Alarms & Remote Start Automotive Data Solutions Inc. INSTALL UIDE ADS-AL(DL-TL-EN TL Available for : ADS-AL CA Rev. Date: July 0, 0 Doc. No.: #### The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0! NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation uide carefully before beginning any work.
ADS-AL(DL-TL-EN Page of 9 0070 Doc. No.: #### install TYPE SELECTiOn FEATURES TRUNK/HATCH RELEASE LS00h 08- LX70 08- LandCruiser 08- INSTALL TYPE MAKE HOOD STATUS OUTPUT* DOOR UNLOCK TRUNK STATUS OUTPUT DOOR LOCK DOOR STATUS OUTPUT DISARM OEM ALARM E-BRAKE OUTPUT ARM OEM ALARM BRAKE PEDAL STATUS OUTPUT PUSH TO START CTRL TACHOMETER OUTPUT DATA IMMOBILIZER BYPASS Keyless and smartkey systems will remain functional during remote start. AS TANK FLAP RELEASE YEAR 07- I POWER LIFTATE MODEL LEXUS LS0 TOYOTA NOTE * Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 0
XX-XX AL(DL-TL T&/ TL PAE X-X Page of 9 ADS-AL(DL-TL-EN Doc. No.: #### 0070 COMPOnEnT LOCATOr A A : MAIN BODY ECU Automotive Data Solutions Inc. 0
ADS-AL(DL-TL-EN Page of 9 Doc. No.: #### 0070 COLOR TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH pin ray (DATA CanL pin Red (DATA STSW 0 pin 0 Red pin Black V 0 pin 0 Black Parking light pin Purple (- pin 07 White (- Push button CanH pin ray (DATA CanL pin Red (DATA STSW 0 pin 0 Red pin Black V 0 pin 0 Black Parking light pin Purple (- pin 07 White (- Push button 08- Ignition 08- Ignition WIRE COLOR NAME LandCruiser YEAR MODEL LX70 WIRE DESCRIPTION TOYOTA LEXUS MAKE TYPE - wire CrOSS reference CHArT - OF Automotive Data Solutions Inc. 0
ADS-AL(DL-TL-EN Page of 9 0070 Doc. No.: #### TYPE - wiring DIARAM MAIN BODY ECU 7 0 9 8 7 0 9 8 0 9 8 7 (- 0 9 8 7 0 I NI TI WARNIN: DO NOT CONNECT ANY OTHER ACCESSORY,INITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLIN THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. NL CA T H LI 9 8 7 NH CA IN RK PA ON 0 9 8 7 SW ST REMOTE STARTER V PARKIN LIHT (- OUTPUT TACH (AC INPUT E-BRAKE STATUS (- INPUT STARTER OUTPUT LIFTATE (- OUTPUT UNLOCK/DISARM (- OUTPUT LOCK/ARM (- OUTPUT V ROUND (- ROUND WHEN RUNNIN (- OUTPUT <- OPTIONAL 7. AMPS OPTIONAL -> OPTIONAL -> V INPUT INITION INPUT BRAKE INPUT HOOD STATUS (- INPUT TRUNK STATUS (- INPUT DOOR STATUS (- INPUT DIODE N00 DATA MODE LEEND NOT REQUIRED IN DATA MODE (-WAY NOT REQUIRED IN DATA MODE (-WAY USE DATA MODE OR HARDWIRE MODE DATA MODE WR (- INPUT - BLUE/WHITE (NC WHITE ROUND (- - BLACK V - RED LOCK/ARM (- INPUT - REEN/BLACK UNLOCK/DISARM (- INPUT - BLUE/BLACK LIFTATE (- INPUT - RED/WHITE (NC BROWN (NC PURPLE/YELLOW (NC PURPLE/BLACK (NC WHITE STARTER INPUT - BLACK/WHITE E-BRAKE STATUS (- OUTPUT - REEN TACH (AC OUTPUT - PURPLE/WHITE WHITE/BLACK - STSW OUTPUT WHITE/RED (NC WHITE - INITION INPUT YELLOW/BLACK - DOOR STATUS (- OUTPUT YELLOW/RED - TRUNK STATUS (- OUTPUT YELLOW - HOOD STATUS (- OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANE/BLACK (NC ORANE/WHITE (NC ORANE - BRAKE OUTPUT PINK/BLACK (NC PINK - INITION INPUT BLUE/RED - ROUND (- INPUT BLUE/YELLOW - (- OUTPUT REEN/RED (NC REEN/YELLOW (NC RAY/RED (NC RAY/YELLOW (NC CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED ENINE START STOP 8 9 0 7 PT S (- IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENIN VEHICLE DOOR ENINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. Automotive Data Solutions Inc. 0
ADS-AL(DL-TL-EN Page of 9 Doc. No.: #### 0070 COLOR TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH pin Black (DATA CanL pin White (DATA STSW 0 pin 0 Black 8 pin Pink V 0 pin 0 Yellow Parking light White 0 pin 8 Blue (- Parking light switch pin 07 White (- Push button CanH pin Black (DATA CanL pin White (DATA STSW 0 pin 0 Black 8 pin Pink V 0 pin 0 Yellow Parking light White 0 pin 8 Blue (- Parking light switch pin 07 White (- Push button 07- Ignition 08- Ignition WIRE COLOR NAME LS00h YEAR MODEL LS0 WIRE DESCRIPTION TOYOTA LEXUS MAKE TYPE - wire CrOSS reference CHArT - OF Automotive Data Solutions Inc. 0
ADS-AL(DL-TL-EN Page 7 of 9 0070 Doc. No.: #### TYPE - wiring DIARAM WHITE AT PARKIN LIHT SWITCH MAIN BODY ECU BACK SIDE 0 9 8 7 0 9 8 7 0 9 8 7 NL CA IN NH CA RK PA LI HT (- I 0 9 8 7 0 9 8 7 8 7 NI TI ON WARNIN: DO NOT CONNECT ANY OTHER ACCESSORY,INITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLIN THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. 0 9 8 7 SW ST V REMOTE STARTER PARKIN LIHT (- OUTPUT TACH (AC INPUT E-BRAKE STATUS (- INPUT STARTER OUTPUT AS TANK FLAP RELEASE (- OUTPUT TRUNK (- OUTPUT UNLOCK/DISARM (- OUTPUT LOCK/ARM (- OUTPUT V ROUND (- ROUND WHEN RUNNIN (- OUTPUT <- OPTIONAL 7. AMPS OPTIONAL -> OPTIONAL -> V INPUT INITION INPUT BRAKE INPUT HOOD STATUS (- INPUT TRUNK STATUS (- INPUT DOOR STATUS (- INPUT DIODE N00 DATA MODE LEEND NOT REQUIRED IN DATA MODE (-WAY NOT REQUIRED IN DATA MODE (-WAY USE DATA MODE OR HARDWIRE MODE DATA MODE WR (- INPUT - BLUE/WHITE (NC WHITE ROUND (- - BLACK V - RED LOCK/ARM (- INPUT - REEN/BLACK UNLOCK/DISARM (- INPUT - BLUE/BLACK TRUNK (- INPUT - RED/WHITE (NC BROWN AS TANK FLAP RELEASE (- INPUT - PURPLE/YELLOW (NC PURPLE/BLACK (NC WHITE STARTER INPUT - BLACK/WHITE E-BRAKE STATUS (- OUTPUT - REEN TACH (AC OUTPUT - PURPLE/WHITE WHITE/BLACK - STSW OUTPUT WHITE/RED (NC WHITE - INITION INPUT YELLOW/BLACK - DOOR STATUS (- OUTPUT YELLOW/RED - TRUNK STATUS (- OUTPUT YELLOW - HOOD STATUS (- OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANE/BLACK (NC ORANE/WHITE (NC ORANE - BRAKE OUTPUT PINK/BLACK (NC PINK - INITION INPUT BLUE/RED - ROUND (- INPUT BLUE/YELLOW - (- OUTPUT REEN/RED (NC REEN/YELLOW (NC RAY/RED (NC RAY/YELLOW (NC IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENIN VEHICLE DOOR ENINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENINE START STOP 8 9 0 7 PT S (- CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED Automotive Data Solutions Inc. 0
ADS-AL(DL-TL-EN Page 8 of 9 Doc. No.: #### 0070 installation MODE SELECTiOn Press and release programming button to select installation mode. LED flashes (X once = DATA MODE LED flashes (X twice = STANDARD HARDWIRE MODE Press and hold programming button until LED turns solid REEN to register selection.! After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PrOgrAMMing PrOCEDUrE NOTE I Between each step, LED will turn solid RED, this is the default standby mode. Æ ENINE START STOP x Push start button twice [x] to ON position. Æ ENINE START STOP x Push start button once [x] to OFF position. Module Programming Procedure completed. Wait, LED will turn solid REEN then will turn OFF. Automotive Data Solutions Inc. 0
XX-XX CLASSIC - PAE X-X ADS-AL(DL-TL-EN Page 9 of 9 Doc. No.: #### 0070 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN, identify the 0th character then match it to its corresponding year. Æ AYNTAL8DR0X Æ A 980 L 990 Y 000 A 00 B 98 M 99 00 B 0 C 98 N 99 00 C 0 D 98 P 99 00 D 0 E 98 R 99 00 E 0 F 98 S 99 00 F 0 98 T 99 00 0 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 MODULE DiAgnOSTiCS LED STATUS DIANOSTICS DURIN PRORAMMIN DURIN REMOTE START WITH INITION OFF Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing REEN Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid REEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. DISCONNECT black -PIN standard or optional data connector. DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data connector. FACTOrY reset PrOCEDUrE PRESS AND HOLD programming button while connecting either -PIN standard or optional data connector. 7 Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENINE error message. When LED flashes red, RELEASE programming button. Automotive Data Solutions Inc. 0