Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-MI3-EN AVAILABLE FOR : ADS-AL CA Rev. Date: June 9, 08 Doc. No.: ##5396## MI3 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 08 TERMS OF USE: Automotive Data solutions inc. ( ADs ) products are strictly intended for installation by Certified technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADs product in a vehicle, it is the Certified technician s responsibility to review the most current Product Guide, install Guide and vehicle-specific notes available in Weblink. ADs is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADs reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non- Certified technicians, non-compliant Certified technicians or end users.
Page of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 INSTALL TYPE SELECTION FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS PRIORITY UNLOCK** DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE A/M ALARM CTRL FROM OEM REMOTES A/M RS CTRL FROM OEM REMOTES HOOD STATUS OUTPUT*** DOOR STATUS OUTPUT TRUNK STATUS OUTPUT MITSUBISHI BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT RAP SHUTDOWN CTRL SECURE TAKEOVER TACHOMETER OUTPUT Outlander PTS AT* 4-8 Eclipse Cross PTS AT* 8 *The door handle request switch will not be functional during the remote start sequence. **Available only when the ignition is OFF. *** Available only if vehicle is equipped with factory hood switch.
Page 3 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 TYPE - WIRE CROSS REFERENCE CHART MAKE MITSUBISHI MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR V C40 Black 0 pin 0 Red (+) ETACS fuse panel ~ Ignition C40 White 08 pin 0 Brown/Red (+) ETACS fuse panel ~ Outlander PTS AT 4-8 Starter C40 White 3 pin 09 Purple (+) ETACS fuse panel ~ CanH C6 White pin 0 White (DATA) CAN junction connector, near firewall, driver side ~ CanL C6 White pin Green (DATA) CAN junction connector, near firewall, driver side ~ Parking Light (R) C48 White 3 pin 03 Black/White (+) ETACS fuse panel ~ Parking Light (L) C48 White 3 pin 06 White/Black (+) ETACS fuse panel ~ PTS C04 White 0 pin 04 Green/Red (+) PTS button ~ PTS C04 White 0 pin 0 Yellow (-) PTS button ~
Page 4 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 TYPE - WIRING DIAGRAM CANH CANL STARTER (+) 6 7 8 9 0 4 5 3 C40 - C6 JUNCTION (NEAR FIREWALL, DRIVER SIDE) ETACS/ECU 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 4 5 C48 - C40 6 7 8 9 0 3 4 5 6 7 8 IGNITION (+) PARKING LIGHT LEFT (+) PARKING LIGHT RIGHT (+) C40 BLACK V (+) 3 AMP N400 DIODE 3 AMP N400 DIODE REMOTE STARTER PARKING LIGHT (+) OUTPUT STARTER (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT DISARM (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE GROUND (-) INPUT V (+) INPUT IGNITION (+) OUTPUT BRAKE (+) INPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/ (NC) GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK RELEASE (-) INPUT - RED/ (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) STARTER (+) INPUT - BLACK/ E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/ /BLACK (NC) /RED (NC) (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/ (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT C04 PTS 3 4 5 BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - PTS (+) OUTPUT GREEN/YELLOW (NC) GRAY/RED - PTS (-) OUTPUT GRAY/YELLOW (NC) 6 7 8 9 0 PTS (+) PTS (-)
Page 5 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 TYPE - WIRE CROSS REFERENCE CHART MAKE MITSUBISHI MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR V ~ Black 0 pin 0 Black (+) ETACS fuse panel ~ Ignition ~ White 08 pin 0 Red (+) ETACS fuse panel ~ Eclipse Cross PTS AT 8 Starter ~ White 3 pin 09 LtBlue (+) ETACS fuse panel ~ CanH C44 White 36 pin 7 Yellow (DATA) ETACS fuse panel ~ CanL C44 White 36 pin 6 Red (DATA) ETACS fuse panel ~ Parking Light (R) C46 White 3 pin 03 Gray (+) ETACS fuse panel ~ Parking Light (L) C46 White 3 pin 06 White (+) ETACS fuse panel ~ PTS ~ White pin 06 White (+) PTS button ~ PTS ~ White pin 03 Purple (-) PTS button ~
Page 6 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 TYPE - WIRING DIAGRAM CANL CANH C44 - STARTER (+) 4 5 4 5 6 7 8 9 0 3 4 5 67 7 8 9 0 3 4 5 6 7 8 9 30 3 3 33 34 35 36 6 7 8 9 0 3 ETACS/ECU 4 5 46-6 7 8 9 0 3 4 5 6 7 8 IGNITION (+) PARKING LIGHT LEFT (+) PARKING LIGHT RIGHT (+) BLACK V (+) 3 AMP N400 DIODE 3 AMP N400 DIODE REMOTE STARTER PARKING LIGHT (+) OUTPUT STARTER (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT DISARM (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE GROUND (-) INPUT V (+) INPUT IGNITION (+) OUTPUT BRAKE (+) INPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/ (NC) GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK RELEASE (-) INPUT - RED/ (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) STARTER (+) INPUT - BLACK/ E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/ /BLACK (NC) /RED (NC) (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/ (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT PTS 4 5 6 7 8 9 0 BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - PTS (+) OUTPUT GREEN/YELLOW (NC) GRAY/RED - PTS (-) OUTPUT GRAY/YELLOW (NC) PTS (+) PTS (-)
Page 7 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE Æ Push start button twice [x] to x ON position. 3 ENGINE START STOP Æ x ENGINE START STOP Push start button once [x] to OFF position. Wait, LED will turn solid GREEN for seconds. 4 Module Programming Procedure completed.
Page 8 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ A 980 L 990 Y 000 A 00 B 98 M 99 00 B 0 C 98 N 99 00 C 0 D 983 P 993 3 003 D 03 E 984 R 994 4 004 E 04 F 985 S 995 5 005 F 05 G 986 T 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.
IMPORTANT Page 9 of 9 ADS-AL(DL)-MI3-EN Doc. No.: ##5396## 08069 WARNING: READ BEFORE REMOTE NOTICESTARTING THE VEHICLE I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - PTS - TO THE VEHICLE OWNER NOTE I È All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTIºN COMING UP! Unlock vehicle door using OEM or after-market remote. TIME RESTRICTIºN Within 45 SECONDS from previous step: 3! Open vehicle door. Enter vehicle. Close vehicle door. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown.