530.TGY (95) SINGLE PACKAGE GAS / ELECTRIC AIR CONDITIONERS DEG/DEE090, & DEG/DEE 7/, AND / NOMINAL TONS 9.5.0 EER SUNLINE PLUS DESCRIPTION YORK Sunline PLUS units are convertible single packages with a common footprint cabinet and common roof curb for all models. All units have dual compressors and dual independent refrigeration circuits. They provide high efficiency cooling and can be equipped with either gas heat or electric heat. The units were designed for light commercial applications and can easily be installed on a roof curb, slab, roof jack or frame. All units are selfcontained and assembled on rigid full perimeter base rails allowing for 3way fork lift access and overhead rigging. Every unit is completely charged, wired, piped and tested at the factory to provide for a quick and easy field installation. Both down and side discharge airflows are available without having to swap panels. The installer simply removes the duct covers for the desired configuration. Economizers may be used on either side or down discharge applications with no modifications required. All units have long lasting powder paint cabinets with 7 hour salt spray test approval under ASTMB7 procedures. All models include a year limited warranty on the complete unit. Compressors and electric heating elements carry an additional year warranty. Aluminized steel tubular heat exchangers carry an additional 9year warranty. FEATURES COMMON FOOTPRINT / COMMON CABINET All model sizes share the exact same footprint cabinet and therefore the same roof curb. You now have the flexibility of setting one curb and, after the internal load has been determined, placing the proper tonnage unit on that curb. HIGH EFFICIENCY All units have a minimum EER of 9.3. Gas/electric models have electronic spark ignition and power vented combustion with a minimum Steady State Efficiencies of 0%. These efficiencies exceed all legislated minimum levels and provide low operating costs. CONVERTIBLE AIRFLOW DESIGN Both the side and bottom duct openings are covered when they leave the factory. If a side supply / side return is desired, you simply remove the two side duct covers from the outside of the unit and discard them. If a bottom supply / return is desired, you simply remove the two bottom duct covers and discard them. No panel cutting or swapping is required! Convertible airflow design allows maximum field flexibility and minimum inventory. FACTORY INSTALLED OPTIONS Economizers and alternate indoor fan motors can be installed at the factory. The economizers are shipped installed and wired. Only the outdoor air hood needs to be field assembled and installed. PHENOLIC COATED CONDENSER COIL Special coating process that utilizes "Technicoat " processes. Coating is applied by total immersion of the complete coil for maximum protection. FIELD INSTALLED ACCESSORIES Accessories were designed for quick and easy installation. The motorized damper and economizers simply slide in, and electrical connections are made by modular plugs. The " high roof curb is shipped knocked down. The roof curb has an insulated deck. Low ambient controls are available to provide stable unit operation at outdoor temperatures down to 0 F. Propane and high altitude kits are also available to cover all gas heating applications. WIDE RANGE OF INDOOR AIRFLOWS Indoor fan motors are beltdrive type providing maximum flexibility to handle all airflow requirements. Factoryinstalled alternate indoor fan motors are available on some models for high static applications. A fixed outdoor air damper with rain hood is standard on all units. It must be fieldinstalled on either the return air duct cover for bottom air applications or on the return air ductwork for side air applications. The damper can be adjusted to allow up to 5% outdoor air to enter the unit s return air section. This same damper assembly can be used for barometric relief on units with economizer. FULL PERIMETER BASE RAILS The permanently attached base rails provide a solid foundation for the entire unit and protect the unit during shipment. The rails provide fork lift access from 3 sides, and rigging holes are also provided so that an overhead crane can be used to place the units on a roof. Cont d.
530.TGY FEATURES CONT D. UTILITY CONNECTIONS MADE EASY Gas and electric utility knockouts are provided in the bottom as well as the side of the unit. A clearly identified location is provided to mount a field supplied electrical disconnect switch. Utility connections can be made quickly and with a minimum amount of field labor. SIMPLE CONTROL CIRCUIT A low voltage printed circuit board contains a low voltage terminal strip. An additional set of pin connectors is also provided so that field interface of external controls will be simplified. The electrical control box is not located in the compressor compartment so the access cover can be removed for troubleshooting without affecting the normal system operating pressures. AIR FILTERS Units come standard with " throwaway filters. The unit filter racks can accommodate " or " filters without any modifications. SYSTEM PROTECTION Internal overload protection and crankcase heat are standard on all compressors. Each refrigeration circuit has a liquid line filterdrier, a discharge line high pressure switch and a suction line with a freezestat and low pressure/loss of charge switch to protect all system components. The units will operate down to 5 F without any additional low ambient controls. SUNLINE PLUS LONG LASTING POWDER PAINT FINISH ASTMB7 CERTIFIED WITH POST PURGE FULL PERIMETERBASE RAILS WITH FORKLIFT SLOTS AND LIFTING HOLES TABLE OF CONTENTS Description... Features... Ratings...3 Physical Data...3 Cooling Capacities... Blower Performance...9 Blower Motor and Drive Data...9 Field Wiring...9 Electrical Data... Accessory Static Resistances... Component Weights... Electrical Data Electric Heaters... Unit Dimensions... 3 Typical RoofTop Installation... Roof Curb Dimensions... 5 Typical Applications... 5 Options and Accessories... Unitary Products Group
530.TGY RATINGS CAPACITY RATINGS Cooling / Electric Heating MODEL ARI RATINGS COOLING CAPACITY 0 / 795 F MBH EER IPLV SOUND RATING 3 (bels) NOMINAL ELECTRIC HEAT CAPACITY (KW) DEE090 9.0. 9.0 9,,, 3 DEE.0.0 9.0,, 3, 5 DEE 9.5 9.0,, 3, 5 CAPACITY RATINGS Cooling / Gas Heating ARI RATINGS MODEL COOLING CAPACITY 0 / 795 F MBH EER IPLV DEG090N30 9.0. DEG090N5 9.0. DEGN5.0.0 DEGN00.0.0 DEGN5 9.5 9.0 DEGN00 9.5 9.0 NOTE: All units are twostage gas heating. First stage is % of total. Rated in accordance with ARI Standard. Rated in accordance with ARI Standard 30. 3 Sound ratings are in accordance with ARI Standard. SOUND RATING 3 (bels) 9.0 9.0 9.0 9.0 INPUT (MBH) 3 0 0 5 0 5 OUTPUT (MBH) 30 3 3 9 3 9 GAS HEAT CAPACITY S.S.E. (%) 0.0 0.0 0.0.0 0.0 0. S.E. (%) 7.9 7.9 73.5 7. 7.0 73. TEMP. RISE ( F) 30 0 30 0 30 0 30 0 30 0 30 0 GAS LINE SIZE (in. OD) 3/ 3/ 3/ 3/ 3/ 3/ EER = Energy Efficiency Ratio the cooling capacity in BTU s per hour (BTUH) divided by the power input in watts at any given set of rating conditions, expressed in BTUH per watt (BTUH/watt). S.S.E. = Steady State Efficiency. (Percent Output). S.E. = California Seasonal Efficiency determined in accordance with test procedures as specified by the State of California Energy Commission. PHYSICAL DATA BASIC UNITS EVAPORATOR EVAPORATOR COIL CONDENSER FANS (Two Per Unit) CONDENSER COILS (Two Per Unit) AIR FILTERS (SEE NOTE) SYSTEM CHARGE *Standard on DEG090 NOTE: Filter racks are adapted for " or " thick filters. MODELS DEG/DEE DEG/DEE 090 CENTRIFUGAL (Dia. x Wd. in.) x 5 x 5 X FAN MOTOR HP (STANDARD) / 3 FAN MOTOR HP (ALTERNATE) * 3 5 ROWS DEEP 3 FINS PER INCH 5 5 5 FACE AREA (Sq. Ft.) 7..9 3. PROPELLER DIA. (in.) (Each) FAN MOTOR HP (Each) / / 3/ NOM. (Each) 900 300 00 ROWS DEEP (Each) 3 3 FINS PER INCH (Each) 3 3 FACE AREA (Sq. Ft.) (Total).7.0 9.3 QUANTITY PER UNIT (" x " x ") QUANTITY PER UNIT (" X " X ") 3 QUANTITY PER UNIT (" X " X ") TOTAL FACE AREA (sq. ft.) 9.3.3.0 REFRIGERANT SYSTEM NO. 9/0 / / (lbs./oz.) SYSTEM NO. 9/0 / 3/0 Unitary Products Group 3
530.TGY COOLING CAPACITIES 7/ TON (DEG/DEE090) Air On Temperature of Air on Condenser Coil Evaporator 5 F 95 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7.9 0 9 7 7. 7 9 73 37 7 5 7. 9 9 7 75 53 9. 93 7 0 37 7. 3 9 0 9. 97 5 7 3 57 7.3 0 9 77 5. 5 5 5 9 3 7 0 7 7.0 9 7 7.0 9 7 5 3375 7 7.3 0 90 0 0 0 5. 97 7 77 7 57 7 3 9 7.3 9 9 9 7 5. 9 7 57 7. 5 95 5 75 5. 9 7 7 7 7. 9 73 5 5 3.0 90 7 3 5 3000 7 5 7.5 9 73 55 37. 9 0 7 3 5 5 3 3 7.5 3 3 9 9 0 7 0. 0 0 9 7 7 9 0 57 7.5 99 90 7 97. 97 97 97 79 7 7 7. 7 5 7.9 3 75 7 59 5 5 7 7.5 5 77 9 53 5 3 9.0 7 5 3 3 7. 3 0 9 7 97.0 97 95 9 73 5 5 57 7.5 99 95 7 79 7 3 95.0 95 9 9 3 75 7 59 7 7. 7 7 0 53 99 7. 7 9 5 9 7 7. 79 7 5 5 5 5 3 9.0 7 5 7 0 33 3 7. 3 9 90 3 7 9 95 7.9 95 90 3 7 9 55 57 0 7.5 0 9 9 77 3 93 7.9 93 9 77 7 57 Air On Temperature of Air on Condenser Coil Evaporator 5 F 5 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7.9 9 7 0 97 9. 97 9 0 9 5 37 7 0 9. 99 9 0 9 5 95. 9 9 7 7 5 33 9. 90 79 7 5 9. 9 9 9 3 7 9 57 99 9. 99 99 99 7 7 5 5 9. 9 9 9 9 5 7 7 9.7 9 5 75 5 55 90 9.3 90 7 5 3375 7 9.9 9 7 5 33 9. 7 7 5 3 95.9 95 95 9 75 5 55 7 9. 7 7 90 0 9 59 9 57 93.9 93 93 95 5 75 5 55 5 9.7 5 5 9 79 9 59 9 7 9. 77 59.9 73 55 3000 7 9.7 5 77 59 3 9. 73 55 37 9. 9 9 90 7 3 55 79 9. 79 79 5 7 7 5 9 57 7. 7 7 9 3 7 5 5 77 9. 77 77 77 9 0 5 7 90.3 7 5 0.7 73 5 57 9 5 7.5 77 9 53 5 37 9 7 9.0 7 5 0 33 5 7.5 7 3 75 7 59 5 77 9.0 77 77 7 0 5 57 5.5 5 5 7 0 5 75 9.0 75 75 77 9 5 7. 3 5 3 77. 57 5 37 7. 9 55 3 7 7.9 3 5 9 5. 5 75 5 7 75. 75 7 7 0 53 39 57 3. 3 7 9 3 5 9 73.9 73 73 5 7 These capacities are gross ratings. For net capacity, deduct the heat of the supply air blower motor, MBH = 3.5 x KW. Refer to the appropriate Blower Performance Table for the KW of the supply air blower motor. These ratings include the condenser fan motors (Total KW) and the compressor motors but not the supply air blower motor. NOMINAL RATING ALL SENSIBLE CAPACITY Unitary Products Group
COOLING CAPACITIES TON (DEG/DEE) Air On Temperature of Air on Condenser Coil Evaporator 5 F 95 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7 9.9 7 97 3.7 39 9 9 79 00 7 3 9.9 39 9 9 79 9 3.5 3 9 7 3 9.7 3 3 3 3 9 3 39. 39 39 39 9 9 79 57 0 9.7 0 0 0 9 3. 3 3 3 9 7 7 3 9.9 30 7 3 90 77 39. 7 0 7 39 9. 9 5 75. 3 99 73 59 3 9. 3 3 3 9 3. 3 3 3 9 7 57 3 9. 3 3 9 3. 3 3 3 5 9 7 7 3 9.9 7 95 3 7 3. 7 5 93 9 000 7 3 9.7 9 3 7 59 7 3. 7 5 93 9 57 5 33 9. 33 33 90 7 9. 9 9 0 7 57 3 9. 3 3 9 7 5 93 7. 7 7 7 5 3 9 79 7 37 9. 9 0 3.5 9 9 77 00 7 3 9.7 0 9 79 5 7.3 97 7 5 55 33 9.5 33 9 0 9 7 7. 7 95 5 7 57 30 9.5 30 9 3 3 9 5. 5 9 9 9 7 77 7 37 9. 5 9 7 7 9. 0 9 73 3 3000 7 3 9. 3 9 5 75 57 5. 9 9 0 5 3 33 9.5 33 5 97 79 5.0 5 9 0 90 7 57 30 9. 30 7 9 0 90 3.0 3 93 7 Air On Temperature of Air on Condenser Coil Evaporator 5 F 5 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7 37.5 3 93 7 3. 3 3 93 7 00 7 3. 3 5 90 75 0 5. 5 90 75 0 5 3.0 3 3 3 3 73.7 9 7 57 30.9 30 30 30 5 0 5. 9 9 79 7 3. 5 3 0 73 3. 99 5 7 0 7 7. 3 9 5 7 5 5. 97 57 3.9 7 0 7 73 9. 9 9 3 9 9 9 57.9 7 0 7 73 7.5 7 7 3 9 9 3 9 7. 5 3 9 0 5. 3 90 7 000 7 3.0 5 3 9 79 7 5.7 3 9 77 5. 9 7. 9 7 95 3 7 57. 0 9 77 9.5 9 9 9 9 7 7 3.3 95 5 7.0 3 93 7 00 7.0 5 9 73 5. 9 0 9 39 9. 9 7 3 9.5 9 9 77 7 57 7.7 7 5 5 9 73 9. 9 9 90 0 9 7. 97 7 7 9 0.0 93 7 5 5 3000 7 7.9 9 5 7 7 5 39.5 9 7 3 5 5 7.7 7 3 95 5 7 7. 99 90 0 7 57 5.7 5 97 7 9.3 9 3 73 These capacities are gross ratings. For net capacity, deduct the heat of the supply air blower motor, MBH = 3.5 x KW. Refer to the appropriate Blower Performance Table for the KW of the supply air blower motor. These ratings include the condenser fan motors (Total KW) and the compressor motors but not the supply air blower motor. 530.TGY NOMINAL RATING ALL SENSIBLE CAPACITY Unitary Products Group 5
530.TGY COOLING CAPACITIES / TON (DEG/DEE) Air On Temperature of Air on Condenser Coil Evaporator 5 F 95 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7 7. 5 9 9 7 7. 9 73 50 7. 5 37 7 5. 5 3 9 3 5.3 5 5 5 3 5. 9 3 9 0 57 5.3 5 5 5 9. 3 5 99 7 7. 5 9 7 7. 3 7 7 5 7. 3 9 3 7 7 57. 9 3 7 7 9.3 9 9 7 3 5 0 3. 3 3 3 7 9 0 57 9.3 9 9 9 3 7 3. 3 3 3 30 9 3 7 7.9 7 7 7 9. 5 0 5 00 7. 3 7 7 57. 3 7 7 7.3 7 97 3. 0 5 95 0 57.3 7 3 7 3. 3 9 3 7 9. 95.7 5 9 7 5 375 7 57. 3 95.3 33 93 0 7 3. 3 33 7 9 0 3.0 3 9 9 7 57 3. 3 3 3 5 9 5 3.0 3 3 3 5 9 79 7 3.5 99 7 7 5. 95 3 7 0 37 7.5 99 7 5 3. 9 7 9 73 3. 3 3 3 90 7 3.0 3 9 95 3 7 57 3. 3 3 9 7 9 3 3.0 3 3 9 97 7 Air On Temperature of Air on Condenser Coil Evaporator 5 F 5 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH WB Cap. Input Entering Dry Bulb, F Cap. Input Entering Dry Bulb, F F MBH KW 3 0 77 7 7 MBH KW 3 0 77 7 7 7 7 3. 7 5. 3 7 50 7 3. 3 99 3 30 3. 30 95 79 3 33. 33 33 33 0 7 3.5 7 7 5 57 33. 33 33 33 5 9 7 3.5 95 79 7 3 3. 5 9 5. 99 3 7 5 7 3 3. 39 9 3 9 3. 9 93 77 30. 30 30 30 99 3 7 7 3. 7 7 7 5 57 30. 30 30 30 9 3 7 7 3. 7 7 7 9 77 7 3.5 97 7. 9 9 79 5 00 7 3. 3 9 3.7 5 90 75 0 7. 7 7 97 3 7 3. 3 99 9 5 57 7. 7 7 7 7 3. 90 75 0 7 55 3. 9 7 3.3 0 7 73 0 375 7 3.0 75 3. 9 9 3 5 3.7 3 3 7 9 77 3.3 5 9 79 5 57 3.7 3 3 9 3.3 97 7 57 7 3.3 93 5. 9 79 7 5 37 7 9.9 5 3 9 0 57 3.5 99 7 75 5 9. 9 7 9 73 7 3. 7 97 5 7 5 57 9. 9 9 99 7 5 7 3. 7 7 90 7 7 55 These capacities are gross ratings. For net capacity, deduct the heat of the supply air blower motor, MBH = 3.5 x KW. Refer to the appropriate Blower Performance Table for the KW of the supply air blower motor. These ratings include the condenser fan motors (Total.3 KW) and the compressor motors but not the supply air blower motor. NOMINAL RATING ALL SENSIBLE CAPACITY Unitary Products Group
PERFORMANCE (7/, & / TON SUPPLY AIR) MODEL DEG090 (SIDE DUCT APPLICATIONS) RPM 5 3000 300 37 ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 975 0.3..0 0..7. 0.37.5. 0.0.5.5 5 0.9..3 0..3.5 0.5.5. 0..75.3..3.3 0.95..3 0.7..57 0.37.9.7 0.07..97 30.3.3.33..57. 0..3.7 0.5.0.90 75.5.5..3.7.5.07.9.79 0.75..03...55.53..9.3..9 MODEL DEG090 (BOTTOM DUCT APPLICATIONS) 5 3000 300 37 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 975 0.7..0 0.57.7. 0..5. 5 0.9..3 0.73.3.5 0.39.5. 0.0.75.3.05.3.3 0...3 0.5..57 0.0.9.7 30..3.33.07.57. 0.73.3.7 0.39.0.90 75..5..7.7.5 0.9.9.79 0.5..03...55...9...9 MODEL DEG (SIDE DUCT APPLICATIONS) RPM 3000 00 000 0 00 ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 0.05.0.3 0.5.5. 0..0. 0.3.05.9 95.3.55.5.05.7. 0.0.9.5 0.5.3.0 0...3 9...57..9.7.00..00 0..3.7 0.0.7.5 00.0.3.7..07.93.0.33.7 0.93..5 0.5.9.7.0.9..5.5...55.37...7 0.5 3.7.9 90.99..97....3.7.5.3 3.0. MODEL DEG (BOTTOM DUCT APPLICATIONS) RPM 3000 00 000 0 00 ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 0 0.9.0.3 0.7.5. 0.39.0. 0.0.05.9 95..55.5 0.7.7. 0.57.9.5 0..3.0 9.9..57.0.9.7 0.77..00 0.0.3.7 0.0.7.5 00.7.3.7..07.93 0.97.33.7 0.3..5 0.9.9.7.7.9..7.5..9.55.37 0...7 0.9 3.7.9 90...97....0.7.5.0 3.0. MODEL DEG (SIDE DUCT APPLICATIONS) RPM 000 0 00 50 000 ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 90.00..00 0..3.7 0.0.7.5 0. 3.03.3 00.0.33.7 0.93..5 0.5.9.7 0. 3. 3.03 0..0 3.9..55.37...7 0.5 3.7.9 0..0 3.79 0.39.53. 90.3.7.5.3 3.0.. 3.7 3.53 0.7. 3.99 0.5.79. 5.7 3.0.7.7 3.5 3.. 3. 3. 0.5..0 0..9.5 0.9 3.5 3.03.3 3. 3... 3.3.0.53. 0.5 5..77 MODEL DEG (BOTTOM DUCT APPLICATIONS) RPM 530.TGY 000 0 00 50 000 ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 90 0.77..00 0.0.3.7 0.0.7.5 00 0.97.33.7 0.3..5 0.9.9.7.9.55.37 0...7 0.9 3.7.9 0..0 3.79 90.0.7.5.0 3.0. 0.7 3.7 3.53 0.. 3.99 0..79. 5.5 3.0.7.7 3.5 3. 0. 3. 3. 0.9..0 0..9.5 0. 3.5 3.03.33 3. 3. 0.99. 3.3 0..53. 0.5 5..77 NOTES:. Blower performance includes a wet evaporator coil and " filters.. Blower performance includes the maximum number of heat exchangers. = Larger Horsepower Alternate Motor Required. 3. Refer to page for the resistance of the unit accessories. ESP = External Static Pressure available for the supply and return air duct sytem. All internal unit resistances have been deducted from the total static pressure of the blower. Unitary Products Group 7
530.TGY PERFORMANCE (7/, & / TON SUPPLY AIR) MODEL DEE090 (SIDE DUCT APPLICATIONS) 5 3000 300 37 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 975 0.93..0 0.79.7. 0.53.5. 0.9.5.5 5.0..3 0.95.3.5 0..5. 0..75.3 0.7.97...3.3.0..3 0.3..57 0.5.9.7 0.3..97 30..3.33.9.57..0.3.7 0.77.0.90 75..5..9.7.5.3.9.79 0.9..03.7..55...9.39..9 MODEL DEE090 (BOTTOM DUCT APPLICATIONS) 5 3000 300 37 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 975 0...0 0..7. 0.0.5. 0..5.5 5.0..3 0..3.5 0.55.5. 0.5.75.3.5.3.3 0.99..3 0...57 0..9.7 0...97 30.3.3.33.0.57. 0.9.3.7 0.0.0.90 75.5.5..0.7.5..9.79 0.79..03.7..55.57..9...9 MODEL DEE (SIDE DUCT APPLICATIONS) 3000 00 000 0 00 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 0..0.3 0.9.5. 0.77.0. 0.53.05.9 0.5.3.5 95.3.55.5..7. 0.95.9.5 0.7.3.0 0.9..3 9.5..57.37.9.7.5..00 0.9.3.7 0.7.7.5 00.9.3.7.57.07.93..33.7...5 0.9.9.7.9.9..7.5..57.55.37...7. 3.7.9 90.0..97.97...7.7.5.55 3.0. MODEL DEE (BOTTOM DUCT APPLICATIONS) 3000 00 000 0 00 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 0.0.0.3 0.0.5. 0.5.0. 0.3.05.9 95.9.55.5.00.7. 0.7.9.5 0..3.0 0.3..3 9.3..57.9.9.7 0.9..00 0..3.7 0.3.7.5 00.5.3.7.39.07.93..33.7 0...5 0.5.9.7.7.9..0.5..3.55.37.05..7 0.7 3.7.9 90.95..97.79...55.7.5.5 3.0. MODEL DEE (SIDE DUCT APPLICATIONS) 000 0 00 50 000 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 90.5..00 0.9.3.7 0.7.7.5 0.3 3.03.3 0. 3.9 3.7 00..33.7...5 0.9.9.7 0. 3. 3.03 0..0 3.9.57.55.37...7. 3.7.9 0.9.0 3.79 0.9.53. 90.7.7.5.55 3.0..37 3.7 3.53.05. 3.99 0..79. 5.9 3.0.7. 3.5 3..5 3. 3....0 0.9.9.5 0.0 3.5 3.03. 3. 3... 3.3.9.53..5 5..77 Unitary Products Group
PERFORMANCE (/ TON SUPPLY AIR continued) 530.TGY MODEL DEE (BOTTOM DUCT APPLICATIONS) 000 0 00 50 000 RPM ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW ESP BHP KW 90 0.9..00 0..3.7 0.3.7.5 0.0 3.03.3 00..33.7 0...5 0.5.9.7 0. 3. 3.03.3.55.37.05..7 0.7 3.7.9 0.53.0 3.79 0.7.53. 90.55.7.5.5 3.0..0 3.7 3.53 0.9. 3.99 0..79. 5. 3.0.7.3 3.5 3..09 3. 3. 0.7..0 0.5.9.5 0.3 3.5 3.03.5 3. 3... 3.3 0.93.53. 0.73 5..77 MOTOR AND DRIVE DATA MODELS RANGE (RPM) HP SERVICE FACTOR MOTOR* FRAME SIZE EFFICIENCY (%) ADJUSTABLE MOTOR PULLEY PITCH BORE DIA. (IN.) (IN.) FIXED PULLEY PITCH BORE DIA. (IN.) (IN.) PITCH LENGTH (IN.) BELTS DESIG NATION DEE090 /, 975 DEG090.0 5.0 3.. 7/..3 A9 DEE, 3 DEG 090 DEE 3 DEG.0 5.0 3.. 7/ 7.0 57.3 A5 DEE BX 900 5.5.0.9 5.9 /.9. DEG (Notched) * All motors are 7 RPM, have solid bases and are inherently protected. These motors can be selected to operate into their service factor because they are located in the moving air, upstream of any heating device. QTY. FIELD WIRING Unitary Products Group 9
530.TGY ELECTRICAL DATA (DEG) MODEL DEG 090 POWER SUPPLY 0/3030 030 57530 0/3030 030 57530 0/3030 030 57530 COMPRESSOR (# and #) RLA EACH. 7. 5. 9.5.0 7.9 0.7.0. LRA EACH 30 5 3 5 5 OUTDOOR FAN MOTOR, (# & #) FLA EACH.3.3.3.3.3.3 3.5.5.5 SUPPLY AIR MOTOR, FLA TOTAL UNIT AMPACITY, AMPS MAX. FUSE SIZE, AMPS MIN. WIRE SIZE,3 AWG HP 3HP 5 HP HP 3HP 5 HP HP 3HP 5 HP 7.5 3..7 7.5 3..7.. 3.9.. 3.9 NOTES:. Dual numbers shown as "./7.3" amps indicates compressor #/#, respectively.. Dual element, time delay type. Amps shown as "0/5" indicates rating for LO HP/HI HP, respectively. Maximum HACR breaker of the same AMP size is applicable. 3. Based on 75 C copper conductors. 5. 7.5 5.9 3..9.3 5.0.5 3. 59. 9.9.3. 3.3 7..7.0 9. 5 0 30 0 0/5 VOLTAGE POWER SUPPLY MIN. MAX. VOLTAGE 0/3030 7 53 LIMITATIONS* 030 57530 5 30 *Utilization Range A in accordance with ARI Standard. ELECTRICAL DATA (DEE) MODEL DEE 090 POWER SUPPLY 0/3030 030 57530 0/3030 030 57530 0/3030 030 57530 COMPRESSOR (# and #) RLA EACH. 7. 5. 9.3.0 7.9 0.7.0. LRA EACH 30 5 3 5 5 OUTDOOR FAN MOTOR, (# & #) FLA EACH.3.3.3.3.3.3 3.5.5.5 SUPPLY AIR MOTOR, FLA TOTAL UNIT AMPACITY, AMPS MAX. FUSE SIZE, AMPS MIN. WIRE SIZE,3 AWG /HP HP 3HP 5 HP / HP HP 3HP 5 HP /HP HP 3HP 5 HP 5.7.. 7.5 3..7 7.5 3..7.. 3.9.. 3.9 5. 7.5 5.9 NOTES:. Dual numbers shown as "./7.3" amps indicates compressor #/#, respectively.. Dual element, time delay type. Amps shown as "0/5" indicates rating for LO HP/HI HP, respectively. Maximum HACR breaker of the same AMP size is applicable. 3. Based on 75 C copper conductors..0. 7.7 3..9.3 55.5.5 3. 5. 9.9.3. 3.3 7..7.0 9. 5 0 30 0 0/5 VOLTAGE POWER SUPPLY MIN. MAX. VOLTAGE 0/3030 7 53 LIMITATIONS* 030 57530 5 30 *Utilization Range A in accordance with ARI Standard. Unitary Products Group
530.TGY ACCESSORY STATIC RESISTANCES* EXTERNAL STATIC PRESSURE DROP RESISTANCE, IWG MODELS DESCRIPTION 3000 000 00 000 DEE DEG Economizer/Motorized Damper 0.0 0.0 0.03 0.05 0.07 9 KW** KW 0.0 0. 0.0 0.3 0.5 DEE Electric Heaters KW 0. 0. 0.33 0. 3 KW 0.07 0.3 0.3 0. 0.5 5 KW*** 0.5 0. 0.0 0.5 *Deduct these resistance values from the available unit external static pressure shown in the respective Blower Performance Table. **9 KW Heater is only available on 7/ and / Ton Units. ***5 KW Heater is only available on and / Ton Units. COMPONENT WEIGHTS Basic Unit Options and Accessories NOTE: Weights are given in pounds. COMPONENT MODELS DEE & DEG 7/ TON TON / TON DEE (Cooling only) 00 0 30 Mbh 0 DEG (Gas / Electric) 5 Mbh 0 0 00 Mbh Economizer 77 77 77 Motorized Outdoor Air Damper 75 75 75 Oversized Motor 5 9 KW 9 Electric Heat KW (Nominal KW) KW 7 7 7 (DEE only) 3 KW 30 30 30 5 KW 37 37 Roof Mounting Curb 55 55 55 Unitary Products Group
530.TGY ELECTRICAL DATA Cooling / Electric Heating (DEE090, & ) UNIT SIZE, DEE 090 7/ TON UNIT with / OR HP TON UNIT with OR 3 HP TON UNIT with 3 OR 5 HP POWER SUPPLY SUPPLY AIR FLA MOTOR HP 030 5.7 7.5 ACCESSORY ELECTRIC HEATERS TOTAL UNIT AMPACITY, AMPS MOTOR HP MAXIMUM FUSE SIZE,, AMPS MINIMUM WIRE SIZE,3 AWG MOTOR HP LO HI MODEL NO. KW STAGES TOTAL AMPS LO HI LO HI LO HI HE0595...0 3. HE055 3.5 37.5 5.0 5.3 0 0 HE055.0.0 9.7 7.9 0 HE05 7.0 75. 0.9 3. 3030 5.7 7.5 030. 3. 57530..7 030 7.5. 3030 7.5. 030 3.. 57530.7 3.9 030. 5. 3030. 5. 030. 7.5 57530 3.9 5.9 HE0595 HE055 HE055 HE05 HE059* HE05* HE05 HE053 HE0595 HE055 HE055 HE05 HE055 HE055 HE05 HH0555 HE055 HE055 HE05 HH0555 HE05* HE05 HE053 HE055 HE055 HE055 HE05 HE0555 HE055 HE055 HE05 HH0555 HE055 HE055 HE05 HH0555 HE05* HE05 HE053 HE055 HE055 HE055 HE05 HE0555 9.0.0.0 3.0 9.0.0.0 3.0 9.0.0.0 3.0 3.5.0 7.0 0..0.0 3.0 5.0.0.0 3.0 5.0.0.0 3.0 5.0 3.5.0 7.0 0..0.0 3.0 5.0.0.0 3.0 5.0.0.0 3.0 5.0 Dual element, time delay type. Maximum HACR breaker of the same AMP size is applicable, except 575 voltages. Standard circuit breakers may be used in Canada and on applications over 0 amps where the heaters are separately fused. 3 Based on 75 C copper conductors. *These electric heaters do NOT include fuses. If fuses are required to meet a local code (eg. Chicago), an accessory fuse box with fuses (FB003) is available for field installation..7 3.3 57.7...7.9 3.3.7 7.3 3. 3. 37.5.0 75.. 3.3 57.7. 9.9.7.9 3.3 5.0 7.3 3. 3. 5.0 37.5.0 75.. 3.3 57.7. 9.9.7.9 3.3 5.0 7.3 3. 3. 5.0.0.3 79.3 5.. 30.3 39.3 57. 7.7.3 3.5 5.9 5.3 7.9 3.. 3.5.5 7. 39.3 3.3 0.3 5. 9. 5.0 3..7 55.3. 75. 7. 5.0 7. 5..5 3. 7.. 0. 7.0 33. 33.7. 5. 3. 3.5.5 7..9 3.3 0.3 5..3 5.0 3..7 0. 75. 7. 5.0 7. 5..5 3. 33.. 0. 7.0.5 33.7. 5..7..7 59. 73.0 9.0 7.. 9. 5.5 3.5 7.3 3. 3..7 59.3 0 5 5 0 0 0 5 0 0 75 90 5 5 0 0 30 0 0 0 75 0 90 5 75 0 0 5 90 5 5 5 0 0 30 0 75 90 5 75 5 0 30 0 90 5 75 0 0 75 0 90 5 0 00 0 00 3 0 00 3 0 00 3 0 ELECTRIC HEAT CORRECTION FACTORS NOMINAL VOLTAGE VOLTAGE KW CAP. MULTIPLIER 0 0.00 0 30 0.9 0 0 0.9 00 575 0.9 Unitary Products Group
530.TGY UNIT DIMENSIONS (DEG/DEE 7/, & / TON) 337/ (090) All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request. DEG model shown UTILITIES ENTRY DATA HOLE OPENING SIZE (DIA.) USED FOR A 3/" KO Control Side 7/" KO Wiring Bottom B " KO Power Wiring (Side or Bottom) C " KO Gas Piping (Front) D /" Hole Gas Piping (Bottom), Openings in the bottom of the unit can be located by the slice in the insulation. 3/" Gas Piping MPT Required RETURN AIR SUPPLY AIR CONDENSER AIR OUTDOOR AIR (Economizer) CLEARANCES Front " " (Less Economizer) Back 3" (With Economizer) " (Less Economizer) Left Side (Filter Access) 5" (With Economizer) Right Side (Cond. Coil) " Below Unit 0" 7" With 3" Maximum Horizontal Above Unit Overhang (For Condenser Air Discharge) Units may be installed on combustible floors made from wood or class A, B or C roof covering material. Units must be installed oudoors. Overhanging structures or shrubs should not obstruct condenser air discharge outlet. NOTE: A " clearance must be provided between any combustible material and the supply air ductwork for a distance of 3 feet from the unit. The products of combustion must not be allowed to accumulate within a confined space and recirculate. Locate unit so that the vent air outlet hood is at least: Three (3) feet above any forced air inlet located within horizontal feet (excluding those integral to the unit). Four () feet below, horizontal feet from, or foot above any door or gravity air inlet into the building. Four () feet from electric meters, gas meters, regulators and relief equipment. DUCT COVERS Units are shipped with all air duct openings covered. For side duct applications;.remove and discard the supply and return air duct covers..connect ductwork to duct flanges on the rear of the unit. For bottom duct applications;. Remove the side supply and return air duct covers to gain access to the bottom supply and return air duct covers.. Remove and discard the bottom duct covers. 3. Replace the side duct covers. DETAIL X SIDE SUPPLY AND RETURN AIR DUCT OPENINGS Unitary Products Group 3
530.TGY UNIT DIMENSIONS CONT D. (DEG/DEE 7/, & / TON) DETAIL Y UNIT WITH ECONOMIZER AND FIXED OUTDOOR AIR HOODS DIM. UNIT 7/ TON TON / TON A 33/" 3/" 3/" B 7/" 3/" 5" TYPICAL ROOFTOP INSTALLATION CENTER OF GRAVITY NOTE: Power wiring, control wiring, and gas piping points of entry into the cabinet (side or bottom) must be sealed to prevent rain water entry ino the building. Unitary Products Group
ROOF CURB DIMENSIONS (DEG/DEE 7/, & / TON) 530.TGY *Supply and Return Air (including duct support rails) as shown, are typical for bottom duct applications. For location of horizontal duct applications (on back of unit), refer to Unit Dimension details. ROOF CURB BENEFITS UNIT AND CURB APPLICATION Field Installed ➀ The " space between the ducts allows for jumping an existing roof joist. ➁ The " overall dimension of the ducts allows ductwork penetration between roof joists that are spaced on " centers. NOTE: Ducts can be installed onto the curb from the roof. All electrical and gas line connections can be made inside the curb. TYPICAL APPLICATIONS Roof penetration cut out for supply and return duct only to minimize noise transmission into building. Unitary Products Group 5
FACTORY INSTALLED OPTIONS ECONOMIZERS: Units equipped with the factoryinstalled economizer option have dampers that are positioned by a spring return, fully modulating damper actuator capable of introducing up to 0% outdoor air. As the outdoor air intake dampers open, the return air dampers close. The changeover from mechanical refrigeration to economizer operation is determined by a single input electronic enthalpy control or by a dual input electronic enthalpy control. Simultaneous compressor and economizer operation is also possible. Economizer dampers are % low leakage type. A barometric relief damper is shipped in the return air compartment for field installation. The single enthalpy system contains a sensor that monitors the outdoor air which automatically operates the damper actuator allowing the dampers to open or close. The dual enthalpy system contains a second sensor that monitors the return air in addition to monitoring the outdoor air described above for a single enthalpy system. The logic module compares these two values and modulates the dampers providing the maximum efficiency of the economizer system. The economizer is completely wired and installed at the factory. Only the outdoor air hood, including its filters, need be assembled and installed in the field. ALTERNATE INDOOR FAN MOTORS: Larger horsepower motors are available on and / ton models to handle higher static pressure applications. PHENOLIC COATED CONDENSER COIL Special coating process that utilizes "Technicoat " processes. Coating is applied by total immersion of the complete coil for maximum protection. FIELDINSTALLED ACCESSORIES SINGLE INPUT ELECTRONIC ENTHALPY ECONOMIZER Includes a slidein / plugin damper assembly with fully modulating spring return motor actuator capable of introducing up to 0% outdoor air, one outdoor air electronic enthalpy sensor and a rainhood with filters. The rainhood is painted to match the basic unit and must be fieldassembled before installation. Economizer dampers are % low leakage type. The fixed outdoor air damper (shipped as standard equipment with every unit) can be used for barometric relief on units with an economizer. DUAL INPUT ELECTRONIC ENTHALPY ECONOMIZER Includes the same damper system and rainhood with filters as described for a single enthalpy economizer above except this accessory contains two enthalpy sensors. It uses a differential enthalpy control that compares the outdoor air versus the return air. The logic module then optimizes the economizer operation for additional savings over the single input economizer. The fixed outdoor air damper (shipped as standard equipment with every unit) can be used for barometric relief on units with an economizer. MOTORIZED AIR DAMPER Includes slidein / plugin damper assembly with position springreturn motor actuator and a rainhood with permanenttype filters. The outdoor air dampers open when the indoor fan motor is energized. The rainhood is shipped knocked down and must be field assembled. ELECTRIC HEATERS Include nickel chromium elements, a terminal block, fuses (where required by UL), all the necessary connectors and hardware. All heaters utilize single point power supply hookup. Capacities of 9,,, 3 and 5 KW heating are available. FUSE BLOCK KIT This kit contains a fuse block including the fuses and is available for the 9 and KW 0volt heater kits. This kit satisfies the Chicago code requirements. ROOF CURB This " high full perimeter roof curb is shipped knocked down for field assembly. Its duct supports and insulated condensing section deck can be reversed to connect the ductwork on the opposite end. LOW AMBIENT KIT Head pressure controllers maintain stable operation by reducing the speed of the condenser fan motors when the outdoor temperature is between 5 and 0 F. Condenser fan motors with ball bearings and heavier windings are available for these low ambient applications. ANTIRECYCLE TIMER A timer to prevent unit compressors from short cycling. It assures a 5minute "offtime" between compressor cycles. PROPANE CONVERSION KIT Converts a gasfired heater from natural gas to propane. It contains main burner orifices, a pilot orifice and a gas valve. GAS PIPING This kit contains 3/" pipe nipples, fittings and gas cock (including panel access gaskets) required for bottom gas supply connection with external shutoff. HIGH ALTITUDE CONVERSION (NATURAL AND PROPANE) Provides orifices for proper furnace operation at altitudes up to,000 ft. For propane applications, the propane conversion kit will also be required. WALL THERMOSTAT The units are designed to operate with volt electronic and electromechanical thermostats. All units operate with two stage heat / two stage cool thermostats (with or without an economizer). 7/ & TON / TON Unitary Products Group P.O. Box 59, York, Pennsylvania USA 559 Subject to change without notice. Printed in U.S.A Copyright by York International Corporation 995. All Rights Reserved.. Codes: EBY,EGY 530.TGY Supersedes: 530.TGY (9)