1 920 1920P01 Differential Pressure Sensors for neutral and mildly corrosive liquids and gases QBE63-DP Differential pressure sensor, suitable for gases and liquids, for the measurement of positive and negative pressures and pressure differentials in HVAC systems Hall-effect transducer technology Highly resistant to positive pressure Simple, robust construction for highly reliable operation For neutral and mildly corrosive liquids and gases Supply voltage AC 24 V or DC 2030 V DC 010 V output signal Female-threaded G 1 /8" connection Use The QBE63-DP differential pressure sensors are particularly suitable for use in HVAC systems for continuous monitoring of the level or flow rate of neutral or mildly corrosive gases or liquids The pressure being monitored acts on a measuring system comprising a diaphragm, permanent magnet and Hall-effect transducer The measured pressure is converted electronically into a linear DC 0 10 V output signal Types Type Pressure range QBE63-DP01 0 100 mbar 0 10 kpa QBE63-DP02 0 200 mbar 0 20 kpa QBE63-DP05 0 500 mbar 0 50 kpa QBE63-DP1 0 1 bar 0 100 kpa CA1N1920E 06062005 Siemens Building Technologies Landis & Staefa Division
Ordering and delivery When ordering, please specify the quantity, product name and type code Example: 1 differential pressure sensor, type QBE63-DP05 and 2 mounting kits, type AQB511 A suitable fixing bracket is supplied with the sensor Any accessories required must be ordered separately Compatibility The QBE63-DP differential pressure sensors can be used in conjunction with all devices or systems capable of processing the DC 010 V output signal Technology The pressure to be monitored acts on an EPDM diaphragm which deflects a spring As a result of the pressure and consequent movement of the diaphragm, a permanent magnet attached to the diaphragm changes its position in relation to the Hall-effect transducer on the outside of the pressure housing The transducer delivers an electrical signal proportional to the magnetic field This signal is linearised, temperaturecompensated and amplified by the built-in electronics Cross-section 920072 6 5 4 3 p2 7 2 p1 1 Key: 1) Pressure housing (measuring chamber) 2) Diaphragm and spring 3) Permanent magnet 4) Hall-effect transducer with measuring electronics 5) Cover 6) Cable entry with PG9 gland 7) Purging points p1 G 1 /8" threaded connection for higher pressure or lower vacuum p2 G 1 /8" threaded connection for lower pressure or higher vacuum Mechanical design The QBE63DP differential pressure sensors comprise: Plastic housing with Pg 9 cable gland Pressure casing with diaphragm and spring Printed circuit board with Hall-effect transducer Fixing bracket 2/6 Siemens Building Technologies Differential pressure sensors QBM63-P CA1N1920E HVAC Products 06062005
Accessories AQB511 Mounting kit comprising: 2 brass thread adapters, 2 x G 1 /8", male 2 copper seal, 1 /8" 1 m copper capillary with retaining nuts at each end, G 1 /8" female 1 thread adapter, G 1 /8" female to G 1 /2" female, with 1 copper seal, 1 /2" Thread adapter, G 1 /8" female to R 1 /2" male Mounting instructions (no 35757) The components of the AQB51 mounting kit are supplied by SERTO, but the kit must be ordered from HVAC Products (SBT) Other mounting arrangements can be ordered directly from the SERTO range 80364a Mounting instructions Mounting instructions are enclosed with the differential pressure sensor The QBE63-DP sensors can be connected directly with G 1 /8" or R 1 /8" screwed fittings Special precautions must be taken on site when mounting the sensors, to ensure airtight screw connections Recommended measures: Important note Use standard T-fittings or drill and de-bur measuring holes, each 5 mm diameter, for the pressure tapping points (A) An isolating bypass (5) can be fitted to avoid overloading the pressure sensor on one side while making adjustments For inspection purposes, measuring circuits can be fitted with a measuring-t at the sensor head Mounting for use with liquids: Always mount the sensor lower than the pressure measuring points Mount on a vibration-free surface Always evacuate the system ø max 5 mm 90 Supply Return + A A 1 2 5 2 1 4 80357 4 4 3 P1 P2 3 + QBE-DP Key: A Measuring holes 1 Isolating valves (SERTO SO 7100-6 GREY and, if required, screw-on base SERTO SO 09904-4-8) 2 T-joints (SERTO SO 03000-1/8) 3 Connection pieces (from mounting kit AQB 511) 4 Copper pipes (from mounting kit AQB 511) 5 Isolating bypass Siemens Building Technologies Differential pressure sensors QBM63-P CA1N1920E HVAC Products 06062005 3/6
Technical data Electrical interface Power supply Max voltage tolerance Power consumption Current consumption Output signal Low voltage (SELV, PELV) AC 24 V, 50/60 Hz or DC 2030 V +15 / 10 % <1 VA 35 ma DC 010 V, short-circuit-proof and proof against polarity reversal 10 kω Working resistance Product data Differential pressure range Operating range, see Types Measuring element Hall-effect transducer Measuring accuracy <±10 % FS (FS = Full Scale) Hysteresis <±15 % FS Linearity <±15 % FS Temperature drift 008 % FS / K (20 C in relation to zero point) Overload capacity 10 bar (sensor range up to 200 mbar) 20 bar (sensor range from 500 mbar) Burst pressure 30 bar Dynamic response: Response time Load alternation <10 ms <10 Hz Suitable media Admissible temperature of medium Air or mildly corrosive gases and liquids 10+80 C Maintenance No maintenance required Protective data Protection standard IP 65 to IEC 529 (with cover fitted) Combustion class Cover UL 94 HB Connections Connection terminals 3 screw-terminals, 15 mm 2 Cable entry Pg 9 cable gland Pressure connections Female-threaded G1/8" Mounting Mounting bracket For mounting in ducts, on walls or ceilings and in control panels Orientation Any (factory-calibrated with pressure connections at bottom) When used with liquids: purging points at top Environmental conditions Perm ambient temperature Operation Storage/Transport 25 +60 C (electronics) 40 +80 C Perm ambient humidity <90 % r h (non-condensing) Standards Electromagnetic compatibility Immunity to Emissions to EN 50 082-2 EN 50 081-1, EN 50 081-2 conformity to EMC directive 89/336/EWG Materials Pressure casing Nickel-plated brass Cover Cable gland Plastic (ABS without fibre-glass) Polystyrol Diaphragm EPDM (ethylene propylene rubber) Mounting bracket Galvanised steel Mounting kit AQB511 See "Accessories" Weight Including packaging 086 kg 4/6 Siemens Building Technologies Differential pressure sensors QBM63-P CA1N1920E HVAC Products 06062005
Connection terminals G U M + 80358 0 Supply voltage AC 24 V or DC 20 30 V DC 0 10 V output signal (reference point GND) GND Dimensions Fixing bracket 72 43 20 920073 22 G 1/8 94 47 10 ø 5,2 11 18,8 ø 65 G 1/8 46 40 60 63 Dimensions in mm Siemens Building Technologies Differential pressure sensors QBM63-P CA1N1920E HVAC Products 06062005 5/6
6/6 2005 Siemens Switzerland Ltd Subject to changes Siemens Building Technologies Differential pressure sensors QBM63-P CA1N1920E HVAC Products 06062005