Type Series Booklet Elite Centrifugal Pump Application The Ajax Elite centrifugal pump is suitable for handling water and similar liquids mainly used in the following applications. -Water Supply -Air conditioning -Irrigation -Pressure boosting -Fire Protection -Heating and ventilating -Industrial Designation E 150-40 A 20 C Type Discharge diameter mm Nominal impeller diameter cm Mechanical arrangement Shaft sealing Materials of construction Design Horizontal, single stage, end suction centrifugal pump, complying with the requirements of EN 733 (DIN 24255). The back pull out design allows for easy maintenance and repair as the rotating element may be removed without disturbing the system pipework. Removal of the rotating element is facilitated by the lifting eye on the bearing housing. Operating Data 50Hz 60Hz Pump sizes 32mm to 250mm Flow up to 340L/s 288L/s Head up to 140m 108m Temperature up to 95 o C Speed up to 2900 rpm 3600 rpm Pressure up to 1600kPa KSB Australia Pty Ltd
Selection Chart 1450 rpm Note: For final selection refer to individual performance curves Selection Chart 2900 rpm Note: For final selection refer to individual performance curves 2
Construction Horizontal, single stage, end suction with vertical discharge, complying with the requirements of EN 733 (DIN 24255). Most models are suitable for 1600kPa (16 bar) pressure except for larger pumps that are rated for 1000kPa (10 bar). The pull back out design allows for the maintenance of the pump without disturbing the pipework connected to the casing, or the pump alignment. Flanges Pump flanges have raised faces and are to standards AS/NZS 4331.2, ISO 7005.2 16 bar. Gauge tappings are provided on suction and discharge flanges as standard. Impellers The shrouded impellers have front seals and, either back vanes or rear seals with balance holes to provide hydraulic balance. Impellers are dynamically balanced, are keyed to the shaft and are located axially between the sleeve and impeller nut. Zinc free bronze impellers are fitted as standard. Casing All pump casings are cast iron and radially split to permit removal of the rotating element. The vertical centre line discharge makes the casing self venting. Zinc free bronze wear rings are fitted as standard. Shaft Stainless steel shafts are standard and are ground to fit the impeller, sleeve, bearings and coupling. Bearings Grease Lubrication Standard Oil Lubrication for high speed models (EH) Max. Pump Temperature 95 o C The Bearing arrangement consists of two identical single row deep groove ball bearings which are grease lubricated through grease nipples located in each bearing cover. Shaft Seal The shaft sealing is carried out by means of mechanical seal with the option of packed gland. Mechanical Seal - A single mechanical seal, with a ceramic stationary face and carbon rotating face is fitted as standard. The standard seal elastomer is nitrile and is suitable for up to 95 o C temperature applications. The other seal components are AISI 304 stainless steel. Options: Balanced seal option M1 Cyclone separator option S1 Gland Packing - Fitted with removable lantern ring and square plaited packing. Packing is fitted over the sleeve to prevent shaft wear. Painting Prior to painting, the pump is thoroughly cleaned of scale, weld splatter and any other foreign material. The pump is then painted with a high quality industrial enamel paint. Accessories Drive The pump is only recommended for direct drive via a flexible spacer coupling. Spacer couplings enable the utilisation of the back pull out feature. Where belt drives are necessary a separate jack (intermediate) shaft with bearings to carry the belt loads may be required. All drive systems, where supplied by KSB Ajax, are appropriately protected by suitable guards. Baseplate Baseplates for electric drives are available in a variety of styles: Standard - Fixed and grouted directly to the foundation. Anti Vibration - Rigid baseplate on rubber mounts. - Rigid baseplate on spring mounts. - Rigid baseplate with inertia block base and spring mounts. The baseplate is manufactured or fabricated from either cold formed (pressed) steel plate or from rolled steel channel sections. Pump Selection For pump selection the hydraulic performance curves should be used. These curves are based on water at 15 o C and SG equal to 1.0. NPSH values are indicated on the performance curves. At least 0.5m should be added as a safety margin. To overcome variations between actual and design system requirements it is recommended that the driver power exceeds the absorbed pump shaft power. Absorbed Pump Shaft [kw] Up to 7.5 7.5-40 Above 40 Driver Power Reserve Approx. 20% Approx. 15% Approx. 10% 3
General Operating Parameters Packed Gland Mechanical Seal Standard Seal Option M1 Pressure Maximum operating pressure* 1600kPa 1400kPa 1400kPa Maximum hydrostatic test pressure 2100kPa 2100kPa 2400kPa Maximum suction pressure 1450rpm 600kPa 900kPa 1000kPa Maximum suction pressure 2900rpm 400kPa 700kPa 1000kPa Temperature Packed gland Mechanical Seal: Standard Mechanical Seal Balanced: Option M1-20 o C to 95 o C -20 o C to 95 o C -20 o C to 95 o C Speed Maximum Speed* *refer tabular listing on page 5. 3600 rpm Material Specifications Material Component Nearest Equivalent Standard Australian British American EN Cast Iron Casing Back Cover Bearing Housing ASTM A48 AS1830/T220 BS1452: GR220 Bearing Cover Class 30 JL 1030 Lantern Ring Wear Rings (Option) Zinc Free Impeller BS 1400-1973 Bronze AS1565-1985 ASTM Wear Rings CC480 K - GC Alloy C90250 CT1 C 90700 906D Bronze Lantern Ring Bush AS1565-C83600 BS1400-LG2 ASTM B584-C83600 - Stainless Steel Shaft Shaft Sleeve AS2837 GR.420 AS2837 GR.316 BS970:420/S37 BS970:316 AISI Type 420 AISI Type 316 X20CR13 X10CRN1MOT118/10 Pump Material Combinations Part Mechanical Seal Packed Gland Packed Gland Description Code 04 (A20C) Code 07 (AXOC) Code 09 (AXOJJ) Casing Cast Iron Cast Iron Stainless Steel Impeller Zinc Free Bronze Zinc Free Bronze Stainless Steel Wear Rings Zinc Free Bronze Zinc Free Bronze Stainless Steel Shaft Stainless Steel Stainless Steel 420 Stainless Steel Shaft Sleeve Not Fitted Stainless Steel Stainless Steel Spring Sleeve Stainless Steel Not Fitted Not Fitted Lantern Ring Not Fitted Cast Iron Stainless Steel Lantern Ring Bush Not Fitted Bronze Stainless Steel Gland Not Fitted Cast Iron Stainless Steel Seal Plate Cast Iron Not Fitted Not Fitted Mechanical Seal Materials Part Description Seat Ceramic Silicon Cabid Seal Face Carbon Carbon Seal O Ring Nitrile Nitrile Bellows Nitrile Nitrile Retainer Drive Band Spring Holder Spring Standard Stainless Steel AISI 304 High Pressure Option M1 Stainless Steel AISI 316 4
Pump Technical Data Pump Model Maximum Nominal Speed Direct Coupled Bearing Type Mass Moment of Inertia J Rotating Assy. Less Coupling [kg*m 2 ] Hydrostatic Test Pressure Maximum Maximum Working Pressure up to 120 C rpm/imp. dia Front Rear Bronze Impeller bar kpa PSI bar kpa PSI E32-13 3450/134 6305 6305 0.004 21 2100 304 16 1600 232 E32-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232 E32-20 3450/181 6305 6305 0.015 21 2100 304 16 1600 232 E32-26 3450/220 6305 6305 0.043 21 2100 304 16 1600 232 E40-13 3450/130 6305 6305 0.004 21 2100 304 16 1600 232 E40-16 3450/156 6305 6305 0.006 21 2100 304 16 1600 232 E40-20 3450/186 6305 6305 0.019 21 2100 304 16 1600 232 E40-26 3450/225 6305 6305 0.048 21 2100 304 16 1600 232 E40-32 2300/329 6307 6307 0.105 21 2100 304 16 1600 232 EH40-32 2900/320 3307 3307 0.105 21 2100 304 16 1600 232 E50-13 3450/132 6305 6305 0.005 21 2100 304 16 1600 232 E50-16 3450/159 6305 6305 0.008 21 2100 304 16 1600 232 E50-20 3450/182 6305 6305 0.019 21 2100 304 16 1600 232 E50-26 3450/227 6305 6305 0.05 21 2100 304 16 1600 232 E50-32 2300/328 6307 6307 0.111 21 2100 304 16 1600 232 EH50-32 2900/314 3307 3307 0.111 21 2100 304 16 1600 232 E65-13 3450/159 6305 6305 0.006 21 2100 304 16 1600 232 E65-16 3450/159 6305 6305 0.009 21 2100 304 16 1600 232 E65-20 3450/184 6305 6305 0.019 21 2100 304 16 1600 232 E65-26 3450/224 6307 6307 0.052 21 2100 304 16 1600 232 E65-32 2400/329 6307 6307 0.127 21 2100 304 16 1600 232 EH65-32 2900/316 3307 3307 0.127 21 2100 304 16 1600 232 E80-16 3450/160 6305 6305 0.013 21 2100 304 16 1600 232 E80-20 3450/191 6307 6307 0.024 21 2100 304 16 1600 232 E80-26 3450/230 6307 6307 0.05 21 2100 304 16 1600 232 E80-32 1800/329 6307 6307 0.107 21 2100 304 16 1600 232 EH80-32 2900/318 3307 3307 0.107 21 2100 304 16 1600 232 E80-40 1800/409 6309 6309 0.392 17 1700 246 13 1300 188 E100-16 2900/174 6307 6307 0.02 21 2100 304 16 1600 232 E100-20 3450/193 6307 6307 0.03 21 2100 304 16 1600 232 E100-26 3450/228 6307 6307 0.068 21 2100 304 16 1600 232 E100-32 1800/329 6307 6307 0.156 21 2100 304 16 1600 232 E100-40 1800/409 6309 6309 0.358 17 1700 246 13 1300 188 E125-20 2900/214 6307 6307 0.069 21 2100 304 16 1600 232 E125-26 1800/264 6307 6307 0.076 21 2100 304 16 1600 232 E125-32 1800/329 6309 6309 0.165 21 2100 304 16 1600 232 E125-40 1800/409 6309 6309 0.377 17 1700 246 13 1300 188 E150-20 1800/220 6307 6307 0.078 15 1500 217 11 1100 159 E150-26 1800/264 6309 6309 0.158 15 1500 217 11 1100 159 E150-32 1800/329 6309 6309 0.182 15 1500 217 11 1100 159 E150-40 1800/409 6309 6309 0.4 15 1500 217 11 1100 159 E200-26 1800/264 6309 6309 0.3 15 1500 217 11 1100 159 E200-32 1800/329 6311 6311 0.217 15 1500 217 11 1100 159 E200-40 1800/409 6311 6311 0.441 15 1500 217 11 1100 159 E250-32 1800/329 6311 6311 0.221 15 1500 217 11 1100 159 E250-40 1800/409 6311 6311 0.451 15 1500 217 11 1100 159 5
Pump Technical Data Impeller Data B.P.O Pump Model Seal Ring Bearing Expeller Vane Diametrical Diameter Vane No. of Eye Front Seal Back Seal Element Clearance [mm] Width Vanes Diameter Diameter Diameter Weight [kg] [mm] [mm] [mm] [mm] [mm] No. of Height [mm] Dia. [mm] Vanes [mm] (Pump Less Max. Min. Max. Min. Casing) E32-13* 0.4 0.3 139 100 7 6 61 70 - - - - 20 E32-16 0.4 0.3 174 125 6 6 62 70-120 6 3 25 E32-20 0.4 0.3 214 165 6 4 68 80-140 8 3 32 E32-26 0.4 0.3 264 205 5 6 70 80-200 6 4 43 E40-13* 0.4 0.3 139 100 10 6 71 80 - - - - 20 E40-16 0.4 0.3 175 130 7.5 6 68 80-114 8 3.5 25 E40-20 0.4 0.3 214 165 7 6 69 80-153 8 3 33 E40-26 0.4 0.3 264 205 6 6 84 95-168 8 5 44 E40-32 0.4 0.3 329 255 6 6 77 95 95 - - - 59 EH40-32 0.4 0.3 320 255 6 6 77 95 95 - - - 59 E50-13 0.4 0.3 139 120 16 6 88 95-126 6 3 22 E50-16 0.4 0.3 174 135 13 6 85 95-164 6 2.5 26 E50-20 0.4 0.3 214 165 10 6 86 95-154 8 3 33 E50-26 0.4 0.3 264 205 8 7 94 115-189 8 5.5 45 E50-32 0.4 0.3 328 255 7 6 102 115 115 - - - 56 EH50-32 0.4 0.3 314 255 7 6 102 115 115 - - - 56 E65-13 0.4 0.3 139 130 23 7 100 115-139 6 4.5 24 E65-16 0.4 0.3 174 125 19 6 102 115-139 6 6 28 E65-20 0.4 0.3 214 165 16 6 107 115-180 8 4 35 E65-26 0.4 0.3 264 205 13 6 108 115-228 8 2 66 E65-32 0.5 0.4 329 255 10 7 114 130 125 - - - 73 EH65-32 0.5 0.4 316 255 10 7 114 130 125 - - - 73 E80-16 0.5 0.4 174 145 25 7 118 130-151 8 5 31 E80-20 0.5 0.4 214 165 22 6 121 130-186 8 4 46 E80-26 0.5 0.4 264 205 15 7 120 130-247 8 4 62 E80-32 0.5 0.4 329 255 13 6 125 140 135 - - - 74 EH80-32 0.5 0.4 318 255 13 6 125 140 135 - - - 74 E80-40 0.5 0.4 409 320 11 7 128 140 160 - - - 107 E100-16 0.5 0.4 174 165 32 7 148 160-164 9 4.5 20 E100-20 0.5 0.4 214 175 27 7 142 160-208 9 4 50 E100-26 0.5 0.4 264 205 23 7 145 160-253 10 5.5 56 E100-32 0.5 0.4 329 255 18 7 144 160 155 - - - 87 E100-40 0.5 0.4 409 320 15 6 147 160 160 - - - 120 E125-20 0.5 0.4 214 190 34 7 167 180-205 12 2 62 E125-26 0.5 0.4 264 205 32 6 167 180-236 12 3 67 E125-32 0.5 0.4 329 255 23 6 167 180 180 - - - 97 E125-40 0.5 0.4 409 320 20 7 166 180 180 - - - 122 E150-20 0.5 0.4 220 200 57 6 170 185 185 - - - 88 E150-26 0.5 0.4 264 210 39 7 185 200 200 - - - 93 E150-32 0.5 0.4 329 255 31 6 183 200 200 - - - 102 E150-40 0.5 0.4 409 320 26 7 188 200 200 - - - 125 E200-26 0.5 0.4 264 250 68 6 220 235 200 - - - 86 E200-32 0.5 0.4 329 285 50 6 232.5 250 250 - - - 153 E200-40 0.5 0.4 409 335 37.5 7 222 235 235 - - - 180 E250-32 0.5 0.4 329 285 72 6 242 260 260 - - - 190 E250-40 0.5 0.4 409 335 52 6 236 260 260 - - - 237 * no Expeller Vanes 6
Parts List and Material Identification Packed Gland Arrangement Pump Model: E40-32, E50-32, E65-32, E80-32, E80-40, E100-32, E100-40, E125-32, E125-40, E150-20, E150-26, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 Pump Model: E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20, E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16, E65-20, E65-26, E80-16, E80-20, E80-26, E100-16, E100-20, E100-26, E125-20, E125-26 Pump Models with clamped back cover: E32-13, E32-16, E40-13, E40-16, E50-13, E50-16, E65-13, E65-16, E80-16, E80-20, E100-16, E100-20, E125-20, E150-26, E200-26 Pump Models with bolted back cover: E32-20, E32-26, E40-20, E40-26, E40-32, E50-20, E50-26, E50-32, E65-20, E65-26, E65-32, E80-26, E80-32, E80-40, E100-26, E100-32, E100-40, E125-26, E125-32, E125-40, E150-20, E150-32, E150-40, E200-32, E200-40, E250-32, E250-40 * no Expeller Vanes ITEM DESCRIPTION MATERIAL ITEM DESCRIPTION MATERIAL 1A Casing Cast Iron 40.7 Gasket, Flange Plug Bonded Fibre 2A Impeller Zinc Free Bronze 42.1 Wear Ring, Casing Zinc Free Bronze 3A Backcover Cast Iron 42.2 Wear Ring, Backcover Zinc Free Bronze 10 Bearing Housing Cast Iron 43 Seal, Bearing Cover Felt* 11.1/.2 Bearing Cover Cast Iron 73 Support Foot Steel 20 Shaft Stainless Steel 82.1 Plug, Casing Drain Malleable Iron 21 Impeller Nut Bronze 82.2 Plug, Flange Malleable Iron 25 Slinger Rubber 85 Grease Nipple Steel 28.1 Key, Impeller Key Steel 90.1 Stud, Casing Steel 28.2 Key, Coupling Key Steel 90.2 Stud, Backcover Steel 29 Bearing Steel 90.3 Stud, Gland Steel 30 Gland Cast Iron 92 Setscrew, Bearing Cover Steel 31 Lantern Ring Bush Bronze 93 Setscrew, Support Foot Steel 31A Lantern Ring Cast Iron 94.1 Nut, Casing Stud Steel 32 Shaft Sleeve Stainless Steel 94.2 Nut, Backcover Stud Steel 34 Gland Packing Graphited Fibre 94.3 Nut, Gland Stud Steel 40** Gasket, Casing Bonded Fibre/NBR 97 Washer, Impeller Nut Brass 40.6 Gasket, Drain Plug Bonded Fibre *Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 **From 1997 O Ring used instead of gasket. 7
Parts List and Material Identification Mechanical Seal Arrangement Pump Model: E40-32, E50-32, E65-32, E80-32, E80-40, E100-32, E100-40, E125-32, E125-40, E150-20, E150-26, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 Pump Model: E32-13*, E32-16, E32-20, E32-26, E40-13*, E40-16, E40-20, E40-26, E50-13, E50-16, E50-20, E50-26, E65-13, E65-16, E65-20, E65-26, E80-16, E80-20, E80-26, E100-16, E100-20, E100-26, E125-20, E125-26 Pump Models with clamped back cover: E32-13, E32-16, E40-13, E40-16, E50-13, E50-16, E65-13, E65-16, E80-16, E80-20, E100-16, E100-20, E125-20, E150-26, E200-26 Pump Models with bolted back cover: E32-20, E32-26, E40-20, E40-26, E40-32, E50-20, E50-26, E50-32, E65-20, E65-26, E65-32, E80-26, E80-32, E80-40, E100-26, E100-32, E100-40, E125-26, E125-32, E125-40, E150-20, E150-32, E150-40, E200-32, E200-40, E250-32, E250-40 * no Expeller Vanes ITEM DESCRIPTION MATERIAL ITEM DESCRIPTION MATERIAL 1A Casing Cast Iron 41 O Ring Seal Plate Nitrile 2A Impeller Zinc Free Bronze 42.1 Wear Ring, Casing Zinc Free Bronze 3A Backcover Cast Iron 42.2 Wear Ring, Backcover Zinc Free Bronze 10 Bearing Housing Cast Iron 43 Seal, Bearing Cover Felt* 11.1/.2 Bearing Cover Cast Iron 73 Support Foot Steel 20 Shaft Stainless Steel 82.1 Plug, Casing Drain Malleable Iron 21 Impeller Nut Bronze 82.2 Plug, Flange Malleable Iron 25 Slinger Rubber 85 Grease Nipple Steel 28.1 Key, Impeller Key Steel 90.1 Stud, Casing Steel 28.2 Key, Coupling Key Steel 90.2 Stud, Backcover Steel 29 Bearing Steel 90.3 Stud, Gland Steel 35 Mechanical Seal Carbon/Ceramic 92 Setscrew, Bearing Cover Steel 36 Spring Sleeve Stainless Steel 93 Setscrew, Support Foot Steel 37 Seal Plate Cast Iron 94.1 Nut, Casing Stud Steel 40** Gasket, Casing Bonded Fibre/NBR 94.2 Nut, Backcover Stud Steel 40.6 Gasket, Drain Plug Bonded Fibre 94.3 Nut, Gland Stud Steel 40.7 Gasket, Flange Plug Bonded Fibre 97 Washer, Impeller Nut Brass *Note: Lip Seals fitted to pump models E80-40, E100-40, E125-32, E125-40, E150-32, E150-40, E200-26, E200-32, E200-40, E250-32, E250-40 **From 1997 O Ring used instead of gasket. 8
ROTATION Dimensions FLANGES DRILLED TO AS/NZS 4331.2 (ISO 7005.2-16bar) DISCHARGE SUCTION END ELEVATION SIDE ELEVATION PUMP SHAFT SUCT. DISCH. PUMP FOOT SPACER SHAFT COUPLING NET SIZE MODULE END KEY WEIGHT a f h 1 h 2 b m 1 m 2 n 1 n 2 n 3 h 3 s 1 s 2 w p y d l [kg] E32-13 25 50 32 80 360 112 140 50 100 70 190 140 100 14 14 14 267 80 100 24 50 8x7 27 E32-16 25 50 32 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 35 E32-20 25 50 32 80 360 160 180 50 100 70 240 190 110 14 14 14 267 80 100 24 50 8x7 41 E32-26 25 50 32 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 59 E40-13 25 65 40 80 360 112 140 50 100 70 210 160 100 14 14 14 267 80 100 24 50 8x7 30 E40-16 25 65 40 80 360 132 160 50 100 70 240 190 100 14 14 14 267 80 100 24 50 8x7 36 E40-20 25 65 40 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 44 E40-26 25 65 40 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 61 E40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96 EH40-32 35 65 40 125 470 200 225 65 130 95 345 280 110 14 14 14 342 125 140 32 80 10x8 96 E50-13 25 65 50 100 360 132 160 50 100 70 240 190 100 14 14 14 267 100 100 24 50 8x7 34 E50-16 25 65 50 100 360 160 180 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 38 E50-20 25 65 50 100 360 160 200 50 100 70 265 212 110 14 14 14 267 100 100 24 50 8x7 46 E50-26 25 65 50 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 63 E50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101 EH50-32 35 65 50 125 470 225 280 65 125 95 345 280 110 16 14 14 342 124 140 32 80 10x8 101 E65-13 25 80 65 100 360 160 180 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 39 E65-16 25 80 65 100 360 160 200 65 125 95 280 212 110 14 14 14 267 100 100 24 50 8x7 43 E65-20 25 80 65 100 360 180 225 65 125 95 320 250 110 14 14 14 267 100 100 24 50 8x7 70 E65-26 35 80 65 100 470 200 250 80 160 120 360 280 110 16 18 14 342 100 140 32 80 10x8 81 E65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110 EH65-32 35 80 65 125 470 225 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 110 E80-16 25 100 80 125 360 180 225 65 125 95 320 250 110 14 14 14 267 125 100 24 50 8x7 54 E80-20 35 100 80 125 470 180 250 65 125 95 345 280 110 14 14 14 342 125 140 32 80 10x8 70 E80-26 35 100 80 125 470 200 280 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 91 E80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120 EH80-32 35 100 80 125 470 250 315 80 160 120 400 315 110 16 18 14 342 125 140 32 80 10x8 120 E80-40 45 100 80 125 532 280 365 85 160 120 440 340 110 19 18 14 368 132 140 42 110 12x8 161 E100-16 35 125 100 125 470 200 280 30 160 120 340 260 110 16 18 14 342 125 140 32 80 10x8 71 E100-20 35 125 100 125 470 200 280 80 160 120 360 280 110 16 18 14 342 125 140 32 80 10x8 85 E100-26 35 125 100 140 470 225 280 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106 E100-32 35 125 100 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 134 E100-40 45 125 100 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 174 E125-20 35 150 125 140 470 250 315 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 106 E125-26 35 150 125 140 470 250 355 80 160 120 400 315 110 16 18 14 342 140 140 32 80 10x8 115 E125-32 45 150 125 140 530 280 355 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 163 E125-40 45 150 125 140 530 315 400 100 200 150 500 400 110 18 23 14 370 140 140 42 110 12x8 181 E150-20 35G 200 150 160 495 280 400 100 200 150 550 450 110 20 23 14 367 160 140 32 80 10x8 156 E150-26 45 200 150 160 530 250 355 100 200 150 450 350 110 18 23 14 370 160 140 42 110 10x8 148 E150-32 45 200 150 160 530 280 400 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 170 E150-40 45 200 150 160 530 315 450 100 200 150 550 450 110 18 23 14 370 160 140 42 110 12x8 209 E200-26 45D 250 200 180 553 315 450 100 200 150 550 450 110 20 28 14 393 180 180 42 110 12x8 206 E200-32 55 250 200 180 670 315 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 251 E200-40 55 250 200 180 670 335 480 120 220 170 600 480 110 20 28 14 504 180 180 48 110 14x9 295 E250-32 55 300 250 220 691 355 520 150 250 200 660 510 110 22 28 14 525 220 180 48 110 14x9 311 E250-40 55 300 250 220 682 400 560 150 250 200 660 510 110 22 28 14 516 220 180 48 110 14x9 390 Dimensions shown in mm 9
Flange Data Branch Flange Raised Face Drilling* Size D b d 1 f N0. d 2 k Bolting 32 140 18 78 2 4 18 100 M16 40 150 18 88 3 4 18 110 M16 50 165 20 102 3 4 18 125 M16 65 185 20 122 3 4 18 145 M16 80 200 22 138 3 8 18 160 M16 100 220 24 158 3 8 18 180 M16 125 250 26 188 3 8 18 210 M16 150 285 26 212 3 8 22 240 M20 200 340 32 268 3 12 22 295 M20 250 405 32 320 3 12 26 355 M24 300 460 32 378 4 12 26 410 M24 Flange dimensions and drilling according to AS/NZS 4331.2, ISO 7005.2-16 bar (BS4504-1969 Table 16/11, DIN 2533 PN16) Dimensions shown in mm *Holes - Equally spaced straddling pump centreline Shaft Dimensions KEY LENGTH Service Connections KEY WIDTH KEY HEIGHT SEAT DEPTH Shaft Diameter D Key Key Key Seat Module Nom Tol Length Height Width Depth 25 35 45 55 24 32 42 48-0.004 +0.009-0.002 +0.018-0.002 +0.018-0.002 +0.018 32 40 50 80 7 8 8 9 8 10 12 14 20 27 37 42.5 Key dimensions are in nominal and expressed in mm PUMP A B* D S PUMP A B* D S MODEL CASING HOUSING GAUGE GAUGE MODEL CASING HOUSING GAUGE GAUGE DRAIN DRAIN TAPPING TAPPING DRAIN DRAIN TAPPING TAPPING E32-13 1/4 3/8 1/4 1/4 E80-26 3/8 3/8 1/4 1/4 E32-16 1/4 3/8 1/4 1/4 E80-32 3/8 3/8 3/8 3/8 E32-20 1/4 3/8 1/4 1/4 EH80-32 3/8 3/8 3/8 3/8 E32-26 3/8 3/8 1/4 1/4 E80-40 3/8 3/8 1/4 3/8 E40-13 1/4 3/8 1/4 1/4 E100-16 3/8 3/8 1/4 3/8 E40-16 1/4 3/8 1/4 1/4 E100-20 3/8 3/8 1/4 3/8 E40-20 1/4 3/8 1/4 1/4 E100-26 3/8 3/8 3/8 3/8 E40-26 3/8 3/8 1/4 1/4 E100-32 3/8 3/8 3/8 3/8 E40-32 3/8 3/8 1/4 1/4 E100-40 3/8 3/8 1/4 3/8 EH40-32 3/8 3/8 1/4 1/4 E125-20 3/8 3/8 3/8 3/8 E50-13 1/4 3/8 1/4 1/4 E125-26 3/8 3/8 3/8 3/8 E50-16 3/8 3/8 1/4 1/4 E125-32 3/8 3/8 3/8 3/8 E50-20 1/4 3/8 1/4 1/4 E125-40 3/8 3/8 3/8 3/8 E50-26 3/8 3/8 1/4 1/4 E150-20 3/8 3/8 1/4 3/8 E50-32 3/8 3/8 1/4 1/4 E150-26 3/8 3/8 3/8 3/8 EH50-32 3/8 3/8 1/4 1/4 E150-32 3/8 3/8 3/8 3/8 E65-13 1/4 3/8 1/4 1/4 E150-40 3/8 3/8 3/8 3/8 E65-16 3/8 3/8 1/4 1/4 E200-26 3/8 1/2 3/8 3/8 E65-20 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8 3/8 E65-26 3/8 3/8 1/4 1/4 E200-32 3/8 3/8 3/8 3/8 E65-32 3/8 3/8 1/4 1/4 E200-40 3/8 3/8 3/8 3/8 EH65-32 3/8 3/8 1/4 1/4 E250-32 3/8 3/8 3/8 3/8 E80-16 3/8 3/8 1/4 1/4 E250-40 3/8 3/8 3/8 3/8 E80-20 3/8 3/8 1/4 1/4 Dimensions shown in inch ROTATION END ELEVATION DISCHARGE SUCTION SIDE ELEVATION *Left side view from suction 10
Nominal Stuffing Box Dimensions MODULE 25 & 35 From end of stuffing box. NOTE: Only some models have combination lantern ring-register bush, check assembly drawing. MODULE 45 & 55 Module L L 1 L 2 d d 1 d 2 k f g Packing Size No. rings 25 44 30 56 48 32 24 85 M8 35 8 Sq 3 35 53* 40* 63** 60 40 32 100 M10 40 10 Sq 3* 45 63 46 78 75 54 44 110 M12 50 10 Sq 4 55 80 62 62 90 65 53 130 M12 55 13Sq 4 *: models E40-32, E50-32, E65-32, E80-32, E100-32, E100-32, E125-26 L=63, L 1 =50, No. Rings=4 Dimensions shown in mm **: model E150-20 L 2 =83 Mechanical Seal, A20 - Conversion Kits The kit is suitable to convert standard packed gland pumps. The kit comprises of mechanical seal, spring sleeve, seal plate, O ring seal and nameplate. Pump Size Module Conversion Kit No. E32-13/16/20/26 E40-13/16/20/26 E50-13/16/20/26 25 213591 E65-13/16/20 E80-16 E40-32, EH40-32 E50-32, EH50-32 E65-26/32, EH 65-32 E80-20/26/32, EH80-32 E100-16/20/26/32 E125-20/26 E150-20 35 35G 213592 213592G E80-40 E100-40 E125-32/40 E150-26/32/40 45 213593 E200-26 45D E200-32 E200-40 E250-32 55 E250-40 213593D 213594 Parts included in kit Mechanical Seal 213524 Spring Sleeve Seal Plate O ring Nameplate Mechanical Seal Spring Sleeve Seal Plate O ring Nameplate Mechanical Seal Spring Sleeve Seal Plate O ring Nameplate 36-25-HF 21371HA BS-225-GM 218003 213532 21361HF (35) 36-35G-HF (35G) 21372HA BS-229-GM 218003 Mechanical Seal 213544 Spring Sleeve 36-45-HF (45) 36-45D-HF (45D) Seal Plate O ring 21373HA BS-233-GM Nameplate 218003 213553 36-55-HF 21374HA BS-238-GM 218003 11
Type Series Booklet Elite KSB Australia Pty Ltd ABN: 29 006 414 642 Victorian Head Office New South Wales Queensland South Australia Western Australia New Zealand 27 Indwe St, Unit 1, 28 Skinner Ave, 53 Jijaws St, Unit 4, 348 Richmond Rd, Unit 2, 86 Catalano Circuit, Unit 2, 5 Civil Place, Tottenham, 3012 Riverwood, 2210 Sumner Park, 4074 Netley, 5037 Canning Vale, 6155 Albany, Auckland 1331 Tel: +61 (03) 9314 0611 Tel: +61 (02) 9584 2099 Tel: +61 (07) 3725 8200 Tel: +61 (08) 8234 0066 Tel: +61 (08) 9455 7900 Tel: +64 (09) 476 4047 Fax: +61 (03) 9314 7435 Fax: +61 (02) 9584 2111 Fax: +61 (07) 3725 8299 Fax: +61 (08) 8443 5411 Fax: +61 (08) 9455 7800 Fax: +64 (09) 476 4048 ksbvicsales@ksbajax.com.au ksbnswsales@ksbajax.com.au ksbqldsales@ksbajax.com.au ksbsasales@ksbajax.com.au ksbwasales@ksbajax.com.au pumps@ksbajax.co.nz WEBSITE: www.ksbajax.com.au 24 HOUR EMERGENCY SERVICE LINE: 1300 301 356 Due to our policy of constant research and development, product specification may change without notice Publication 2007 02/14 1/2K AGP