QSERIES. The Leader in Actuator Technology QUARTER-TURN PNEUMATIC & FLUID POWER ACTUATOR PRODUCT BULLETIN

QUARTER-TURN PNEUMATIC & FLUID POWER ACTUATOR PRODUCT BULLETIN Output Torques to 21,000 in-lb (2373 Nm) Temperatures from -76ºF to 450ºF (-60ºC to 232ºC) Ductile Iron or Stainless Steel Construction Double-Acting and Spring-Return Models HIGH CYCLE LIFE, HIGH SPEED, HIGH RELIABILITY The Leader in Actuator Technology

QTRCO, INC. PRODUCT BULLETIN Q SERIES PRODUCT BULLETIN REVISION LOG Date Modifications August 2015 Complete update of design & data March 2016 Updates to materials of construction October 2016 Incorporate Hydraulic Operation November 2016 Environmental Ingress Protection DCN00650(11) 2 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES TABLE OF CONTENTS OPERATION AND PIPING P5 DIMENSIONS AND TECHNICAL DATA P6 PRESSURE EQUIPMENT DIRECTIVE CATEGORY CLASSIFICATION P 12 TORQUE DATA P 13 PARTS DIAGRAM & MATERIALS OF CONSTRUCTION P 18 ENGINEERING STRING P 19 www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 3

QTRCO, INC. PRODUCT BULLETIN OPERATION AND PIPING Q2 series actuators may be operated with instrument air, hydraulic fluid, water, or other power gases and fluids. Always ensure that the materials of construction are compatible with the application and that the pressure does not exceed the maximum allowable. Environmental Ingress Protection (Submerged Service) Q2-Series actuators are capable of achieving IP67 and IP68 ratings for continuous immersion up to a depth of 10 meters. Double acting versions may achieve the rating by tubing in the normal manner. For spring return actuators, the IP67 and IP68 rating may be achieved by one of three methods: 1. The actuator breather port may be fitted with a filter or strainer, allowing fluid to enter the actuator body. This method may only be used if the submersion fluid is compatible with the actuator materials of construction and lubricants. Because the fluid will not adversely affect actuator operation, IP68 requirements will still be met. This method may reduce stroke speed depending on the flow capacity of the filter. 2. The actuator breather port may be plugged using appropriate thread sealant. This method may slightly reduce air torque output due to compression of the air trapped in the actuator body. 3. The actuator breather port may be piped to a non-submerged location and fitted with a filter or strainer device. For the highest level of safety, QTRCO recommends method 3, piping the breather port to a non-submerged location. All QTRCO actuators are shipped in the Fail-Close or Left-Hand orientation unless ordered as Fail-Open or Right-Hand. The mode of operation may be reversed in the field simply by turning the actuator top-side down. 1. Fail-Close (Left-Hand): pressure on the end cap port(s) pushes the piston(s) inward resulting in counterclockwise rotation. Exhaustion of pressure allows springs to push outward on the piston and cause clockwise rotation. 2. Fail-Open (Right-Hand): pressure on the end cap port(s) pushes the piston(s) inward resulting in clockwise rotation. Exhaustion of pressure allows springs push outward on the piston and cause counterclockwise rotation. 3. Double Acting (Left-Hand): pressure on the end cap port(s) pushes the piston(s) inward and causes counterclockwise rotation. Pressure on the body port pushes outward on the piston(s) and cause clockwise rotation. 4. Double Acting (Right-Hand): pressure on the end cap port(s) pushes the piston(s) inward and causes clockwise rotation. Pressure on the body port pushes outward on the piston(s) and cause counterclockwise rotation. 4 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES PIPING GUIDELINES: 1. Dual cylinder models (205, 210, 214), both endcap pressure ports (P1 and P2) must be utilized for proper operation. 2. P1 and P2 are typically connected together and powered by a single pathway. 3. Single Cylinder models (203, 204, 207, 212), port 2 (P2) does not exist. 205DA, 210DA, 214DA 4. Spring Return (SR and SD) models port 3 (P3) is a breather port. 5. P3 is a pressure port for Double Acting models. 6. P3 is a breather port for single cylinder SR models. 203DA, 204DA, 207DA, 212DA P3 P1 P3 P1 P2 P3 P1 P3 P1 P2 205SR, 210SR, 214SR 203SR, 204SR, 207SR, 212SR P2 P3 P1 P3 P1 P3 P2 P1 P3 P1 www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 5

QTRCO, INC. PRODUCT BULLETIN Dimensions and Technical Data SINGLE CYLINDER MODELS (203, 204, 207, 212) 6 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES Dimensions and Technical Data DUAL CYLINDER MODELS (205, 210, 214) www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 7

QTRCO, INC. PRODUCT BULLETIN ENVELOPE DIMENSIONS Dimensions and Technical Data (Imperial, Inches) 203 204 205 207 210 212 214 DA SR DA SR DA SD SR DA SR DA SD SR DA SR DA SD SR Width Total A1 4.19 4.75 5.75 6.81 8.62 10.06 12.24 Width Side 1 A2 2.31 2.88 2.88 4.31 4.31 6.12 6.12 Width Side 2 A3 1.88 1.88 2.88 2.50 4.31 3.95 6.12 Width Cylinder A4 3.38 4.50 4.50 6.50 6.50 8.75 8.75 Height Cylinder A5 3.38 4.50 4.50 6.50 6.50 8.75 8.75 Length Total B1 5.71 6.67 7.16 9.01 9.10 10.95 12.80 10.89 15.19 14.10 18.40 22.70 15.95 20.68 20.31 25.04 29.77 Length Side 1 B2 3.77 4.73 4.55 6.40 4.55 6.40 7.05 11.35 7.05 11.35 10.16 14.89 10.16 14.89 Length Side 2 B3 1.94 2.61 4.55 6.40 3.85 7.05 11.35 5.80 10.16 14.89 Flange Distance C 0.82 1.43 1.43 2.15 2.15 3.93 3.93 Flange Depth* D 0.00 0.00 0.00 0.54 0.54 0.38 0.38 Stop Extension E 0.29 0.29 0.29 0.68 0.68 0.59 0.59 Maint Clearance F1 5.71 7.63 6.43 10.13 6.43 10.13 10.25 18.83 10.25 18.83 14.50 23.85 14.50 23.85 Maint Clearance F2 6.43 10.13 10.25 18.83 14.50 23.85 *On 203, 204, and 205 models, the cylinder flange is flush with the mounting surface ISO BOLT PATTERN F05 F05/F07 F05/F07 F10 F10 F16 F16 BCD 1 H1 1.969 1.969 1.969 4.016 4.016 6.496 6.496 Thread 1 H2 M6-1 M6-1 M6-1 M10-1.5 M10-1.5 M20-2.5 M20-2.5 BCD 2 J1 2.756 2.756 RECT X J2 1.52 1.52 2.00 2.00 RECT Y J3 4.02 4.02 6.50 6.50 Thread 2 J4 M8-1.25 M8-1.25 Thread depth 0.63 0.63 0.63 0.88 0.88 1.00 1.00 Identical mounting patterns on both sides of actuator for all sizes. Size 203 has a single ISO pattern. Sizes 204/205 have two ISO patterns. Sizes 207/210/212/214 have an ISO pattern and a rectangular pattern. NAMUR PATTERN 1 1 1 1 1 3 3 Length N1 3.15 3.15 3.15 3.15 3.15 5.12 5.12 Width N2 1.18 1.18 1.18 1.18 1.18 1.18 1.18 Height N3 0.79 0.79 0.79 0.79 0.79 1.18 1.18 Slot Width N4 0.157 0.157 0.157 0.157 0.157 0.157 0.157 Slot Depth N5 0.197 0.197 0.197 0.197 0.197 0.197 0.197 Thread 2 N6 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 Thread Depth 0.375 0.375 0.375 0.375 0.375 0.375 0.375 The NAMUR slotted drive can be moved to the opposite side for field reversibility. 203, 204, and 205 sizes include a removable NAMUR adapter plate that can be moved to the opposite side. The NAMUR adapter plate covers the accessory side mounting patterns when installed. 8 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES DOUBLE SQUARE FEMALE DRIVE Dimensions and Technical Data (Imperial, Inches) 203 204 205 207 210 212 214 DA SR DA SR DA SD SR DA SR DA SD SR DA SR DA SD SR F07 F07 F07 F14 F14 F25 F25 Square S1 0.669 0.669 0.669 1.417 1.417 2.165 2.165 Square Depth S2 1.30 1.30 1.30 1.00 1.00 1.80 1.80 Outer Diameter S3 0.870 0.870 0.870 1.890 1.890 2.870 2.870 Inner Diameter S4 0.750 0.750 0.750 1.600 1.600 2.430 2.430 Identical double square female drive on both sides of the actuator for all sizes AIR/FLUID VOLUME cubic inches (cuin) Body 14-25 - 44 - - 111-166 - - 302-469 - - End Caps 9 15 30 59 117 163 326 PORT SIZE P1, P2, P3 Normal 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT Max 1/2" NPT 1/2" NPT 1/2" NPT 3/4" NPT 3/4" NPT 1" NPT 1" NPT STROKE TIME seconds Normal 0.25 0.5 0.5 1 1 3 3 Min 0.01 0.015 0.015 0.03 0.03 0.05 0.05 *Stroke time varies with supply pressure, temperature, spring rate, travel adjustment, working medium, piping, accessory flow rates, and valve torque. Values shown with no valve resistance. CENTER OF GRAVITY COGx 0.41 0.45 0.43 0.47 0.00 0.89 0.00 0.88 0.88 0.00 0.00 0.00 0.94 1.12 0.01 0.03 0.01 COGy 0.11 0.10 0.04 0.04 0.04 0.04 0.03 0.01 0.01 0.00 0.00 0.00 0.01 0.00 0.01 0.00 0.00 COGz* 1.1/1.2 1.5/1.7 1.1/1.3 1.8/2.1 0.00 0.5/0.8 0.00 1.9/2.3 4.1/4.4 0.00 1.6/2.2 0.00 2.2/2.8 4.5/4.9 0.00 1.7/2 0.00 *CoGz is variable for some models and changes with actuator stroke. Values are shown as min/max. WEIGHT pounds (lb) MAX PRESSURE psig QS - Stainless 6 7 14 17 22 25 29 33 51 52 70 88 87 113 126 151 177 QD - Ductile 5 6 12 14 19 21 24 29 45 44 60 78 78 102 111 133 155 150 150 150 150 150 150 150 TEMPERATURE LIMITS LOW STANDARD HIGH Environmental temperature requirements may limit the use of certain trim materials. Temperature ranges may be extended -60ºF to 185ºF -20ºF to 185ºF -20ºF to 400ºF with proper insulation. Ductile iron units may be used in low temperature (less than -20ºF), but stroke speed should be limited www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 9

QTRCO, INC. PRODUCT BULLETIN ENVELOPE DIMENSIONS Dimensions and Technical Data (Metric, Millimeters) 203 204 205 207 210 212 214 DA SR DA SR DA SD SR DA SR DA SD SR DA SR DA SD SR Width Total A1 106 121 146 173 219 256 311 Width Side 1 A2 59 73 73 109 109 155 155 Width Side 2 A3 48 48 73 64 109 100 155 Width Cylinder A4 86 114 114 165 165 222 222 Height Cylinder A5 86 114 114 165 165 222 222 Length Total B1 145 169 182 229 231 278 325 277 386 358 467 577 405 525 516 636 756 Length Side 1 B2 96 120 116 163 116 163 179 288 179 288 258 378 258 378 Length Side 2 B3 49 66 116 163 98 179 288 147 258 378 Flange Distance C 21 36 36 55 55 100 100 Flange Depth* D 0 0 0 14 14 10 10 Stop Extension E 7 7 7 17 17 15 15 Maint Clearance F1 145 194 163 257 163 257 260 478 260 478 368 606 368 606 Maint Clearance F2 - - 163 257-260 478-368 606 *On 203, 204, and 205 models, the cylinder flange is flush with the mounting surface ISO BOLT PATTERN F05 F05/F07 F05/F07 F10 F10 F16 F16 BCD 1 H1 50.0 50.0 50.0 102.0 102.0 165.0 165.0 Thread 1 H2 M6-1 M6-1 M6-1 M10-1.5 M10-1.5 M20-2.5 M20-2.5 BCD 2 J1 70.0 70.0 RECT X J2 38.6 38.6 50.8 50.8 RECT Y J3 102.0 102.0 165.1 165.1 Thread 2 J4 M8-1.25 M8-1.25 Thread depth 15.9 15.9 15.9 22.2 22.2 25.4 25.4 Identical mounting patterns on both sides of actuator for all sizes. Size 203 has a single ISO pattern. Sizes 204/205 have two ISO patterns. Sizes 207/210/212/214 have an ISO pattern and a rectangular pattern. NAMUR PATTERN 1 1 1 1 1 3 3 Length N1 80 80 80 80 80 130 130 Width N2 30 30 30 30 30 30 30 Height N3 20 20 20 20 20 30 30 Slot Width N4 4 4 4 4 4 4 4 Slot Depth N5 5 5 5 5 5 5 5 Thread 2 N6 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 M5-0.8 Thread Depth 9.5 9.5 9.5 9.5 9.5 9.5 9.5 The NAMUR slotted drive can be moved to the opposite side for field reversibility. 203, 204, and 205 sizes include a removable NAMUR adapter plate that can be moved to the opposite side. The NAMUR adapter plate covers the accessory side mounting patterns when installed. 10 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES DOUBLE SQUARE FEMALE DRIVE Dimensions and Technical Data (Metric, Millimeters) 203 204 205 207 210 212 214 DA SR DA SR DA SD SR DA SR DA SD SR DA SR DA SD SR F07 F07 F07 F14 F14 F25 F25 Square S1 17 17 17 36 36 55 55 Square Depth S2 33 33 33 25 25 46 46 Outer Diameter S3 22.1 22.1 22.1 48.0 48.0 72.9 72.9 Inner Diameter S4 19.1 19.1 19.1 40.6 40.6 61.7 61.7 Identical double square female drive on both sides of the actuator for all sizes AIR/FLUID VOLUME liters (L) Body 0.23-0.40-0.72 - - 1.81-2.72 - - 4.95-7.69 - - End Caps 0.15 0.25 0.49 0.97 1.92 2.67 5.34 PORT SIZE P1, P2, P3 Normal 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT 1/4" NPT Max 1/2" NPT 1/2" NPT 1/2" NPT 3/4" NPT 3/4" NPT 1" NPT 1" NPT STROKE TIME seconds Normal 0.25 0.5 0.5 1 1 3 3 Min 0.01 0.015 0.015 0.03 0.03 0.05 0.05 *Stroke time varies with supply pressure, temperature, spring rate, travel adjustment, working medium, piping, accessory flow rates, and valve torque. Values shown with no valve resistance. CENTER OF GRAVITY COGx 10 11 11 12 0 23 0 22 22 0 0 0 24 28 0 1 0 COGy 3 3 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 COGz* 27/31 39/42 28/33 46/53 0.00 13/19 0.00 47/57 104/112 0.00 41/55 0.00 56/71 114/124 0.00 43/51 0.00 *CoGz is variable for some models and changes with actuator stroke. Values are shown as min/max. WEIGHT kilograms (kg) MAX PRESSURE bar QS - Stainless 2.7 3.2 6.4 7.7 10.0 11.4 13.2 15.0 23.2 23.6 31.8 40.0 39.5 51.4 57.3 68.6 80.5 QD - Ductile 2.3 2.7 5.5 6.4 8.6 9.5 10.9 13.2 20.5 20.0 27.3 35.5 35.5 46.4 50.5 60.5 70.5 10.34 10.34 10.34 10.34 10.34 10.34 10.34 TEMPERATURE LIMITS LOW STANDARD HIGH Environmental temperature requirements may limit the use of certain trim materials. Temperature ranges may be extended with proper insulation. Ductile iron units may be used in low temperature (less than -28ºC), but stroke speed should be limited -51ºC to 85ºC -28ºC to 85ºC -28ºC to 204ºC to prevent brittle fracture. Extended temperature ranges available upon request. www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 11

QTRCO, INC. PRODUCT BULLETIN PRESSURE EQUIPMENT DIRECTIVE CATEGORY CLASSIFICATION The European Pressure Equipment Directive (PED, 2014/68/EU, supersedes 97/23/EC) requires equipment to be placed in categories based on Fluid Group and BarLiter rating. Determination of Fluid Group is the responsibility of the End User. QTRCO Q2-Series actuator ratings are listed below: Model Barliter Rating CATEGORY Fluid Group 2 For Fluid Group 1 Q203SR 1.52 SEP SEP Q203SP1 2.37 SEP SEP Q204SR 2.88 SEP SEP Q204SP1 4.39 SEP SEP Q205SD 5.59 SEP SEP Q205SR 5.59 SEP SEP Q205SP1 8.81 SEP SEP Q205SE-C1 6.71 SEP SEP Q205SE-C2 8.94 SEP SEP Q207SR 11.18 SEP SEP Q207SP1 17.88 SEP SEP Q210SD 22.52 SEP SEP Q210SR 22.52 SEP SEP Q210SP1 35.90 SEP 1 Q210SE-C1 27.10 SEP 1 Q210SE-C2 36.04 SEP 1 Q212SR 29.64 SEP 1 Q212SP1 47.15 SEP 1 Q214SR 59.11 1 2 Q214SP1 94.30 1 2 Q214SE-C1 71.00 1 2 Q214SE-C2 94.57 1 2 Model Barliter Rating CATEGORY Fluid Group 2 For Fluid Group 1 Q203DA 2.03 SEP SEP Q203DP1 2.61 SEP SEP Q204DA 5.42 SEP SEP Q204DP1 5.42 SEP SEP Q205DA 8.30 SEP SEP Q205DP1 11.18 SEP SEP Q207DA 18.46 SEP SEP Q207DP1 18.46 SEP SEP Q210DA 31.50 SEP 1 Q210DP1 44.88 SEP 1 Q212DA 53.69 1 2 Q212DP1 53.69 1 2 Q214DA 82.82 1 2 Q214DP1 118.21 1 2 Ratings are shown at maximum operating pressure. Models that fall under SEP are below the minimum BarLiter rating and not required to comply with the PED. 12 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES OUTPUT TORQUE DATA The following tables show output torque for common pressures. For additional output information, download the interactive toque tables at QTRCO.com. Actuators may generate more torque than the maximum rating at higher pressures (refer to page 6 for torque ratings). DOUBLE ACTING (in-lb) 20 psig 40 psig 60 psig 80 psig 100 psig 120 psig 140 psig 150 psig 203DA 84 168 252 336 420 504 588 630 204DA 149 298 448 597 746 895 1045 1119 205DA 298 597 895 1194 1492 1791 2089 2238 207DA 571 1142 1713 2284 2855 3426 3997 4283 210DA 1142 2284 3426 4568 5711 6853 7995 8566 212DA 1671 3343 5014 6685 8357 10028 11699 12535 214DA 3343 6685 10028 13371 16713 20056 23399 25070 DOUBLE ACTING (N-m) 1.5 bar 3 bar 4 bar 5.5 bar 7 bar 8 bar 9.5 bar 10.34 bar 203DA 10 21 28 38 48 55 65 71 204DA 18 37 49 67 86 98 116 126 205DA 37 73 98 134 171 196 232 253 207DA 70 140 187 257 328 374 445 484 210DA 140 281 374 515 655 749 889 968 212DA 205 411 548 753 959 1096 1301 1416 214DA 411 822 1096 1506 1917 2191 2602 2832 MAX RATED TORQUE - Actuators should not be sized above their maximum torque rating unless there is no possibility that the valve will resist with a value above that rating. SIZE: 203 204 205 207 210 212 214 in-lb: 500 825 1650 3300 6600 10500 21000 N-m: 56 93 186 373 746 1186 2373 www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 13

QTRCO, INC. PRODUCT BULLETIN OUTPUT TORQUE DATA (CONTINUED) SPRING RETURN (in-lb) SPRINGS 20 psig 40 psig 60 psig 80 psig 100 psig 120 psig 140 psig 150 psig START END START END START END START END START END START END START END START END START END 203SR-S10 90 55 113 78 197 162 281 251 365 330 449 414 533 498 575 540 203SR-S20 121 88 80 47 164 131 248 215 332 299 416 383 500 467 542 509 203 203SR-S30 154 101 67 14 151 98 235 182 319 266 403 350 487 434 529 476 203SR-S40 200 139 113 52 197 136 281 220 365 304 449 388 491 430 203SR-S50 221 161 91 31 175 115 259 199 343 283 427 367 469 409 204SR-S10 131 102 47 18 196 167 346 317 495 466 644 615 793 764 943 914 1017 988 204SR-S20 176 147 151 122 301 272 450 421 599 570 748 719 898 869 972 943 204SR-S30 257 191 107 41 257 191 406 340 555 489 704 638 854 788 928 862 204 204SR-S40 301 237 211 147 360 296 509 445 658 594 808 744 882 818 204SR-S50 343 249 199 105 348 254 497 403 646 552 796 702 870 776 204SR-S60 388 295 153 60 302 209 451 358 600 507 750 657 824 731 204SR-S70 502 376 221 95 370 244 519 393 669 543 743 617 205SD-S30 257 191 107 41 406 340 704 638 1003 937 1301 1235 1600 1534 1898 1832 2047 1981 205SD-S40 301 237 360 296 658 594 957 893 1255 1191 1554 1490 1852 1788 2001 1937 205SD-S50 343 249 348 254 646 552 945 851 1243 1149 1542 1448 1840 1746 1989 1895 205SD-S60 388 295 302 209 600 507 899 806 1197 1104 1496 1403 1794 1701 1943 1850 205SD-S70 502 376 221 95 519 393 818 692 1116 990 1415 1289 1713 1587 1862 1736 205 205SR-S10 262 204 94 36 393 335 691 633 990 932 1288 1230 1587 1529 1885 1827 2034 1976 205SR-S20 352 294 303 245 601 543 900 842 1198 1140 1497 1439 1795 1737 1944 1886 205SR-S30 514 382 215 83 513 381 812 680 1110 978 1409 1277 1707 1575 1856 1724 205SR-S40 602 474 421 293 720 592 1018 890 1317 1189 1615 1487 1764 1636 205SR-S50 686 498 397 209 696 508 994 806 1293 1105 1591 1403 1740 1552 205SR-S60 776 590 305 119 604 418 902 716 1201 1015 1499 1313 1648 1462 205SR-S70 1,004 752 442 190 740 488 1039 787 1337 1085 1486 1234 207SR-S09 584 462 680 558 1251 1129 1822 1700 2393 2271 2964 2842 3535 3413 3821 3699 207SR-S11 765 568 574 377 1145 948 1716 1519 2287 2090 2858 2661 3429 3232 3715 3518 207SR-S12 871 695 447 271 1018 842 1589 1413 2160 1984 2731 2555 3302 3126 3588 3412 207 207SR-S13 993 764 378 149 949 720 1520 1291 2091 1862 2662 2433 3233 3004 3519 3290 207SR-S31 1,455 1,157 556 258 1127 829 1698 1400 2269 1971 2840 2542 3126 2828 207SR-S32 1,636 1,263 450 77 1021 648 1592 1219 2163 1790 2734 2361 3020 2647 207SR-S33 1,757 1,332 952 527 1523 1098 2094 1669 2665 2240 2951 2526 MAX RATED TORQUE - Actuators should not be sized above their maximum torque rating unless there is no possibility that the valve will resist with a value above that rating. SIZE: 203 204 205 207 210 212 214 in-lb: 500 825 1650 3300 6600 10500 21000 14 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES OUTPUT TORQUE DATA (CONTINUED) SPRING RETURN (in-lb) SPRINGS 20 psig 40 psig 60 psig 80 psig 100 psig 120 psig 140 psig 150 psig START END START END START END START END START END START END START END START END START END 210SD-S09 584 462 680 558 1822 1700 2964 2842 4106 3984 5249 5127 6391 6269 7533 7411 8104 7982 210SD-S11 765 568 574 377 1716 1519 2858 2661 4000 3803 5143 4946 6285 6088 7427 7230 7998 7801 210SD-S12 871 695 447 271 1589 1413 2731 2555 3873 3697 5016 4840 6158 5982 7300 7124 7871 7695 210SD-S13 993 764 378 149 1520 1291 2662 2433 3804 3575 4947 4718 6089 5860 7231 7002 7802 7573 210SD-S31 1,455 1,157 1127 829 2269 1971 3411 3113 4554 4256 5696 5398 6838 6540 7409 7111 210SD-S32 1,636 1,263 1021 648 2163 1790 3305 2932 4448 4075 5590 5217 6732 6359 7303 6930 210 210SD-S33 1,757 1,332 952 527 2094 1669 3236 2811 4379 3954 5521 5096 6663 6238 7234 6809 210SR-S09 1,168 924 1360 1116 2502 2258 3644 3400 4787 4543 5929 5685 7071 6827 7642 7398 210SR-S11 1,529 1,136 1148 755 2290 1897 3432 3039 4575 4182 5717 5324 6859 6466 7430 7037 210SR-S12 1,743 1,390 894 541 2036 1683 3178 2825 4321 3968 5463 5110 6605 6252 7176 6823 210SR-S13 1,986 1,528 756 298 1898 1440 3040 2582 4183 3725 5325 4867 6467 6009 7038 6580 210SR-S31 2,911 2,314 1112 515 2254 1657 3397 2800 4539 3942 5681 5084 6252 5655 210SR-S32 3,272 2,527 899 154 2041 1296 3184 2439 4326 3581 5468 4723 6039 5294 210SR-S33 3,515 2,665 1903 1053 3046 2196 4188 3338 5330 4480 5901 5051 212SR-S10 2,960 1,990 1353 383 3024 2054 4695 3725 6367 5397 8038 7068 9709 8739 10545 9575 212 212SR-S20 3,158 2,358 985 185 2656 1856 4327 3527 5999 5199 7670 6870 9341 8541 10177 9377 212SR-S30 3,915 2,639 2375 1099 4046 2770 5718 4442 7389 6113 9060 7784 9896 8620 212SR-S40 4,860 3,510 1504 154 3175 1825 4847 3497 6518 5168 8189 6839 9025 7675 214SD-S20 3,158 2,358 985 185 4327 3527 7670 6870 11013 10213 14355 13555 17698 16898 21041 20241 22712 21912 214SD-S30 3,915 2,639 4046 2770 7389 6113 10732 9456 14074 12798 17417 16141 20760 19484 22431 21155 214SD-S40 4,860 3,510 3175 1825 6518 5168 9861 8511 13203 11853 16546 15196 19889 18539 21560 20210 214 214SR-S10 5,920 3,980 2705 765 6048 4108 9391 7451 12733 10793 16076 14136 19419 17479 21090 19150 214SR-S20 6,316 4,716 1969 369 5312 3712 8655 7055 11997 10397 15340 13740 18683 17083 20354 18754 214SR-S30 7,830 5,278 4750 2198 8093 5541 11435 8883 14778 12226 18121 15569 19792 17240 214SR-S40 9,720 7,020 3008 308 6351 3651 9693 6993 13036 10336 16379 13679 18050 15350 MAX RATED TORQUE - Actuators should not be sized above their maximum torque rating unless there is no possibility that the valve will resist with a value above that rating. SIZE: 203 204 205 207 210 212 214 in-lb: 500 825 1650 3300 6600 10500 21000 www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 15

QTRCO, INC. PRODUCT BULLETIN OUTPUT TORQUE DATA (CONTINUED) SPRING RETURN (N-m) SPRINGS 1.5 bar 3 bar 4 bar 5.5 bar 7 bar 8 bar 9.5 bar 10.34 bar START END START END START END START END START END START END START END START END START END 203SR-S10 10 6 14 10 21 17 32 28 42 38 49 45 59 55 65 61 203SR-S20 14 10 11 7 18 14 28 24 38 34 45 41 55 52 61 57 203 203SR-S30 17 11 9 3 16 10 26 20 37 31 44 38 54 48 60 54 203SR-S40 23 16 12 5 22 15 32 26 39 32 50 43 55 49 203SR-S50 25 18 9 3 20 13 30 23 37 30 47 40 53 46 204SR-S10 15 12 7 4 25 22 37 34 56 52 74 71 86 83 105 101 115 112 204SR-S20 20 17 20 17 32 29 51 47 69 66 81 78 100 96 110 107 204SR-S30 29 22 15 8 27 20 46 38 64 57 76 69 95 87 105 97 204 204SR-S40 34 27 22 15 40 33 59 52 71 64 89 82 100 92 204SR-S50 39 28 21 10 39 28 57 47 70 59 88 77 98 88 204SR-S60 44 33 16 5 34 23 52 42 64 54 83 72 93 83 204SR-S70 57 42 25 11 43 29 55 41 74 59 84 70 205SD-S30 29 22 15 8 52 44 76 69 113 105 150 142 174 167 211 203 231 224 205SD-S40 34 27 47 39 71 64 108 100 144 137 169 162 206 198 226 219 205SD-S50 39 28 45 35 70 59 106 96 143 132 167 157 204 194 225 214 205SD-S60 44 33 40 30 64 54 101 91 138 127 162 152 199 188 220 209 205SD-S70 57 42 31 17 55 41 92 78 129 114 153 139 190 176 210 196 205 205SR-S10 30 23 14 7 50 44 75 68 111 105 148 142 173 166 209 203 230 223 205SR-S20 40 33 40 34 65 58 101 95 138 131 162 156 199 193 220 213 205SR-S30 58 43 30 15 55 40 91 76 128 113 152 138 189 174 210 195 205SR-S40 68 54 44 30 81 66 118 103 142 128 179 164 199 185 205SR-S50 78 56 42 20 78 57 115 94 139 118 176 155 197 175 205SR-S60 88 67 31 10 68 47 105 83 129 108 166 145 186 165 205SR-S70 113 85 50 21 86 58 111 82 147 119 168 139 207SR-S09 66 52 88 74 135 121 205 191 275 262 322 308 392 379 432 418 207SR-S11 86 64 76 54 123 101 193 171 263 241 310 288 380 358 420 397 207SR-S12 98 79 62 42 109 89 179 159 249 229 296 276 366 346 405 385 207 207SR-S13 112 86 54 28 101 75 171 145 241 215 288 262 358 332 397 372 207SR-S31 164 131 56 23 127 93 197 163 244 210 314 280 353 319 207SR-S32 185 143 44 2 115 73 185 143 232 189 302 260 341 299 207SR-S33 199 150 107 59 177 129 224 176 294 246 333 285 MAX RATED TORQUE - Actuators should not be sized above their maximum torque rating unless there is no possibility that the valve will resist with a value above that rating. SIZE: 203 204 205 207 210 212 214 N-m: 56 93 186 373 746 1186 2373 16 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES OUTPUT TORQUE DATA (CONTINUED) SPRING RETURN (N-m) SPRINGS 1.5 bar 3 bar 4 bar 5.5 bar 7 bar 8 bar 9.5 bar 10.34 bar START END START END START END START END START END START END START END START END START END 210SD-S09 66 52 88 74 229 215 322 308 462 449 603 589 696 683 837 823 915 902 210SD-S11 86 64 76 54 217 194 310 288 451 428 591 569 684 662 825 803 903 881 210SD-S12 98 79 62 42 202 182 296 276 436 416 577 557 670 650 810 791 889 869 210SD-S13 112 86 54 28 194 169 288 262 428 402 569 543 662 636 803 777 881 855 210SD-S31 164 131 150 116 244 210 384 350 524 491 618 584 758 725 837 803 210SD-S32 185 143 138 96 232 189 372 330 512 470 606 564 746 704 825 783 210 210SD-S33 199 150 130 82 224 176 364 316 505 457 598 550 739 690 817 769 210SR-S09 132 104 176 149 270 242 410 383 551 523 644 617 785 757 863 836 210SR-S11 173 128 152 108 246 202 386 342 527 482 620 576 761 716 839 795 210SR-S12 197 157 124 84 217 177 358 318 498 458 592 552 732 692 811 771 210SR-S13 224 173 108 56 202 150 342 290 482 431 576 524 716 665 795 743 210SR-S31 329 261 113 45 253 186 394 326 487 420 628 560 706 639 210SR-S32 370 286 89 5 229 145 370 285 463 379 603 519 682 598 210SR-S33 397 301 214 118 354 258 448 351 588 492 667 570 212SR-S10 334 225 186 76 323 213 528 419 734 624 871 761 1076 967 1191 1082 212 212SR-S20 357 266 144 54 281 191 487 396 692 602 829 739 1035 944 1150 1059 212SR-S30 442 298 250 105 455 311 660 516 797 653 1003 859 1118 974 212SR-S40 549 397 357 204 562 409 699 546 904 752 1019 867 214SD-S20 357 266 144 54 555 465 829 739 1240 1150 1651 1560 1925 1834 2335 2245 2566 2475 214SD-S30 442 298 523 379 797 653 1208 1064 1619 1475 1893 1749 2304 2160 2534 2390 214SD-S40 549 397 425 273 699 546 1110 957 1521 1368 1794 1642 2205 2053 2435 2283 214 214SR-S10 669 450 372 153 646 427 1057 837 1467 1248 1741 1522 2152 1933 2382 2163 214SR-S20 714 533 289 108 563 382 974 793 1384 1204 1658 1477 2069 1888 2299 2118 214SR-S30 885 596 499 211 910 622 1321 1032 1595 1306 2006 1717 2236 1947 214SR-S40 1,098 793 713 408 1124 819 1398 1093 1809 1504 2039 1734 MAX RATED TORQUE - Actuators should not be sized above their maximum torque rating unless there is no possibility that the valve will resist with a value above that rating. SIZE: 203 204 205 207 210 212 214 N-m: 56 93 186 373 746 1186 2373 www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 17

QTRCO, INC. PRODUCT BULLETIN PARTS DIAGRAM & MATERIALS OF CONSTRUCTION Item No. Part Description Material (QS) Material (QD) 1 Body CF8M SST Ductile Iron 4 2 Shaft Retaining Ring 316 SST 316 SST 3 Shaft Thrust Washer 5 316 SST 316 SST 4 Top Hat Base Bolt 316 SST 316 SST 5 Top Hat Base 316 SST 316 SST 6 Top Hat 316 SST PM 316 SST PM 7 Top Hat Indicator Nylon 6/6 GF30 Nylon 6/6 GF30 8 Top Hat Bolt 316 SST 316 SST 9 Shaft O-Ring, Inner Option 2 Option 2 10 Shaft Bushing Option 2 Option 2 11 Shaft O-Ring, Outer Option 2 Option 2 12 Cylinder Seal PTFE PTFE 13 Spring Retainer 3 CF8M SST Ductile Iron 4 14 Rack CF8M SST CF8M SST 15 Spring, Inner 3 Chrome Silicon 1 Chrome Silicon 1 16 Spring, Outer 3 Chrome Silicon 1 Chrome Silicon 1 17 Safety Collar 3 316 SST 316 SST 18 Cylinder 316 SST 2 Black Amalgon 2 Item No. Part Description Material (QS) Material (QD) 19 Piston Bolt 316 SST 316 SST 20 Tie Rod 316 SST 316 SST 21 Piston Wiper Ring PTFE PTFE 22 Piston O-Ring Option 2 Option 2 23 Tie Rod Nut 316 SST 316 SST 24 End Cap CF8M SST Ductile Iron 4 25 Piston CF8M SST Ductile Iron 26 Travel Stop Nut 316 SST 316 SST 27 Travel Stop O-Ring Option 2 Option 2 28 Travel Stop A 316 SST 316 SST 29 Piston Set Screw 316 SST 316 SST 30 Travel Stop B 316 SST 316 SST 31 Shaft CF8M SST CF8M SST 32 Shaft Shoulder Washer 5 316 SST 316 SST 33 Saddle Thrust Washer Bronze Bronze 34 Saddle Roller 316 SST NIT 316 SST NIT 35 Saddle Pin O-Ring Option 2 Option 2 36 Saddle Pin 316 SST NIT 316 SST NIT 1: Chrome Silicon springs are powder coated. Stainless Steel springs available. 2: Option materials depend on trim code, see engineering string. 3: These parts not present on Double Acting models. 4: Ductile iron components are protected with a resilient E-coating. 5: Not present on 203, 204, or 205 models. CF8 stainless steel may be upgraded to 316 or CF8M stainless steel based on availability or customer request. Materials shown are standard. Other materials available, contact QTRCO for special options. Special coatings, plating, or surface treatments are also available 18 Q-SERIES ¼ TURN ACTUATORS www.qtrco.com

QTRCO, INC. PRODUCT BULLETIN QSERIES ENGINEERING STRING For ordering actuators with standard options and trim, specify items 1-8 and 16 as applicable. QTRCO will choose the appropriate trim., 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Model (1) Action (4) PST/SZ Angle (5) Temp Limits (8) O-Rings (13) Options (Separate multiple options with a comma) QS Stainless Steel DA* Double Acting Axx T Custom Range 40 Custom JR Jackscrew. Handwheel size and material specified QD Ductile Iron SD* Spring Return with 1 additional SP actuators: Angle of travel Q -76ºF to 310ºF 41 Buna N separately. cylinder to compress springs as measured from the piston G -60F to 185F 42 Viton HR Hydraulic override, cylinders only. Pump and reservoir (usually for low supply pressure fully inward position that M* -20F to 185F 43 Silicon specified separately. applications) valve will be allowed to travel H -20F to 400F 44 EPDM ETSxx.yy XX: Travel Adjustment End Cap Side during partial stroke test. YY: Travel Adjustment Body Side SR* Spring Return, Fail to 0 or 90 degrees SZ actuators: Angle (from Grade (2) SY Spring Return, Fail to 45 degrees fully CCW position) of fail position for SZ actuator. SZ Spring Return, Fail to other angles Example: for an SZ actuator 10 Custom C* Commercial N Nuclear SPa Spring Return with partial stroke (Xrciser) add-on. Replace a with number of partial stroke positions (standard is 1) that travels 30deg CW and 60 degrees CCW, this field would be A30 203 204 205 207 210 212 214 SEa Spring Return with tandem cylinders to assist spring compression. Replace a with number of tandem pistons (Standard is 1 per spring cylinder) SPaEb Spring Return with partial stroke (Xrciser) add-on and tandem cylinders to assist spring compression. Replace a with number of partial stroke positions (standard is 1). Replace b with number of tandem pistons (Standard is 1 per spring cylinder) DPa Double Acting with partial stroke (Xrciser) add-on. Replace a with number of partial stroke positions (standard is 1) Spring Material (9) 11* Chrome Silicon 12 17-7 PH Stainless Cylinder Material (10) Cylinder End Seals (14) 50 Custom 51* PTFE 52 Grafoil Grease (15) U Custom 60 Custom A* Amalga 61* Standard L Aluminum 62 Food Grade C Carbon Steel 63 Nuclear Grade S* Stainless Steel Size (3) Spring Set (6) Bushings (11) Orientation (16) Sxx Choose spring set based on required torque (N/A for DA and DP models). 20 Custom 21* Acetal 2 22* Bronze Filled PTFE 23 PEEK 24 Carbon Filled PTFE Port Size (7) Wiper Rings (12) P00 Custom 30 Custom P01* 1/4 NPT 31* PTFE 32 UHMWPE P02 3/8 NPT 33 PEEK P03 1/2 NPT P04 3/4 NPT P05 1 NPT LH* Left Hand. Pistons move outward to turn the valve clockwise. This is commonly called "Fail Closed" for spring return actuators. RH Right Hand. Pistons move outward to turn the valve counterclockwise. This is commonly called "Fail Open" for spring return actuators. TMLOx TMXAyy TMXByy Example: 15.80 (65 degrees total travel): A spring return actuator would fail to a 15 degree position in both LH and RH (fail-open or fail-closed) models, and would stroke with pressure to an 80 degree position (65 degrees total travel). An LH double acting model would stroke clockwise to the 15 degree position, and counter clockwise to the 80 degree position. Top mounted lockout. Replace x with lock position: 1: locks in full clockwise position 2: locks in full counterclockwise position 3: locks in both CW and CCW positions Cyy: locks in a position other than full CW or full CCW. Replace yy with lockout angle as measured from the fully clockwise position. Top mounted mechanical partial stroke test device that allows a test in the fully clockwise position. Replace yy with angle of motion to allow (max 30%) Top mounted mechanical partial stroke test device that allows a test in the fully counterclockwise position. Replace yy with angle of motion to allow (max 30%) Modifier (18) 3-digit number used by QTRCO to identify further customization. Contact QTRCO for details. SEP PED Pressure Equipment Directive (19) Actuator will be provided based on SEP with appropriate documentation Actuator will be provided as fully PED compliant NOTES:* items are considered standard Ensure material compatibility of all components with applications requirements.(7) Port size limited by actuator size. 203, 204, 205: P03 MAX. 207, 210: P04 MAX. 212, 214: P05 MAX (8) Environmental temperature requirements may limit the use of certain trim materials. Temperature ranges may be extended with proper insulation. Ductile iron units may be used in low temperature (less than -20F), but stroke speed should be limited to prevent brittle fracture. Allowable temperature on SP units may be limited by selected sensors (specified separately). (9) Standard springs are various grades of spring steel, most commonly chrome silicon, with powder coat. (15) QTRCO selects the appropriate grease based on application requirements. (17) Multiple compatible options may be chosen. Separate options with a comma. (18) This number is assigned by QTRCO for modifications that cannot be defined by the engineering string. Contact QTRCO for details about specific modifiers. (19) Omit if not required. SAMPLE SPECIFICATIONS QSCxxxSR-Sxx-P01-M-11-S-21-31-41-51-61-LH QDCxxxDA-P01-G-A-21-31-43-51-61-LH-SEP QDCxxxSR-Sxx-P01-H-11-G-22-31-42-51-61-LH QSCxxxSD-Sxx-P01-H-11-S-22-31-42-51-61-LH QDCxxxSP1-A15-S40-P04-G-11-A-21-31-43-51-61-LH QDCxxxDA-P01-H-11-G-22-31-42-51-61-LH-PED QSNxxxSR-S20-P01-M-12-S-23-33-44-52-63-RH-JR,TMLO3 QDCxxxSP1-A15-S40-P04-G-12-S-24-31-43-51-62-LH QSCxxxSE2-S10-P05-C-12-S-24-31-43-51-0-LH-HR,TMXA20-123 DESCRIPTION Standard stainless SR actuator with medium temp trim. Standard ductile iron DA actuator with low temp trim, SEP documentation required. Standard ductile iron SR actuator with high temp trim. Standard stainless SD actuator with high temp trim. Ductile iron, 1 position partial stroke at 15degrees, ¾ NPT ports, low temp trim. Ductile iron, high temp trim, full PED compliance required. Stainless, nuclear grade with medium temp nuclear trim and stainless springs. Right hand (fail open) orientation with lockout that locks in the actuated and failed positions, jackscrew override. Ductile iron, 1 position partial stroke at 15degrees, ¾ NPT ports, low temp trim stainless springs and cylinders, carbon filled PTFE bushings, food grade grease Stainless, Spring return with two tandem cylinders, 1inch NPT ports, custom range temperature trim, stainless springs, stainless cylinders, Carbon filled PTFE bushings, PTFE wiper rings, silicon o-rings, PTFE cylinder seals, custom grease, left hand fail, with hydraulic override and TMX manual partial stroke device that strokes 20degrees from clockwise. 123 modifier code defines custom grease, temperature range, and a custom coating requested by customer. www.qtrco.com Q-SERIES ¼ TURN ACTUATORS 19

The Leader in Actuator Technology DCN00650(11)