SECTION DIRECTORY Product Selection Guide Size and Performance Data... OSBF-2 Glazing Performance... OSBF-3 Grille Types... OSBF-7 Design Data Vent... OSBF-11 Detailed Product Descriptions... OSBF-14 Unit Sections... OSBF-15 The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are subject to change without notice. Consult your local Pella representative for up-to-date product information. OSBF-1
PRODUCT SELECTION GUIDE Size and Performance Data PERFORMANCE 1 Meets or Exceeds AAMA / WDMA Ratings Air Infiltration (cfm / ft 2 of frame @ 1.57 psf wind pressure) Water Resistance Design Pressure OTHER PERFORMANCE CRITERIA R35 Hallmark Certified Forced Entry Resistance Level (Minimum Security Grade) 2 10 0.30 6.24 psf Operating Force (lb) Initiate Motion / Maintain Motion (of Hallmark tested size and glazing) 3 15 / 6 35 psf STANDARD OPTIONS / UPGRADES GLAZING Glazing Type Dual-Pane Insulating Glass Triple-Pane Insulating Glass Insulated Glass Options/Low-E Types SunDefense Low-E AdvancedComfort Low-E Advanced Low-E NaturalSun Low-E Clear (no Low-E coating) Additional Glass Options Tempered Glass Gas Fill/High Altitude Argon EXTERIOR EnduraClad protective finish Obscure Glass 4 Tinted Glass (Bronze, Gray and Green) Krypton (Available with triple-pane glazing only) High altitude (with air) High altitude with argon EnduraClad Plus protective finish Cladding Colors 4 27 Standard colors Custom Colors INTERIOR Unfinished wood WOOD TYPES Pine HARDWARE Bright Brass, Satin Nickel or Oil Rubbed Bronze GRILLES Integral Light Technology Grilles Factory primed Factory prefinished paint (Not available with premium wood upgrade) Mahogany, Douglas Fir Traditional,, Top Row, Cross, New England, Victorian, Custom Roomside Removable Grilles Traditional,, Top Row, Cross, New England, Victorian, Custom Grilles-Between-the-Glass Traditional,, Cross, Top Row 1, Custom-Equally Divided (1) Maximum performance for six panel or less units when glazed with the appropriate glass thickness. See Design Data pages in this section for specific product performance. Contact your local sales representative for complete information. (2) The higher the level, the greater the product s ability to resist forced entry. (3) Glazing configurations may result in higher operational forces. (4) Contact your local Pella sales representative for current designs and color options. OSBF-2
GLAZING PERFORMANCE - TOTAL UNIT Contemporary Panel Glazing Thickness Type of Glazing NFRC Certified Product # Ext. Glass (mm) Int. Gap Fill U-Factor Performane Values1 SHGC VLT % CR Shaded Areas Meet ENERGY STAR Performance Criteria in Zones Shown U. S. Canada 2 Zone ER Zone VENT N NC SC S 1 2 3 13/16" Clear IG PEL-N-220-00001-00001 3 3 air 0.45 0.43 44 45 with grilles-between-the-glass PEL-N-220-00002-00001 0.45 0.37 37 45 with integral grilles PEL-N-220-00003-00001 0.45 0.37 37 45 13/16" Advanced Low-E IG PEL-N-220-00089-00001 3 3 argon 0.33 0.21 38 59 with grilles-between-the-glass PEL-N-220-00090-00001 0.33 0.18 32 59 with integral grilles PEL-N-220-00091-00001 0.33 0.18 32 59 13/16" SunDefenseTM Low-E IG PEL-N-220-00017-00001 3 3 argon 0.32 0.15 35 59 with grilles-between-the-glass PEL-N-220-00018-00001 0.32 0.14 29 59 with integral grilles PEL-N-220-00019-00001 0.33 0.14 29 59 13/16" AdvancedComfort Low-E IG PEL-N-220-00041-00001 3 3 argon 0.30 0.20 37 48 with grilles-between-the-glass PEL-N-220-00042-0001 0.30 0.18 31 48 with integral grilles PEL-N-220-00043-00001 0.30 0.18 31 48 13/16" NaturalSun Low-E IG PEL-N-220-00065-00001 3 3 argon 0.33 0.38 43 59 with grilles-between-the-glass PEL-N-220-00066-00001 0.33 0.32 36 59 with integral grilles PEL-N-220-00067-00001 0.34 0.32 36 59 TINTED GLAZING 13/16" Bronze Advanced Low-E IG PEL-N-220-00113-00001 5 3 argon 0.33 0.18 24 58 with grilles-between-the-glass PEL-N-220-00114-00001 0.33 0.16 21 58 with integral grilles PEL-N-220-00115-00001 0.34 0.16 21 58 13/16" Gray Advanced Low-E IG PEL-N-220-00129-00001 5 3 argon 0.33 0.17 21 58 with grilles-between-the-glass PEL-N-220-00130-00001 0.33 0.15 18 58 with integral grilles PEL-N-220-00131-00001 0.34 0.15 18 58 13/16" Green Advanced Low-E IG PEL-N-220-00145-00001 5 3 argon 0.33 0.21 33 58 with grilles-between-the-glass PEL-N-220-00146-00001 0.33 0.18 28 58 with integral grilles PEL-N-220-00147-00001 0.34 0.18 28 58 HIGH ALTITUDE GLAZING 13/16" Advanced Low-E IG PEL-N-220-00085-00001 3 3 air 0.35 0.21 38 57 with grilles-between-the-glass PEL-N-220-00086-00001 0.35 0.18 32 57 with integral grilles PEL-N-220-00087-00001 0.36 0.18 32 57 13/16" SunDefense Low-E IG PEL-N-220-00013-00001 3 3 air 0.35 0.16 35 58 with grilles-between-the-glass PEL-N-220-00014-00001 0.35 0.14 29 58 with integral grilles PEL-N-220-00015-00001 0.36 0.14 29 58 13/16" AdvancedComfort Low-E IG PEL-N-220-00037-00001 3 3 air 0.31 0.20 37 44 with grilles-between-the-glass PEL-N-220-00038-00001 0.31 0.18 31 44 with integral grilles PEL-N-220-00039-00001 0.32 0.18 31 44 13/16" NaturalSun Low-E IG PEL-N-220-00061-00001 3 3 air 0.36 0.38 43 57 with grilles-between-the-glass PEL-N-220-00062-00001 0.36 0.32 36 57 with integral grilles PEL-N-220-00063-00001 0.37 0.32 36 57 R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are for configurations with 6 panels or less and calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY STAR initiative. For center-glass values, see the Product Performance section. See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines. OSBF-3
GLAZING PERFORMANCE - TOTAL UNIT French Panel Glazing Thickness Type of Glazing NFRC Certified Product # Ext. Glass (mm) Int. Gap Fill U-Factor Performane Values1 SHGC VLT % CR Shaded Areas Meet ENERGY STAR Performance Criteria in Zones Shown U. S. Canada 2 Zone ER Zone VENT N NC SC S 1 2 3 13/16" Clear IG PEL-N-220-00193-00001 3 3 air 0.44 0.43 44 45 with grilles-between-the-glass PEL-N-220-00194-00001 0.44 0.37 37 45 with integral grilles PEL-N-220-00195-00001 0.45 0.37 37 45 13/16" Advanced Low-E IG PEL-N-220-00281-00001 3 3 argon 0.33 0.21 38 59 with grilles-between-the-glass PEL-N-220-00282-00001 0.33 0.18 32 59 with integral grilles PEL-N-220-00283-00001 0.33 0.18 32 59 13/16" SunDefenseTM Low-E IG PEL-N-220-00209-00001 3 3 argon 0.32 0.15 35 59 with grilles-between-the-glass PEL-N-220-00210-00001 0.32 0.14 29 59 with integral grilles PEL-N-220-00211-00001 0.33 0.14 29 59 13/16" AdvancedComfort Low-E IG PEL-N-220-00233-00001 3 3 argon 0.30 0.20 37 48 with grilles-between-the-glass PEL-N-220-00234-00001 0.30 0.18 31 48 with integral grilles PEL-N-220-00235-00001 0.30 0.18 31 48 13/16" NaturalSun Low-E IG PEL-N-220-00257-00001 3 3 argon 0.33 0.38 43 59 with grilles-between-the-glass PEL-N-220-00258-00001 0.33 0.32 36 59 with integral grilles PEL-N-220-00259-00001 0.34 0.32 36 59 TINTED GLAZING 13/16" Bronze Advanced Low-E IG PEL-N-220-00305-00001 5 3 argon 0.33 0.18 24 59 with grilles-between-the-glass PEL-N-220-00306-00001 0.33 0.16 21 59 with integral grilles PEL-N-220-00307-00001 0.35 0.14 17 59 13/16" Gray Advanced Low-E IG PEL-N-220-00321-00001 5 3 argon 0.33 0.17 21 59 with grilles-between-the-glass PEL-N-220-00322-00001 0.33 0.15 18 59 with integral grilles PEL-N-220-00323-00001 0.33 0.15 18 59 13/16" Green Advanced Low-E IG PEL-N-220-00337-00001 5 3 argon 0.33 0.21 33 59 with grilles-between-the-glass PEL-N-220-00338-00001 0.33 0.18 28 59 with integral grilles PEL-N-220-00339-00001 0.33 0.18 28 59 HIGH ALTITUDE GLAZING 13/16" Advanced Low-E IG PEL-N-220-00277-00001 3 3 air 0.35 0.21 38 57 with grilles-between-the-glass PEL-N-220-00278-00001 0.35 0.18 32 57 with integral grilles PEL-N-220-00279-00001 0.36 0.18 32 57 13/16" SunDefense Low-E IG PEL-N-220-00205-00001 3 3 air 0.35 0.16 35 58 with grilles-between-the-glass PEL-N-220-00206-00001 0.35 0.14 29 58 with integral grilles PEL-N-220-00207-00001 0.35 0.14 29 58 13/16" AdvancedComfort Low-E IG PEL-N-220-00229-00001 3 3 air 0.31 0.20 37 44 with grilles-between-the-glass PEL-N-220-00230-00001 0.31 0.18 31 44 with integral grilles PEL-N-220-00231-00001 0.32 0.18 31 44 13/16" NaturalSun Low-E IG PEL-N-220-00253-00001 3 3 air 0.36 0.38 43 57 with grilles-between-the-glass PEL-N-220-00254-00001 0.36 0.32 36 57 with integral grilles PEL-N-220-00255-00001 0.36 0.32 36 57 R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are for configurations with 6 panels or less and calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY STAR initiative. For center-glass values, see the Product Performance section. See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines. OSBF-4
GLAZING PERFORMANCE - TOTAL UNIT Contemporary Panel Triple-Pane Glazing Glazing Thickness Type of Glazing NFRC Certified Product # Glass (mm) Ext. Mid Int. Gap Fill U-Factor Performane Values1 SHGC VLT % CR Shaded Areas Meet ENERGY STAR Performance Criteria in Zones Shown U. S. Canada 2 Zone ER Zone VENT N NC SC S 1 2 3 1" Advanced Low-E IG PEL-N-220-161-00001 3 3 3 argon 0.29 0.18 29 59 with grilles-between-the-glass PEL-N-220-162-00001 0.29 0.15 25 59 with integral grilles PEL-N-220-163-00001 0.30 0.15 25 59 1" Advanced Low-E IG PEL-N-220-165-00001 3 3 3 krypton 0.27 0.18 29 59 15 with grilles-between-the-glass PEL-N-220-166-00001 0.27 0.15 25 59 14 with integral grilles PEL-N-220-167-00001 0.27 0.15 25 59 14 1" SunDefense Low-E IG PEL-N-220-185-00001 3 3 3 argon 0.29 0.14 31 59 with grilles-between-the-glass PEL-N-220-186-00001 0.30 0.13 26 59 with integral grilles PEL-N-220-187-00001 0.30 0.13 26 59 1" SunDefense Low-E IG PEL-N-220-189-00001 3 3 3 krypton 0.27 0.14 31 59 13 with grilles-between-the-glass PEL-N-220-190-00001 0.27 0.12 26 59 12 with integral grilles PEL-N-220-191-00001 0.28 0.12 26 59 11 1" NaturalSun Low-E IG PEL-N-220-173-00001 3 3 3 argon 0.29 0.31 37 59 with grilles-between-the-glass PEL-N-220-174-00001 0.30 0.27 32 59 with integral grilles PEL-N-220-175-00001 0.30 0.27 32 59 1" NaturalSun Low-E IG PEL-N-220-177-00001 3 3 3 krypton 0.27 0.31 37 59 23 with grilles-between-the-glass PEL-N-220-178-00001 0.28 0.27 32 59 19 with integral grilles PEL-N-220-179-00001 0.28 0.27 32 59 19 HIGH ALTITUDE GLAZING 1" Advanced Low-E IG PEL-N-220-157-00001 3 3 3 air 0.33 0.16 25 59 with grilles-between-the-glass PEL-N-220-158-00001 0.33 0.16 25 59 with integral grilles PEL-N-220-159-00001 0.33 0.13 21 59 1" SunDefense Low-E IG PEL-N-220-181-00001 3 3 3 air 0.32 0.15 31 59 with grilles-between-the-glass PEL-N-220-182-00001 0.33 0.13 26 59 with integral grilles PEL-N-220-183-00001 0.33 0.13 26 59 1" NaturalSun Low-E IG PEL-N-220-169-00001 3 3 3 air 0.32 0.31 37 59 with grilles-between-the-glass PEL-N-220-170-00001 0.33 0.27 32 59 with integral grilles PEL-N-220-171-00001 0.33 0.27 32 59 R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are for configurations with 6 panels or less and calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY STAR initiative. For center-glass values, see the Product Performance section. See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines. OSBF-5
GLAZING PERFORMANCE - TOTAL UNIT French Panel Triple-Pane Glazing Glazing Thickness Type of Glazing NFRC Certified Product # Glass (mm) Ext. Mid Int. Gap Fill U-Factor Performane Values1 SHGC VLT % CR Shaded Areas Meet ENERGY STAR Performance Criteria in Zones Shown U. S. Canada 2 Zone ER Zone VENT N NC SC S 1 2 3 1" Advanced Low-E IG PEL-N-220-00353-00001 3 3 3 argon 0.29 0.18 29 60 with grilles-between-the-glass PEL-N-220-00354-00001 0.30 0.15 25 60 with integral grilles PEL-N-220-00355-00001 0.30 0.15 25 60 1" Advanced Low-E IG PEL-N-220-00357-00001 3 3 3 krypton 0.27 0.18 29 60 15 with grilles-between-the-glass PEL-N-220-00358-00001 0.27 0.15 25 60 14 with integral grilles PEL-N-220-00359-00001 0.28 0.15 25 60 12 1" SunDefense Low-E IG PEL-N-220-00377-00001 3 3 3 argon 0.29 0.14 31 60 with grilles-between-the-glass PEL-N-220-00378-00001 0.30 0.13 26 60 with integral grilles PEL-N-220-00379-00001 0.30 0.13 26 60 1" SunDefense Low-E IG PEL-N-220-00381-00001 3 3 3 krypton 0.27 0.14 31 60 13 with grilles-between-the-glass PEL-N-220-00382-00001 0.28 0.12 26 60 11 with integral grilles PEL-N-220-00383-00001 0.28 0.12 26 60 11 1" NaturalSun Low-E IG PEL-N-220-00365-00001 3 3 3 argon 0.30 0.31 37 60 with grilles-between-the-glass PEL-N-220-00366-00001 0.30 0.27 32 60 with integral grilles PEL-N-220-00367-00001 0.30 0.27 32 60 1" NaturalSun Low-E IG PEL-N-220-00369-00001 3 3 3 krypton 0.28 0.31 37 60 22 with grilles-between-the-glass PEL-N-220-00370-00001 0.28 0.27 32 60 19 with integral grilles PEL-N-220-00371-00001 0.28 0.27 32 60 19 HIGH ALTITUDE GLAZING 1" Advanced Low-E IG PEL-N-220-00349-00001 3 3 3 air 0.32 0.18 29 59 with grilles-between-the-glass PEL-N-220-00350-00001 0.32 0.16 25 59 with integral grilles PEL-N-220-00351-00001 0.33 0.16 25 59 1" SunDefense Low-E IG PEL-N-220-00373-00001 3 3 3 air 0.32 0.15 31 59 with grilles-between-the-glass PEL-N-220-00374-00001 0.33 0.13 26 59 with integral grilles PEL-N-220-00375-00001 0.33 0.13 26 59 1" NaturalSun Low-E IG PEL-N-220-00361-00001 3 3 3 air 0.32 0.31 37 59 with grilles-between-the-glass PEL-N-220-00362-00001 0.33 0.27 32 59 with integral grilles PEL-N-220-00363-00001 0.33 0.27 32 59 R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating Climate Zones (1) Glazing performance values are for configurations with 6 panels or less and calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR values are updated to 2016 (Version 6) criteria. (2) The values shown are based on Canada's updated ENERGY STAR initiative. For center-glass values, see the Product Performance section. See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines. OSBF-6
GRILLE TYPES Typical Grille Profiles Integral Light Technology Putty and Ogee Glaze Grilles Clad Exterior - Wood Interior Putty and Ogee Glaze Grilles Wood Exterior - Wood Interior 5/8" 7/8" 5/8" 7/8" 5/8" 7/8" 5/8" 7/8" 5/8" ILT 7/8" ILT ILT Ogee Glaze Grilles Clad Exterior - Wood Interior 5/8" ILT 7/8" ILT ILT Contoured Aluminum - Grilles-Between-the-Glass 7/8" 2" 3/4" 3/4" 3/4" Contoured GBG 3/4" Contoured GBG 7/8" 2" 7/8" ILT ILT 2" ILT Removable Interior Pine Grilles 3/4" 2" 2" 3/4" Traditional RMB Traditional RMB 2" Traditional RMB Colonial RMB 2" Colonial RMB Interior wood ILT grilles available in Pine, Mahogany or Douglas Fir to match complete unit. Exterior wood ILT grilles available in Pine or Mahogany to match complete unit. OSBF-7
GRILLE TYPES Typical Grille Patterns Integral Light Technology Grilles and Removable Grilles PRAIRIE LITE PATTERNS VG Standard corner lite dimension for patterns = 3-1/2" VG. Integral Light Technology Grilles 9-Lite available in all special sizes. 12-Lite available at 8' height; other heights available per custom drawing. 14-Lite available in units > 2' 1-1/2" width. Removable Grilles 9-Lite available in units < 7' 0-1/2" height. in heights > 7' 0-1/4" will have 12 Lites. OTHER AVAILABLE PATTERNS VG Top Row Standard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller. Cross Standard visible glass to separator bar = one-quarter of total visible glass height. New England Standard visible glass to separator bar = half of total visible glass height. Grilles-Between-the-Glass PRAIRIE LITE PATTERNS VG VG VG (9-Lite) (12-Lite) (12-Lite) (14-Lite) Top Row Cross New England Standard corner lite dimension = 3-1/2" VG. 9-Lite available in units < 7' 0-3/4" height. in heights > 7' 0-1/2" will have 12 lites. 12-Lite available in units 7' 2" height. (9-Lite) (12-Lite) (12-Lite) (14-Lite) OTHER OTHER AVAILABLE AVAILABLE PATTERNS PATTERNS VG Cross Horizontal bar is 1/4 of visible glass from the top in door panels. Not available in transoms. Cross Top Row Top Row Horizontal bar may be ordered 12", 14" or 16" from the top VG. Transoms with frame heights 21", the horizontal bar will be positioned at 1/2 the visible glass height. Top Row not available in transoms with frame height <21". VG = Visible Glass Lite dimensions noted can vary. Custom configurations are available; for details contact your local Pella sales representative. OSBF-8
SIZE DIMENSIONS Panel Configurations Size-Dimensions NUMBER-OF- PANELS ONE-WAY (NO-PASSAGE-DOOR) Min-Frame- Max-Frame- ONE-WAY (PASSAGE-DOOR) Min-Frame- Max-Frame- SPLIT (NO-PASSAGE-DOOR) Min-Frame- Max-Frame- SPLIT (PASSAGE-DOOR) Min-Frame- Max-Frame- 2-PANEL 31-11/16 87-3/16 3-PANEL 46-1/8 129-3/8 46-15/16 130-3/16 4-PANEL 60-9/16 171-9/16 60-5/8 171-5/8 61-3/8 172-3/8 5-PANEL 75 213-3/4 75-13/16 214-9/16 6-PANEL 89-7/16 255-15/16 89-1/2 256 90-1/4 256-3/4 Minimum to Maximum door width dimensions refers to frame to frame dimension. Values represent minimum and maximum values without consideration of panel configuration, consult design data for specific values for your venting configuration. Panel Configurations Two Panel Three Panel Four Panel Five Panel Six Panel 2L 3L 4L 5L 6L 2R 3R 4R 5R 6R 2L-1R 3L-1R 4L-1R 5L-1R 1L-2R 1L-3R 1L-4R 1L-5R 2L-2R 2L-3R 2L-4R 3L-2R 4L-2R 3L-3R "P" indicates Passage Door where applicable. Custom sized panels in 1/8" increments. Doors open to the exterior and are configured from left to right as viewed from the exterior. Tradional panels shown. Contact your local Pella sales representative for more information. OSBF-9
SIZE DIMENSIONS Panel Configurations Size Dimensions NUMBER OF PANELS ONE WAY (NO PASSAGE DOOR) Min Frame Max Frame Minimum to Maximum door width dimensions refers to frame to frame dimension. ONE WAY (PASSAGE DOOR) Min Frame Max Frame SPLIT (NO PASSAGE DOOR) Min Frame Max Frame SPLIT (PASSAGE DOOR) Min Frame Values represent minimum and maximum values without consideration of panel configuration, consult design data for specific values for your venting configuration. Max Frame 7-PANEL 103-7/8 298-1/8 104-11/16 298-15/16 8-PANEL 118-5/16 312 118-3/8 340-3/8 119-1/8 312 9-PANEL 132-3/4 312 133-9/16 312 10-PANEL 147-3/16 312 147-1/4 424-3/4 148 312 Panel Configurations Seven Panel Eight Panel Nine Panel Ten Panel 7L 8L 9L 10L 7R 8R 9R 10R 6L-1R 7L-1R 8L-1R 9L-1R 1L-6R 1L-7R 1L-8R 1L-9R 2L-5R 2L-6R 2L-7R 2L-8R 5L-2R 6L-2R 7L-2R 8L-2R 4L-3R 3L-5R 3L-6R 3L-7R 3L-4R 5L-3R 6L-3R 7L-3R 4L-4R 4L-5R 4L-6R 5L-4R 6L-4R "P" indicates Passage Door where applicable. Custom sized panels in 1/8" increments. Doors open to the exterior and are configured from left to right as viewed from the exterior. Tradional panels shown. Contact your local Pella sales representative for more information. 5L-5R OSBF-10
DESIGN DATA Rough Opening Width (RO) / Daylight Opening Width (DLO) Unit Width Panel Width Unit Width Panel Height Unit Height Rough Opening Height (RO) / Daylight Opening Height (DLO) Unit Height Exterior View ARCHITECT SERIES MIN PANEL MAX PANEL BIFOLD 14-1/4" x 48" 42" x 117-3/8" (362 x 1 219) (1 067 x 2 981) ARCHITECT SERIES MIN FRAME MAX FRAME Interior View KEY FW= Frame Width FH= Frame Height TP= Total # of panels PW= Panel Width PH=Panel Height BIFOLD 31-11/16" x 51-1/2" 312" x 121-1/8" (805 x 1 308) (7 925 x 3 077) ROW= Rough Opening Width DLO=Daylight Opening Width SILL TYPE MIN FRAME HEIGHT MAX FRAME HEIGHT PANEL TO FRAME BY SILL TYPE Standard Sill 51-3/4" 121-1/8" 3-3/4" Low Profile (ADA) 51-1/2" 120-7/8" 3-1/2" Flush Sill 51-1/2" 120-7/8" 3-1/2" ALL BIFOLD FRAME WIDTH Rough Opening Width / DLO Width ONE WAY (NO PASSAGE DOOR) ONE WAY (PASSAGE DOOR) Panel Width (FW-(TP - 1) *.1875-3) / TP (FW-(TP - 1) *.1875-3) / TP FRAME HEIGHT Rough Opening Height / DLO Height SPLIT (NO PASSAGE DOOR) STARTING REFERENCE FW+1 (FW-(TP - 2) *.1875-3.25) / TP STARTING REFERENCE FH +.625 SPLIT (PASSAGE DOOR) (FW-(TP - 2) *.1875-4) / TP Panel Height Standard Sill Panel Height low profile Panel Height Flush Sill FH - 3.75 FH - 3.5 FH - 3.5 Rev. 07/06/2018 Panel projection Panel width - 3" OSBF-11
DESIGN DATA VENT-UNITS Configuration Total- Panels Panel- Left Panel- Right Grade1 Passage- Door Passage- Door- Handing Architect-Series-Frame- (Inches) Performance- Class-and- Min-Frame- Width Max-Frame- Width 0L-2R 2 0 2 R35 No 31-11/16 87-3/16 2L-0R 2 2 0 R35 No 31-11/16 87-3/16 0L-3R 3 0 3 R35 Yes Right 46-1/8 129-3/8 3L-0R 3 3 0 R35 Yes Left 46-1/8 129-3/8 1L-2R 3 1 2 R35 Yes Left 46-15/16 129-3/8 2L-1R 3 2 1 R35 Yes Right 46-15/16 129-3/8 0L-4R 4 0 4 R35 No 60-9/16 171-9/16 4L-0R 4 4 0 R35 No 60-9/16 171-9/16 1L-3R 4 1 3 R35 Yes Left 61-3/8 172-3/8 3L-1R 4 3 1 R35 Yes Right 61-3/8 172-3/8 2L-2R 4 2 2 R35 No 60-5/8 171-5/8 0L-5R 5 0 5 R35 Yes Right 75 213-3/4 5L-0R 5 5 0 R35 Yes Left 75 213-3/4 1L-4R 5 1 4 R35 Yes Left 75-13/16 214-9/16 4L-1R 5 4 1 R35 Yes Right 75-13/16 214-9/16 2L-3R 5 2 3 R35 Yes Right 75-13/16 214-9/16 3L-2R 5 3 2 R35 Yes Left 75-13/16 214-9/16 0L-6R 6 0 6 R35 No 89-7/16 255-15/16 6L-0R 6 6 0 R35 No 89-7/16 255-15/16 1L-5R 6 1 5 R35 Yes Left 90-1/4 256-3/4 5L-1R 6 5 1 R35 Yes Right 90-1/4 256-3/4 2L-4R 6 2 4 R35 No 89-1/2 256 4L-2R 6 4 2 R35 No 89-1/2 256 3L-3R 6 3 3 R35 Yes Option 90-1/4 256-3/4 0L-7R 7 0 7 NC Yes Right 103-7/8 298-1/8 7L-0R 7 7 0 NC Yes Left 103-7/8 298-1/8 1L-6R 7 1 6 NC Yes Left 104-11/16 298-15/16 6L-1R 7 6 1 NC Yes Right 104-11/16 298-15/16 2L-5R 7 2 5 NC Yes Right 104-11/16 298-15/16 5L-2R 7 5 2 NC Yes Left 104-11/16 298-15/16 3L-4R 7 3 4 NC Yes Left 104-11/16 298-15/16 4L-3R 7 4 3 NC Yes Right 104-11/16 298-15/16 0L-8R 8 0 8 NC No 118-5/16 312 8L-0R 8 8 0 NC No 118-5/16 312 1L-7R 8 1 7 NC Yes Left 119-1/8 312 7L-1R 8 7 1 NC Yes Right 119-1/8 312 2L-6R 8 2 6 NC No 118-3/8 312 6L-2R 8 6 2 NC No 118-3/8 312 3L-5R 8 3 5 NC Yes Option 119-1/8 312 5L-3R 8 5 3 NC Yes Option 119-1/8 312 4L-4R 8 4 4 NC No 118-3/8 312 (1) Maximum performance when glazed with the appropriate glass thickness. Those noted as NC are not AAMA/WDMA performance certified. OSBF-12
DESIGN DATA VENT UNITS Configuration 1 Total Panels Panel Left Panel Right Performance Class and Grade1 Passage Door Passage Door Handing Architect Series Frame (Inches) Min Frame Width Max Frame Width 0L-9R 9 0 9 NC Yes Right 132-3/4 312 9L-0R 9 9 0 NC Yes Left 132-3/4 312 1L-8R 9 1 8 NC Yes Left 133-9/16 312 8L-1R 9 8 1 NC Yes Right 133-9/16 312 2L-7R 9 2 7 NC Yes Right 133-9/16 312 7L-2R 9 7 2 NC Yes Left 133-9/16 312 3L-6R 9 3 6 NC yes Left 133-9/16 312 6L-3R 9 6 3 NC Yes Right 133-9/16 312 4L-5R 9 4 5 NC Yes Right 133-9/16 312 5L-4R 9 5 4 NC Yes Left 133-9/16 312 0L-10R 10 0 10 NC No 147-3/16 312 10L-0R 10 10 0 NC No 147-3/16 312 1L-9R 10 1 9 NC Yes Left 148 312 9L-1R 10 9 1 NC Yes Right 148 312 2L-8R 10 2 8 NC No 147-1/4 312 8L-2R 10 8 2 NC No 147-1/4 312 3L-7R 10 3 7 NC Yes Option 148 312 7L-3R 10 7 3 NC Yes Option 148 312 4L-6R 10 4 6 NC No 147-1/4 312 6L-4R 10 6 4 NC No 148 312 5L-5R 10 5 5 NC Yes Option 148 312 (1) Maximum performance when glazed with the appropriate glass thickness. Those noted as NC are not AAMA/WDMA performance certified. OSBF-13
DETAILED PRODUCT DESCRIPTIONS FRAME Interior exposed surfaces are [pine] [mahogany] [douglas fir], edgebanded on straight members. Exterior surfaces are thermally broken clad with aluminum at the head and jambs. Frame depth is 5-7/8" (149 mm). Jamb extensions available to adapt door to wall thickness between 4-9/16" (116mm) to 7" (178mm). Sill is [2-1/8" standard profile] [1/2" low profile] [flush profile]. Material and finish is thermally broken extruded aluminum with Bronze anodized finish. Installation Fin is solid aluminum extruded with exterior head and jamb covers. Frame width greater than 312" (7 925mm)] will receive two (2) pieces for head and two (2) pieces for sill that require splicing during installation. DOOR PANELS Select softwood, immersion treated with Pella s EnduraGuard wood protection formula in accordance with WDMA I.S.-4. The EnduraGuard formula includes three active ingredients for protection against the effects of moisture, decay, stains from mold and mildew. Plus, an additional ingredient adds protection against termite damage. Interior exposed surfaces are veneered with [Pine] [Mahogany] [Douglas Fir] on straight members. Exterior surfaces are clad with aluminum. Panel stiles are LVL core with finger-jointed edge bands on both sides and veneered on both faces. Panel rails are three-ply construction, randomly finger-jointed blocks laminated with waterresistant glue and veneered on both sides. Corners are urethane-silicone hybrid sealed and secured with metal fasteners. Panel thickness is 2-1/16" (52mm). WEATHERSTRIPPING Foam leaf seal along jambs, head and sill on jambs, head and sill of frame. Mohair along the head of frame. Foam leaf seal along the stiles of panel. Bristle rainscreen along bottom of panel. Foam pad between off-set panel hinges. GLAZING SYSTEM 1 Quality fully-tempered float glass complying with ASTM C 1048. Urethane-glazed 13/16" dual-seal insulating glass [clear] [obscure] [[Advanced Low-E with argon] [SunDefense Low-E with argon] [AdvancedComfort Low-E with argon] [NaturalSun Low-E with argon]] [[bronze] [gray] [green] Advanced Low-E with argon]. Custom and high altitude glazing available. or Silicone-glazed 1" triple-pane insulating glass [[annealed][tempered]] [[Advanced Low-E with argon] [Advanced Low-E with krypton] [SunDefense Low-E with argon] [SunDefense Low-E with krypton] [NaturalSun Low-E with argon] [NaturalSun Low-E with krypton]]. EXTERIOR Aluminum-clad exteriors shall be finished with EnduraClad protective finish on panels, in a multi-step, baked-on finish. Aluminum-clad exterior frame shall be finished in accordance with AAMA 2604 standards. Color is [Standard 2] [Custom 2]. or Aluminum-clad exteriors shall be finished with EnduraClad Plus protective finish with 70% fluoropolymer resin on panels, in a multistep, baked-on finish. Aluminum-clad exterior frame shall be finished in accordance with AAMA 2605 standards. Color is [Standard 2] [Custom 2]. INTERIOR Door Panels are [Unfinished, ready for site finishing] [factory primed with one coat acrylic latex] [factory prefinished [White] [Linen White] [Bright White] [stain 2]]. Door Frames and astragals are Unfinished ready for site finishing. HARDWARE Hinges Doors will have three (3) hinges. Passage Door Locks (when applicable) Doors will have one (1) strike at the head and sill; and three (3) locking points. Mortised and keyed multi-point locking system. Standard handle height is 36" from bottom of panel to bottom of escutcheon plate. Solid brass handles and keylock with K keyway pinlock cylinder. Flush Bolts Non-passage door panels will have a flush bolt at both the head and sill on every other panel to lock panel into place. Bottom flush bolt length is approximately 7-1/2"; and Top Flush Bolt length will vary based on the height of the door.. [7-1/2"] [17-3/4"] [23-5/8"] [39-5/8"]. Finish Hardware finish is [Bright Brass] [Oil-Rubbed Bronze] [Satin Nickel]. OPTIONAL PRODUCTS Grilles Integral Light Technology Grilles Interior grilles are [5/8"] [7/8"] [1-1/4"] [2"] ogee profile that are solid [Pine] [mahogany] [douglas fir]. Interior surfaces are [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 1]]. Exterior grilles are [5/8" putty profile] [7/8" [putty] [ogee] profile] [1-1/4" [putty] [ogee] profile] [2" ogee profile] that are extruded aluminum. Patterns are [Traditional] [] [Top Row] [Cross] [New England] [Victorian]. Insulating glass contains non-glare spacer between the panes of glass. Grilles are adhered to both sides of the insulating glass with VHB acrylic adhesive tape and aligned with the non-glare spacer. or Grilles-Between-the-Glass 3 Insulating glass contains 3/4" contoured aluminum grilles permanently installed between two panes of glass. Patterns are [Traditional] [] [Cross] [Top Row] Interior color is [White] [Black] [Tan 4] [Brown 4] [Putty 4] [Ivory] [Brickstone] [Harvest] [Cordovan]. Exterior color 5 is [Standard] 2. or Roomside Removable Grilles [[3/4"] [1-3/4"] [2"] Regular] [[1-1/4"] [2"] Colonial] profile. [Traditional] [] patterns that are removable solid pine wood bars steel-pinned at joints and fitted to sash with steel clips and tacks. Interior [unfinished, ready for site finishing] [factory primed] [pine: factory prefinished [White] [Linen White] [Bright White] [stain 2]]. Exterior [unfinished, ready for site finishing] [primed] [finish color matched to exterior cladding 5]. (1) Insulating glass with argon is Low-E coated. All other insulating glass is air-filled. (2) Contact your local Pella sales representative for current color options. (3) Available in clear, Low-E and obscure insulating glass. (4) Tan, Brown or Putty Interior GBG colors are available in single-tone (Brown/Brown, Tan/Tan or Putty/Putty). Other interior colors are also available with Tan or Brown exterior. (5) Appearance of exterior grille color will vary depending on Low-E coating on glass. OSBF-14
UNIT SECTIONS 6" [153] VH 2" [51] 2 7/8" [73] PH LA ICS OH R1 L3 L2 L1 VH VENT HEAD PH LK HANDLE VSASTR ICS OHHS PH LK: Multipoint Lock PH: Pivot Set ICS: Intermediate Carrier Set ECS: End Carrier Set HHS: Hinge Handle Set OHHS: Offset Hinge Handle Set ASTR: Astragal 1 3/4" [44] PANEL HEIGHT 2 1/16" [52] FRAME HEIGHT 3/4" [19] 10 1/4" [19] LA LOCK HANDLE ASTRAGAL 3/16" [5] [32] 8 3/4" [221] 2 1/16" [52] VS VENT SILL ICS INTERMEDIATE CARRIER SET 9 3/8" [19] 8 3/4" [19] 8 3/4" [222] 2 5/16" [59] OH OFFSET HINGE HANDLE SET 9 3/8" [19] 2 1/8" [54] LV 1/4" [6] LOW PROFILE VENT SILL FS FLUSH SILL Finished Floor Material by Others. 6" [153] 4 11/16" [119] PH PIVOT SET 1 7/8" [47] 3/16" [6] 3/4" [19] Sub Floor 15/16" [24] 1/4" [6] 1 5/16" [33] 6 3/16" [158] 15/16" [24] 7/16" [10] 15/16" [25] 13/16" [20] Scale 3" = 1' 0" All dimensions are approximate. OSBF-15