HIGH SPEED COMPACT DISC (HCD-32) Operation & Maintenance Manual OPERATORS MANUAL & PART LIST

HIGH SPEED COMPACT DISC (HCD-32) Operation & Maintenance Manual OPERATORS MANUAL & PART LIST

Quick Start Guide Hydraulic Connections to Tractor Yellow Lifting/lowering main frame and packers Black Disc gangs Red Forward Unfold System and wing pressure Green Wing axle tires Unfold to Field Position Find a location that is as level as possible. Position the machine in line with the tractor; bring the tractor to a full stop. Remove the safety pins from the wing axle and secure them in the field position holder. From the cab of the tractor, rotate pivot wings 90. Activate forward unfold cylinders (red line) to bring the wings fully forward. Slowly extend the main frame cylinders (yellow line) to lower the machine into field position. Continue lowering the main frame and packers until the packers fully engage the ground and raise the rear of the unit (packer cylinders fully extended). Apply wing down pressure by extending forward unfold cylinders (red line). You should see the wings shift down and the center frame shift up slightly. Release tractor hydraulic remote to lock pressure and allow the accumulators in the circuit to take over while working. Lower the disc gang sections while driving the tractor forward to begin tillage operation (black line). Drive the machine at least 50 metres to check if all packers, discs and wheels are rotating. Adjust the cutting depth if necessary. NOTE: Check the level of A-frame hitch relative to the tractor. Adjust using hitch tongue to level Check the level of bridge beams relative to the hitch A-frame. Adjust packer height by changing packer cylinder shims or by rotating clevis on threaded cylinder rod. FAILURE TO LEVEL THE UNIT CAN RESULT IN UNIT TRACKING TO ONE SIDE DURING OPERATION. FUTHER INFORMATION ON LEVELLING CAN BE FOUND IN YOUR OPERA- TOR S MANUAL. Cutting Depth Adjustment The disc section cylinders contain flip-down spacers. The cutting depth can be controlled by flipping down the appropriate number of spacers onto the shaft of the cylinders. Refer to the chart as a guide to achieve the desired cutting depth. Shims Disc Depth 0 5-1/2 1 5" 2 4.5" 3 4" 4 3.5" 5 3" 6 2.5" 7 2" 8 1.5" 9 1" 1

Contents SECTION 1 PAGE INTRODUCTION MANUAL & EQUIPMENT DETAILS SPECIFICATIONS PRE-DELIVERY INSPECTION SERVICE & WARRANTY POLICY SAFETY RECOMMENDATIONS DECAL LOCATIONS MAINTENANCE OPERATING INSTRUCTIONS GRADE CHART TORQUE CHART SECTION 2 PAGE PARTS Table of Contents

SECTION 1 HCD-32

Thank you for making the decision to purchase a RITE WAY We are pleased to welcome you as an owner of a product from RITE WAY MFG. This machinery is the culmination of years of agricultural and engineering experience and has been designed to deliver you with many years of successful operation service. For the most efficient operation of your HCD-32 we have provided this owner s manual. In this manual we have included proper maintenance and functional procedures to offer maximum longevity for your new equipment. Before operating we urge a careful study of this manual to provide a thorough understanding of your new HCD-32. We also recommend that you take care of this manual so it will be available for future reference. Should your manual become lost or destroyed a new copy can be obtained from your Rite Way Manufacturing dealer. We will also be happy to answer any questions you might have concerning the use or care of this product. Rite Way Manufacturing Co. Ltd. P.O. Box 328 Imperial, Saskatchewan, Canada S0G 2J0 PH: 306-963-2180 Fax: 306-963-2660 Web Site: www.ritewaymfg.com Email: info@ritewaymfg.com Introduction 1

Manual Details Unit Model Number HCD-32 Manual Revision Number 2.0 Manual Revision Date July 3th, 2017 Manual Serial Number Range 17-32-031 to 18-32-050 The area below is provided for the owner / end-user to make notes regarding the equipment. Owner / Equipment Information Serial Number of Unit Date of Purchase Dealer Name Dealer Address Dealer Phone Number Salesman Name Salesman Phone Number Notes 2 Manual Information

Specifications General Information Adjustable Disc Cutting Depth from 1-1/2 To 4-5/8 Consistent 5 Disc Spacing Independent Disc Suspension Adjustable Hitch Height With Category 5 Perfect Hitch Aggressive 560/45R22.5 Tires Light Kit Slow Moving Sign Notched 20 Concave Discs (Options Available) Chevron Packer Rollers (Options Available) Heavy Duty Disc Bearings (Options Available) Chrome Plated Pins Main Frame & Wings Heavy Duty 10 x 4 x 0.375W Tube Heavy Duty 8 x 8 x 0.250W Tube Hydraulic System Standard unit requires - 8 Hydraulic Banks. Heavy duty hydraulic welded cylinders. Synchronized Disc Gang Lift Circuit High Mounted Cylinders Accumulator equipped circuits for maximum suspension and contouring Options Rubber Packer Rollers Rubber Packer Rollers With Scrapers Basket Packer Rollers Wavy 20 Concave Discs Smooth 20 Concave Discs Ultra Heavy Duty Disc Bearings Working Width Transport Length Transport Width Transport Height Weight Required Power Ideal Speed Technical Information 32ft (9.75m) 30-4 (9.25m) 13-8 (4.17m) 13-1 (3.99m) 32,000 lbs (14545 kg) 15hp / foot 10-12 mph (16-19 km/h) Specifications 3

Pre-delivery Inspection Check List General Remove wrapping and wash unit, removing all road debris. (Road salt, mud, snow, etc.) Inspect paint, decals and general appearance of unit. Verify that the owners manual is in the manual storage tube. Verify SLOW MOVING VEHICLE sign (SMV) is on unit (if applicable) Verify that jacks are with the unit and function properly. Check wheel bolts for proper torque. Check for proper tire pressure (PSI). Verify that the wheel hubs are lubricated. Verify that locking pins and / or ram locks are in place. Lubricate all components as per operators manual recommendation. Check that all bolts and fasteners are at the proper torque specifications. (NOTE: All cap screws that have lock nuts join moving pieces should not be tightened completely, they must allow movement. i.e. Spring pressure kits, rock shaft connector, draft arm, etc. Check sprocket alignment and chain tension. (If applicable) Check locking collars and set screws for proper tension. (If applicable) Verify operation of lights. (If applicable) Verify the unit moves IN and OUT of transport without any binding. Verify that tires are tracking properly when in transport mode. Hydraulics Insure that all hydraulic hoses and lines are routed properly and secured. Verify that all hydraulic fittings / hoses are secure and there are no oil leaks. Inspect all cylinders for leakage and the cylinder shaft for rust, pits, or scratches. Verify operation of all hydraulic functions - Cycle hydraulic cylinders to remove air from the system. Delivery Verify that The customer is aware of warning decals and proper jack placement for transport.. Verify that The customer is aware of proper operation and transportation of the unit. Verify that The customer has received an operators manual. Explain all maintenance and service intervals to the customer (From operators manual). Advise the customer of grease zerk locations and maintenance schedules. Level the unit per operators manual and instruct the customer on the proper procedures. Pre-delivery Inspection Completed By (Sign Below) Pre-delivery Inspection Confirmed By (Sign Below) 4 Pre-delivery Inspection Check List

Service & Warranty Policy Rite Way Manufacturing Co. Ltd. (hereafter referred to as Rite Way) warrants each new machine to be free from defects in materials and workmanship for a period of one (1) year from date of purchase under normal agricultural use and service. In addition, Rite Way will supply at no charge, (F.O.B Rite Way Factory) any part that has failed within the 2nd year. Rite Way s obligation under this warranty is limited to the repair or replacement of any defective parts of the equipment at its own discretion. Any alterations, modifications or additions done to a finished product will void this warranty unless prior written permission from Rite Way is obtained. Items that are not manufactured by Rite Way are covered by the warranty of the supplier of these items. We will therefore extend, without assuming any responsibility, any warranty given to us by our suppliers. This warranty shall-not apply to any machine, that in the company s judgment has be subjected to misuse, negligence or accident. In no event shall the owner be entitled to recover costs for incidental, special or consequential damages such as, but not limited to; Loss of crop, loss of profit or revenue, other commercial losses, inconvenience or rental costs. This warranty shall not apply unless Rite Way or its designated dealer is promptly notified of claimed defects and the allegedly defective part is held for inspection. Repair parts purchased for machines Out of Warranty, are warranted to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of delivery to the customer. The warranty shall only become valid when delivery notification for warranty is received by Rite Way within 20 days of the completion of sale. OWNER S / USERS OBLIGATION: It is the responsibility of the user to read the Operators Manual and understand the safe and correct operating procedures as it pertains to the operation of the product, and to lubricate and maintain the product according to the maintenance schedule in the Manual. The user is responsible for inspecting the machine, and for having parts repaired or replaced when continued use of the product could cause damage or excessive wear to any other parts. It is the user s responsibility to deliver their machine to a Rite Way dealer for service or replacement of defective parts which are covered by the standard warranty. Rite Way will not by held responsible for charges such as transportation, fuel, lodging when a dealer / dealer representative travels to a customer location for warranty or inspection. Service & Warranty Policy 5

Service & Warranty Claim Procedure 1. All claims must be handled through a dealer / distributor. All claims must be submitted on a properly completed claim form within 30 days of the date of repair. 2. A warranty registration claim form must be on file at Rite Way Mfg. to validate a warranty claim. 3. Defective parts are to be held at the dealer / distributor s place of business until the warranty claim form has been processed. Rite Way will advise when parts can be released. 4. Parts that require inspection by Rite Way personnel must be accompanied by a Return Goods Form number, and must be sent by pre-paid freight. Rite Way will refund pre-paid freight charges on any items determined to be defective. 5. Rite Way will not assume responsibility for repairs or expenses incurred without authorization. Warranty labour in excess of $150.00 must be authorized before such work is performed and photographs before and after repairs are required. 6. Warranty labour is to be claimed on the warranty claim form, only if the warranty labour was performed by the dealer. Travel time is not covered by warranty and should not be included. Rite Way reserves the right to adjust or allocate labour times and values based on its experience. 7. It is the responsibility of the dealer to ensure that the warranty registration forms are properly completed and returned to Rite Way Mfg., Imperial, SK. 6 Service & Warranty Policy

Safety Recommendations 1. Read manual thoroughly before operating machine. 2. Study all warning decals on implement. 3. Most accidents occur because of neglect or carelessness. 4. Do not allow riders on the tractor or implement during operation. 5. Do not allow children on or near the machine. 6. Connect the implement hitch to the tractor before operating the hydraulic system. NOTE: Be aware of any hydraulic leaks. 7. Always throttle the tractor down and use caution when connecting the implement to the tractor hitch. NOTE: Never stand between the tractor and implement. 8. Lower the hitch jack onto firm ground and chock the tires when un-hooking implement from tractor. NOTE: Ensure the unit is on level ground prior to un-hooking tractor. 9. Exercise extra caution when working on hillsides or near ditches. 10. Ensure that the tractor draw-bar is pinned during transport. 11. Maximum speed while transporting the HCD-32 is 38 mph (60 km/h). 12. Ensure that the HCD-32 frame is lowered to the ground before doing any work on machine. NOTE: If it is necessary to work on machine with the drawbar raised, ensure that cylinders are locked in position using the lock pin. 13. Do not work on this machine when hydraulic system is under pressure. 14. Observe all laws and regulations when transporting unit on public roads. 15. Do not transport this machine on public roads unless all safety & maintenance checks have been completed. This machine will provide years of trouble-free & safe operation IF all maintenance and safety instructions are followed. Safety Recommendations 7

HCD-32 Decal Locations 1 Front Facing Portions of Machine, Several Locations 2 Rear Facing Portions of Machine, Several Locations 3 Beside Each Grease Location (See Pages 12-13) 4 5 6 7 8 9 11 10 12 10 12 8 Decal Locations 8

Decal Locations Item # Part # Description 1 060-0009 Amber Reflector (3 x 2) 2 060-0022 Red Reflector (3 x 2) 3 060-0046 Grease Every 8 Hours 4 060-0011 Caution - Escaping Fluid Hazard... 5 060-0015 Important - Block Wheels... 6 060-0028 Warning - Lower or Block Elevated Components 7 060-0034 Riteway Serial Number Plate 8 060-0038 Attention - Insure That All Cylinders Are Retracted... 9 060-0067 Warning - Check And Tighten Hub... 10 060-0072 Riteway Mfg. (Large Decal, 31 x 5 - White) 11 060-0106 Important - Hydraulic Hose Application 12 060-0109 ONE TILL (LARGE) ONE TILL 18-32-036 UNIT SERIES UNIT SIZE MODEL YEAR UNIT NUMBER 9 Decal Locations 9

Maintenance General Repack the wheel hubs after the first 500 kilometres of travel ; then yearly thereafter. Visually inspect the wheel bolts for tightness each day. Torque to 110 lbs ft (149 Nm) after the first few hours of operation and frequently thereafter. (Manufacturer s torque recommendations: 90 to 131 lbs ft (122 Nm to 178 Nm)). After first eight hours of operation in the field check the roller drum bearing locking collar then check it annually and tighten as necessary. Every 8 Hours (Daily) Grease all pins. (See decals locations) Every 100 Hours (Monthly) Visually inspect hydraulic hoses & fittings for leaks or damage. Annually Inspect wheel bearings / hubs for tightness and grease. Check wheel bolts for tightness and re-torque. Check tire pressure. Recommended pressure: 58 psi. Visually inspect unit for loose, worn or damaged components. 10 Maintenance

Maintenance Storage Coat any exposed cylinder shafts with thick oil or grease. Ensure that parking jacks are situated on firm ground. Failure to do so may cause the hitch to rise sharply as the jack pads sink into the ground. Lock all applicable safety pins into place. NOTE: All fasteners with locknuts that are used to join moving pieces should not be tightened completely to allow for movement. Maintenance 11

HCD-32 Maintenance Grease Locations 12 Maintenance

HCD-32 Maintenance Grease Locations (Cont.) Maintenance 13

Operating Instructions Tire Pressure: Transport 58psi, Field 35 psi In transport position, the maximum turning angle is 40. Turning too tight will cause severe damage to the machine. Always choose a level area when folding the unit in or out of transport mode. Lubricate all pins, axles and bearings regularly to prevent premature failure. Clean hydraulic hose ends prior to coupling with tractor hydraulic system. The HCD requires four sets of hydraulic outlets to operate the machine. Yellow Lifting/lowering main frame and packers Black Disc gangs Green Wing axle tires Red Wing fold and wing pressure General Information Hitch A-Frame Left Wing Center Bar Right Wing 14 Operating Instructions

Operating Instructions Tractor Hook-Up Tractor Hook-up Move the tractor into position where the pin can be dropped in place through the draw bar hitch. If there is too much negative hitch weight, you can lower the hitch by connecting the yellow main frame/packer circuit and adjusting the hitch. Retract the parking jack and move to inboard frame storage position before moving the machine. NOTE: Use a clevis-type tractor hitch with a retained type of hitch pin. NOTE: Ensure that the parking jack handle is secured by chain prior to moving the machine. Failure to do so will destroy the jack handle. Hook up the four hydraulic circuits to your tractor remote. Recommended Hydraulic Connections: Remote 1 Black Disc gangs Remote 2 Yellow Lifting/lowering main frame and packers Remote 3 Red Wing fold and wing pressure Remote 4 Green Wing axle tires Tractor Disconnecting Field Position Ensure that the packers and disc gangs are fully lowered. Chock the A-frame tires, front and back, before disconnecting from the tractor. Lower the parking jack into position until upward pressure is applied and the hitch is raised off of the tractor clevis. Tractor Disconnecting Transport Position Ensure that the packers and disc gangs are fully raised. Chock the A-frame tires, front and back, before disconnecting from the tractor. Lower the parking jack into position until upward pressure is applied and the hitch is raised off of the tractor clevis. NOTE: Ensure the jack is placed on firm ground prior to unhooking. NOTE: The hitch may rise suddenly. If it does, re-connect the yellow hydraulic circuit and adjust the height downward. Operating Instructions 15

Operating Instructions Transport to Field Position Hook up tractor according to prior instructions. Ensure that the safety pins are in transport position. When entering the field from transport mode, find a level location. Position the machine in-line with the tractor and bring the tractor to a full stop. Remove the wheel pivot safety pins from transport position to field position and secure (fig. 1). NOTE: Failing to do so may cause severe damage to the machine. Safety Pin (transport position) Safety Pin (field position) Figure 1 16 Operating Instructions

Operating Instructions Transport to Field Position (Cont.) Rotate wing axle tires 90 degrees (green line) (fig. 2). Activate forward unfold cylinders (red line) to open wings until they are in line with the centre section (fig. 3). Slowly extend the main frame cylinders (yellow line) so that the whole machine goes over center the hitch goes up slightly (fig. 4). NOTE: There will be significant negative hitch tongue weight when the unit is lowered into field position. Ensure that the unit is securely attached to the clevis hitch of the tractor to prevent upending. Figure 2 Figure 3 Figure 4 Operating Instructions 17

Operating Instructions Transport to Field Position (Cont.) Proceed with lowering the frame until the packers touch the ground. Hold the remote connected to the yellow circuit pressure and ensure packer cylinders extend fully. (fig. 5) (fig 6). Extend wing fold cylinders (red line) until the centre section is level with the wings (approximately 1-2 inches of chrome rod showing on all wing fold cylinders). Drive forward at 10-12MPH. Lower disc sections to begin working (black hydraulic line) (fig. 7). Figure 5 Figure 6 Figure 7 18 Operating Instructions

Operating Instructions Leveling and Depth Adjustment A-frame to Tractor Move the unit to field position on level ground Measure from bottom of tubing on the A-frame to the ground near the implement s tire. Measure from bottom of tubing and the A-frame to the ground near the tractor. Adjust the hitch-clevis accordingly so the A-frame is level (± 1 difference allowed). Main Frame to Ground With the A-frame leveled and the unit on level ground, check the level of the centre bridge. The bridge should be level within ½ from front to rear. If the bridge is not level, lower the discs to the ground and raise packers slightly to take weight off the packer cylinders. Un-pin packer cylinder clevis and thread on/off as necessary and replace clevis pins. Clockwise turn=shorter cylinder pin-pin=lower rear of frame. Re-apply pressure to A-frame/packers and check for level. Repeat as necessary until unit is level from rear to rear. NOTE: An out of level machine will cut deeper on the front or rear row of disks and therefore will skew to one side while working with disks down. Cutting Depth Adjustment The disc gang cylinders are equipped with a custom clevis containing flip down shims. A desired number of spacers can be rotated onto the cylinder rod by removing the quick adjust pin. This will control your cutting depth as shown in the chart (depending on level of disc wear): NOTE: ¼ thick depth shim flipped down = ½ shallower disc depth Shims Disc Depth 0 5-1/2 1 5" 2 4.5" 3 4" 4 3.5" 5 3" 6 2.5" 7 2" 8 1.5" 9 1" Operating Instructions 19

Operating Instructions Fully raise disc sections off the ground (black hydraulic line) (fig. 8). Bring the machine to a full stop on a level part of the field. Raise the main sections of the machine and the packers (yellow hydraulic line). Make sure the main lift cylinders are fully retracted. (fig. 9) (fig. 10). Field to Transport Position NOTE: Be prepared for over-centre movement of the main frame. Figure 8 Figure 9 Figure 10 20 Operating Instructions

Operating Instructions Field to Transport Position (Cont.) Activate forward unfold cylinders to bring the wings into transport position. If the wings do not go all the way back, adjust the pivot wheels while folding the wings. Adjust wing fold cylinders so both wings are straight back. (fig. 11)(fig. 12) Rotate wing axle wheels 90 until the wheels point forward (green line) (fig. 13). Move the safety pins to transport position from field position and secure it with a cotter pin (fig. 1). NOTE: If you cannot fold up the wings, fully unfold, lower the main frame, and drive to a more level location before attempting the fold. Figure 11 Figure 12 Figure 13 Operating Instructions 21

Grade Chart Specification Material Size Range (inches) Min. Proof Strength (psi) Min. Tensile Strength (psi) Min. Yield Strength (psi) Grade Identification Marking Grade 2 Low or Medium Carbon Steel 1/4 to 3/4 7/8 to 1-1/2 55,000 33,000 74,000 60,000 57,000 36,000 Grade 5 Medium Carbon Steel: Quenched and Tempered 1/4 to 1 1-1/8 to 1-1/2 85,000 74,000 120,000 105,000 92,000 81,000 Grade 8 Medium Carbon Alloy Steel: Quenched and Tempered 1/4 to 1-1/2 120,000 150,000 130,000 22 Grade Chart

Torque Chart Grade 2 Grade 5 Grade 8 Nominal Thread Size Clamping Load Tightening Torque Clamping Load Tightening Torque Clamping Load Tightening Torque Coarse Thread 1/4-20 1,300 lbs 65 in-lbs 2,000 lbs 100 in-lbs 2,850 lbs 143 in-lbs 5/16-18 2,150 lbs 134 in-lbs 3,350 lbs 210 in-lbs 4,700 lbs 305 in-lbs 3/8-16 3,200 lbs 20 ft-lbs 4,950 lbs 31 ft-lbs 6,950 lbs 44 ft-lbs 7/16-14 4,400 lbs 30 ft-lbs 6,800 lbs 50 ft-lbs 9,600 lbs 70 ft-lbs 1/2-13 5,850 lbs 49 ft-lbs 9,050 lbs 75 ft-lbs 12,800 lbs 107 ft-lbs 9/16-12 7,500 lbs 70 ft-lbs 11,600 lbs 109 ft-lbs 16,400 lbs 154 ft-lbs 5/8-11 9,300 lbs 97 ft-lbs 14,500 lbs 151 ft-lbs 20,300 lbs 211 ft-lbs 3/4-10 13,800 lbs 173 ft-lbs 21,300 lbs 266 ft-lbs 30,100 lbs 376 ft-lbs 7/8-9 11,425 lbs 166 ft-lbs 29,435 lbs 430 ft-lbs 41,550 lbs 606 ft-lbs 1-8 15,000 lbs 250 ft-lbs 38,600 lbs 640 ft-lbs 54,540 lbs 900 ft-lbs Fine Thread 1/4-28 1,500 lbs 75 in-lbs 2,300 lbs 115 in-lbs 3,250 lbs 163 in-lbs 5/16-24 2,400 lbs 150 in-lbs 3,700 lbs 230 in-lbs 5,200 lbs 325 in-lbs 3/8-24 3,600 lbs 23 ft-lbs 5,600 lbs 35 ft-lbs 7,900 lbs 50 ft-lbs 7/16-20 4,900 lbs 36 ft-lbs 7,550 lbs 55 ft-lbs 10,700 lbs 78 ft-lbs 1/2-20 6,600 lbs 55 ft-lbs 10,200 lbs 85 ft-lbs 14,400 lbs 120 ft-lbs 9/16-18 8,400 lbs 79 ft-lbs 13,000 lbs 112 ft-lbs 18,300 lbs 172 ft-lbs 5/8-18 10,600 lbs 110 ft-lbs 16,300 lbs 170 ft-lbs 23,000 lbs 240 ft-lbs 3/4-16 15,400 lbs 193 ft-lbs 23,800 lbs 298 ft-lbs 33,600 lbs 420 ft-lbs 7/8-14 12,610 lbs 184 ft-lbs 32,480 lbs 473 ft-lbs 45,855 lbs 668 ft-lbs Torque Chart 23

SECTION 2 ITEMS HIGLIGHTED RED HAVE INDIVIDUAL BREAK-DOWNS

A-Frame, Hitch 04 A-Frame, Hitch

A-Frame, Hitch Item # Part # Description 3 105-0556 A FRAME WELDMENT (X-STYLE) 5 413-0008 HYDRAULIC CLAMP, 2 LINE, BLACK PLASTIC 6 526-2048 BOLT, 3/8-16 UNC - 3, GR.5, YELLOW ZINC PLATED, W THREAD LOCK 7 550-5206 WASHER, FLAT, 3/8 - Regular, GR.5, YELLOW ZINC PLATED 8 407-0003 24" SHEPHERD HOOK HOSE STANDOFF 9 409-9050 SAFETY CHAIN 20,000LB, CLEVIS MOUNT, NEW STYLE 10 420-0145 20" SIDE WINDER 3000 lb PARKING JACK 11 423-0021 Crossover Hitch - CAT. 4-5 12 426-0001 MANUAL STORAGE TUBE 13 426-0002 MANUAL STORAGE TUBE CAP 14 520-0809 CLAMP, 6.00" DIAMETER 15 526-5206 NUT, HEX, INCH, GRADE 5, YELLOW ZINC PLATED 16 526-6103 NUT, STOVER LOCK, 3/8-16 UNC, GR.5, YELLOW ZINC PLATED 19 526-6109 NUT, STOVER LOCK, 1-8 UNC, GR.5, YELLOW ZINC PLATED 20 526-7008 NUT, NYLOCK, HEX, INCH, GRADE 5, YELLOW ZINC PLATED 21 530-0611 BOLT, 3/8-16 UNC - 1, GR.8, YELLOW ZINC PLATED 22 530-0740 BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED 24 530-1636 BOLT, 1-8 UNC - 3.5, GR.8, YELLOW ZINC PLATED 25 530-1664 BOLT, 1-8 UNC - 8, GR.8, YELLOW ZINC PLATED 26 550-5206 WASHER, FLAT, 3/8 - Regular,GR.5, YELLOW ZINC PLATED 27 550-5306 WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED 28 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 30 550-5316 WASHER, FLAT, 1" - SAE, GR.5, YELLOW ZINC PLATED 31 551-5006 WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED 39 710-5010 ACCUMULATOR, 1.4L, #8 ORB, CHARGED TO 1800PSI 40 835-1009r2 CHAIN AND TIP HOLDER 14-1/4 X 8 41 839-0863 MOUNT, HYDRAULIC BULKHEAD - #6 & #8 JIC 42 839-1442 ACCUMULATOR MOUNT, 3 POSITION 43 850-3103 BOLT, 3/8-16 UNC - 0.75, GR.8, YELLOW ZINC PLATED 44 850-3106 BOLT, 3/8-16 UNC - 1.25, GR.8, YELLOW ZINC PLATED 46 526-0610 BOLT, HEX, INCH, GRADE 5, YELLOW ZINC PLATED 47 526-6103 NUT, STOVER LOCK, 3/8-16 UNC, GR.5, YELLOW ZINC PLATED 52 550-5206 WASHER, FLAT, 3/8" - USS, GR.5, YELLOW ZINC PLATED A-Frame, Hitch 05

A-Frame, Center Axle 06 A-Frame, Center Axle

A-Frame, Center Axle Item # Part # Description 1 105-0934 CENTER BRIDGE WELDMENT 2 105-0552 A-FRAME AXLE 4 105-0587 CTD 812 AXLE STUB 17 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 18 526-6107 NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED 23 530-1018 BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED 29 550-5312 WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED 32 554-1030 WASHER, FLAT, 5/8 - narrow, GR.5, YELLOW ZINC PLATED 33 680-1001 HUB ASSEMBLY, INCL BEARINGS, SEALS, CAP 34 680-1001 WHEEL HUB, DUST CAP 35 680-1002 SPINDLE, 1010 SERIES, 3" OD X 17.38" LNG, 12000 LB 36 680-1003 3/4 WHEEL STUD, NF 37 680-1003 3/4" FLANGE NUT 38 690-1003 TIRE / RIM ASSY, 560/45R22.5 45 850-3367 BOLT, 3/4-10 UNC - 5, GR.8, YELLOW ZINC PLATED 48 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 49 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 50 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 51 530-1026 BOLT, 5/8-11 UNC - 4.5, GR.8, YELLOW ZINC PLATED 53 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 54 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 55 670-0012 CYLINDER, HYD - 6.0" x 32", 3.0" SHAFT, WELDED 56 827-0134 PIN, 1.75 X 4.25 - MAIN FRAME LIFT CYLINDER 57 827-0204 PIN, HITCH TO CENTER FRAME 58 827-0206 PIN, MAIN LIFT CYLINDER TO CENTER FRAME A-Frame, Center Axle 07

Center Frame 08 Center Frame

Center Frame Item # Part # Description 1 105-0086 PIN WELDMENT, WING HOOK, CYLINDER, YZP 2 105-0928 GANG LINK, WITH LUG 3 105-0929 GANG LINK, WITHOUT LUG 4 105-0935 WING WELDMENT, LEFT 5 160-0493 A-FRAME ASSEMBLY 6 160-0579 HCD DISC DEPTH SHIM ASSEMBLY 7 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 8 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 9 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 10 530-0754 BOLT, 1/2-13 UNC - 4, GR.8, YELLOW ZINC PLATED 11 530-1026 BOLT, 5/8-11 UNC - 4.5, GR.8, YELLOW ZINC PLATED 12 550-5306 WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED 13 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 14 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 15 551-5006 WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED 16 670-0012 CYLINDER, HYD - 6.0" X 32", WELDED 17 670-0044 CYLINDER, HYD - REPHASING 4.00" X 10", WELDED 18 827-0204 PIN, HITCH TO CENTER FRAME 19 827-0205 PIN, CENTER FRAME TO WING 20 827-0206 PIN, MAIN LIFT CYLINDER TO CENTER FRAME 21 827-0207 PIN, PARALLEL LINK TO BRIDGE 22 827-0208 PIN, PARALLEL LINK TO GANG 23 827-0209 PIN, PACKER 24 839-1465 MOUNT, HYDRAULIC BULKHEAD 6 X #6 JIC - OFFSET 25 850-3103 BOLT, 3/8-16 UNC - 0.75, GR.8, YELLOW ZINC PLATED Center Frame 09

Wing (Left Pictured) 10 Wing (Left Pictured)

Wing (Left Pictured) Item # Part # Description 4 105-0929 GANG LINK, WITHOUT LUG 5 105-0934 CENTER BRIDGE WELDMENT 6* 105-0935 WING WELDMENT, LEFT 6* 105-0936 WING WELDMENT, RIGHT 8 105-0948 WING FOLD ROCKER WELDMENT 9 105-0954 PIN, WING FOLD ROCKER 10 105-0937 COIL PACKER MOUNT WELDMENT, MEDIUM 18 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 21 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 22 530-0754 BOLT, 1/2-13 UNC - 4, GR.8, YELLOW ZINC PLATED 26 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 28 670-0017 CYLINDER, HYD - 3.5" X 8", WELDED 35 827-0205 PIN, CENTER FRAME TO WING 36 827-0207 PIN, PARALLEL LINK TO BRIDGE 38 827-0209 PIN, PACKER Disc Gang, Center 11

Wing - Cont. (Left Pictured) 12 Wing (Left Pictured)

Wing - Cont. (Left Pictured) Item # Part # Description 1 105-0086 PIN WELDMENT, WING HOOK, CYLINDER, YZP 2 105-0730 WING AXLE, SAFETY PIN WELDMENT 3 105-0928 GANG LINK, WITH LUG 7* 105-0939 LEFT WING AXLE WELDMENT 7* 105-0940 RIGHT WING AXLE WELDMENT 11 160-0579 HCD DISC DEPTH SHIM ASSEMBLY 12 417-0018A AMBER WARNING LIGHT 13 417-0019A RED WARNING LIGHT 14 424-0001 SLOW MOVING SIGN 15 424-0002 SLOW MOVING SIGN SPADE 16 525-6116 NUT, JAM, 1-8 UNC, GR.5, YELLOW ZINC PLATED 17 526-0406 BOLT, 1/4-20 UNC - 0.75, GR.5, YELLOW ZINC PLATED 19 526-6107 NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED 20 526-6204 NUT, STD, 1/4-20 UNC, GR.5, YELLOW ZINC PLATED 23 530-1636 BOLT, 1-8 UNC - 3.5, GR.8, YELLOW ZINC PLATED 24 550-5204 WASHER, FLAT, 1/4" - SAE, GR.5, YELLOW ZINC PLATED 25 550-5306 WASHER, FLAT, 3/8" - SAE, GR.5, YELLOW ZINC PLATED 27 551-5006 WASHER, SPRING, 3/8, GR.5, YELLOW ZINC PLATED 29 670-0018 CYLINDER, HYD - 4.0" X 10", WELDED 30 670-0042 CYLINDER, HYD - REPHASING 3.5" X 10", WELDED 31 680-1003 HUB & SPINDLE ASSY 32 680-1003 3/4 WHEEL STUD, NF 33 680-1003 3/4" FLANGE NUT 34 690-1003 TIRE / RIM ASSY, 560/45R22.5 37 827-0208 PIN, PARALLEL LINK TO GANG 39 839-0938 WING BRIDGE LIGHT MOUNT 40 850-3103 BOLT, 3/8-16 UNC - 0.75, GR.8, YELLOW ZINC PLATED 41 850-3367 BOLT, 3/4-10 UNC - 5, GR.8, YELLOW ZINC PLATED 42 550-5312 WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED Disc Gang, Center 13

Disc Gang, Center 14 Disc Gang, Center

Disc Gang, Center Item # Part # Description 1 105-0934 CENTER BRIDGE WELDMENT 2 105-0970 GANG CONNECT LINK BAR WELDMENT 3 105-0971 GANG MOUNT BAR WELDMENT, CENTER, REAR 4 105-0972 GANG MOUNT BAR WELDMENT, CENTER, FRONT 5 160-0537 DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY 6 160-0538 DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY 7 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 8 530-1022 BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED 9 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 10 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 11 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 12 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 13 827-0208 PIN, PARALLEL LINK TO GANG Disc Gang, Center 15

Disc Gang, Right 16 Disc Gang, Right

Disc Gang, Right Item # Part # Description 1 105-0936 WING WELDMENT, RIGHT 2 105-0970 GANG CONNECT LINK BAR WELDMENT 3 105-0973 GANG MOUNT BAR WELDMENT, RIGHT, REAR 4 105-0974 GANG MOUNT BAR WELDMENT, RIGHT, FRONT 5 105-0977 GANG BAR EXTENSION WELDMENT 6 105-0978 GANG BAR FINISHING DISC WELDMENT 7 160-0537 DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY 8 160-0538 DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY 9 160-0546 DISC MOUNT ARM - RIGHT END 10 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 11 530-1018 BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED 12 530-1020 BOLT, 5/8-11 UNC - 2.75, GR.8, YELLOW ZINC PLATED 13 530-1022 BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED 14 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 15 839-1473 GANG SECTION FINISHING PLATE, EXTENDED 16 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 17 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 18 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 19 827-0208 PIN, PARALLEL LINK TO GANG Disc Gang, Right 17

Disc Gang, Left 18 Disc Gang, Left

Disc Gang, Left Item # Part # Description 1 105-0935 WING WELDMENT, LEFT 2 105-0970 GANG CONNECT LINK BAR WELDMENT 3 105-0975 GANG MOUNT BAR WELDMENT, LEFT, REAR 4 105-0976 GANG MOUNT BAR WELDMENT, LEFT, FRONT 5 105-0977 GANG BAR EXTENSION WELDMENT 6 105-0978 GANG BAR FINISHING DISC WELDMENT 7 160-0537 DISC, SINGLE SECTION RIGHT CUT ARM ASSEMBLY 8 160-0538 DISC, SINGLE SECTION LEFT CUT ARM ASSEMBLY 9 160-0547 DISC MOUNT ARM - LEFT END 10 526-6106 NUT, STOVER LOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 11 530-1018 BOLT, 5/8-11 UNC - 2.5, GR.8, YELLOW ZINC PLATED 12 530-1022 BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED 13 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 14 839-1467 GANG SECTION FINISHING PLATE 15 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 16 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 17 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 18 827-0208 PIN, PARALLEL LINK TO GANG Disc Gang, Left 19

Packer Sections, Center 20 Packer Sections, Center

Packer Sections, Center Item # Part # Description 1 105-1098 PIN WELDMENT, PACKER CYLINDER TO BRIDGE 2 105-0934 CENTER BRIDGE WELDMENT 3 105-0945 COIL PACKER MOUNT WELDMENT, CENTER 2 PIECE - LEFT 4 105-0946 COIL PACKER MOUNT WELDMENT, CENTER 2 PIECE - RIGHT 5 105-1054 SCRAPER MOUNT SIDE PLATE LEFT 6 105-1056 SCRAPER MOUNT SIDE PLATE RIGHT 7 105-1060 SCRAPER BAR SMALL 8 105-1061 SMALL RUBBER PACKER ROLLER, 16", 0.25"W 9 530-0740 BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED 10 530-0772 BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED 11 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 12 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 13 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 14 670-1011 RUBBER PACKER 15 827-0235 RUBBER PACKER ROLLER, SMALL, SHAFT 16 839-1714 RUBBER PACKER RETAINING RING 17 292-4018 2-7/16" ID LOCK COLLAR 19 292-4022 2-7/16"Ø FLANGE BEARING C/W ECENTRIC COLLAR 20 525-6108 NUT, JAM, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 21 530-0744 BOLT, 1/2-13 UNC - 2, GR.8, YELLOW ZINC PLATED 22 530-0749 BOLT, 1/2-13 UNC - 3.25, GR.8, YELLOW ZINC PLATED 23 530-0745 BOLT, 1/2-13 UNC - 2.25, GR.8, YELLOW ZINC PLATED 24 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 25 526-6208 NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 26 526-7010 NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 27 530-1022 BOLT, 5/8-11 UNC - 3, GR.8, YELLOW ZINC PLATED 28 530-1025 BOLT, 5/8-11 UNC - 4, GR.8, YELLOW ZINC PLATED 29* 540-1014 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 29* 540-1018 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK 30 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 31 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 32 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 33 839-0977 COIL PACKER, BEARING MOUNT PLATE 34 839-1225 PACKER MOUNT BOLT PLATE SPACER 35 839-1723 RUBBER PACKER SCRAPER BLADE SMALL 36 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 37 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 38 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 39 670-0002 CYLINDER, HYD - 2.5" X 6", WELDED 40 827-0209 PIN, PACKER Packer Sections, Center 21

Packer Sections, Wing, Outer 22 Packer Sections, Wing, Outer

Packer Sections, Wing, Outer Item # Part # Description 1 105-1098 PIN WELDMENT, PACKER CYLINDER TO BRIDGE 2 105-0936 WING WELDMENT, RIGHT 3 105-0938 COIL PACKER MOUNT WELDMENT, LARGE 4 105-1054 SCRAPER MOUNT SIDE PLATE LEFT 5 105-1055 SCRAPER BAR LARGE 6 105-1056 SCRAPER MOUNT SIDE PLATE RIGHT 7 105-1057 LARGE RUBBER PACKER ROLLER, 16", 0.25"W 8 530-0740 BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED 9 530-0772 BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED 10 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 11 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 12 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 13 670-1011 RUBBER PACKER 409mmID x 586mmOD 14 827-0237 RUBBER PACKER ROLLER, LARGE, SHAFT 15 839-1714 RUBBER PACKER RETAINING RING 16 292-4018 2-7/16" LOCK COLLAR, PLTD. 17 292-4022 2-7/16"Ø FLANGE BEARING c/w ECENTRIC COLLAR 18 530-0749 BOLT, 1/2-13 UNC - 3.25, GR.8, YELLOW ZINC PLATED 19 530-0745 BOLT, 1/2-13 UNC - 2.25, GR.8, YELLOW ZINC PLATED 20 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 21 526-6208 NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 22 526-7010 NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 23* 540-1014 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 23* 540-1018 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK 24 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 25 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 26 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 27 839-0977 COIL PACKER, BEARING MOUNT PLATE 28 839-1721 RUBBER PACKER SCRAPER BLADE LARGE 29 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 30 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 31 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 32 670-0002 CYLINDER, HYD - 2.5" X 6", WELDED 33 827-0209 PIN, PACKER Packer Sections, Wing, Outer 23

Packer Sections, Wing, Inner 24 Packer Sections, Wing, Inner

Packer Sections, Wing, Inner Item # Part # Description 1 105-1098 PIN WELDMENT, PACKER CYLINDER TO BRIDGE 2 105-0936 WING WELDMENT, RIGHT 3 105-0937 COIL PACKER MOUNT WELDMENT, MEDIUM 4 105-1054 SCRAPER MOUNT SIDE PLATE LEFT 5 105-1056 SCRAPER MOUNT SIDE PLATE RIGHT 6 105-1058 SCRAPER BAR MEDIUM 7 105-1059 MEDIUM RUBBER PACKER ROLLER, 16", 0.25"W 8 530-0740 BOLT, 1/2-13 UNC - 1.5, GR.8, YELLOW ZINC PLATED 9 530-0772 BOLT, 1/2-13 UNC - 4.5, GR.8, YELLOW ZINC PLATED 10 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 11 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 12 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 13 670-1011 RUBBER PACKER 409mmID x 586mmOD 14 827-0236 RUBBER PACKER ROLLER, MEDIUM, SHAFT 15 839-1714 RUBBER PACKER RETAINING RING 16 292-4018 2-7/16" LOCK COLLAR, PLTD. 17 292-4022 2-7/16"Ø FLANGE BEARING c/w ECENTRIC COLLAR 18 530-0749 BOLT, 1/2-13 UNC - 3.25, GR.8, YELLOW ZINC PLATED 19 530-0745 BOLT, 1/2-13 UNC - 2.25, GR.8, YELLOW ZINC PLATED 20 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 21 526-6208 NUT, STD, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 22 526-7010 NUT, NYLOCK, 5/8-11 UNC, GR.5, YELLOW ZINC PLATED 23* 540-1014 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 2.5, GR.5, BLACK 23* 540-1018 COUNTERSUNK ALLAN DRIVE BOLT, 5/8-11 UNC - 3, GR.5, BLACK 24 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 25 550-5310 WASHER, FLAT, 5/8" - SAE, GR.5, YELLOW ZINC PLATED 26 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 27 839-0977 COIL PACKER, BEARING MOUNT PLATE 28 839-1722 RUBBER PACKER SCRAPER BLADE MEDIUM 29 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 30 530-0750 BOLT, 1/2-13 UNC - 3.5, GR.8, YELLOW ZINC PLATED 31 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 32 670-0002 CYLINDER, HYD - 2.5" X 6", WELDED 33 827-0209 PIN, PACKER Packer Sections, Wing, Inner 25

Disc Gang, Shank 26 Disc Gang, Center

Disc Gang, Shank Item # Part # Description 1* 105-0950 SHANK WELDMENT, ONE PIECE, LEFT CUT 1* 105-0949 SHANK WELDMENT, ONE PIECE, RIGHT CUT 2 526-6107 NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED 3 530-1266 BOLT, 3/4-10 UNC - 2.5, GR.8, YELLOW ZINC PLATED 4 533-6514 JAM NUT 7/8" -14 UNF 5 534-7914 FLANGE NUT 7/8" - 14 UNF 6 538-0815 BOLT, 1/2-20 UNF - 1, GR.8, YELLOW ZINC PLATED 7 550-5312 WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED 8 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 9 670-1001 ISOLATOR, RUBBER, TORSION 10 680-1007 DISC HUB ASSEMBLY AG-1418, 6 HOLES X 100MM 11* 680-5004 DISC, 20" OD, 6 HOLE PATTERN,NOTCHED 11* 680-5005 DISC, 20" OD, 6 HOLE PATTERN,SERRATED 11* 680-5006 DISC, 20" OD, 6 HOLE PATTERN, SMOOTH 12 839-1448 SHANK, ONE PIECE, UPPER CLAMSHELL Disc Gang, Center 27

Disc Gang, Finishing Shank 28 Disc Gang, Finishing Shank

Disc Gang, Finishing Shank Item # Part # Description 1 105-0934 CENTER BRIDGE WELDMENT 1* 105-0959 SHANK WELDMENT, FINISHING, RIGHT CUT 1* 105-0960 SHANK WELDMENT, FINISHING, LEFT CUT 2 526-6107 NUT, STOVER LOCK, 3/4-10 UNC, GR.5, YELLOW ZINC PLATED 3 530-1266 BOLT, 3/4-10 UNC - 2.5, GR.8, YELLOW ZINC PLATED 4 533-6514 JAM NUT 7/8" -14 UNF 5 534-7914 FLANGE NUT 7/8" - 14 UNF 6 538-0815 BOLT, 1/2-20 UNF - 1, GR.8, YELLOW ZINC PLATED 7 550-5312 WASHER, FLAT, 3/4" - SAE, GR.5, YELLOW ZINC PLATED 8 551-5008 WASHER, SPRING, 1/2, GR.5, YELLOW ZINC PLATED 9 670-1001 ISOLATOR, RUBBER, TORSION 10 680-1007 DISC HUB ASSEMBLY AG-1418, 6 HOLES X 100MM 11 680-5006 DISC, 20" OD, 6 HOLE PATTERN,SMOOTH 12 839-1448 SHANK, ONE PIECE, UPPER CLAMSHELL Disc Gang, Finishing Shank 29

Roller Packers 30 Roller Packers

Roller Packers Item # Part # Qty Description 1* 105-0808 2 CHEVRON PACKER ROLLER, 16", LARGE 1* 105-0807 2 CHEVRON PACKER ROLLER, 16", MEDIUM 1* 105-0806 2 CHEVRON PACKER ROLLER, 16", SMALL 2* 105-1065 2 BASKET PACKER ROLLER, LARGE 2* 105-1064 2 BASKET PACKER ROLLER, MEDIUM 2* 105-1062 2 BASKET PACKER ROLLER, SMALL 3* 160-0571 2 RUBBER PACKER ROLLER, LARGE 3* 160-0573 2 RUBBER PACKER ROLLER, MEDIUM 3* 160-0575 2 RUBBER PACKER ROLLER, SMALL Roller Packers 31

Depth Spacers 32 Depth Spacers

Depth Spacers Item # Part # Description 1 105-0934 CENTER BRIDGE WELDMENT 1 105-0928 GANG LINK, WITH LUG 2 105-1066 HCD DEPTH SHIM ROD CLEVIS MACHINED 3 402-6049 STEEL COMPRESSION SPRING ZP 4 422-0022 STEEL CLEVIS PIN, YZP, W HAIRPIN AND LANYARD 5 526-6105 NUT, STOVER LOCK, 1/2-13 UNC, GR.5, YELLOW ZINC PLATED 6 550-5308 WASHER, FLAT, 1/2" - SAE, GR.5, YELLOW ZINC PLATED 7* 839-1724 HCD DEPTH ADJUST SHIM THIN 1/4" 7* 839-1725 HCD DEPTH ADJUST OFFSET SHIM THIN 1/4" 8 670-0044 CYLINDER, HYD - REPHASING 4.00" X 10", WELDED Depth Spacers 33

RAM 6 X 32 X 3 RAM PART NUMBER R4508223 RITE WAY PART NUMBER 670-0012 Item # Part # Description 1 R5508223 BARREL WELDMENT 2 R4208223 SHAFT WELDMENT 3 R4608223 PISTON 4 R4706575 GLAND 5 R3007202 SET SCREW, SOCKET, 3/8-16 UNC x 3/8 LG 6-13 R3608223 SEAL KIT 34 Cylinders

RAM 2-1/2 X 6 X 1-1/4 RAM PART NUMBER R4508157 RITE WAY PART NUMBER 670-0002 Item # Part # Description 1 R5507616 BARREL WELDMENT 2 R4208156A SHAFT 3 R6400045 PISTON 4 R6500013 GLAND 5 R3005005 LOCKNUT, 7/8-14 UNF, GRADE C 6 R7600455 CLEVIS 7 R3008022 HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R3005301 NUT, HEX, 3/8-16 UNC, GR 8 9-14 R3608157 SEAL KIT Cylinders 35

RAM 3 X 6 X 1-1/4 RAM PART NUMBER R4508220 RITE WAY PART NUMBER 670-0017 Item # Part # Description 1 R5508220 BARREL WELDMENT 2 R4208220A SHAFT 3 R6400048 PISTON 4 R6500020 GLAND 5 R3005006 LOCKNUT, 7/8-14 UNF, GRADE C 6 R7600455 CLEVIS 7 R3008022 HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R3005301 NUT, HEX, 3/8-16 UNC, GR 8 9-14 R3608220 SEAL KIT 36 Cylinders

RAM 3-1/2 X 8 X 1-3/4 RAM PART NUMBER R4508221 RITE WAY PART NUMBER 670-0017 Item # Part # Description 1 R5507647 BARREL WELDMENT 2 R4208221A SHAFT 3 R6400049 PISTON 4 R6500038 GLAND 5 R3005007 LOCKNUT, 1 1/4-12 UNS, GRADE C 6 R7600455 CLEVIS 7 R3008022 HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR 8 8 R3005301 NUT, HEX, 3/8-16 UNC, GR 8 9-14 R3608221 SEAL KIT Cylinders 37

RAM 4 X 10 X 2 RAM PART NUMBER R4508222 RITE WAY PART NUMBER 670-0018 Item # Part # Description 1 R5507663 BARREL WELDMENT 2 R4207663A SHAFT 3 R6400054 PISTON 4 R6500052 GLAND 5 R3005008 LOCKNUT, 1 1/8-12 UNF, GRADE C 6 R7600455 CLEVIS 7 R3008022 HEX CAP SCREW, 3/8-16 UNC x 2.0 LG, GR. 8 8 R3005301 NUT, HEX, 3/8-16 UNC, GRADE 8 9-14 R3608222 SEAL KIT 38 Cylinders

MONARCH 3-1/2 X 10 X 1-1/4 MONARCH PART NUMBER 659040 RITE WAY PART NUMBER 670-0042 1 2 3 4 Item # Part # Description 1 258827 Piston 2 497857 Rod 3 649216 Seal Kit 4 493830 Clevis Cylinders 39

MONARCH 3-3/4 X 10 X 1-3/8 MONARCH PART NUMBER 659041 RITE WAY PART NUMBER 670-0043 1 2 3 4 Item # Part # Description 1 258831 Piston 2 497860 Rod 3 649222 Seal Kit 4 493830 Clevis 40 Cylinders

MONARCH 4 X 10 X 1-3/8 MONARCH PART NUMBER 659042 RITE WAY PART NUMBER 670-0044 1 2 3 4 Item # Part # Description 1 258834 Piston 2 497860 Rod 3 649227 Seal Kit 4 493830 Clevis Cylinders 41

NOTES 42

NOTES 43