, material handling in foundries and steel making, forming and pickling, and marine applications such as submarines. Formsprag Clutches are available for three basic types of applications:, Indexing, and. Rebuild and Overhaul Service Send us your old clutches and we ll make them like new again. With the same wear life as original products at rebuild cost. The difference is not just cosmetic. All internal components sprags, energized springs, retainer, bearings, seal and hardware are refurbished or replaced to new performance standards. The inner and outer races are ground to specifications noted below so that no wear patterns remain. Sprag Surface is hardened to 58-62 Rc Sprag Surface finish is 15-25 microinches Sprag Surface taper limit is 0.0002 inch per inch Consider these advantages Price A guaranteed savings of at least 30% or more versus new product. Speed Clutches are received, inspected and rebuilt in the shortest possible time frame. Warranty The Model LLH has a 3 year warranty, all other models are 1 year on labor and materials, same as new clutches. Emergency Breakdown Program All products that are air freighted into the Warren plant are processed immediately and, in most cases, are able to be rebuilt within a 24-hour period. However, for applications that can t afford downtime, a spare clutch is recommended. Formsprag s Quality Management System is certified to ISO 9001: 2008 and AS 9100 Rev. D BEFORE AFTER For more information call 1-800-927-3262 2
MARINE LIFTING Bi-Directional TEXTILE PROCESSING FSO overrunning clutches allow the feed drive to power the rollers at a low speed when threading the leading edge of a new roll of fabric. When the fabric is fully threaded and ready to be pulled at production speeds, the FSO un-clutches the feed drive allowing those same rollers to be rotated at faster speeds without back driving the lower speed feed drive. The clutch automatically disconnects the lower speed feed drive during higher speed operation and prevents possible damage to the feed drive if back driven at the higher speeds. Model FL Model FSO Form-Lock (FL) bi-directional clutches are used on winch drives of davits on ships to provide optional manual drive to the normal drive system to smoothly raise and lower the life boats. The Form-Lock is a mechanical clutch that can be driven in both directions while automatically providing a holding brake function when the driving torque is stopped. Additional uses include the smooth raising and lowering of gun barrels in artillery, and other loads being raised and lowered smoothly with ball screws. Contact Formsprag for information and assistance. Torque Range: 100 to 4800 lb.in. (11,3 to 542 Nm) Bore Range: 0.5 to 7.0 in. (12,7 to 177 mm) Model HPI Food Conveyor Indexing Drive Indexing HPI clutches are mounted on the head shaft and translates the reciprocating motion from the crank mechanism into incremental motion in one direction, advancing the conveyor a uniform distance with each drive stroke and then overrunning in the opposite direction on the return stroke. These clutches are available with FDA approved food grade greases and a variety of surface coatings required for wash down duty. Bore Range: 0.5 to 7.0 in. (12,7 to 177 mm) 3
Formsprag Clutches Model FSO ASSEMBLY LINE CONVEYOR FSO overrunning clutch is mounted on the head shaft of a conveyor system to provide instantaneous switching from the primary drive to a stand-by drive to reduce down time. Mounting the FSO clutch between each drive and the conveyor provides the automatic clutching and de-clutching when switching from one drive to another without any utility or input to the clutch. Using the FSO clutch on dual drive applications reduces installation and operating costs by eliminating controls or actuation mechanisms. DUAL DRIVE FW clutch coupling is used on in-line mounting of dual drive systems of fans and pumps to provide a smooth transfer of power from one drive/power system to another (electric motor to steam turbine and gear reducer). The model FW clutch coupling mounted between the output of a steam turbine reducer and the fan allows this fan to be initially started with an electric motor without back driving the steam turbine. When steam becomes available the FW allows the steam turbine drive to come up to speed (over any amount of time) and automatically transfer power. When the speeds are matched, the starting electric motor can be turned off to save its utility cost. Bore Range:.05 to 7.0 in. (12,7 to 177mm) Model FW Bore Range: 0.6 to 7.0 in. (15,9 to 177 mm) Torque Range: 107 to 27,000 lb.ft. (145 to 36720 Nm) Model FWW TWO SPEED CONVEYOR DRIVE FWW clutch coupling is used on inline mounting of creep drive conveyor systems for low speed belt inspections or cold weather low speed weekend creep operation. The FWW clutch coupling is mounted between the main drive and the low speed creep drive and provides for smooth clutching when switching from one drive to the other. Cost savings are realized at both the initial installation because no controls are required to perform the clutching and declutching function; and during operation because no set-up or wear adjustments are required so that regular maintenance costs are reduced. Bore Range:.375 to 3.75 in. (9,5 to 95 mm) Torque Range: 276 to 2,066 lb.ft. 4 (375 to 2800 Nm)
FAN DRIVE LCB clutches can be mounted directly on the shaft of the fan drive and grounded with a torque arm; the unit provides a backstop function for the fan drive. When the fan is turned off, wind flow from other fans in the system or the environment can cause the fan to rotate opposite the operating direction and the LCB can eliminate this problem thereby improving the life of the fan drive systems. Bore Range: 1.855 to 5.00 in. (46,9 to 127 mm) Torque Range: 150 to 850 lb.ft. (200 to 1150 Nm) Model FSR Model LCB PUNCH PRESS FEED DRIVE FSR clutches are used as a backstopping clutch on a press feed drive by mounting the clutch on one end of the drive roller and grounding the outer race with a torque arm. This installation allows the drive roller to rotate in only the desired direction. Press feed rollers for applications using steel and other stiff materials pulling from a coil need to resist the material s natural tendency to spring backwards or re-coil. Bore Range:.3 to 2.19 in. (7,6 to 55,5 mm) Torque Range: 40 to 1,800 lb.ft. (55 to 2448 Nm) Model HSB COOLING TOWER FAN DRIVE HSB (High Speed Backstop) clutches are used on cooling tower fan drives to prevent rotation in the opposite direction from the normal driving direction. When the fan drive is off, wind pressure from other fans or ambient breezes can apply sufficient force to rotate fan blades in the opposite direction. The HSB clutch allows the fan to freely rotate in the desired driving direction while preventing any rotation in the opposite direction. Bore Range:.43 to 7.0 in. (10,9to 177,80 mm) Torque Range: 300 to 27,000 lb.ft. (408 to 36720 Nm) 5
Formsprag Clutches Model LLH BULK HANDLING CONVEYOR DRIVE LLH holdback clutches are mounted on the head shaft of the conveyor, typically on the side opposite the electric motor and gear reducer. The LLH clutch allows the headshaft to freely rotate in the driving direction while preventing any rotation in the opposite direction. Bore Range: 1.87 to 20.0 in. (47,6 to 508 mm) Torque Range: 5,000 to 700,000 lb.ft. (6800 to 952000 Nm) PUNCH PRESS FEED DRIVE Indexing HPI indexing clutches are used on the material feed drive of punch press machines to provide a uniform incremental rotation of the feed rollers with each stroke of the press ram. The reciprocating motion of the gear rack is translated into specific and uniform motion by the HPI clutch, advancing the correct amount of material for the next punch stroke. These clutches are available with either oil or grease lubrication. Model HPI Bore Range: 0.5 to 7.0 in. (12,7 to 177 mm) CONVEYOR DRIVE Model FSO FSO clutches are used on multi-speed, one direction only conveyors for non-destructive accommodation of speed differentials in powered rollers and belt drive systems. The FSO clutch allows the slower speed zone to over-speed during the transitional period without back driving the slower drive system. Bore Range: 0.5 to 7.0 in. (12,7 to 177 mm) 6
HIGH SPEED BACKSTOPPING Model CSK Skeet shooting enthusiasts rely on clay pigeon throwing machines using Stieber overrunning clutches to reduce costs and enjoy longer operating life. The Stieber model CSK clutch is used on clay pigeon throwing machines as a backstop to prevent oscillation of the throwing arm after each stroke. The CSK clutch allows free rotation in the throwing (or overrunning) direction and prevents any rotation in the opposite direction. Bore Range:.3 to 1.57 in. (8 to 40 mm) Torque Range: 2.6 to 284 lb.ft. (3,5 to 385 Nm) PUMP BACKSTOPPING SB Clutches are used on fluid pumping equipment to provide a backstopping function preventing any reverse rotation. In a simple electric motor/pump drive system, the SB clutch is mounted on the electric motor shaft with the output shaft of the SB clutch coupled to the pump s input shaft. The SB clutch with a torque arm attached to the outer race allows the pump to rotate only in the driving direction. Model SB BBore Range:.75 to 7.0 in. (19 to 177 mm) Torque Range: 875 to 22,300 lb.ft. (1190 to 30328 Nm) 7
Formsprag Clutch Facilities North America USA 23601 Hoover Road Warren, MI 48089 - USA 586-758-5000 Clutches and Holdbacks Customer Service 1-800-927-3262 Application Support 1-800-927-3262 Europe Germany` Hatschekstraße 36 69126 Heidelberg - Germany +49 (0) 6221-30470 Clutches and Holdbacks Asia Pacific Australia +61 2 9894 0133 China +86 21 5169-9255 Hong Kong +852 2615 9313 Singapore +65 6487 4464 Taiwan +886 2 2577 8156 Thailand +66 2322 5527 The Brands of Altra Industrial Motion Couplings Ameridrives www.ameridrives.com Bibby Turboflex www.bibbyturbofl ex.com Guardian Couplings www.guardiancouplings.com Huco www.huco.com Lamiflex Couplings www.lamifl excouplings.com Stromag www.stromag.com TB Wood s www.tbwoods.com Geared Cam Limit Switches Stromag www.stromag.com Electric Clutches & Brakes Inertia Dynamics www.idicb.com Matrix www.matrix-international.com Stromag www.stromag.com Warner Electric www.warnerelectric.com Linear Products Warner Linear www.warnerlinear.com Engineered Bearing Assemblies Kilian www.kilianbearings.com Heavy Duty Clutches & Brakes Industrial Clutch www.indclutch.com Twiflex www.twifl ex.com Stromag www.stromag.com Svendborg Brakes www.svendborg-brakes.com Wichita Clutch www.wichitaclutch.com Belted Drives TB Wood s www.tbwoods.com Gearing Bauer Gear Motor www.bauergears.com Boston Gear www.bostongear.com Delroyd Worm Gear www.delroyd.com Nuttall Gear www.nuttallgear.com Clutches Formsprag Clutch Marland Clutch www.marland.com Stieber www.stieberclutch.com Neither the accuracy nor completeness of the information contained in this publication is guaranteed by the company and may be subject to change in its sole discretion. The operating and performance characteristics of these products may vary depending on the application, installation, operating conditions and environmental factors. The company s terms and conditions of sale can be viewed at http://www.altramotion.com/terms-and-conditions/sales-terms-and-conditions. These terms and conditions apply to any person who may buy, acquire or use a product referred to herein, including any person who buys from a licensed distributor of these branded products. 2018 by Formsprag Clutch LLC. All rights reserved. All trademarks in this publication are the sole and exclusive property of Formsprag Clutch LLC or one of its affi liated companies.