1. READ THE INSTRUCTION BOOK THOROUGHLY before attempting to operate or carry out any maintenance on the machine. If you do not understand any part of this manual, ask your dealer for assistance. 2. ALWAYS CARRY OUT SAFE MAINTENANCE. Never clean, adjust or maintain the machine until the engine has been stopped, the machine come to rest, the PTO disengaged and the key removed. 3. NEVER WORK UNDER A MACHINE RAISED ON THE 3-POINT LINKAGE unless it is securely supported. 4. NEVER OPERATE THE MACHINE WITH ANY PARTS OR GUARDS MISSING. Check that all guards including the PTO shaft guards are in good condition and in place before operating the machine. 5 OPERATE SAFELY. Before starting work, check that there are no persons or animals in the immediate vicinity of the machine or tractor. Always maintain full control of the tractor and machine. Ensure that you know how to stop the tractor and machine quickly in case of emergency. SAFETY FIRST! 6. SECURE THE PTO GUARD BY MEANS OF CHECK CHAINS to suitable points on the tractor and machine to prevent the outer plastic shield from rotating. 7. NEVER STAND BETWEEN THE MACHINE AND THE TRACTOR WHEELS. 8. DO NOT WEAR LOOSE OR RAGGED CLOTHING 9. BEWARE OF DUST. Under dusty conditions, keep the cab windows and doors closed. The use of a dust mask conforming to EN149 is strongly recommended. 10. BEWARE OF HIGH NOISE LEVELS. Some tractor/implement combinations give noise levels in excess of 90dB at the operator's ear. Under such circumstances, ear defenders should be worn. Keep cab windows and doors closed to reduce noise level. Throughout this handbook, the term `tractor' is used to refer to the power source used to drive the machine. It does not necessarily refer to a conventional agricultural tractor. HEALTH AND SAFETY AT WORK Our equipment is designed so as to conform with current Health & Safety Regulations and therefore poses no significant hazard to health when properly used. Nevertheless, in the interests of all concerned, it is essential that equipment of our manufacture is used in accordance with the instructions that are supplied or are available from our Technical Staff. Legislation requires that all operators are instructed in the safe operation, cleaning and maintenance of equipment and machines. This handbook forms part of that instruction and it must be read and understood before fitting the machine onto the tractor or attempting to use it. Your supplier is responsible for carrying out any necessary pre-delivery inspection, fitting the machine onto the tractor and test running. The supplier must also give instruction in the safe use, maintenance and adjustment of the machine. In the interests of safety, please ensure that the instructions referred to above are brought to the attention of all your employees who are to use the equipment. We recommend that the use of this equipment is restricted to capable trained operatives. Persons under the age of sixteen should not operate the machine and should be kept away from where it is being used. WARRANTY The standard warranty is for 12 calendar months against faulty materials and workmanship. Components supplied as part of the original machine, but manufactured by another company, e.g. PTO shafts, wheels etc., are subject to the original manufacturer's conditions and warranty. Where repairs are carried out under warranty:- a) Claims for the fitting of non original parts will not be considered unless prior agreement has been obtained. b) The repairer must be advised that the work is to be the subject of a warranty claim beforehand. c) Any claim must be submitted within four weeks of the repair. d) The damaged parts must be retained for inspection and returned carriage paid if required. The right to withdraw warranty is reserved if:- a) Non-original parts are fitted. b) The machine has been abused, badly maintained or used for purposes other than that for which it was designed.
INDEX INSTURCTIONS PARTS LISTS Page Instructions 1 Comer discharge rotor gearbox with side output shaft from December 2012 2 Comer discharge rotor gearbox with side output shaft from March 2008 4 Comer discharge rotor gearbox with side output shaft from November 2000 6 Bed chain gearbox - Tomahawk 1005 and 1010 models 8 Bed chain gearbox - Tomahawk 9090 models 9 Comer discharge rotor gearbox 10 BIMA discharge rotor gearbox with side output shaft 11 Comer discharge rotor gearbox with extended input shaft 12 BIMA discharge rotor gearbox with extended input shaft 13 Comer cross beater gearbox 14 COMER (EG Transmissions) PTO shaft - 808 models 15 COMER PTO shaft - 808 models 16 COMER (EG Transmissions) PTO shaft 17 COMER PTO shaft - Combined slip and overrun clutch 18 COMER PTO shaft Wide angle C.V. joint 19 EG Transmissions PTO shaft Wide angle C.V. joint 20 Notes 21 INSTURCTIONS After 50 hours of use the gearbox oil should be drained and replaced with new oil. To drain the oil, remove the valve guard, remove the drain and filler plugs and allow it to empty. Waste oil should be collected and disposed of at an oil recycling facility. Refill the gearbox with SAE90.EP gearbox oil. 1
COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from December 2012. To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 2
Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC4100 1 1 Casing SC3645 1 2 90 elbow SC3282 1 3 Breather SC3288 1 4 Cover SC3635 1 5 Bolt FAS9626 1 6 Washer 8.5 x 25 x 2.5 FAS2343 1 7 Lever SC3636 1 8 Gear 36 tooth SC3272 1 9 Key 14 x 9 x 25 FAS8127 1 10 Bearing 6212 BRG1019 2 11 Int. spring ring FAS7303 1 12 Double lip seal 60 x 80 x 10 BRG3054 1 13 Key 18 x 11 x 70 FAS8128 1 14 Output shaft SC3637 1 15 Cap 22 x 4 SC3638 1 16 Int. spring ring FAS7108 4 17 Cap 80 x 10 AT1559 3 18 Taper roller bearing 32208 BRG1226 2 19 Gear 32 tooth SC3275 1 20 Spacer SC3276 1 21 Lay shaft SC3277 1 22 Shim 79.9 SC3886 3 23 Cap 100 x 10 SC3644 1 24 Taper roller bearing 30208 BRG1222 2 25 Spacer 40.5 x 63.5 x 5 SC3639 1 26 Gear 26 tooth SC3278 1 27 Shim 43.6 x 1.0 SC3640 3 28 Cap 110 x 10 SC3641 1 29 Crown wheel SC3642 1 30 Plug ½ FAS1404 2 31 Double lip seal 40 x 80 x 10 BRG3051 1 32 Input shaft SC3643 1 33 Level Plug SC3662 1 34 Gear 23 tooth SC3280 1 35 Ext. spring ring FAS7017 1 36 Gear 26 tooth SC3273 1 37 M10 x 16 H.T. bolt FAS2650 8 38 Int. spring ring FAS7304 2 39 O-ring OR-3062 HYD4040 1 40 Spacer 82 x 89.6 x 5 SC3646 1 41 Pivot SC3647 1 42 Shim 32.0 SC3648 1 43 Ball 7 / 16 11.1mm SC3649 1 44 Spring SC3650 1 45 Ext. spring ring FAS7180 1 46 Shim 25.6 x 2.5 SC3651 1 47 Pad SC3652 1 48 Copper washer SC3653 1 49 Plug 3 / 8 HYD1403 1 50 Bonded seal HYD4202 1 51 M16 x 25mm H.T. bolt FAS9700 1 52 Taper roller bearing 30308 BRG1227 1 53 Shim 89.7 x 2 SC3654 1 54 Int. spring ring FAS7306 1 55 Shim 51.5 SC3655 2 56 Shim 40.3 x 2.5 SC3656 1 57 Pinion shaft 6 spline SC3887 1 58 Ext. spring ring FAS7307 1 59 Double lip seal 40 x 90 x 8.7 BRG3060 1 60 Shim 71.7 x 1.0 SC3658 1 60 Shim 89.7 SC3888 1 61 Taper roller bearing 30308 BRG1227 1 Oil capacity 5 litres SAE90.EP 3
COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from March 2008 until December 2012. To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 4
Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC4100 1 1 Casing SC3645 1 2 90 elbow SC3282 1 3 Breather SC3288 1 4 Cover SC3635 1 5 Bolt FAS9626 1 6 Washer 8.5 x 25 x 2.5 FAS2343 1 7 Lever SC3636 1 8 Gear 36 tooth SC3272 1 9 Key 14 x 9 x 25 FAS8127 1 10 Bearing 6212 BRG1019 2 11 Int. spring ring FAS7303 1 12 Double lip seal 60 x 80 x 10 BRG3054 1 13 Key 18 x 11 x 70 FAS8128 1 14 Output shaft SC3637 1 15 Cap 22 x 4 SC3638 1 16 Int. spring ring FAS7108 4 17 Cap 80 x 10 AT1559 3 18 Taper roller bearing 32208 BRG1226 2 19 Gear 32 tooth SC3275 1 20 Spacer SC3276 1 21 Lay shaft SC3277 1 22 Shim set 79.9 SC3886 3 23 Int. spring ring FAS7304 2 24 Taper roller bearing 30208 BRG1222 2 25 Spacer 40.5 x 63.5 x 5 SC3639 1 26 Gear 26 tooth SC3278 1 27 Shim 43.6 x 1.0 SC3640 3 28 Cap 110 x 10 SC3641 1 29 Crown wheel SC3642 1 30 Plug ½ FAS1404 2 31 Double lip seal 40 x 80 x 10 BRG3051 1 32 Input shaft SC3643 1 33 Level Plug SC3662 1 34 Gear 23 tooth SC3280 1 35 Ext. spring ring FAS7017 1 36 Gear 26 tooth SC3273 1 37 M10 x 16 H.T. bolt FAS2650 8 38 Cap 100 x 10 SC3644 1 39 O-ring OR-3062 HYD4040 1 40 Spacer 82 x 89.6 x 5 SC3646 1 41 Pivot SC3647 1 42 Shim 32.0 SC3648 1 43 Ball 7 / 16 11.1mm SC3649 1 44 Spring SC3650 1 45 Ext. spring ring FAS7180 1 46 Shim 25.6 x 2.5 SC3651 1 47 Pad SC3652 1 48 Copper washer SC3653 1 49 Plug 3 / 8 HYD1403 1 50 Bonded seal HYD4202 1 51 M16 x 25mm H.T. bolt FAS9700 1 52 Taper roller bearing 30308 BRG1227 1 53 Shim 89.7 x 2 SC3654 1 54 Int. spring ring FAS7306 1 55 Shim 51.5 SC3655 2 56 Shim 40.3 x 2.5 SC3656 1 57 Pinion shaft 6 spline SC3887 1 58 Ext. spring ring FAS7307 1 59 Double lip seal 40 x 90 x 8.7 BRG3060 1 60 Shim 71.7 x 1.0 SC3658 1 60 Shim 89.7 SC3888 1 61 Taper roller bearing 30308 BRG1227 1 Oil capacity 5 litres SAE90.EP 5
COMER DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT SHAFT Used on all Tomahawk models with gearboxes made from November 2000 until March 2008. To identify the date of gearbox manufacture, refer to the date stamp on the gearbox makers identification plate. The month of production is represented by the corresponding letter, A being January, D being April. The two numbers that follow indicate the year. 6
Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC4100 1 1 Casing SC3645 1 2 90 elbow SC3282 1 3 Breather SC3288 1 4 Cover SC3635 1 5 Bolt FAS9626 1 6 Washer 8.5 x 25 x 2.5 FAS2343 1 7 Lever SC3636 1 8 Gear 36 tooth SC3272 1 9 Key 14 x 9 x 25 FAS8127 1 10 Bearing 6212 BRG1019 2 11 Int. spring ring FAS7303 1 12 Double lip seal 60 x 80 x 10 BRG3054 1 13 Key 18 x 11 x 70 FAS8128 1 14 Output shaft SC3637 1 15 Cap 22 x 4 SC3638 1 16 Int. spring ring FAS7108 4 17 Cap 80 x 10 AT1559 3 18 Taper roller bearing 32208 BRG1226 2 19 Gear 32 tooth SC3275 1 20 Spacer SC3276 1 21 Lay shaft SC3277 1 22 Shim set 79.7 SC3279 3 23 Int. spring ring FAS7304 2 24 Taper roller bearing 30208 BRG1222 2 25 Spacer 40.5 x 63.5 x 5 SC3639 1 26 Gear 26 tooth SC3278 1 27 Shim 43.6 x 1.0 SC3640 3 28 Cap 110 x 10 SC3641 1 29 Crown wheel SC3642 1 30 Plug ½ FAS1404 2 31 Double lip seal 40 x 80 x 10 BRG3051 1 32 Input shaft SC3643 1 33 Level Plug SC3662 1 34 Gear 23 tooth SC3280 1 35 Ext. spring ring FAS7017 1 36 Gear 26 tooth SC3273 1 37 M10 x 16 H.T. bolt FAS2650 8 38 Cap 100 x 10 SC3644 1 39 O-ring OR-3062 HYD4040 1 40 Spacer 82 x 89.6 x 5 SC3646 1 41 Pivot SC3647 1 42 Shim 32.0 SC3648 1 43 Ball 7 / 16 11.1mm SC3649 1 44 Spring SC3650 1 45 Ext. spring ring FAS7305 1 46 Shim 25.6 x 2.5 SC3651 1 47 Pad SC3652 1 48 Copper washer SC3653 1 49 Plug 3 / 8 HYD1403 1 50 Bonded seal HYD4202 1 51 M16 x 25mm H.T. bolt FAS9700 1 52 Taper roller bearing 30308 BRG1227 2 53 Shim 89.7 x 2 SC3654 1 54 Int. spring ring FAS7306 1 55 Shim 51.5 SC3655 2 56 Shim 40.3 x 2.5 SC3656 1 57 Pinion shaft SC3657 1 58 Ext. spring ring FAS7307 1 59 Double lip seal 40 x 90 x 8.7 BRG3060 1 60 Shim 71.7 x 1.0 SC3658 1 Oil capacity 5 litres SAE90.EP 7
BED CHAIN GEARBOX Used on Tomahawk 1005 and 1010 models Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC4875 1 1 Casing RT190 SC4971 1 2 Bearing 6013 BRG1078 2 3 Oil seal 65 x 100 x 10 BRG3081 2 4 Shaft - 45mm SC4972 1 5 Circlip internal 62 FAS7107 2 6 Cap seal BRG3504 2 7 Pinion shaft straight tooth SC4973 1 8 Pinion bevel tooth SC4974 1 9 Bearing 6010 BRG1068 1 10 Circlip - internal 80 FAS7108 1 11 Circlip - external 50 FAS7010 1 12 Gear SC4975 1 13 Circlip - external 72 FAS7027 1 14 Circlip - internal 100 FAS7118 2 15 Crown wheel SC4976 1 16 Bearing 6305 BRG1008 2 17 Key 8 x 7 x 30 FAS8134 1 18 Setscrew M8 x 16 FAS2625 6 19 Cover plate SC4977 1 20 Cover plate gasket SC4978 1 21 Sight glass SC3836 2 22 Plug HYD1458 1 Oil capacity 2.5 litres SAE90.EP 8
BED CHAIN GEARBOX Used on Tomahawk 9090 models from serial number 1501 Ref Description Part No. Q ty Ref Description Part No. Q ty Gearbox complete SC3800 1 1 Casing SC3827 1 2 Bearing 6012 BRG1069 2 3 Oil seal 60 x 95 x 10 BRG3059 2 4 Shaft SC3828 1 5 Circlip internal 62 FAS7107 2 6 Cap seal SC3829 2 7 Pinion straight tooth SC3830 1 8 Pinion bevel tooth SC3831 1 9 Bearing 6010 BRG1068 1 10 Circlip - internal 80 FAS7108 1 11 Circlip - external 50 FAS7010 1 12 Gear SC3832 1 13 Circlip - external 65 FAS7007 1 14 Circlip - internal 95 FAS7117 2 15 Crown wheel SC3833 1 16 Bearing 6305 BRG1008 2 17 Key 8 x 7 x 30 FAS8134 1 18 Setscrew M8 x 16 FAS2625 6 19 Cover SC3834 1 20 Gasket SC3835 1 21 Sight glass SC3836 1 22 Plug HYD1458 1 Oil capacity 2 litres SAE90.EP 9
COMER DISCHARGE ROTOR GEARBOX Used on Tomahawk 808 models from serial number 1500 with hydraulically driven cross beater Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Casing SC3270 1 2 Bearing 6212 BRG1019 2 3 Spacer SC3959 1 4 Gear 26 tooth SC3273 1 5 Output shaft SC3274 1 6 Double lip seal 60 x 80 x 10 BRG3054 1 7 Key 18 x 11 x 70 FAS8128 1 8 Plug 3/8 HYD1403 1 9 Copper Washer 16 x 22 x 1 FAS4812C 2 10 Gear 32 tooth SC3275 1 11 Spacer SC3960 1 12 Internal circlip 80mm FAS7108 4 13 Level / drain plug FAS1404 1 14 Cap AT1559 3 15 Taper roller bearing 30208 BRG1222 4 16 Lay shaft SC3277 1 17 Setscrew M16 x 25 FAS2770 1 18 Breather SC3288 1 19 Gear 26 tooth SC3278 1 20 Cap 22x4 SC3961 1 21 External circlip 46mm FAS7015 1 22 Bottom cover SC3287 1 23 Setscrew M8 x 16 FAS2625 4 24 Double lip seal 40 x 80 x10 BRG3051 1 25 Shim set 79.7 SC3279 1 26 Input shaft SC3250 1 27 Setscrew M16 x 25 FAS2770 1 28 Setscrew M10 x 25 FAS2654 8 29 Front cover SC3281 1 30 90 o elbow SC3282 1 10
BIMA DISCHARGE ROTOR GEARBOX WITH SIDE OUTPUT Used on Tomahawk 8080 models from serial number 2600 to 2899 Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Lever SC3420 1 2 Hub SC3421 1 3 Gear SC3422 1 4 Shaft SC3423 1 5 Gear SC3424 1 6 Shaft SC3425 1 7 Gear SC3426 1 8 Sleeve SC3427 1 9 Gear SC3428 2 10 Sleeve SC3429 1 11 Shaft SC3430 1 12 Shaft SC3431 1 13 Gear SC3432 1 14 Hub SC3433 1 15 Sleeve SC3434 1 16 Housing SC3435 1 17 Cover SC3436 1 18 Pad SC3437 1 19 Circlip D16E FAS7123 1 20 Circlip D45E FAS7021 1 21 Circlip D85I FAS7022 3 22 Circlip D95E FAS7023 1 23 Circlip D100I FAS7122 1 24 Circlip D110I FAS7121 1 25 Oil seal 45x85x10 BRG3055 2 26 Oil seal 60x110x13 BRG3056 1 27 Oil seal OR3043 BRG3057 1 28 Key 18x11x70 SC3438 1 29 Key 20x12x21 SC3439 1 30 Bearing 6209 BRG1063 1 31 Bearing 30209 BRG1064 3 32 Bearing 30209 BRG1064 2 33 Bearing 6212 BRG1066 2 34 Spring SPR1022 1 35 Ball 5/16 SC3440 1 36 Sleeve 16x24x0.4 SC3441 3 37 Pin 6x30 UNI 6874 FAS4120 1 38 Oil plug ½ G SC3443 1 39 Oil plug ½ G SC3442 2 40 Setscrew M10 x 55 UNI 5931 FAS2441 4 41 Oil plug RCA 85 SC3444 1 42 Oil plug RCA100 SC3445 1 43 Setscrew M6 x 16 UNI 5739 FAS2440 10 Gearbox oil EP90 7 litres 11
COMER DISCHARGE ROTOR GEARBOX EXTENDED INPUT SHAFT Used on Tomahawk 8080 models from serial numbers 2500 to 2509, 2511, 2521 to 2599 Ref Description Part No. Q ty Ref Description Part No. Q ty 1 Casing SC3270 1 2 Selector SC3271 1 3 Gear 36 tooth SC3272 1 4 Key 14 x 9 x 25 FAS8127 1 5 Gear 26 tooth SC3273 1 6 Key 18 x 11 x 70 FAS8128 1 7 Output shaft SC3274 1 8 Bearing 6212 BRG1019 2 9 Gear 32 tooth SC3275 1 10 Taper roller bearing 30208 BRG1222 4 11 Cap AT1559 3 12 Spacer SC3276 1 13 Lay shaft SC3277 1 14 Internal circlip 80mm FAS7108 4 15 Gear 26 tooth SC3278 1 16 Input shaft SC3250 1 17 External circlip 46mm FAS7015 1 18 Shim set 79.7 SC3279 1 19 Double lip seal 40 x 80 x 10 BRG3051 1 20 Level / drain plug FAS1404 1 21 Gear 23 tooth SC3280 1 22 Setscrew M10 x 25 (8.8) FAS2654 8 23 Front cover SC3281 1 24 External circlip 95mm FAS7017 1 25 Plug 3/8 HYD1403 1 26 90 elbow SC3282 1 27 Breather SC3288 1 28 Selector handle SC3283 1 29 Spring tension pin 6 x 25 FAS4133 1 30 Wiper seal 16 x 22 x 3/4 HYD4525 1 31 Selector handle shaft SC3284 1 32 Bonded seal 3/8 HYD4202 1 33 Spring housing SC3285 1 34 Plain nut M16 FAS2305P 1 35 Grub screw M10 x 14 FAS8449 1 36 Roll pin 6 x 30 FAS4120 1 37 Roll pin 3.5 x 30 FAS4172 1 38 Spring SC3289 2 39 Ball 8.7 SC3286 1 40 Setscrew M8 x 16 FAS2625 4 41 Bottom cover SC3287 1 42 Double lip seal 60 x 80 x 10 BRG3054 1 12
BIMA DISCHARGE ROTOR GEARBOX EXTENDED INPUT SHAFT Used on Tomahawk 8080 models from serial numbers 2510, 2512 to serial number 2520 Details not available at this time. Please Contact Teagle For Advice. Ref Description Part No. Q ty Ref Description Part No. Q ty 13
CROSS BEATER GEARBOX Used on Tomahawk 8080 models from serial number 2501 To serial number 2599 Keyed Splined Keyed Splined Ref Description gears gears Q ty Ref Description gears gears Q ty 1 Cap SC3254 SC3254 1 2 Internal circlip 72 FAS7112 FAS7112 3 3 Shim set 71.7 SC3255 SC3255 1 4 Bearing 6207 BRG1062 BRG1062 2 5 Setscrew M10 x 20 (8.8) FAS2652 FAS2652 4 6 Plug HYD1457 HYD1457 3 7 Cover SC3256 SC3256 1 8 Gear 18 tooth - splined - - - - - SC3257 2 Gear 14 tooth keyed SC3263 - - - - - 2 9 Shim set 48.0 SC3258 SC3258 3 10 Taper roller bearing 30207 - - - - - BRG1207 1 Ball bearing 6207 BRG1062 - - - - - 1 11 Double lip seal 35x72x10 BRG3042 BRG3042 2 12 Output shaft SC3264 SC3259 1 13 Casing SC3260 SC3260 1 14 External circlip 40 FAS7013 FAS7013 1 15 Spacer SC3261 SC3261 1 16 External circlip 35 FAS7016 FAS7016 1 17 Input shaft SC3265 SC3262 1 Key 10 x 8 x 35 FAS8126 - - - - - 2 14
COMER (EG TRANSMISSIONS) PTO SHAFT TOMAHAWK 808 3 POINT LINKAGE MOUNTED MACHINES ONLY **Parts for shafts with either a black plastic sliding sleeve collar or the metal sliding sleeve collar **Steel **Plastic Common Parts Ref Description Part No. Part No. Q'ty. Ref. Description Part No. Qty. PTO Shaft comp. 540rpm PTO8084 PTO8084 1 Tractor end half shaft PTO1928 PTO1928 1 complete with guard. Machine end half shaft PTO1929 PTO1929 1 complete with guard. 1 Outer circlip PTO2711 PTO1902 1 2 Sliding sleeve collar PTO2712 PTO1903 1 3 Ball hold up ring - - - - - - - PTO1904 1 4 Spring PTO2713 PTO1905 1 5 Spring push ring PTO1906 PTO1906 1 6 Inner circlip 1300-72 FAS7112 FAS7112 1 7 Retaining washer PTO1907 PTO1907 1 8 Hub - 6 spline PTO2714 PTO1908 1 Hub- 21 spline PTO2715 PTO1909 1 9 Ball PTO1910 PTO1910 3 10 Ratchet tooth PTO1911 PTO1911 3 11 Ratchet spring PTO1912 PTO1912 3 12 Retaining washer PTO1913 PTO1913 1 13 Outer casing with yoke PTO1914 PTO1914 1 14 Grease nipple BRG5033 BRG5033 1 M8 x 1 straight 15 Cross journal kit PTO2321 PTO2321 1 16 Grease nipple BRG5049 BRG5049 2 M8 x 1 x 45 o 17 Outer tube yoke PTO1915 PTO1915 1 15 18 Spring tension pin 10 x 80 FAS4147 1 19 Outer Tube PTO1916 1 20 Inner tube PTO1917 1 21 Spring tension pin 10 x 70 FAS4145 1 22 Inner tube yoke PTO1918 1 23 Dirt Shield PTO1919 1 24 Spring PTO1921 8 25 Flanged yoke PTO1920 1 26 Bush PTO1922 1 27 Friction lining 153 x 91.5 x 3 PTO2029 2 28 Splined hub c/w item 29 PT01923 1 29 Bolt M12 x 65 FAS4720 2 Locknut M12 FAS4714 2 30 Inner plate PTO1962 2 31 Pressure plate PTO1963 1 32 Bolt M10 x 80 FAS9688 8 Locknut M10 FAS2333 8 33 Outer guard retaining ring PTO1925 1 34 Inner guard retaining ring PTO1926 1 35 Guard bolt PTO1930 6 36 Chain PTO2336 1 37 PTO Guard complete PTO1927 1 * Spring length to give correct slip clutch torque setting is 32.5mm.
COMER PTO SHAFT COMBINED SLIP & OVERRUN CLUTCH TOMAHAWK 808 3 POINT LINKAGE MOUNTED MACHINES ONLY Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO8084 PTO8072 PTO2785 PTO2786 PTO2787 1 Pull back collar set PTO2771 1 2 6 Spline yoke PTO2775 1 21 Spline yoke PTO2784 1 3 Cross journal kit - c.v. joint PTO2321 2 4 Outer yoke PTO1915 1 5 10 x 80mm Spring tension pin FAS4147 1 6 Outer tube PTO1916 1 7 Inner tube PTO1917 1 8 10 x 70mm Spring tension pin FAS4145 1 9 Inner yoke PTO1918 1 10 M10 x 100mm Bolt FAS2065 8 M10 Locknut FAS2333 8 11 Flanged yoke PTO2070 1 12 Bush PTO2071 1 13 Clutch plate 152.5 x 102 PTO2058 4 14 Overrun clutch body PTO2072 1 15 Inner plate PTO2073 2 16 Intermediate plate PTO2074 1 17 Pressure plate PTO2075 1 18 Spring PTO2076 8 19 Inner circlip FAS7112 2 20 Retaining washer PTO2077 2 21 Spring PTO1912 3 22 Ratchet tooth PTO1911 3 23 Hub - 6 spline PTO2788 1 24 Clamp plate PTO2789 2 25 Bolt M12 Fine x 95 FAS4725 2 Locknut M12 Fine FAS4714 2 26 Outer guard retaining ring PTO2768 1 27 Chain MB0952 2 28 Inner guard retaining ring PTO2769 1 29 Outer half guard PTO2778 1 30 Inner half guard PTO2777 1 * Spring length to give correct slip clutch torque setting is 35.2mm 16
COMER (EG TRANSMISSIONS) PTO SHAFT - TOMAHAWK 808, 8080 & 9090 **Parts for shafts with either a black plastic sliding sleeve collar or the metal sliding sleeve collar **Steel **Plastic 2 Plate 4 Plate Ref Description Part No. Part No. Q ty Ref Description Clutch Clutch Q ty PTO Shaft comp. 540rpm PTO8086 PTO8086 1 Tractor end c/w guard PTO2708 PTO2708 1 Machine end c/w guard 2 Plate Clutch PTO2758 PTO2758 1 4 Plate Clutch PTO2709 PTO2709 1 1 Outer circlip PTO2711 PTO1902 1 2 Sliding sleeve collar PTO2712 PTO1903 1 3 Ball hold up ring - - - - - - - PTO1904 1 4 Spring PTO2713 PTO1905 1 5 Spring push ring PTO1906 PTO1906 1 6 Inner circlip 1300-72 FAS7112 FAS7112 1 7 Retaining washer PTO1907 PTO1907 1 8 Hub - 6 spline PTO2714 PTO1908 1 Hub - 21 spline PTO2715 PTO1909 1 9 Ball PTO1910 PTO1910 3 10 Ratchet tooth PTO1911 PTO1911 3 11 Ratchet spring PTO1912 PTO1912 3 12 Retaining washer PTO1913 PTO1913 1 13 Outer casing with yoke PTO1914 PTO1914 1 14 Grease nipple M8 BRG5033 BRG5033 1 15 Cross journal kit PTO2321 PTO2321 1 16 Grease nipple M8x45 o BRG5049 BRG5049 2 17 Outer tube yoke PTO1915 PTO1915 1 18 Spring tension pin 10x80 FAS4147 FAS4147 1 19 Outer tube PTO2705 PTO2705 1 17 20 Inner tube PTO2706 PTO2706 1 21 Spring tension pin FAS4145 FAS4145 1 10 x 70 22 Inner tube yoke PTO1918 PTO1918 1 23 Spring PTO1921 PTO1921 8 24 Flanged yoke PTO1920 PTO1920 1 25 Bush PTO1922 PTO1922 1 26 Friction lining PTO2029 - - - - - - - 2 153 x 91.5 x 3 - - - - - - - PTO2029 4 27 Splined hub PTO1992 PT01992 1 28 Bolt M12 x 65 FAS4720 FAS4720 2 Locknut M12 FAS4714 FAS4714 2 29 Inner plate PTO1962 PTO1962 2 30 Small Inner Plate - - - - - - - PTO1993 1 31 Pressure plate PTO1963 PTO1963 1 32 Bolt M10 x 100 - - - - - - - FAS9669 8 Bolt M10 x 80 FAS9665 - - - - - - - - Locknut M10 FAS2333 FAS2333 8 33 Outer retaining ring PTO1925 PTO1925 1 34 Chain PTO2336 PTO2336 1 35 Inner retaining ring PTO1926 PTO1926 1 36 Guard bolt PTO1930 PTO1930 6 37 Guard complete PTO2704 PTO2704 1 Spring Length to give correct slip clutch torque setting is :- 4 Plate Clutch = 32.0 mm 2 Plate Clutch = 32.5 mm
COMER PTO SHAFT COMBINED SLIP & OVERRUN CLUTCH. TOMAHAWK 808, 8080 & 9090 Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO8086 PTO8080 PTO2785 PTO2786 PTO2793 1 Pull back collar set PTO2771 1 2 6 Spline yoke PTO2775 1 21 Spline yoke PTO2784 1 3 Cross journal kit - c.v. joint PTO2321 2 4 Outer yoke PTO1915 1 5 10 x 80mm Spring tension pin FAS4147 1 6 Outer tube PTO1915 1 7 Inner tube PTO2706 1 8 10 x 70mm Spring tension pin FAS4145 1 9 Inner yoke PTO1918 1 10 M10 x 100mm Bolt FAS2065 8 M10 Locknut FAS2333 8 11 Flanged yoke PTO2070 1 12 Bush PTO2071 1 13 Clutch plate 152.5 x 102 PTO2058 4 14 Overrun clutch body PTO2072 1 15 Inner plate PTO2073 2 16 Intermediate plate PTO2074 1 17 Pressure plate PTO2075 1 18 Spring PTO2076 8 19 Inner circlip SPR7112 2 20 Retaining washer PTO2077 2 21 Spring PTO1912 3 22 Ratchet tooth PTO1911 3 23 Ball ½ PTO2726 3 24 Hub - 6 spline PTO1908 1 25 Spring push ring PTO1906 1 26 Spring PTO2713 1 27 Sliding sleeve collar PTO2712 1 28 Outer circlip PTO2711 1 29 Outer guard retaining ring PTO2768 1 30 Chain PTO2336 2 31 Inner guard retaining ring PTO2769 1 32 Outer half guard PTO2790 1 33 Inner half guard PTO2791 1 * Spring length to give correct slip clutch torque setting is 35.2mm 18
COMER PTO SHAFT WIDE ANGLE C.V. JOINT FOR TRAILED MACHINES Tube Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO Shaft complete 1000rpm Tractor end half shaft complete with guard 540rpm Tractor end half shaft complete with guard 1000rpm Machine end half shaft complete with guard. PTO1413 PTO1414 PTO2737 PTO2738 PTO2739 1 6 Splined wide angle collar yoke PTO272 1 21 Splined wide angle collar yokepto2059 1 2 Cross journal kit - c.v. joint PTO1975 2 3 Wide angle double yoke PTO1967 1 4 Outer yoke PTO2728 1 5 10 x 80mm Spring tension pin FAS4147 1 6 Outer cap PTO2729 1 7 Outer tube PTO2730 1 8 Wiper PTO2731 1 9 Outer circlip PTO2711 1 10 Sliding sleeve collar PTO2712 1 11 Spring PTO2713 1 12 Fixed sleeve PTO2725 1 13 Ball ½ PTO2726 6 14 6 Splined collar yoke PTO2727 1 21 Splined collar yoke PTO2740 1 15 Wide angle c.v. joint-outer tube PTO2736 1 16 Inner tube PTO2732 1 17 Inner cap PTO2733 1 18 10 x 70mm Spring tension pin FAS4145 1 19 Inner yoke PTO2734 1 20 Cross journal assembly PTO2321 1 21 M10 x 100mm Bolt FAS2065 8 M10 Locknut FAS2333 8 22 Flanged yoke PTO2070 1 23 Bush PTO2071 1 24 Clutch plate 152.5 x 102 PTO2058 4 25 Overrun clutch body PTO2072 1 26 Inner plate PTO2073 1 27 Intermediate plate PTO2074 1 28 Pressure plate PTO2075 1 29 Spring PTO2076 8 30 Inner circlip FAS7112 2 31 Retaining washer PTO2077 2 32 Spring PTO1912 3 33 Ratchet tooth PTO1911 3 34 Hub - 6 spline PTO1908 1 35 Spring push ring PTO1906 1 Bolt Type EN Guard CE Guard 2005 On 36 Inner guard retaining ring PTO1926 PTO2769 1 37 Bolt PTO1930 - - - - - - - 6 38 Outer guard retaining ring PTO1925 PTO2768 1 39 Bearing ring PTO1973 PTO2794 1 40 Guard cone set PTO1974 PTO1974 1 41 Outer half guard PTO1971 PTO1971 1 42 Chain PTO2336 PTO2336 3 43 Inner half guard PTO1972 PTO1972 1 * Spring length to give correct slip clutch torque setting is 35.2mm 19
EG TRANSMISSIONS PTO SHAFT WIDE ANGLE C.V. JOINT Tube Section Ref Description Part No. Q'ty Ref Description Part No. Q'ty PTO Shaft complete 540rpm PTO1413 1 PTO Shaft complete 1000rpm PTO1414 1 Tractor end half shaft PTO2062 1 complete with guard 540rpm Tractor end half shaft PTO2061 1 complete with guard 1000rpm Machine end half shaft PTO2063 1 complete with guard. 1 6 Splined wide angle yoke PTO2060 1 21 Splined wide angle yoke PTO2059 1 2 Cross journal kit - c.v. joint PTO1975 2 3 Wide angle double yoke PTO1967 1 4 Outer tube yoke PTO1968 1 5 10 x 80mm Spring tension pin FAS4147 1 6 Outer tube rislan coated PTO1969 1 7 Push pin PTO1933 2 8 Wide angle joint 540rpm PTO2078 1 Wide angle joint 1000rpm PTO2079 1 9 Inner tube rislan coated PTO1970 1 10 10 x 70mm Spring tension pin FAS4145 1 11 Inner tube yoke PTO1918 1 12 Cross journal assembly PTO2321 1 13 M10 x 100mm Bolt FAS2065 8 M10 Locknut FAS2333 8 14 Flanged yoke PTO2070 1 15 Bush PTO2071 1 16 Clutch plate 152.5 x 102 PTO2058 4 17 Overrun clutch body PTO2072 1 20 18 Inner plate PTO2073 1 19 Intermediate plate PTO2074 1 20 Pressure plate PTO2075 1 21 Spring PTO2076 8 22 Overrun + slip clutch assy PTO2089 1 23 Inner circlip FAS7112 2 24 Retaining washer PTO2077 2 25 Spring PTO1912 3 26 Ratchet tooth PTO1911 3 27 Ball PTO1910 3 28 Hub - 6 spline PTO1908 1 29 Spring push ring PTO1906 1 30 Spring PTO1905 1 31 Ball hold up ring PTO1904 1 32 Sliding sleeve collar PTO1903 1 33 Outer Circlip PTO1902 1 34 Chain PTO2336 3 35 Inner guard retaining ring PTO1926 1 36 Bolt PTO1930 6 37 Outer guard retaining ring PTO1925 1 38 Bearing ring PTO1973 1 39 Guard cone set PTO1974 1 40 Outer half guard PTO1971 1 41 Inner half guard PTO1972 1 * Spring length to give correct slip clutch 35.2 mm
NOTES 21