Table Of Contents Terms and Engineering Data...2 Lead-Free Brass Ball Valves...3-4 TFP600-LF Full port, 2-piece body, lead-free, Threaded Ends...3 SFP600-LF Full port, 2-piece body, lead-free, Solder Ends...4 Bronze Butterfly Valves...5-6 BFVA-TB3941 Bronze body, Threaded ends...5 BFVA-GB3941 Bronze body, Grooved ends...6 Ductile Iron Butterfly Valves...7-8 BFVA-GD3851-TM2 Ductile Iron body, Grooved Ends...7 Butterfly Valve Performance Data...8 Ductile Iron Gate Valves...9-10 GTVA-FD3151-HW Ductile Iron body, Resilient Seated OS&Y type, Flanged Ends...9 GTVB-FD3151-HW Ductile Iron body, Resilient Seated N.R.S type, Flanged Ends...10 Ductile Iron Check Valves...11-13 CKVA-GD8351 Ductile Iron body, Grooved ends, Swing Check...11 CKVE-GD8351 Ductile Iron body, Grooved ends, Riser (Shotgun) Check...12 Check Valve Performance Data...13 Grooved Couplings &Fittings...14-22 Std. Weight Rigid Coupling with Pre-lubricated C Gasket - GRCR...14 Std. Weight Flexible Coupling with Pre-lubricated C Gasket - GRCF...14 Reducing Coupling with Pre-lubricated Gasket - GRRC...14 Mechanical Tee, Threaded - GRMT...15 Mechanical Tee, Grooved - GRMG...15 Mechanical Tee, U-Bolted - GRMU...16 Hinge Adapter, Flange- GRFL...16 Flange Adapter, Threaded - GRFT...16 Flange Adapter, Grooved - GRFG...17 Adapter Elbow - GRAE...17 Reducing Adapter Nipple - GRRNP...17 45 Elbow - GRE4...18 90 Elbow, Short Radius - GRES...18 11¼ Elbow, Standard Radius- GRE...18 22½ Elbow, Standard Radius- GRE...18 Cross - GRCS...19 Cap - GRCP...19 Drain Cap - GRDC...19 Tee, Short Radius - GRTS...19 Reducing Tee, Grooved - GRTG...20 Reducing Tee, Threaded - GRT T...20 Concentric Reducer, Threaded - GRRT...21 Concentric Reducer, Grooved - GRRG...21 Grooved Fittings Specification data...22
Terms & Engineering Data BLV: Ball Valve PSI: Pounds Per Square Inch BFV: Butterfl Valve RF. FLG.: Raised Face Flange BRZ.: Bronze SB: Screw-in Bonnet B.W.: Butt-weld SPEC: Specificatio C.I. Cast Iron (Gray Iron) SS.: Stainless Steel COP.: Copper STD: Standard CS.: Carbon Steel S.W. Socket-weld CWP: Cold Working Pressure SWP: Steam Working Pressure D.I.: Ductile Iron Temp: Temperature F: Degree Fahrenheit Thrd: Threaded FF. FLG.: Flat Face Flange UB: Union Bonnet NRS: Non-Rising Stem WOG: Water-Oil-Gas Service OD: Outside Diameter WWP: Water Working Pressure OS&Y: Outside Screw and York Pressure and Temperature Rating ANSI... ASME... API... ASTM... AWWA... CSA... FM... MSS... NACE... NFPA NSF UL... ULC... UPC... American National Standards Institute American Society of Mechanical Engineering American Petroleum Institute American Society for Testing Material American Water Works Association Canadian Standard Association Factory Mutual Fire Insurance Companies Manufacturers Standardization Society of the Valve and Fittings Industry The National Association of Corrosion Engineers National Fire Protection Association NSF/ANSI 61 Standard 61 for Portable Water Service Underwriters Laboratories Inc. Underwriters Laboratories of Canada IAPMO R&T Certificatio Temperature ( F) A105 (A216 WCB Carbon Steel) Working Pressure in PSIG by Class 150 300 600 900 1500 2500 A182 - F316 (A351 CF8M & CF3M Stainless Steel) Temperature Working Pressure in PSIG by Class ( F) 150 300 600 900 1500 2500-20 to 100 285 740 1480 2220 3705 6170 200 260 675 1350 2025 3375 5625 300 230 655 1315 1970 3280 5470 400 200 635 1270 1900 3170 5280 500 170 600 1200 1795 2995 4990 600 140 550 1095 1640 2735 4560 650 125 535 1075 1610 2685 4475 700 110 535 1065 1600 2665 4440 750 95 505 1010 1510 2520 4200 800 80 410 825 1235 2060 3430 850 65 270 535 805 1340 2230 900 50 170 345 515 860 1430 950 35 105 205 310 515 860 1000 20 50 105 155 260 430 Table from ANSI B16.34-20 to 100 275 742 1440 2160 3600 6000 200 240 620 1240 1860 3095 5160 300 215 560 1120 1680 2795 4666 400 195 515 1030 1540 2570 4280 500 170 480 955 1435 2390 3980 600 140 450 905 1355 2255 3760 650 125 445 890 1330 2220 3700 700 110 430 865 1295 2160 3600 750 95 425 845 1270 2110 3520 800 80 415 830 1245 2075 3460 850 65 405 810 1215 2030 3320 900 50 395 790 1180 1970 3280 950 35 385 775 1160 1930 3220 1000 20 365 720 1090 1820 3030 Table from ANSI B16.34 ASTM B62 & B61 Bronze Alloy Pressure Class by Material & End Style ASTM B62 ASTM B61 Temperature ( F) 125 2,3 150 3 200 3 300 3 Temperature 1 ( F) Cast Iron & Ductile Iron Pressure Class by Material & Valve Size Cast Iron Ductile Iron Class 125 Class 250 Class 150 Thread Thread Thread Thread -20 to 100 200 300 400 600 200 185 270 375 560 250 170 240 350 525 300 155 210 325 490 350 140 180 300 450 400 -- -- 275 410 406 125 1 150 1 -- -- 450 120 145 250 375 500 -- -- 225 340 550 -- -- 200 300 Table from MSS SP-80 1. Some Codes (i.e. ASME BPVC, Section 1) limit the rating temperature of indicated material to 406 F 2. Buna-N disc valves limited to 180 F temperature 3. PTFE disc valves limited to 450 F temperature 4. The Pressure & temperature ratings of Solder end valves vary with the solder & the size Note: Neither NCI or its affiliated entities assumes responsibility for the selection, use and maintenance of any product. Responsibility for the selection, use, and maintenance of any listed product remains with the purchaser and end-user. 2-12 14-24 30-48 2-12 14-24 2-12 -20 to 100 200 150 150 500 300 285 150 200 150 -- 500 300 243 200 190 135 115 460 280 235 225 180 130 100 440 270 -- 250 175 125 85 415 260 225 275 170 120 65 395 250 -- 300 165 110 50 375 240 215 325 155 105 355 230 -- 350 150 100 335 220 210 375 145 315 210 -- 400 140 290 200 200 425 130 270 -- 450* 125 250 185 500 170 550 155 600 140 650 125 The temperature shown for the corresponding rating shall be the material temperature of the pressure rating parts. It shall be assumed that the metal temperature will be the temperature of the contained fluid Use of a pressure rating at a metal temperature other than that of the contained flui shall be the responsibility of the user. 1. Buna-N disc vales limited to 180 F or PTFE disc valves limited to 450 F; * Maximum temperature for bronze trim or PTFE 2
Brass Ball Valve CRN TFP600 Series (NPT Ends) Forged Brass Ball Valve Two-Piece Body Full Port Threaded Ends APPLICATIONS Multi-purpose shut-off valve for use in engineered hot and cold water systems, gas applications, compressed air services, and fire protection. MATERIALS AND CONSTRUCTION - Forged brass body and patented "Raised V" end pieces for increased strength - Full port construction for high flow coefficient - Durable chrome-plated brass ball Stem threaded packing nut for easy adjustment Blow out Proof Stem Conforms to MSS SP 110 standards DESIGN CRITERIA cul Approval Trim and Drain (300 PSI) Compressed Gas Shut off Valves (600 PSI) Flammable Liquid Shut off Valves (600 PSI) Gas Shut off Valves (600 PSI) LP Gas Shut off Valves (600 PSI) Manual Valves (600 PSI) FM Approval - 600 PSI Rating NSF 61 Approval Obtained NSF61 Section 8 certificate through IAPMO Compliant to Prop65 standard CSA Approval (Threaded only) CAN/CGAC 3.16 (1/2 through 2 ) 125 psig AGA3-88 / CGA CR91-002 (1/4 through 2 ) 5 psig UL Listed Subject 258 for Trim and Drain (1/4 through 2 ) 150 WSP - Pilot Adjustable National Standard of Canada. Class 3371-08 Requirement Can1-91 - Gas Lever Non Lubricated Shut-off Valve. Class 3371-10 Requirement CGA-3.16 - Manual Gas Valves on Piping Systems. Class 3371 12. Requirement CGA CR 9102 General Gas Valve US Standard. Class 3371 88. Requirement ANSI Z21.15 Gas Manual Valve House Piping System. Class 3371.92. Requirement IAS US Regulations 3.88 - Manual Gas Valve Metallic in Piping System US Standards. Class 3371-94 Requirements ANSI/ASME B16.33. -20/150F T-FP600: 2-PIECE, FULL PORT, FORGED BRASS BALL VALVE T FP600 Threaded End (IPS) 1/4" through 2" 600 CWP 2½" through 4" 400 CWP Size (IN) L D H W 1/4" 3.23 0.37 1.37 1.81 3/8" 3.23 0.37 1.37 1.81 1/2" 3.23 0.50 1.45 2.12 3/4" 3.94 0.75 1.78 2.41 1" 4.72 0.98 2.29 2.96 1 1/4" 4.72 1.22 2.44 3.28 1 1/2" 7.09 1.50 3.00 3.67 2" 7.09 1.97 3.30 4.21 2 1/2" 8.66 2.50 4.59 5.38 3" 8.66 3.00 4.92 6.06 4" 9.84 3.98 5.73 7.39 1 2 3 4 5 6 7 8 9 10 PART BODY END CAP BALL SEAT STEM THRUST WASHER STEM PACKING GLAND HANDLE NUT MATERIALS LIST SPECIFICATION FORGED BRASS ASTM B124 C37700 FORGED BRASS ASTM B124 C37700 COPPER ALLOY, CHROME PLATED PTFE COPPER ALLOY PTFE PTFE COPPER ALLOY CARBON STEEL PLATED CARBON STEEL PLATED ** OPTIONAL LOCKING LEVER HANDLE, STEM EXTENSION & MEMORY STOP** Above port dimensions meet or exceed full MSS SP-110 standards. 3
Lead-Free Brass Ball Valve CRN TFP600-LF Series (NPT Ends, Lead-Free) Forged Brass Ball Valve Two-Piece Body Full Port Threaded Ends Lead-Free APPLICATIONS Multi-purpose shut-off valve for use in hot and cold portable water systems. MATERIALS AND CONSTRUCTION - Forged brass body and patented "Raised V" end pieces for increased strength - Full port construction for high flow coefficient - Durable chrome-plated lead-free brass ball Stem threaded packing nut for easy adjustment Blow out Proof Stem Conforms to MSS SP 110 standards DESIGN CRITERIA cul Approval Trim and Drain (300 PSI) Compressed Gas Shut off Valves (300 PSI) Flammable Liquid Shut off Valves (300 PSI) Gas Shut off Valves (300 PSI) LP Gas Shut off Valves (300 PSI) Manual Valves (300 PSI) FM Approval - 600 PSI Rating NSF/ANSI 61 (ANNEX G), NSF/ANSI 372 Approval - Obtained NSF61 Section 8 certificate through IAPMO - Compliant to Prop65 standard CSA Approval (Threaded only) - Pilot Adjustable National Standard of Canada. Class 3371-08 Requirement Can1-91 - Gas Lever Non Lubricated Shut-off Valve. Class 3371-10 Requirement CGA-3.16 - Manual Gas Valves on Piping Systems. Class 3371 12. Requirement CGA CR 9102 General Gas Valve US Standard. Class 3371 88. Requirement ANSI Z21.15 Gas Manual Valve House Piping System. Class 3371.92 Requirement IAS US Regulations 3.88 - Manual Gas Valve Metallic in Piping System US Standards. Class 3371-94 Requirements ANSI/ASME B16.33. -20/150F Size (IN) L D H W 1/4" 3.23 0.37 1.37 1.81 3/8" 3.23 0.37 1.37 1.81 1/2" 3.23 0.50 1.45 2.12 3/4" 3.94 0.75 1.78 2.41 1" 4.72 0.98 2.29 2.96 1 1/4" 4.72 1.22 2.44 3.28 1 1/2" 7.09 1.50 3.00 3.67 2" 7.09 1.97 3.30 4.21 T-FP600-LF: 2-PIECE, FULL PORT, LEAD-FREE FORGED BRASS BALL VALVE T FP600-LF Threaded End (IPS) 1/4" through 2" 600 CWP 1 2 3 45 BODY END CAP BALL SEAT STEM PART 6 THRUST WASHER 7 STEM PACKING 8 GLAND 9 HANDLE 10 NUT MATERIALS LIST SPECIFICATION LEAD-FREE BRASS LEAD-FREE BRASS LEAD-FREE BRASS, CHROME PLATED PTFE COPPER ALLOY PTFE PTFE COPPER ALLOY CARBON STEEL PLATED CARBON STEEL PLATED Above port dimensions meet or exceed full MSS SP-110 standards. 4
Bronze Butterfly Valve - 300 PSI CWP BFVA-TB3941 Bronze Butterfly Valve (Threaded Ends) 300 PSI Non-shock Cold Working Pressure Viton Seat, Stainless Steel Disc Mounting Pad ISO 5211/ EN12116 Full Port Patented FM & UL/ULC Listed MATERIALS LIST NO. PART NAME MATERIAL QTY 1 BODY BRONZE C83600 1 2 DISC SS-304 2 3 HANDWHEEL ASTM A216 WCB 1 4 SEAT ASTM D200 VITON 1 5 INDICATOR POWDER METAL 1 6 HOUSING FORGED BRASS 1 7 COVER FORGED BRASS 1 Dimensions (mm) EN12116 Size H ± 3 A ± 1 L M ISO 5211. 1 '' 129 54.0 39.7 44.5 F04/F05 1-1/4'' 137.9 66.7 49.2 55.0 F04/F05 1-1/2'' 145.9 73.0 55.6 60.3 F04/F05 2'' 159.8 82.6 70.0 79.0 F04/F05 2-1/2'' 175.5 114.0 86.5 96.0 F04/F05 For the 1'' sizing: UL listed and FM approved only 5
Bronze Butterfly Valve - 300 PSI CWP BFVA-GB3941 Bronze Butterfly Valve (Grooved Ends) 300 PSI Non-shock Cold Working Pressure Viton Seat, Stainless Steel Disc Mounting Pad ISO 5211/ EN12116 Cut Groove Dimension to AWWA C606-06 Full Port Patented FM & UL/ULC Listed MATERIALS LIST NO. PART NAME MATERIAL QTY 1 BODY BRONZE C83600 1 2 DISC SS-304 2 3 HANDWHEEL ASTM A216 WCB 1 4 SEAT ASTM D200 VITON 1 5 INDICATOR POWDER METAL 1 6 HOUSING FORGED BRASS 1 7 COVER FORGED BRASS 1 Dimensions (mm) Size H ± 3 A ± 1 L M P ± 0.76 O ± 0.76 EN12116 ISO 5211 1-1/4'' 138.9 98.0 42.4 ± 0.41 15.88 7.95 F04/F05 1-1/2'' 145.9 102.0 48.3 ± 0.48 15.88 7.95 F04/F05 2'' 159 104.0 60.3 ± 0.61 15.88 7.95 F04/F05 2-1/2'' 175.5 114.0 73.0 ± 0.74 15.88 7.95 F04/F05 6
Ductile Iron Butterfly Valve - 300 PSI CWP BFVA-GD3851-TM2 Grooved-End Butterfly Valve 300 PSI Non-shock Cold Working Pressure Approved Gear Operator for both Indoor or Outdoor use NSF Certified Polyamide Coated Ductile Iron body for Excellent Protection EPDM encapsulated Disc with Outstanding Flow Characteristics Low Torque Operation Options of Double Internal Supervisory Switches FM & UL/ULC Listed Dimensions 7
Ductile Iron Butterfly Valve - 300 PSI CWP Butterfly Valve Performance Data Formulas for C V Values Where: Q Flow rate (gallons per minute: GPM ΔP = Pressure drop across valve (PSI) C V = Flow coefficient Nominal Pipe Cv Nominal Pipe Cv Nominal Pipe Cv Size O.D. (Full Size O.D. (Full Size O.D. (Full In. mm Mm Open) In. mm mm Open) In. mm mm Open) 2 1/2 65 73.0 221 5 125 141.3 1200 8 200 219.1 3874 3 80 88.9 324 6 150 168.3 1934 10 250 273.0 5995 4 100 114.3 670 PRESSURE DROP P.S.I. FLOW RATE G.P.M. 8
Ductile Iron Gate Valve - 300 PSI CWP GTVA-FD3151-HW Resilient Seated OS&Y Type-Flanged Ends Working Pressure 300 PSI Non-shock Cold Working Pressure Flanged Ends ANSI B16.1 Class 125 Valve Standard Conforms to AWWA C515 FM & UL/ULC Listed Dimensions 9
Ductile Iron Gate Valve - 300 PSI CWP GTVB-FD3151-SN Resilient Seated NRS Type-Flanged Ends Working Pressure 300 PSI Non-shock Cold Working Pressure Flanged Ends ANSI B16.1 Class 125 Valve Standard Conforms to AWWA C515 FM & UL/ULC Listed *Smaller size* 2''- 4'' *Larger size shown* 5'' - 12'' Dimensions 10
Ductile Iron Check Valve - 350 PSI CWP CKVA-GD8351 Grooved-End Swing Check Valve 350 PSI Non-Shock Cold Working Pressure Installed in both Horizontal or Vertical Line with Upward Flow Easier and Faster to Maintain and Install Low Pressure Drop EPDM non-stick leak tight sealing All Stainless Steel Wetted Parts to Provide Superior Corrosion Resistance FM Approved & UL/ULC Listed Dimensions 11
Ductile Iron Check Valve - 350 PSI CWP CKVE-GD8351 Grooved-End Riser (Shotgun) Check Valve 350 PSI Non-Shock Cold Working Pressure Installed in both Horizontal or Vertical Line with Upward Flow Easier and Faster to Maintain and Install Low Pressure Drop EPDM non-stick leak tight sealing All Stainless Steel Wetted Parts to Provide Superior Corrosion Resistance FM Approved & UL/ULC Listed Dimensions 12
Ductile Iron Check Valve - 350 PSI CWP Check Valve Performance Data Formulas for CV Values Where: Q Flow rate (gallons per minute: GPM ΔP = Pressure drop across valve (PSI) C V = Flow coefficient Nominal Pipe Cv Nominal Pipe Cv Nominal Pipe Cv Size O.D. (Full Size O.D. (Full Size O.D. (Full In. mm mm Open) In. mm mm Open) In. mm mm Open) 2 50 60.3 100 4 100 114.3 390 6 150 168.3 1000 2 1/2 65 73 140 5 125 141.3 700 8 200 219.1 1800 3 80 88.9 250 13
Grooved Couplings & Fittings Std. Weight Rigid Coupling with Pre-lubricated C Gasket - GRCR Std. Weight Flexible Coupling with Pre-lubricated C Gasket - GRCF Reducing Coupling with Pre-lubricated Gasket - GRRC 14
Grooved Couplings & Fittings Mechanical Tee, Threaded - GRMT Mechanical Tee, Grooved - GRMG 15
Grooved Couplings & Fittings Mechanical Tee, U-Bolted - GRMU Hinge Adapter, Flange- GRFL Flange Adapter, Threaded - GRFT 16
Grooved Couplings & Fittings Flange Adapter, Grooved - GRFG Adapter Elbow - GRAE Reducing Adapter Nipple - GRRNP 17
Grooved Couplings & Fittings 45 Elbow - GRE4 90 Elbow, Short Radius - GRES 11¼ Elbow,Standard Radius- GRE 22½ Elbow,Standard Radius- GRE 18
Grooved Couplings & Fittings Cross - GRCS Cap - GRCP Drain Cap - GRDC Tee, Short Radius - GRTS 19
Grooved Couplings & Fittings Reducing Tee, Grooved - GRTG Reducing Tee, Threaded - GRTT 20
Grooved Couplings & Fittings 21
Grooved Couplings & Fittings Specifications: All listed fittings and couplings are UL/ULC listed and FM approved for both wet and dry automatic sprinkler systems. ISO 9001 Manufacturing facility. Ductile iron housings conform to ASTM A-536. Pre-lubricated Grade E gasket (EPDM) are standard for all gasketed fittings and couplings. Gasket option: Electroplated, oval neck track head bolts conforms to ASTM-A183 with minimum tensile strength of 110,000psi. Orange paint coatings are in regular stock; Dacromet, Galvanized and Epoxy coatings available upon special request. Product weights are approximate and subject to change. NCI keeps the right to update the product design and specification without notice. Please visit for the most up to date product information. *** Specifications shown are subject to change without notice. *** 22
QUALITY PRODUCTS BY NCI CANADA INDUSTRIAL VALVES Brass and Bronze Ball Valves High Performance Carbon/Stainless Steel Ball Valves Bronze & Iron Gate, Globe and Check Valves Cast & Forged Steel Gate, Globe and Check Valves Butterfly Valves Fire Protection Valves Bronze, Iron and Steel Strainers GROOVED FITTINGS Flexible & Rigid Couplings Reducing Couplings Hinged Flange Adapters Standard Radius Fittings & Flange Adapters Short Radius 90s & Tees Standard Radius 90s & Tees Mechanical Tees U-Bolt Strap Tees Concentric Reducers FIRE PROTECTION VALVES ACR Copper Fittings Copper Press System Fittings & Valves Threaded Bronze Fittings Brass Nipples H.P. Sch 40/80/XXH Seamless Steel Nipples H.P. Sch 40 Welded Steel Nipples PLASTIC FITTINGS ABS-DWV Fittings CPVC-CTS FGG PVF PVC Sch40 White Fittings & Valves METAL FITTINGS ACR Copper Fittings Copper Press System Fittings & Valves Threaded Bronze Fittings Brass Nipples H.P. Sch 40/80/XXH Seamless Steel Nipples H.P. Sch 40 Welded Steel Nipples THERMOPLASTIC (CHEMTROL PVF) PVC Sch80 Valves & Fittings CPVC Sch80 Pipe, Valves & Fittings PP Sch80 (Black & Natural) PVF PVDF Sch80 (Red & Natural) PVF PLUMBING VALVES Gas Ball Valves Boiler Drain Valves Stop and Waste Valves INSULATION Pipe Insulation (Ontario, Québec, Atlantic) Headquarter and East Region Warehouse: 2305 Wyecroft Rd. Oakville, Ontario, L6L 6R2 West Region Warehouse: 7136-56 Ave NW, Edmonton, Alberta, T6B 3L2 Tel: 905-727-5545 / 1-800-268-3509 Fax: 905-727-4088