NEW High Pressure filters FMM 50 series Maximum pressure up to 0 bar - Flow rate up to 50 l/min PASSION TO PERFORM
FILTER SIZING THE CORRECT FILTER SIZING HAVE TO BE BASED ON THE TOTAL PRESSURE DROP DEPENDING BY THE APPLICATION. THE MAXIMUM TOTAL PRESSURE DROP ALLOWED BY A NEW AND CLEAN HIGH PRESSURE PRESSURE FILTER HAVE TO BE IN THE RANGE 0.8.5 bar. The pressure drop calculation is performed by adding together the value of the housing with the value of the filter element. The pressure drop pc of the housing is proportional to the fluid density (kg/dm ); all the graphs in the catalogue are referred to mineral oil with density of 0.86 kg/dm. The filter element pressure drop pe is proportional to its viscosity (mm /s), the corrective factor Y have to be used in case of an oil viscosity different than 0 mm /s (cst). Sizing data for single filter element, head at top pc = housing pressure drop [bar] pe = element pressure drop [bar] Y = Corrective factor Y (see correspondent table), depending on the filter type, on the filter element size, on the filter element lenght and on the filter media Q = flow rate (l/min) V reference oil viscosity = 0 mm /s (cst) V = operating oil viscosity in mm /s (cst) element pressure drop calculation with an oil viscosity different than 0 mm /s (cst) pe = Y : 000 x Q x (V:V) p Tot. = pc + pe Verification formula p Tot. p max allowed Maximum total pressure drop ( p max) allowed by a new and clean filter Application Range (bar) Suction filters Return filters Low & Medium Pressure filters High Pressure filters Stainless Steel filters 0.08 0.0 0. 0.6 0. 0.6 return lines 0. 0.5 lubrication lines 0. 0. off-line in power systems 0. 0. off-line in test benches 0. 0.6 over-boost 0.8.5 0.8.5 Calculation: pc = 0. bar (see graphic below) p bar Δ.50.00 0.50 housings p pressure drop. The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. pe = (5.9 : 000) x 0 x (6 : 0) =.09 bar FMM50 corrective factor Corrective factor Y to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference oil viscosity 0 mm /s Absolute filtration Nominal filtration element N - R Series Type A0 A06 A0 A6 A5 M5 HP 50 * FMM 50 0.00 0 50 00 50 00 50 00 50 Flow rate l/min 7.5 8.60 6.5 5.9 8.7 5.90 p Tot. = 0. +.09 =.9 bar 7.8.5.9 6.96.8.79 5.9.5..07 0.58 0.9 / The selection is correct because the total pressure drop value is inside the admissible range for high pressure filters. In case the allowed max total pressure drop is not verified, it is necessary to repeat the calculation changing the filter lenght. FMM50 calculation example Application data: High pressure filter Pressure Pmax = 00 bar Flow rate Q = 0 l/min Viscosity V = 6 mm /s (cst) Oil density = 0.86 kg/dm Required filtration efficiency = 5 μm with absolute filtration With bypass valve and / inlet connection
Corrective factor FILTER SIZING Corrective factor Y to be used for the filter element pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference oil viscosity 0 mm /s High pressure filters element Type HP 0 A0.7 0.8. 77.76 Absolute filtration N - R Series A06 A0 A6 50.07 65.56 9.68 58.5 8. 7.08.8 8.7 5.6 59..08.67 A5 8.6 7.05 0.7 6.7 Nominal filtration M5 - - - - HP 09 70.66 6.57 6.57 5.0.8.7 5.77 8.00.6 0.57.8 8.80.67 8.00 5.58.90.90.0 HP 050 5.75.5 7.7. 7.00 0.0.6 6.5 0.75 6.56.6.70 8.90 6.0.60. 9.09 7.8 5.75.0 7.9.90.6.08.5.60.0.5.07 0.80 HP 065 58.50.60 0.50.6 5.6 5.88.6 6. 8.8 9.66.88 6.8 0.7 7..9.8. 0.58 HP 5 0.. 6.8 8.80 0.6 6. 9.7 6.60.8 8.66 6.8.6.78...78..0 HP 50 7.5 8.60 6.5 5.9 8.7 5.90 7.8.5.9 6.96.8.79 5.9.5..07 0.58 0.9 HP 0 0.88.0.75. 9.7.8..77 5.0.75.05 0.98.7.8 0.87 0.78.5 0.88 0.77 0.55.0 0.7 0.6 0.7 HP 500 5..7..8..67.77.98..5.0.78. 0.9 0.77.0.68.09 0.86 0.68.65. 0.75 0.68 0.8 0.5 0.0 0.08 0.05 0.0 element Type A0 Absolute filtration A06 A0 A6 A5 Nominal filtration M5 HF 0.65.0.8.95.7..80.6..80.5. 0.90 0.85 0.80 0.8 0.6 0.5 Recommended maximum flow rate for complete FMM50 filter - Pressure drop of complete filter = p.5 bar - Reference oil viscosity 0 mm /s (cst) - Oil density 0.86 kg/dm - Connections of filter under test G / lenght A0 80 70 Flow rate (l/min) Filtration rating A06 A0 88 57 5 6 80 A6 6 5 A5 80 8 6
FMM50 Technical data GENERAL INFORMATION High Pressure filters Maximum pressure up to 0 bar - Flow rate up to 50 l/min housing materials - Head: Painted cast iron - Housing: Painted steel - Bypass valve: Steel Bypass valve - Opening pressure 600 kpa (6 bar) - Other opening pressures on request. Seals - Standard NBR series A - Optional FPM series V Pressure - Working pressure: MPa (0 bar) - Test pressure: 6 MPa (60 bar) - Burst pressure: 6 MPa (60 bar) - Pulse pressure fatigue test: 000 000 cycles with pressure from 0 to MPa (0 bar) p element type - Microfibre filter elements - series N: 0 bar - Wire mesh filter elements - series N: 0 bar - Fluid flow through the filter element from OUT to IN Temperature From -5 C to +0 C Connections In-line Inlet/Outlet Note FMM 50 filters are provided for vertical mounting Weights [kg] and volumes [dm ] Weights [kg] Lenght 5 FMM 50 7.50 9.50 0.90 - - Lenght Volumes [dm ] 5 0.60.00.5 - - Hydraulic symbols Style S Style B Pressure drop The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. housings p pressure drop Bypass valve pressure drop.50 FMM 50 FMM 50 5.00 / 0 Δ p bar p bar 0.50 Δ 5 0.00 0 50 00 50 00 50 00 50 Flow rate l/min 0 0 50 00 50 00 50 00 50 Flow rate l/min
FMM50 Designation & Ordering code COMPLETE FILTER Series and size Configuration example: FMM50 B A D M5 N P0 FMM50 Length Valves S B Seals A V Without bypass With bypass 6 bar NBR FPM Connections C G D G / E NPT F / NPT G SAE 6-5/6 - UN H SAE 0-5/8 - UN Connection for differential indicator Without connection Upper connection Frontal connection Filtration rating (filter media) A0 Inorganic microfiber µm A06 Inorganic microfiber 6 µm A0 Inorganic microfiber 0 µm A6 Inorganic microfiber 6 µm A5 Inorganic microfiber 5 µm M5 Wire mesh 5 µm Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized FILTER ELEMENT Element series and size HP50 Configuration example: HP50 M5 A N P0 Element length Filtration rating (filter media) A0 Inorganic microfiber µm A06 Inorganic microfiber 6 µm A0 Inorganic microfiber 0 µm A6 Inorganic microfiber 6 µm A5 Inorganic microfiber 5 µm M5 Wire mesh 5 µm Seals A V NBR FPM Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized Differential indicators DEA Electrical differential indicator DEM Electrical differential indicator DLA Electrical / visual differential indicator DLE Electrical / visual differential indicator ACCESSORIES DTA DVA DVM Visual differential indicator Electronic differential indicator Visual differential indicator Additional features T Plug
FMM50 Dimensions FMM50 length Connections C-D E-F-G-H H [mm] 0 0 5 R M0 /8 UNC Recommended clearance space for maintenance
FMM50 SPARE PARTS Order number for spare parts d e a b c f Item: series FMM 50 Q.ty: pc. Q.ty: pc. Seal Kit code number element NBR FPM See order table 00507 00507 Q.ty: pc. (a f) Indicator connection plug NBR FPM TH TV All data, details and words contained in this publication are provided for information purposes only. MP Filtri reserves the right to make modifi cations to the models and versions of the described products at any time for both technical and / or commercial reasons. The colors and the pictures of the products are purely indicative. Any reproduction, partial or total, of this document is strictly forbidden. All rights are strictly reserved.
WORLDWIDE NETWORK HEADQUARTERS MP Filtri S.p.A. Via Maggio, 0060 Pessano con Bornago Milano - Italy BRANCH OFFICES MP Filtri U.K. Ltd. Bourton Industrial Park Bourton on the Water GL5-HQ Gloucestershire MP Filtri Canada Inc. 88 Keele Street Concord, Ontario LK N - Canada MP Filtri Germany GmbH Hans-Wilhelmi-Straße DE-6686 St. Ingbert ITALFILTRI LLC Russian Federation Yurievsky Pereulok a, Building 00 Moscow - Russia MP Filtri France SAS Parc d activités des Chanteraines 8 rue du Commandant d Estienne d Orves Immeuble D 990 Villeneuve la Garenne MP Filtri (Shanghai) Co., Ltd. 80 Lianxi Road, Bld 8 - nd Floor Shanghai - Pudong 00 China MP Filtri U.S.A. Inc. 055 Quaker Pointe PA 895 Drive Quakertown MP Filtri India Pvt. Ltd. Plot-7F, Raj Pinnacle, Beside RMZ Centennial Brookefield Road, Whitefield 56008 Bangalore PASSION TO PERFORM mpfiltri.com CMPAEN006A Rev. 09-08