Hydraulic Mining Excavator RH170B 7,000 mm 2 6,780 mm 22 7,200 mm 2 7 6,0 mm 20 6,70 mm 22 2 7,870 mm 2 2,200 mm 7,60 mm 18 2,60 mm 8 980 mm 6,200 mm 20 4 8,070 mm 26 6 1,200 mm 11 6,600 mm 21 8 RH170B General Data: Operating weight Face Shovel 97 t 48 sht Backhoe 97 t 48 sht Engine output SAE J 199 Caterpillar C2 1,16 kw 2,02 HP Cummins KTA 8C 1,492 kw 2,000 HP Standard bucket capacity Face Shovel (SAE 2:1) 22.0 m 28.8 yd Backhoe (SAE 1:1) 22.0 m 28.8 yd Features: TriPower shovel attachment Independent oil cooling system Spacious walk-through machine house -circuit-hydraulic system Electronic-hydraulic servo control Board Control System (BCS) Torque control in closed-loop swing circuit Automatic central lubrication system Xenon working light
Operating Weight Shovel Standard track pads Operating weight Ground Pressure Further track pads on request Backhoe Standard track pads Operating weight Ground Pressure Further track pads on request 1,200 mm ('11") 97,400 kg (876,1 lb) 2.8 N/cm 2 (4.4 psi) 1,200 mm ('11") 97,000 kg (87,20 lb) 2.8 N/cm 2 (4.4 psi) Electrical System (diesel drive) System voltage 24V Batteries 6 x 244 Ah - 12 V each in series / parallel installation 72 Ah - 24 V in total Working spot lights 8 x high brightness Xenon lights Battery isolation relays Emergency stop switches accessible from ground level, in engine module and in operator s cab Hydraulic Oil Cooling Oil flow of cooling pumps Diesel version 2 x 799 l/min (2 x 211 US gal/min) Electric version 4 x 79 l/min (4 x 0 US gal/min) Diameter of fans 2 x 1,24 mm (2 x 60 ) Cooling system is fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running Gear type cooling pumps supplying high volume low pressure oil to fans and aluminium coolers Variable axial piston pumps supplying low volume high pressure oil to fans Fan speed is thermostatically controlled Extremely high cooling efficiency to ensure optimum oil temperature Electric Motor (optional) Type Squirrel cage induction motor Output 1,400 kw Voltage 6.6 kv ± % (other on request) Rated current I N 14 A Frequency 0 Hz (60 Hz optional) Revolutions 1,00 min -1 (1,800 min -1 optional) Starting current 40% of I N Custom-made electric motor with increased gap between rotor and stator to withstand severe mining conditions Power limit control by Pump Management System Diesel Engines Engine features Hydraulically driven radiator fan with electronically controlled fan speed Microprocessed engine management Automatic rev. reduction Heavy duty air-filters, STRATA 1 with automatic dust evacuation Two-stage fuel filter incl. water separator Additional high capacity water separator Pre-lube starting system (Cummins engines only) Fuel tank capacity 7,800 l (2,060 US gal) Diesel Engines Version 1 - Caterpillar Make and model 2 x Caterpillar C2 Total rated net power ISO 046 / 1 1,16 kw (2,02 HP) 1,70 min -1 Total rated net power SAE J149 1,16 kw (2,02 HP) 1,70 min -1 Total rated gross power SAE J199 1,16 kw (2,02 HP) 1,70 min -1 No. of cylinders (each engine) 12 Bore Stroke Displacement Aspiration Max. altitude without deration 14 mm (.71 in) 162 mm (6.8 in) 2.1 l (1,99 in³) Turbocharged and air to air aftercooled,68 m (12,000 ft) a.s.l. Emission certification US EPA Tier 2 Alternators Version 2 - Cummins 2 x A Make and model 2 x Cummins KTA 8 C-1200 Total rated net power ISO 046 / 1 1,492 kw (2,000 HP) 1,800 min -1 Total rated net power SAE J149 1,492 kw (2,000 HP) 1,800 min -1 Total rated gross power SAE J199 1,492 kw (2,000 HP) 1,800 min -1 No. of cylinders (each engine) 12 Bore Stroke Displacement Aspiration Max. altitude without deration Emission certification Alternators Hydraulic System with PMS 19 mm (6.2 in) 19 mm (6.2 in) 7.8 l (2,00 in³) Turbocharged and aftercooled,600 m (11,800 ft) a.s.l. not available 2 x 17 A Main pumps Diesel version 4 x variable swash plate pumps Electric version 4 x variable flow axial piston pumps Max. oil flow Diesel version 4 x 74 l/min (4 x 196 US gal/min) Electric version 4 x 924 l/min (4 x 244 US gal/min) Max. pressure, attachment 2 MPa = 20 bar (4,640 psi) Max. pressure, travel 6 MPa = 60 bar (,220 psi) Swing pumps Diesel version 4 x reversible swash plate pumps Electric version x reversible swash plate pumps Max. oil flow Diesel version 4 x 26 l/min (4 x 86 US gal/min) Electric version x 487 l/min ( x 129 US gal/min) Max. pressure, swing circuit MPa = 0 bar (,080 psi) Total volume of hydraulic oil Diesel version approx.,400 l (1,40 US gal) Electric version approx. 6,000 l (1,80 US gal) Hydraulic tank capacity Diesel version approx.,000 l (790 US gal) Electric version approx.,600 l (90 US gal) Pump Managing Systems (PMS) contains: Electronic load limit control Flow on demand from main pumps depending on joystick position Automatic regulation of main pumps to zero flow without demand Automatic rpm reduction of engine speed during working breaks Reduced oil flow of main pumps at high hydraulic oil temperature or at high engine temperature Pressure cut-off for main pumps Cooling of pump transmission gear oil Filters: Full-flow high-pressure filters (0 µm) for the main pumps, installed directly behind each pump Full-flow filters ( µm) for the complete return circuit Full-flow filters ( µm) for the cooling return circuit Pressure filters (6 µm) for servo circuit Pressure filters (40 µm) for the feed pumps of the closed swing circuit Transmission oil filters (40 µm) 2 Copyright 2009 Terex Corporation
Undercarriage Travel speeds (2 stages) 1 st stage Max. 1.6 km/h (0.99 mph) 2 nd stage Max. 2.6 km/h (1.62 mph) Max. tractive force: 2,000 kn (204 t = 449,460 lb) Gradability of travel drives Max. % Track pads (each side) 42 Bottom rollers (each side) 7 Support rollers (each side) Travel drives (each side) Parking brakes 2 plus a skid plate in between 1 planetary transmission with 2 two-stage axial piston motors Wet multiple disc brake, spring applied / hydraulically released Cast double-grouser combined pad-links with bushings connected by hardened full floating pins All running surfaces of sprockets, idlers, rollers and pad links as well as teeth contact areas of sprocket and pad links are hardened Fully hydraulic self-adjusting track tensioning system with membrane accumulator Automatic hydraulic retarder valve to prevent over-speed on downhill travel Acoustic travel alarm Operator s Cab Operator s eye level approx. 6.7 m (22'2") Internal dimensions of cab Length 2,200 mm (7'") Width 1,600 mm ('") Height 2, mm (7'1") Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, seat heating, safety belt, head and arm rests Switch in seat cushion to neutralize automatically the hydraulic controls when operator leaves the seat Joystick controls integrated in independently adjustable seat consoles Fold-away auxiliary seat with safety belt FOPS (rock guard; approved acc. to DIN ISO 449) integrated into cab structure All-round safety glass, armoured windshield and sliding side window Windshield with parallel intermittent wiper / washer Roller blind at windshield Robust instrument panel incl. large colored BCS screen with transflective technology Terex Board Control System (BCS) electronic monitoring and data logging system for vital signs and service data of engines, hydraulic and lubrication system Machine access via retractable boarding ladder, hydraulically operated Emergency exit harness kit Attachments Booms and sticks are torsion resistant, welded box design of high tensile steel with massive steel castings at pivot areas Welding procedures allow for internal counter-welding (double prep weld) wherever possible Boom and sticks are stress relieved after welding Inspection hole in monoboom of BH-attachment Catwalks with rails at boom (FS and BH) "Pressure-free lowering" of boom (FS and BH) and stick (FS) by means of a float valve Shovel attachment with Terex patented TriPower kinematics ensuring the following main features: Horizontal automatic constant-angle bucket guidance Vertical automatic constant-angle bucket guidance Automatic roll-back limiter to prevent material spillage Kinematic assistance to hydraulic forces Constant boom momentum throughout the whole lift arc Crowd force assistance All buckets (FS and BH) are equipped with a universal wear wear package suitable for all standard applications, which consists of: Special liner material covering main wear areas inside and outside of bucket Lip shrouds between teeth Wing shrouds on side walls Heel shrouds at bottom edges Special wear packages for highly abrasive materials on request Swing System RH170B Swing drives compact planetary transmissions with axial piston motors Parking brakes Wet multiple disc brake, spring loaded / hydraulically released Max. swing speed Diesel version 4.7 rpm Electric version.1 rpm Swing ring Triple race roller bearing with sealed internal gearing Closed-loop swing circuit with torque control Hydraulic braking of the swing motion by counteracting control All race ways of swing ring as well as grease bath for internal gearing supplied by automatic central lubrication system Automatic Lubrication System Capacity of grease container 1,000 l (264 US gal) Dual-circuit system with hydraulically driven heavyduty pump and electronic time relay control to adjust the pause / lube times Connected to the lubrication system are the swing roller bearing with internal gearing and all pivot points of attachment, bucket and cylinders System failures displayed by Board Control System Grease filters (200 µm) between service station and container as well as directly behind grease pump Retractable Service Station Retractable service station installed underneath the engine module and easily accessible from ground. Equipped with: Quick couplings for Diesel fuel Engine coolant - left / right Pump transmission gear oil - left / right Engine oil (oil pan) - left / right Engine oil (additional tank - optional) - left / right Hydraulic oil tank Grease container CAT jump start socket Indicator lights for fuel tanks left / right full and grease container full Copyright 2009 Terex Corporation
TriPower Face Shovel Attachment (FS) Working Diagram - Boom 7. m (2'11") - Stick 4.6 m (1'1") ft 0 4 40 0 2 20 1 0 m 1 14 1 12 11 9 8 7 6 4 2 1 0 1 2 190 sht 17 16 1 14 1 12 11 9 8 7 6 4 2 1 0 m 0 4 40 0 2 20 1 0 ft Working Range Max. digging height 14.4 m 47'" Max. digging reach 1.4 m 0'6" Max. digging depth 2.6 m 8'6" Max. dumping height.9 m '9" Crowd distance on level.1 m 16'9" Digging Forces Max. crowd force 1,8 kn 406,760 lb Max. crowd force at ground level 1,280 kn 287,60 lb Max. breakout force 1,270 kn 28,4 lb Face Shovels Type Iron ore shovel Heavy rock shovel Heavy rock shovel Standard rock shovel Tooth system ESCO Posilok S1 ESCO Posilok S 1 ESCO Posilok S 1 ESCO Posilok S 1 Capacity SAE / PCSA 1:1 17.1 m³ (22.4 yd³) 20.6 m³ (26.9 yd³) 2.2 m³ (0. yd³) 2. m³ (.1 yd³) Capacity SAE / CECE 2:1 1.0 m³ (19.6 yd³) 18.0 m³ (2. yd³) 20.0 m³ (26.2 yd³) 22.0 m³ (28.8 yd³) Total width 4,220 mm (1'4") 4,220 mm (1'4") 4,680 mm (1'4") 4,680 mm (1'4") Inner width,840 mm (12'7"),840 mm (12'7") 4,00 mm (14'1") 4,00 mm (14'1") Opening width 1,940 mm (6'4") 1,940 mm (6'4") 2,0 mm (6'7") 2,0 mm (6'7") No. of teeth 6 6 Weight incl. universal wear kit,600 kg (74,070 lb) 4,00 (7,620) 6,00 kg (80,00 lb) 7,00 kg (82,20 lb) Max. material density (loose) 2.8 t/m³ (4,720 lb/yd³) 2.2 (,7 lb/yd³) 2.0 t/m³ (,70 lb/yd³) 1.8 t/m³ (,00 lb/yd³) 4 Copyright 2009 Terex Corporation
RH170B Backhoe Attachment (BH) Working Diagram - Boom 9. m (1'2") - Stick 4.6 m (1'1") ft 60 0 4 40 0 2 20 1 0 1 20 2 m 18 17 16 1 14 1 12 11 9 8 7 6 4 2 1 0 1 2 4 6 7 8 190 sht 0 9 20 19 18 17 16 1 14 1 12 11 9 8 7 6 4 2 1 0 m 6 60 0 4 40 0 2 20 1 0 ft Backhoes Type Heavy rock bucket Heavy rock bucket Standard rock bucket Tooth system ESCO Posilok S9 ESCO Posilok S9 ESCO Posilok S9 Capacity 18.0 m³ 20.0 m³ 22.0 m³ SAE 1:1 (2. yd³) (26.2 yd³) (28.8 yd³) Capacity 16.1 m³ 17.7 m³ 19. m³ CECE 2:1 (21.1 yd³) (2.2 yd³) (2. yd³) Capacity 14.0 m³ 1. m³ 17.2 m³ struck (18. yd³) (20.0 yd³) (22. yd³) Total width 4, mm (1'7") 4, mm (1'7") 4, mm (1'7") Inner width,800 mm (12'6"),800 mm (12'6"),800 mm (12'6") No. of teeth 6 6 6 Weight incl. 21,000 kg 22,600 kg 2,800 kg universal wear kit (46,00 lb) (49,820 lb) (2,470 lb) Max. material 2.2 t/m³ 2.0 t/m³ 1.8 t/m³ density (loose) (,7 lb/yd³) (,70 lb/yd³) (,00 lb/yd³) Working Range Max. digging depth 7.0 m 2' Max. digging reach 17.7 m 8'1" Max. digging height 16.8 m '1" Digging Forces Max. crowd force 1,070 kn 240,460 lb Max. breakout force 1,120 kn 21,700 lb Copyright 2009 Terex Corporation
General Packing List Crawler side frame with track pads (2 units) Undercarriage centre frame with swing roller bearing Width 1,800 mm ('11") Gross weight 1,00 kg (11,40 lb) Width,800 mm (12'6") Gross weight,900 kg (74,740 lb) 2,200 mm (7 ) 8,070 mm (26 6 ) 6,240 mm (20 6 ) Superstructure centre frame Engine module with diesel engines Width,6 mm (11'") Gross weight 0,00 kg (111,0 lb) Width 6, mm (20'2") Gross weight C2,000 kg (72,70 lb) Gross weight KTA8,000 kg (77,160 lb),180 mm ( ) 9,00 mm (1 2 ) Cab pedestal module Oil cooler module Width 2,00 mm (6'9") Gross weight,800 kg (12,790 lb) Width 2,000 mm (6'7") Gross weight 7,000 kg (1,40 lb) 4,00 mm (14 9 ) Crate with cabin and FOPS Counterweight incl. radiators Width 2,6 mm (8'7") Gross weight,00 kg (7,720 lb) Width 1,00 mm (4'") Gross weight 8,700 kg (8,20 lb),070 mm ( 1 ),0 mm ( 2 ),600 mm (11 ) 2,120 mm (6 11 ),80 mm (12 8 ) 4,00 mm (14 9 ),00 mm ( ),0 mm ( 2 ),00 mm (11 6 ) 6,0 mm (20 ) Crates Content Length Width Height Gross weight Three swing gear 1,00 mm (4'11") 1,0 mm (4'") 1,90 mm (6'4"),80 kg (8,440 lb) Swing ring cover 2,200 mm (7'") 1,00 mm (4'") 1,000 mm ('") 40 kg (70 lb) Swing ring bolts, ladder, etc,,000 mm (9'") 1,270 mm (4'2") 1,280 mm (4'2") 1,700 kg (,70 lb) Grease container with pump 1,700 mm ('7") 1,00 mm (4'") 2,00 mm (6'9") 1,470 kg (,240 lb) Barrels (hydraulic oil) 2,00 mm (8'2") 1,00 mm (4'") 1,270 mm (4'2") 1,00 kg (, lb) Barrels (engine oil; antifreeze) 2,00 mm (8'2") 1,00 mm (4'") 1,270 mm (4'2") 1,00 kg (, lb) Length Height Above values are approximate. Details may vary depending on scope of supply and destination. Exact data subject to selected machine configuration and final packing list. 6 Copyright 2009 Terex Corporation
RH170B TriPower Shovel Attachment Boom with main valve block, TriPower linkages and rods Stick Width 2,700 mm (9'2") Gross weight,900 kg (79, lb) Width 2,00 mm (6'9") Gross weight 12,660 kg (27,9 lb) Face shovel incl. pin for stick Capacity (2:1) Width Gross weight 22.0 m³ (28.8 yd³) 4,700 mm (1'") 8,00 kg (84,440 lb) 1.0 m³ (19.6 yd³) 4,20 mm (1'11") 4,600 kg (76,280 lb) Crates with catwalks, railings and other parts Length-mm (ft:in) Width-mm (ft:in) Height-mm (ft:in) Gross weight-kg (lb) 4,270 (14') 1,900 (6'") 1,680 ('6") 2,700 (,90),000 (6'") 1,900 (6'") 1,70 ('9") 2,900 (4,60) Length Height Bundle with 2 boom cylinders 2 Bundles with 2 stick cylinders and 2 bucket cylinders, each: Width 1,0 mm ('7") Gross weight 6,700 kg (14,770 lb) Width 1,0 mm ('7") Gross weight 4,00 kg (9,480 lb) Backhoe Attachment Monoboom without main valve block Stick with linkage and bucket cylinders Width 4,60 mm (1'") Gross weight 4,900 kg (76,940 lb) Width 2,200 mm (7'") Gross weight 2,000 kg (0,7 lb) 2,00 mm (7'7") Backhoe bucket incl. pins for stick and linkage Capacity (2:1) Width Gross weight 22 m³ (28.8 yd³) 4, mm (14'2") 24,800 kg (4,670 lb) Crates with main valve block, catwalks, railings and other parts Length-mm (ft:in) Width-mm (ft:in) Height-mm (ft:in) Gross weight-kg (lb) 4,800 (1'9") 2,40 (8'0") 2,000 (6'7"),00 (27,80) 4,960 (16'") 1,900 (6'") 1,780 ('") 2,200 (7,00) 4,160 (1'8") 2,080 (6'") 1,80 (6'1") 2,700 (11,0) Height,00 mm ( ) 2,0 mm (6 11 ) 8,270 mm (27 2 ),0 mm (17 7 ) 22 m³ = 4, mm (1 7 ) 1 m³ = 4,000 mm (1 1 ) 22 m³ =,400 mm (11 2 ) 1 m³ =,0 mm ( 2 ) 0 mm (1 ) 0 mm (1 ) 4,0 mm (14 ) 4,200 mm (1 9 ),0 mm ( 11 ) 2,80 mm (9 4 ) 6,4 mm (21 ) 2,00 mm (8 2 ),200 mm ( 6 ),820 mm (12 6 ) Length Bundle with boom 2 cylinders Bundle with 2 stick cylinders Width 1,200 mm ( 11 ) Gross weight 9,600 kg (21,160 lb) Width 1,200 mm ( 11 ) Gross weight 6,400 kg (14,1 lb) 70 mm (2 6 ) 700 mm (2 4 ),700 mm (18 8 ) 4,800 mm (1 9 ) Above values are approximate. Details may vary depending on scope of supply and destination. Exact data subject to selected machine configuration and final packing list. Copyright 2009 Terex Corporation 7
Component accessibility on superstructure 1. Diesel engines 4. Oil coolers 7. Rotary distributor. Operator s seat 2. Gearboxes with hydraulic pumps. Hydraulic tank 8. Travel valves 11. BCS tower. Engine radiators with hydraulically driven fan 6. Swing drives 9. Switch cabinet and battery box 12. Auxilliary seat 4 4 2 1 8 7 6 9 2 1 11 12 Anti-slip walking areas Anti-slip catwalks Optional Equipment General Export crating Finishing as per enduser s corporate colours Customizing of logos as per customer s specification Superstructure Hydraulic service crane on superstructure with auxilliary engine Mesabi radiators instead of standard radiators (Cummins engines only) Oil change interval extension for engine oil up to 00 hrs (Cummins engines only) Engine oil burn system (Cummins engines only) Centrifuges for engine oil filtration (Cummins engines only) Folding access stairway, stairway angle approx. 4 Round container with a standard 200 l grease barrel (instead of 00 l grease container) Lubricated pinion for greasing of internal gearing of swing ring Various cold weather packages The technical specifications mentioned in this data sheet may vary according to the specific equipment/options installed. Cab Various heating and airconditioning systems Roller blinds at all windows Outside mounted sun shields Additional instrumentation Undercarriage Track pad width 1,400 mm or 1,600 mm Automatic lubrication of rollers by central lube system Cover plate under carbody (belly plate) Attachment Xenon lighting on boom Special wear packages Further optional equipment on request Effective Date: November 2009. Product specifications and prices are subject to change without notice or obligation. The photographs and/ or drawings in this brochure are for illustrative purposes only. Refer to the appropriate Operator s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or tradenames of Terex Corporation and/or its subsidiaries in the USA and other countries and all rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. Copyright 2009 Terex Corporation. M 17. e / 19 Terex GmbH Karl-Funke-Str. 6, D-44149 Dortmund, Germany Tel +49 (0) 21 922 Fax +49 (0) 21 922 800 miningexcavators@terex.com www.terexmining.com