MICRO SOLENOID VALVE pinch mechanism for flexible tube O.D..65 to 9.5 mm U / Series 84 FEATURES Solenoid valve suitable for cutting off the flow of a fluid by pinch For sterile, aseptic, physiological and food applications No turbulence when cutting off flow by pinch Silent operation Full bore output flow compared with a traditional solenoid valve Manual pulse control for fitting tube A single component in contact with the fluid, i.e. the tube Bi-directional flow The solenoid valves satisfy all relevant EC directives GENERAL Differential pressure fluids ( ) air, inert gases, water, oil and liquids See «SPECIFICATIONS» [ bar =00 kpa] 0007GB-04/R0 MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Recommended flexible tube VMQ (silicone) (max. hardness: 50 Shore A) The silicone tube is not included in our supply OTHER MATERIALS Body Pinch mechanism Internal parts Guide tube Aluminium, anodised POM (Graphite-reinforced polyacetal) Stainless steel Nickel-plated brass ELECTRICAL CHARACTERISTICS Coil insulation class F Connector Spade plug (cable Ø 4-6 mm or Ø 6-0 mm) Connector specification 4 W/8 W/6 W (DMX) DIN 4650, 9,4 mm, industry standard B 6 W / W (AMX/FNX) ISO 4400 / EN 750-80, form A Electrical safety IEC 5 Electrical enclosure protection Coil type 0 = IP40 / Coil type 0-0 = IP65 Standard voltages DC (=) : V - 4V (Other voltages on request) power ratings operator ambient replacement coil prefix inrush holding hot/cold temperature type () option ~ ~ = range (TS) (VA) (VA) (W) (W) (C ) V DC 4 V DC - - - 4 400568 400569 - - - 8 50070-00 50070-00 0 (DNX-4) SC - - - 6-0 to + 60 50070-00 50070-004 - - - 9 40054 400544 0 (AMX) - - - 40056 40057 0 (FNX) () Refer to the dimensional drawings on the following page. SPECIFICATIONS tube I.D. tube O.D. pinch force min. operating pressure differential (bar) air inert gas ( ) max. (PS) liquids ( ) power coil (W) catalogue number (mm) (mm) (dan) ~ U - Universal 0,76,65 0, 0 0,8 0,8-4 SCH84B004,0,6 0,8 0 0,8 0,8-4 SCH84B00,57,8 0, 0 0,8 0,8-8 SCH84B00 (),98,8 0,8 0 0,8 0,8-6 SCH84B00 (),4 4,7 0,4 0 0,8 0,8-9 SCH84A005 4,8 7,9 0,85 0 0,8 0,8 - SCH84B006 6,4 9,5, 0 0,8 0,8 - SCH84B007 () Observe the minimum of time stated, see graph above. Minimum off time (min) USE IN INTERMITTENT SERVICE Minimum waiting time between each application of power On time (min) 75
OPTIONS AND ACCESSORIES Flexible tubes having to use an external guiding device for optimum support (see dimensions): - with an outside diameter lower than, mm (catalogue numbers SCH84B00 to..b004) - with an outside diameter lower than,5 mm (catalogue number SCH84A005) - with an outside diameter lower than 6 mm (catalogue numbers SCH84B006 and..007) For use on tubes other than those recommended, contact us Plug with visual indication and peak voltage suppression or with cable length of m INSTALLATION The solenoid valves can be mounted in any position without affecting operation However, for optimum performance it is recommended that they be fitted with the solenoid operator at the top Fixing plate built in between the body and the coil for assembly in a bank on a base plate Flexible tubes are not included in our supply Do not connect the solenoid valve to the power supply without fitting a flexible tube beforehand Installation/maintenance instructions are included with each valve ORDERING EXAMPLES: SC H 84 B 00 V / DC SC H 84 B 006 4V / DC prefix pipe thread basic number SOLENOID VALVES SERIES 84 voltage suffix DIMENSIONS (mm), WEIGHT (kg) TYPE 0 Prefix SC Solenoid IEC 5 / DIN 4650 IP40 Type 0: SCH84B00/00/00/004 L C D Type 0: SCH84A005 Type 0: SCH84B006/B007 A TYPE 0-0 Prefix SC Solenoid IEC 5 / ISO 4400 IP65 tube guiding device = T = S U 76 Impulse manual operator V 60 K bottom view Ø E M J G F H R arrangement for wall-fitting K example of banked assembly tube guiding device type prefix catalaogue option number Ø A C D E F G H K L M P Q R S T U V weight () catalogue number weight 0 SC SCH84B00/00 /00/004 6 49,5,5 5 0 66 4 7, M 6,5 0,7 6 4, 5, 0,06 C40094 0,005 0 SC SCH84A005 5 78 4 7 7,5,5 99 9 4,5 M4 5,5 4 5, 8,5 0,0 C40095 0,009 0 SC SCH84B006/B007 0 84 49 8 4,5 4,5,5 99 45,5 4 4,5 M4 0,5 4 0 9 6 99 0,45 C40096 0,05 () Incl. coil(s) and connectors.. Q P 0007GB-0/R0
MICRO SOLENOID VALVES direct operated pad-mounting body for subbase M/M5 NC NO / Series 88 Type Micro 0 GENERAL Fluid Air or inert gas, non-lubricated, filtered at 5 µm Operating pressure 7 bar max. Ambient temperature +5 C to +50 C Flow (Qv at 6 bar) See SPECIFICATIONS Manual operator Impulse-type (without manual operator on request) Switching time 0 ms (<0 ms on request) CONSTRUCTION Body Internal parts Seals PA (polyamide) MXD6 Stainless steel, nickel-plated steel, synthetic material, aluminium NBR (nitrile), FPM (fluoroelastomer) on request ELECTRICAL CHARACTERISTICS voltage (other voltages on request) 4V = V = 5 V = consumption insulation class degree of protection +0%, -5% W -,W F IP 40 The solenoid valves are designed for continuous operation within the maximum ambient temperature limits. electrical connection connector with two 0.5 mm lead wires + built-in LED and electrical protection or cable ends, 0,5 m long 007GB-04/R0 SPECIFICATIONS symbol NC NO orifice size (mm) ( ) Type,,, 4 with LED and electrical protection = horizontal, width 5,08 mm = vertical, width 5,08 mm at 6 bar l/min (ANR) flow coeff. Kv operating pressure (bar) 0,5 0,7 8 0, 0 8 0,8 0,8 0 0,5 0 4 consumption min. max. (W),0,0 0,8 0,5 0,5 0,5 8 0, 0 6 0,8 0,8 0 0,5 0,0,0 0,8 0,5 = horizontal, width,54 mm 4 = vertical, width,54 mm 5 = cable ends 0,5 m long, 0,5 mm² type of electrical connection ( ) catalogue number 88000 880076, 880074 4 880078 5 88007 88008 88008, 88008 4 880084 5 880085 880086 880087, 880088 4 880089 5 880090 88006 880077, 880075 4 880079 5 88007 88009 88009, 88009 4 880094 5 880095 880096 880097, 880098 4 880099 5 88000 77
MICRO SOLENOID VALVES direct operated, with latching coil pad-mounting body for subbase M/M5 NC / NO / Series 88 Type Micro 0 GENERAL Fluid Air or inert gas, non-lubricated, filtered at 5 µm Operating pressure 8 bar max. Ambient temperature +5 C to +50 C Flow (Qv at 6 bar) See SPECIFICATIONS Manual operator Impulse-type (without manual operator on request) Switching time 0 ms (<0 ms on request) CONSTRUCTION Body Internal parts Seals PA (polyamide) MXD6 Stainless steel, nickel-plated steel, synthetic material, aluminium NBR (nitrile), FPM (fluoroelastomer) on request ELECTRICAL CHARACTERISTICS voltage (other voltages on request) 4V = V = 5 V = (+0%, -5%) consumption insulation class degree of protection W -,W F IP 40 The solenoid valves are designed for continuous operation within the maximum ambient temperature limits. electrical connection connector with two 0.5 mm lead wires + built-in LED and electrical protection or cable ends, 0,5 m long SPECIFICATIONS 78 symbol orifice size (mm) at 6 bar l/min (ANR) ( ) type,,, 4 with LED and electrical protection = horizontal, width 5,08 mm = vertical, width 5,08 mm WIRING DIAGRAM CLOSED flow coeff. Kv operating pressure (bar) 0,5 0,7 8 0, 0 7 0,8 0,8 0 0,5 0,0,0 0,8 0 OPEN consumption min. max. (W) type of electrical connection ( ) catalogue number 8800 8800, 8800 4 88004 5 88005 88006 88007, 88008 4 88009 5 8800 880 880, 880 4 8804 5 8805 = horizontal, width,54 mm 4 = vertical, width,54 mm 5 = cable ends, 0,5 m long, 0,5 mm² FUNCTIONAL DIAGRAM 4 VDC 0 VDC coil coil 0 open valve closed valve function with latching coil (no constant current consumption) 007GB-04/R0
MICRO SOLENOID VALVES - SERIE 88 DIMENSIONS (mm), WEIGHT (kg) weight 0,0095 type type Scale Scale type type 4 Scale Scale 007GB-04/R0 type 5 Scale flange facing NO = Pressure = Outlet = Exhaust NC = Pressure = Outlet = Exhaust Use in vacuum (NO) = Vacuum pump = Outlet = Atmosphere Use in vacuum (NC) = Vacuum pump = Outlet = Atmosphere 79
MICRO SOLENOID VALVES - SERIE 88 DIMENSIONS (mm), WEIGHT (kg) solenoid valve mounted on single subbase number of valves subbase catalogue number* 5000 weight 0,05 Scale solenoid valve mounted on multiple subbase Cable ends Horizontal connector Vertical connector Cover number of valves A : Blanking plate, cat. no. 88505 * The connectors must be ordered separately, please indicate the quantity and one of the following codes: Connector, wires Distance between contacts 5,08 mm - Length 0,5 m - cat. no.: 88880 - Length,5 m - cat. no.: 88880 - Length m - cat. no.: 88880 Distance between contacts,54 mm - Length 0,5 m - cat. no.: 888806 - Length,5 m - cat. no.: 888807 - Length m - cat. no.: 888808 80 4 5 50005 6 7 8 9 0 subbase catalogue number* 5000 5000 50004 50006 50007 50008 50009 5000,5 length L L 7,5 44 8 54,5 48,5 65 59 75,5 69,5 86 80 96,5 90,5 07 0 7,5,5 weight 0,05 0,069 0,086 0,04 0, 0,9 0,56 0,75 0,9 Scale 007GB-006/R0
MICRO SOLENOID VALVES direct operated, Large Flow pad-mounting body for subbase M5 NC NO / Series 88 Type Micro 0 GENERAL Fluid Air or inert gas, non-lubricated, filtered at 5 µm Operating pressure 0 bar max. Ambient temperature +5 C to +50 C Flow (Qv at 6 bar) See «SPECIFICATIONS» Switching time 0 ms CONSTRUCTION Body Internal parts Seals PBT (polybutylene terephthalate) Stainless steel synthetic material FPM (fluoroelastomer) ELECTRICAL CHARACTERISTICS voltage ± 0 % (other voltages on request) 4V = V = power ratings ) inrush holding insulation class degree of protection, W, W F IP40 The solenoid valves are designed for continuous operation within the maximum ambient temperature limits. ) The valves are provided with power save electronics and LED which switch to holding power after 00 msec. electrical connection X, X, X, X4, X5 *see Electrical Connection Type *Electrical Connection Type X = type, horizontal, distance between contacts 5,08 mm X = type, vertical, distance between contacts 5,08 mm X = type, horizontal, distance between contacts,54 mm X4 = type 4, vertical, distance between contacts,54 mm X5 = type 5, two leads 0,5 m long, 0,5 mm² Type,,,4,5 with LED, protection and power save electronics. SPECIFICATIONS 00GB-05/R0 symbol NC NO orifice size (mm) at 6 bar l/min (ANR) flow coefficient Kv m³/h operating pressure (bar) consumption min. max. (W) catalogue number,0,0 0,0 0 0, R88BXXVXX,, 9 0,07 0 6, R88B4XXVXX,6,6 4 0,09 0,5, R88B5XXVXX,0,0 0,0 0 8, R88BXXVXX,, 9 0,07 0 4, R88B4XXVXX,6,6 4 0,09 0,5, R88B5XXVXX 8
MICRO SOLENOID VALVES LARGE FLOW - SERIES 88 ORDERING 5-DIGIT PRODUCT CODE R 88 B XX 0 XX Fluid Connection Type R = Pad Mount Voltage F = 4 VDC F = VDC Product Series 88 = Series 88 Micro 0 Manual Override = without manual override Revision B = Micro 0, Revision B (grey) Coil Size & Power-Save = 0 mm with power-save Fastening Screws 0 = without srews = with metric screws M,7x,5 = with selftapping screws KB8x4 Sealing Material V = FPM Valve Type = / NC = / NO Valve Orifice =,0 mm 4 =, mm 5 =,6 mm Electrical Connection Type X = Type, horizontal 5,08 mm X = Type, vertical 5,08 mm X = Type, horizontal,54 mm X4 = Type 4, vertical,54 mm X5 = Type 5, leads 0,5 m x 0,5 mm ORDERING EXAMPLE: R88BXVF = pad mount, series 88, Micro 0 Revision B (grey), with power-save, / NC, orifice,0 mm, Type, FPM, M,7 x,5, without manual override, 4 VDC 8 00GB-05/R0
MICRO SOLENOID VALVES LARGE FLOW - SERIES 88 DIMENSIONS (mm), WEIGHT (kg) weight 0,007 type type Scale : Scale : type type 4 Scale : Scale : 00GB-008/R0 type 5 Scale : flange facing 8
MICRO SOLENOID VALVES LARGE FLOW - SERIES 88 DIMENSIONS (mm), WEIGHT (kg) (kg) solenoid valve mounted on single subbase number of valves subbase catalogue number* 50007 weight 0,07 solenoid valve mounted on multiple subbase A number of valves 4 5 5000 6 7 8 9 0 subbase catalogue number* 50098 50099 50000 5000 5000 50004 50005 50006 L 5,7 length L 9,7 46, 40, 56,7 50,7 67, 6, 77,7 7,7 88, 8, 98,7 9,7 09, 0, 9,7,7 weight 0,066 0,09 0,6 0,4 0,67 0,9 0,6 0,4 0,68 A: Blanking plate, catalogue number: 5697-00 * The connectors must be ordered separately, please indicate the quantity and one of the following codes: Connector, wires Distance between contacts 5,08 mm - length 0,5 m - catalogue number: 88880 - length,5 m - catalogue number: 88880 - length m - catalogue number: 88880 Distance between contacts,54 mm - length 0,5 m - catalogue number: 888806 - length,5 m - catalogue number: 888807 - length m - catalogue number: 888808 A L 00GB-05/R0 84
MINI-SOLENOID VALVES ISO 58 (CNOMO, size 5) interface direct operated, pad mounting body connector size 5 NC / Series 0 FEATURES Compact, monobloc solenoid pilot valve with spade-plug connector type DIN 4650, form C, with 9,4 mm spacing, or to ISO 57/DIN 4650 form C, with 8 mm spacing. Version with or without integrated LED and electrical protection. LED indicator visible from sides. The solenoid valves satisfy all relevant EC directives. GENERAL Differential pressure See «SPECIFICATIONS» [ bar = 00 kpa] Pneumatic base ISO 58 (CNOMO E06.6.0N, size 5) Connection Subbase Response time 8-5 ms fluids ( ) temperature range (TS) seal materials ( ) air or inert gas -5 C to +60 C (LP) () NBR (nitrile) filtered at 50 µm, lubricated or not -5 C to +60 C /+50 C (LP) () FPM (fluoroelastomer) () LP, LP: see "electrical characteristics" table MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body PARA Internal parts POM, PET, stainless steel and brass Seals NBR (disc), FPM (others) Pneumatic interface seal TPE OTHER MATERIALS Coil Thermoplastic PET ELECTRICAL CHARACTERISTICS Coil insulation class F Connector Spade plug (cable Ø 4-6 mm) Connector specification DIN 4650, 9,4 mm, form C or ISO 57 / DIN 4650, 8 mm, form C Electrical safety IEC 5 Electrical enclosure protection Moulded IP65 (EN 6059) Standard voltages DC (=) : 4V (Other voltages on request) AC (~) : 4V - 5V - 0V / 50-60 Hz power ranges coils power ratings ( ) operator voltages (V) inrush ~ holding ~ hot/cold = ambient temperature range (4) (TS) ~ = (VA) (VA) (W) (W) ( C) LP 4-5 4,4,, /, -5 to +60 LP 0 4,,6,5 /,65-5 to +60 (~)/+50 (=) () type () () Refer to the dimensional drawings on the following page.. () With LED, see page 90 (4) For joinable subbase mounting, see page 90. 0 PNEUMATIC-ELECTRIC interface (available on request) PNEUMATIC CNOMO interface (standard) ( ) Nominal power ratings of versions without LED indicator and electrical protection. For versions with LED indicator and electrical protection, add: 0,5 W with DC (=) 0,4 W / VA with AC (~) 0007GB-0/R0 SPECIFICATIONS orifice size at 6 bar l/min (ANR) flow ~ = with connector --A --D without connector --L --P coefficient Kv operating pressure differential (bar) When ordering, please specify in addition to the basic catalogue number: the type of current: voltage / frequency + the version: with or without connector to be inserted after the basic catalogue number power ranges impulse basic catalogue number manual operator maintained 9,4 mm 8 mm 9,4 mm 8 mm (mm) min. max. (PS) ~ ~ NC - Normally closed (Without LED and protection) 0,6 0 0, 0,6 0 0 LP 0007 00007 0008 00008 0,8 7 8 0, 0,5 0 8 LP 000 0000 00 000, 5 0,5 0,50 0 5 LP 006 0006 007 0007 0 0 LP 009 0009 000 0000,5 9 5 0,50 0,56 0 LP 00 000 00 000 0 6 LP 005 0005 006 0006 NC - Normally closed (With LED and protection) (5) 0,6 0 0, 0,6 0 0 LP 05007 04007 05008 04008 0,8 7 8 0, 0,5 0 8 LP 0500 0400 050 040, 5 0,5 0,50,5 9 5 0,50 0,56 (5) Only available in 4 V AC/DC and 5 V AC. 0 5 LP 0506 0406 0507 0407 0 0 LP 0509-0500 - 0 LP 050 040 050 040 0 6 LP 0505-0506 - Examples: with connector 4V DC : 0007--D 4V DC without connector 4V DC : 0007--P 4V DC 85
OPTIONS AND ACCESSORIES Seals and disc made of FPM (fluoroelastomer) Versions without manual operator and NO (Normally Open): contact us Version with pneumatic-electric interface Version V DC, LP, connector DIN 4650, 9,4 mm, industry standard B Connector ISO 57 / DIN 4650, 8 mm, form C: - standard: catalogue number 880 - with cable m length: catalogue number 8804 Connector DIN 4650, 9,4 mm, form C: - standard: catalogue number 88458 - with cable m length: catalogue number 884567 Explosionproof enclosures for use in zones 0/0-/-/, categories -- to ATEX Directive 94/9/EC (see Explosionproof solenoids section) INSTALLATION The solenoid valves can be mounted in any position without affecting operation Solenoid valve supplied with mounting screws and mounting pad seal(s) Installation/maintenance instructions are included with each valve DIMENSIONS (mm), WEIGHT (kg) TYPE 0 IEC 5 / DIN 4650 IP65 Subbase mounting surface: ISO 58 (CNOMO E06.6.0N, size 5) 56 47 4 4,5 0 50 90 8, 9,7 5 connection function NC P O - P: Pressure O: Outlet,8,8 9,7 5 8, x Ø x Ø,5 A Manual operator location Z mounting screw M x 0 E Version with LED and electrical protection weight () 0,047 () with standard connector. 86 0007GB-0/R0
MINI-SOLENOID VALVES ISO 58 (CNOMO, size 5) interface direct operated, pad mounting body connection M or with cable ends NC / Series 0 FEATURES Compact, monobloc solenoid pilot valve with M connector or cable ends Version with integrated LED indicator and electrical protection. LED indicator visible from sides The solenoid valves satisfy all relevant EC directives GENERAL Differential pressure See «SPECIFICATIONS» [ bar = 00 kpa] Pneumatic base ISO 58 (CNOMO E06.6.0N, size 5) Connection Subbase Response time 8-5 ms fluids ( ) temperature range (TS) seal materials ( ) air or inert gas filtered at 50 µm, lubricated or not - 5 C to + 60 C (LP) () NBR (nitrile) FPM (fluoroelastomer) () LP: see "electrical characteristics" table MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body PAA Internal parts POM, PET, stainless steel and brass Pneumatic interface seal TPE OTHER MATERIALS Coil Thermoplastic PET 0007GB-0/R0 ELECTRICAL CHARACTERISTICS Coil insulation class F Connection Connector M or cable ends Electrical safety IEC 5 connector M CNOMO E0.6.50.N cable ends EN 6070 Electrical enclosure protection Moulded IP67 (EN 6059) Standard voltages DC (=) : 4V power ranges coils power ratings ( ) operator ambient voltages inrush holding hot/cold temperature (V) ~ ~ = range () (TS) type () ~ = (VA) (VA) (W) (W) ( C) LP - 4 - - -,5 /,5-5 to + 60 0-0-0 () Refer to the dimensional drawings on the following page. () For joinable subbase mounting, see page 90. SPECIFICATIONS ( ) Nominal power ratings of standard versions (with LED indicator and electrical protection) flow orifice operating pressure basic catalogue number at 6 bar coefficient power size differential (bar) l/min (ANR) Kv ranges manual operator (mm) min. max. (PS) impulse maintained NC - Normally closed, connection M + LED and protection,5 9 5 0,50 0,56 0 LP 00 00 NC - Normally closed, cable ends + LED and protection,5 9 5 0,50 0,56 0 LP 00 00 When ordering: with connector without connector complete Examples: M with connector M without connector cable ends M --D --P cable --D : 00--D : 00--P : 00--D to be inserted after the basic catalogue number 87
MINI-SOLENOID VALVES SERIES 0 OPTIONS AND ACCESSORIES Seals and disc made of FPM (fluoroelastomer) Versions without manual operator and NO (Normally Open): contact us Version with pneumatic-electric interface Straight M connector: - with 5 m cable length: catalogue number 880 Explosionproof enclosures for use in zones 0/0-/-/, categories -- to ATEX Directive 94/9/EC (see Explosionproof solenoids section) INSTALLATION The solenoid valves can be mounted in any position without affecting operation Solenoid valve supplied with mounting screws and mounting pad seal(s) Installation/maintenance instructions are included with each valve DIMENSIONS (mm), WEIGHT (kg) TYPE 0 IEC 5 Connection M IP67 TYPE 0 IEC 5 Straight M connector, 5 m cable length IP67 47 47 4,8,8 8, 9,7 4,5 0 5 9 7 4,5 0 75 8, 9,7 5 7 A Manual operator location. Z mounting screw M x 0 M () () () weight cable ends 0,049 0,88 0,040 () Without connector () With connector 47 4,5 TYPE 0 IEC 5 Cable ends 0, m length IP67 0,5 8, 88 9,7 5 connection function NC P O - P: Pressure O: Outlet Subbase mounting surface: ISO 58 (CNOMO E06.6.0N, size 5),8,8 9,7 5 8, x Ø x Ø,5 0007GB-00/R0
MINI-SOLENOID VALVES SERIES 0 DIMENSIONS (mm), WEIGHT (kg) Single subbase Aluminium or brass 60 45 0 0 x Ø M5 5 9 5 65 90 5,5 5 A Mounting: holes M, depth 4,5 Orifice () can be connected on the left or on the right of the subbase. material catalogue number weight () aluminium 88600 0,0 brass 00000 0,04 () subbase alone Adapter CNOMO size 0 (only for NC version) Aluminium 6 48 90 A Mounting: screws M4 x 0 (supplied) 6,5 0 60 6 7,5 9 4,5 catalogue number weight () 88600 0,08 () adapter alone Joinable subbases Aluminium 0007GB-008/R0,5 Ports and : G/8,5 8,5 Port : coupling for 4mm OD tube 4,5,5 A Fixing hole Ø, ( for 4x ; for x) Z Fixing hole M, depth 8 ( for 4x ; for x) E Mating surface blanking plates (option) R TS5 DIN rail (not supplied) T Clip for DIN rail mounting (option) 4 5 8,5 7 7 7 8,58,5 7 8,5 68 (4x) L 4 (x) 9 0 50 catalogue number x subbases L weight () 5500564 x - 0,076 5500565 4 4x - 0,48 5500566 6 4x + x 4 0,6 5500567 8 4x + 4x 48 0, 5500568 0 4x + 4x + x 8 0,89 5500569 4x + 4x + 4x 6 0,466 () subbases alone x = place for mini-solenoid valves. plugs R/8 supplied. 58 89
MINI-SOLENOID VALVES SERIES 0 OPTIONS AND ACCESSORIES Additional subbase with places (with seals): catalogue number 5500570 tie-rods + nuts for a subbase with: 4 places: catalogue number 880075 6 places: catalogue number 880075 8 places: catalogue number 8800754 0 places: catalogue number 8800755 places: catalogue number 8800756 Mounting kit for DIN rail ( clips + screws + washers): catalogue number 8800757 Mating surface blanking plate: catalogue number 8800 AMBIENT TEMPERATURE RANGES current type DC (=) AC (~) power range () Voltage: -5% / +0% () Voltage: -5% / +0% inrush/ holding (VA) ~ power coil hot/cold (W) = version - /, standard -5 C ; +60 C LP () -5 C ; +60 C -,5/,5 LED + protection -5 C ; +40 C - /,65 standard -5 C ; +50 C -5 C ; +40 C LP () -,5/,8 LED + protection -5 C ; +40 C -,4/, - standard LP () -5 C ; +60 C -5 C ; +40 C,8/,6 - LED + protection,/,6 - standard -5 C ; +60 C -5 C ; +40 C LP (),5/ - LED + protection -5 C ; +50 C - 90 0007GB-00/R0
MINI-SOLENOID VALVES ISO 58 (CNOMO, size 5) interface direct operated, pad mounting body connector size 5 NC NO U / Series 0 FEATURES Compact, monobloc solenoid pilot valve with spade-plug connector type DIN 4650, industry standard form C, with 9,4 mm spacing, or to ISO 57/DIN 4650 form C, with 8 mm spacing Version with or without integrated LED and electrical protection LED indicator visible from sides The solenoid valves satisfy all relevant EC directives GENERAL Differential pressure See «SPECIFICATIONS» [ bar = 00 kpa] Pneumatic base ISO 58 (CNOMO E06.6.0N, size 5) Connection Subbase Response time 8-5 ms fluids ( ) temperature range (TS) seal materials ( ) air or inert gas filtered at 50 µm, lubricated or not () LP, LP, LP: see "electrical characteristics" table -0 C to +50 C (LP) () -5 C to +60 C (LP) () -5 C to +60 C /+50 C (LP) () NBR (nitrile) FPM (fluoroelastomer) 00075GB-0/R0 MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body PARA Internal parts POM, PET, stainless steel and brass Seals NBR (disc), FPM (others) Pneumatic interface seal TPE OTHER MATERIALS Coil (5) Only available in 4 V AC/DC and 5 V AC. ~ = with connector --A --D without connector --L --P Thermoplastic PET ELECTRICAL CHARACTERISTICS Coil insulation class F Connector Spade plug (cable Ø 4-6 mm) Connector specification DIN 4650, 9,4 mm, form C or ISO 57 / DIN 4650, 8 mm, form C Electrical safety IEC 5 Electrical enclosure protection Moulded IP65 (EN 6059) Standard voltages DC (=) : 4V (Other voltages on request) AC (~) : 4V - 5V - 0V / 50-60 Hz power ranges coils power ratings ( ) operator voltages (V) inrush ~ holding ~ hot/cold = PNEUMATIC-ELECTRIC interface (available on request) PNEUMATIC CNOMO interface (standard) 0 5 LP 058 048 059 049 0 0 LP 05-05 - 0 LP 054 044 055 045 0 6 LP 057-058 - When ordering, please specify in addition to the basic catalogue number: the type of current: voltage / frequency + the version: with or without connector to be inserted after the basic catalogue number ambient temperature range (4) (TS) ~ = (VA) (VA) (W) (W) ( C) LP - 4 - - - 0,5 / 0,55-0 to +50 LP 4-5 4,4,, /, -5 to +60 LP 0 4,,6,5 /,65-5 to +60 (~)/+50 (=) () type () () Refer to the dimensional drawings on the following page.. () With LED, see page 96 (4) For joinable subbase mounting, see page 96. SPECIFICATIONS (NO and U, following page) orifice size at 6 bar l/min (ANR) flow coefficient Kv operating pressure differential (bar) power ranges 0 ( ) Nominal power ratings of versions without LED indicator and electrical protection. impulse For versions with LED indicator and electrical protection, add: 0,5 W with DC (=) 0,4 W / VA with AC (~) basic catalogue number manual operator maintained 9,4 mm 8 mm 9,4 mm 8 mm (mm) min. max. (PS) ~ ~ NC - Normally closed (Without LED and protection) 0,6 0 0, 0,6 0 8 LP - 006 - - 007-0 0 LP 009 0009 00 000 0,8 7 8 0, 0,5 0 8 LP 0 00 0 00, 5 0,5 0,50 0 5 LP 08 008 09 009,5 9 5 0,50 0,56 0 0 LP 0 00 0 00 0 LP 04 004 05 005 0 6 LP 07 007 08 008 NC - Normally closed (With LED and protection) (5) 0,6 0 0, 0,6 0 0 LP 0509 0409 050 040 0,8 7 8 0, 0,5 0 8 LP 05 04 05 04, 5 0,5 0,50,5 9 5 0,50 0,56 Examples: with connector 4V DC : 009--D 4V DC without connector 4V DC : 009--P 4V DC 9
MINI-SOLENOID VALVES SERIES 0 SPECIFICATIONS: NO, U OPTIONS AND ACCESSORIES 56 orifice size Seals and disc made of FPM (fluoroelastomer) Versions without manual operator and Uv (Universal vacuum): contact us Version with pneumatic-electric interface Version V DC, LP, connector DIN 4650, 9,4 mm, industry standard B Connector ISO 57 / DIN 4650, 8 mm, form C: - standard: catalogue number 880 - with cable m length: catalogue number 8804 Connector EN 750-80 industry standard form C (9,4 mm): - standard: catalogue number 88458 - with cable m length: catalogue number 884567 Explosionproof enclosures for use in zones 0/0-/-/, categories -- to ATEX Directive 94/9/EC (see Explosionproof solenoids section) INSTALLATION The solenoid valves can be mounted in any position without affecting operation Solenoid valve supplied with mounting screws and mounting pad seal(s) Installation/maintenance instructions are included with each valve DIMENSIONS (mm), WEIGHT (kg) TYPE 0 IEC 5 / DIN 4650 IP65 connection Subbase mounting surface: ISO 58 function (CNOMO E06.6.0N, size 5) 47 4 at 6 bar l/min (ANR) 4,5 0 flow 50 coefficient Kv 90 Manual operator location mounting screw M x 0 8, Version with LED and electrical protection operating pressure differential (bar) 9,7 5 universal power ranges NC P O E NO E O P MIX P O P SEL O P O P: Pressure O: Outlet E: Exhaust impulse basic catalogue number manual operator maintained 9,4 mm 8 mm 9,4 mm 8 mm (mm) min. max. (PS) ~ ~ NO - Normally open (Without LED and protection) 0,8 0 7 0,6 0,0 0 8 LP 00 000 0 00 0 0 LP 0 00 04 004 8 0,5 0,5 0 5 LP 06 006 07 007 0 8 LP 09 009 040 0040,5 5 9 0,56 0,50 0 LP 04 004 04 004 0 6 LP 045 0045 046 0046 NO - Normally open (With LED and protection) (5) 0,8 0 7 0,6 0,0 0 8 LP 050 040 05 04 0 0 LP 05 04 054 044 8 0,5 0,5 0 5 LP 056 046 057 047 0 8 LP 059-0540 -,5 5 9 0,56 0,50 0 LP 054 044 054 044 0 6 LP 0545-0546 - U - universal (Without LED and protection) 0,8 7 0 0,0 0,6 0 6 LP 048 0048 049 0049 U - universal (With LED and protection) (5) 0,8 7 0 0,0 0,6 0 6 LP 0548 0448 0549 0449 (5) Only available in 4 V AC/DC and 5 V AC. When ordering, please specify in addition to the basic catalogue number: the type of current: voltage / frequency + the version: with or without connector ~ = with connector --A --D without connector --L --P to be inserted after the basic catalogue number 9 Examples: with connector 4V DC : 00--D 4V DC without connector 4V DC : 00--P 4V DC,8,8 9,7 5 weight () 0,047 8, () with standard connector. x Ø x Ø,5 00075GB-0/R0
MINI-SOLENOID VALVES ISO 58 (CNOMO, size 5) interface direct operated, pad mounting body connection M or with cable ends NC / Series 0 FEATURES Compact, monobloc solenoid pilot valve with M connector or cable ends Version with integrated LED indicator and electrical protection. LED indicator visible from sides The solenoid valves satisfy all relevant EC directives GENERAL Differential pressure See «SPECIFICATIONS» [ bar = 00 kpa] Pneumatic base ISO 58 (CNOMO E06.6.0N, size 5) Connection Subbase Response time 8-5 ms fluids ( ) temperature range (TS) seal materials ( ) air or inert gas filtered at 50 µm, lubricated or not -5 C to +60 C (LP) () NBR (nitrile) FPM (fluoroelastomer) () LP: see "electrical characteristics" table 00075GB-0/R0 MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body PAA Internal parts POM, PET, stainless steel and brass Pneumatic interface seal TPE OTHER MATERIALS Coil Thermoplastic PET ELECTRICAL CHARACTERISTICS Coil insulation class F Connection Connector M or cable ends Electrical safety IEC 5 connector M CNOMO E0.6.50.N cable ends EN 6070 Electrical enclosure protection Moulded IP67 (EN 6059) Standard voltages DC (=) : 4V power ranges coils power ratings ( ) operator ambient voltages inrush holding hot/cold temperature (V) ~ ~ = range () (TS) type () ~ = (VA) (VA) (W) (W) ( C) LP - 4 - - -,5 /,5-5 to +60 0-0-0 () () Refer to the dimensional drawings on the following page. For joinable subbase mounting, see page 96. SPECIFICATIONS ( ) Nominal power ratings of standard versions (with LED indicator and electrical protection) flow orifice operating pressure basic catalogue number at 6 bar coefficient power size differential (bar) l/min (ANR) Kv ranges manual operator (mm) min. max. (PS) impulse maintained NC - Normally closed, connection M + LED and protection 0,6 0 0, 0,6 0 0 LP 009 00 0,8 7 8 0, 0,5 0 8 LP 0 0, 5 0,5 0,50 0 5 LP 08 09,5 9 5 0,50 0,56 0 LP 04 05 NC - Normally closed, cable ends + LED and protection 0,6 0 0, 0,6 0 0 LP 009 00 0,8 7 8 0, 0,5 0 8 LP 0 0, 5 0,5 0,50 0 5 LP 08 09,5 9 5 0,50 0,56 0 LP 04 05 When ordering: with connector without connector complete Examples: M with connector M without connector cable ends M --D --P cable --D : 009--D : 009--P : 009--D to be inserted after the basic catalogue number 9
MINI-SOLENOID VALVES SERIES 0 OPTIONS AND ACCESSORIES Seals and disc made of FPM (fluoroelastomer) Versions without manual operator, NO (Normally Open), U (Universal) and Uv (Universal vacuum): contact us Version with pneumatic-electric interface Straight M connector: - with 5 m cable length: catalogue number 880 Explosionproof enclosures for use in zones 0/0-/-/, categories -- to ATEX Directive 94/9/EC (see Explosionproof solenoids section) INSTALLATION The solenoid valves can be mounted in any position without affecting operation Solenoid valve supplied with mounting screws and mounting pad seal(s) Installation/maintenance instructions are included with each valve DIMENSIONS (mm), WEIGHT (kg) TYPE 0 IEC 5 Connection M IP67 TYPE 0 IEC 5 / Straight M connector, 5 m cable length IP67 47 47 4,8,8 8, 9,7 4,5 0 5 9 7 4,5 0 75 8, 9,7 5 7 Manual operator location. mounting screw M x 0 M () () () weight cable ends 0,049 0,88 0,040 () Without connector () With connector connection function NC P O E P: Pressure O: Outlet E: Exhaust 47 4,5 TYPE 0 IEC 5 Cable ends 0, m length IP67 0,5 8, 94 9,7 5 Subbase mounting surface: ISO 58 (CNOMO E06.6.0N, size 5),8,8 9,7 5 8, x Ø x Ø,5 00075GB-00/R0
MINI-SOLENOID VALVES SERIES 0 DIMENSIONS (mm), WEIGHT (kg) Single subbase Aluminium or brass 60 45 0 0 x Ø M5 5 9 5 65 90 5,5 5 A Mounting: holes M, depth 4,5 Orifice () can be connected on the left or on the right of the subbase. material catalogue number weight () aluminium 88600 0,0 brass 00000 0,04 () subbase alone Adapter CNOMO size 0 (only for NC version) Aluminium 6 48 90 A Mounting: screws M4 x 0 (supplied) 6,5 0 60 6 7,5 9 4,5 catalogue number weight () 88600 0,08 () adapter alone Joinable subbases Aluminium 00075GB-008/R0,5 Ports and : G/8,5 8,5 Port : coupling for 4mm OD tube 4,5 Fixing hole Ø, ( for 4x ; for x),5 Fixing hole M, depth 8 ( for 4x ; for x) Mating surface blanking plates (option) 4 TS5 DIN rail (not supplied) 5 Clip for DIN rail mounting (option) 4 5 8,5 7 7 7 8,58,5 7 8,5 68 (4x) L 4 (x) 9 0 50 catalogue number x subbases L weight () 5500564 x - 0,076 5500565 4 4x - 0,48 5500566 6 4x + x 4 0,6 5500567 8 4x + 4x 48 0, 5500568 0 4x + 4x + x 8 0,89 5500569 4x + 4x + 4x 6 0,466 () subbases alone x = place for mini-solenoid valves. plugs R/8 supplied. 58 95
MINI-SOLENOID VALVES SERIES 0 OPTIONS AND ACCESSORIES Additional subbase with places (with seals): catalogue number 5500570 tie-rods + nuts for a subbase with: 4 places: catalogue number 880075 6 places: catalogue number 880075 8 places: catalogue number 8800754 0 places: catalogue number 8800755 places: catalogue number 8800756 Mounting kit for DIN rail ( clips + screws + washers): catalogue number 8800757 Mating surface blanking plate: catalogue number 8800 AMBIENT TEMPERATURE RANGES current type DC (=) AC (~) power range () Voltage: -5% / +0% () Voltage: -5% / +0% inrush/ holding (VA) ~ power coil hot/cold (W) = version LP () - 0,5/0,55 standard -0 C ; +50 C -0 C ; +50 C - /, standard -5 C ; +60 C LP () -5 C ; +60 C -,5/,5 LED + protection -5 C ; +40 C - /,65 standard -5 C ; +50 C -5 C ; +40 C LP () -,5/,8 LED + protection -5 C ; +40 C -,4/, - standard LP () -5 C ; +60 C -5 C ; +40 C,8/,6 - LED + protection,/,6 - standard -5 C ; +60 C -5 C ; +40 C LP (),5/ - LED + protection -5 C ; +50 C - 96 00075GB-00/R0
MINI PIEZO-VALVES PIEZOTRONIC direct operated ISO 58 (CNOMO, size 5) interface pad mounting body, M5, G/8 or instant fittings subbase NC NO /-/ Series 60 004GB-04/R0 SPECIFICATIONS FLUIDS : air or inert gas, filtered at 5 µm, condensate free dow point -0 C PRESSURE : 0 to 4 or 8 bar MAX. ALLOWABLE PRESSURE (MAP) : 8 bar FLUID TEMPERATURE : 0 C to +60 C AMBIENT TEMPERATURE : 0 C to +60 C STORAGE TEMPERATURE : -40 C to +60 C BASE : ISO 58 (CNOMO E06.6.0N, size5) or ISO 58 (CNOMO E06.05.80, size 0) with adapter MOUNTING : on subbases ØM5, G/8 or instant fittings SERVICE LIFE : > 0 9 cycles at 6 bar MOUNTING POSITION : all ELECTRICAL CONNECTION version with pins CONSTRUCTION Non polarized solenoid valve Body : synthetic material (PPS) Internal parts : piezo ceramics (+/-) without Subbase : brass, polyamide, zinc diecast function (+/-) ELECTRICAL CHARACTERISTICS Sealings Manual override : nitrile (NBR) : without or impulse type Voltage (Maximum ripple : 0 %) ACCESSORIES 6 0,086 0 8 6,5 () 0, 0 4 6 0,086 0 8 6,5 () 0, 0 4 7 0,0 8 6 0,086 8 Visual indicator LED (Caution, consumption 0,5W and voltage 4V max.) Plug size 5 with m cable Power consumption at 4 V inrush hold Plug size 5 with built-in visual indicator (LED), with m cable Protection degree 50 ms (DC) 4 to 70 V AC/DC ±0% 0,6 W 0,007 W 70 ms (AC) IP 65 Switching current = 5 ma/0ms SPECIFICATIONS / NC / NO / NC / NO Symbols Functions at 6 bar l/min (ANR) Flow Coefficient Kv (M) Manual operator: X : without : Impulse () Flow at 4 bar in l/min (ANR) Allowable differential pressure ( p in bar) min. Response time max. SUBBASES: Single subbase with lateral connection Ø M5 - cat no.: 88600 Single subbase - connection G/8 - cat no.: 500047 Joinable subbase - connection G/8 - cat no.: 500048 OPTION : Minivalve operated, intrinsically safe EEx ia, V - 4V DC DESCRIPTION catalogue number 4V =/~ max. Adapter for mounting PIEZOTRONIC on base ISO 58 (CNOMO E06.05.80, size 0) (M) Version with wires Non polarized solenoid valve Electrical connection Spade plug size 5 connector, DIN 4650, 9,4 mm, industry standard B, rotatable by 90, Option : with wires, length m catalogue number PIEZOTRONIC with pins PIEZOTRONIC with standard connector with wires, m long X 6000065 600005 600007 60000 X 6000067 600007 600007 60000 X 6000066 600006 600007 60000 X 6000068 600008 6000074 600004 X 600006 60000 6000069 600009 X 6000064 600004 6000070 600000 88040 884567 884580 88600 97
MINI PIEZO-VALVES PIEZOTRONIC - SERIES 60 DIMENSIONS AND WEIGHTS MINI PIEZO-VALVE WITH STANDARD CONNECTOR Weight : 4 g without connector 4 g with connector MINI PIEZO-VALVE ON SINGLE SUBBASE 88600 Weight : 45 g 6 48 6 5 48 x M M x 0 4,5 8,5 5*,5 9,7 5 0 0 9 x M5 5 66* 5,5 5 8 ASSEMBLY WITH LED INDICATOR (accessory, rotatable x80 ) 5 MOUNTING FACE Subbase for mini piezo-valve ISO 58 (CNOMO E06.6.0N, size5) x Ø,5 x M,5,8,8 6, 9,7 5 Single subbase connection : Outlet () can be connected on the left or on the right of subbase ; closed unused port with a Ø M5 plug (supplied). Connector size 5 rotatable by 90 Manual operator by impulse ( ) + 0 mm for clearance MINI VALVE + Intermediate subbase (Adapter CNOMO size 0 : cat no.: 88600) Total weight : 5 g 6 5* 69 54 6,5 88600 + 0 mm for clearance Connector rotatable x 90 CM6 (Pg 7p) Mounting screws CM4x0 6 7,5 4,5 9 Exhaust () (not-collectable) Outlet () Pressure () 004GB-008/R0 98
SOLENOID VALVES direct operated, quick switching manifold mount, pad-mount or inline version, or push-in hose connection / NC / NC / / Series RB FEATURES Miniature solenoid valves for medical and gas analysers and leak detectors Suitable for the control of gases The valves have a service life of more than 00 million cycles when used with inert gas Short response times Easy to integrate thanks to the valve s small size Available in a variety of versions for a wide range of applications: threaded connections or pad-mount for installation on multiple manifolds Vacuum application up to -0. bar Low power consumption and light weight offers extended battery life for portable devices Multiple body configurations to suit all application needs GENERAL Differential pressure Response time See "SPECIFICATIONS" [ bar =00 kpa] < 0 ms fluids ( ) temperature range (TS) seal materials ( ) air, inert gases FPM (fluoroelastomer) 0 C to +60 C (filtered 0 µm) NBR (nitrile) MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body PBT, brass Internal parts Stainless steel Seat PBT, brass Seals FPM, NBR ELECTRICAL CHARACTERISTICS Coil insulation class B (0 C) Connection Cable ends 6 AWG or circuit board mount Electrical safety IEC 5 Electrical enclosure protection IP0 (EN 6059) Standard voltages DC (=) : 5V - V - 4V power ratings operator prefix inrush holding hot/cold ambient temperature raplacement coil option ~ ~ = range (TS) (VA) (VA) (W) (W) (C ) - - - - 0,5 /,0 /.0 0 to +60 - - () Refer to the dimensional drawings on the following page. / NC manifold mount / NC line mount 0045GB-04/R0 / NC pad mount / NC push-in hose connection 99
SPECIFICATIONS 00 pipe size orifice size (mm) / NC - Normally closed 0- UNF Stud Manifold Mount, Brass (M) 0- UNF Female In-Line, Brass (L),7 mm Push-in Hose Connecton PBT (B) Pad Mount, PBT (F) HOW TO ORDER catalogue no. voltages 4 = 5 VDC 6 = VDC 7 = 4 VDC electrical connection H = cable ends P = PCB pins (circuit board) flow coefficient Kv operating pressure differential (bar) min, max, (PS) air, inert gas ( ) SOLENOID VALVES SERIES RB power coil (W) (m /h) (l/min) catalogue number 0,8 0,0 0,5-0,9,4 0,5 RLM0xx0x 0,8 0,0 0,5-0,9 6,9,0 RHM0xx0x, 0,047 0,78-0,9,7 0,5 RLM0xx50x, 0,047 0,78-0,9,4,0 RMM0xx50x, 0,047 0,78-0,9 6,9,0 RHM0xx50x,0 0,07,6-0,9,7,0 RHM0xx80x 0,8 0,0 0,5-0,9,4 0,5 RLL0xx0x 0,8 0,0 0,5-0,9 6,9,0 RHL0xx0x, 0,047 0,78-0,9,7 0,5 RLL0xx50x, 0,047 0,78-0,9,4,0 RML0xx50x, 0,047 0,78-0,9 6,9,0 RHL0xx50x,0 0,07,6-0,9,7,0 RHL0xx80x 0,8 0,0 0,5-0,9,0 0,5 RLB0xx0x 0,8 0,0 0,5-0,9,4,0 RMB0xx0x 0,8 0,0 0,5-0,9 6,9,0 RHB0xx0x, 0,047 0,78-0,9 0,7 0,5 RLB0xx50x, 0,047 0,78-0,9,4,0 RMB0xx50x, 0,047 0,78-0,9 4,8,0 RHB0xx50x,0 0,07,6-0,9,7,0 RHB0xx80x 0,8 0,0 0,5-0,9,0 0,5 RLF0xx0x 0,8 0,0 0,5-0,9,4,0 RMF0xx0x 0,8 0,0 0,5-0,9 6,9,0 RHF0xx0x, 0,047 0,78-0,9 0,7 0,5 RLF0xx50x, 0,047 0,78-0,9,4,0 RMF0xx50x, 0,047 0,78-0,9 4,8,0 RHF0xx50x,0 0,07,6-0,9,7,0 RHF0xx80x 0-DIGIT PRODUCT CODE RLM0 x x 0 x seal materials B = NBR V = FPM O = Oxygen service (FPM) catalogue no. Ordering example: RLM04H0B = -way (normally closed), 5 VDC, manifold mount with 0,8 mm orifice, 0,5 watt, cable ends, NBR seals 0045GB-0/R0
0045GB-05/R0 SPECIFICATIONS pipe size OPTIONS Other voltages Other seal materials Other electrical connectors Oxygen service Other pipe connections INSTALLATION orifice size (mm) flow coefficient Kv operating pressure differential (bar) The solenoid valves can be mounted in any position without affecting operation Threaded solenoid valves have mounting holes in body Pad-mount valves and o-ring seals for multiple manifolds min, max, (PS) air, inert gas ( ) power coil (W) catalogue number (m /h) (l/min) / NC - Normally closed 0,8,0 0,0 0,5-0,9,4 0,5 RLMxxx4x 0- UNF Stud 0,8,0 0,0 0,5-0,9 6,9,0 RHMxxx4x,, 0,047 0,78-0,9,0 0,5 RLMxxx55x Manifold Mount,,, 0,047 0,78-0,9,4,0 RMMxxx55x Brass (M),, 0,047 0,78-0,9 6,9,0 RHMxxx55x,0, 0,07 / 0,047,6 / 0,78-0,9,7,0 RHMxxx85x 0- UNF Female In-Line, Brass (L),7 mm push-in hose PBT (B) Pad Mount, PBT (F) HOW TO ORDER catalogue no. port style B =,7 mm push-in hose connection F = 0- UNF female voltages 4 = 5 VDC 6 = VDC 7 = 4 VDC electrical connection H = cable ends P = PCB pins (circuit board) 0,8,0 0,0 0,5-0,9,4 0,5 RLLxxx4x 0,8,0 0,0 0,5-0,9 6,9,0 RHLxxx4x,, 0,047 0,78-0,9,0 0,5 RLLxxx55x,, 0,047 0,78-0,9,4,0 RMLxxx55x,, 0,047 0,78-0,9 6,9,0 RHLxxx55x,0, 0,07 / 0,047,6 / 0,78-0,9,7,0 RHLxxx85x 0,8,0 0,0 0,5-0,9,0 0,5 RLBxxx4x 0,8,0 0,0 0,5-0,9,4,0 RMBxxx4x 0,8,0 0,0 0,5-0,9 6,9,0 RHBxxx4x,, 0,047 0,78-0,9 0,7 0,5 RLBxxx55x,, 0,047 0,78-0,9,4,0 RMBxxx55x,, 0,047 0,78-0,9 4,8,0 RHBxxx55x,0, 0,07 / 0,047,6 / 0,78-0,9,7,0 RHBxxx85x 0,8,0 0,0 0,5-0,9,0 0,5 RLFxxx4x 0,8,0 0,0 0,5-0,9,4,0 RMFxxx4x 0,8,0 0,0 0,5-0,9 6,9,0 RHFxxx4x,, 0,047 0,78-0,9 0,7 0,5 RLFxxx55x,, 0,047 0,78-0,9,4,0 RMFxxx55x,, 0,047 0,78-0,9 4,8,0 RHFxxx55x,0, 0,07 / 0,047,6 / 0,78-0,9,7,0 RHFxxx85x 0-DIGIT PRODUCT CODE RLM x x x 0 x SOLENOID VALVES SERIES RB seal materials B = NBR V = FPM O = Oxygen service (FPM) catalogue no. Ordering example: RLMB7P4V = -way (normally closed), 4 VDC, port with push-in hose connection, manifold mount with 0,8 mm orifice, 0.5 watt, PCB pins, FPM seals 0
SOLENOID VALVES SERIES RB DIMENSIONS (mm), WEIGHT (kg) - and -way pad mount solenoid valve x Ø, mm mounting holes (for screws Mx0) 6 AWG PTFE coated lead wires 04,8 mm long Hose I.D., mm 9. 7.9 5. 7.8 6.5 44.0 5.05 Port Port Port (if applicable) 4. 7. - and -way solenoid valve with push-in hose connection 0 Square pins 0,6 mm x 0,6 mm 5.. x Ø, mm mounting holes (for screws Mx0) Port Port 4. 7.9 44.0 5.05 0. 4.4 Port (if applicable) Hose I.D., mm front pins for mounting only rear pins for mounting and electrical connection 0045GB-0/R0
SOLENOID VALVES SERIES RB DIMENSIONS (mm), WEIGHT (kg) - and -way line mount solenoid valve 6 AWG PTFE coated lead wire 04,8 mm long 6.6.7 6.4 x 0- UNF port & port 9. 7.5 Port 9. Mounting holes x 6- UNC 4,8 mm deep 4. - and -way manifold mount solenoid valve 0045GB-04/R0 Screw-in mounting pattern Ø0,6±0, max. Ø,5+0,05 M5-5 deep Port x Ø, mm for hook spanner wrench 0- UNF mounting stud 4.8 5.6 Port (if applicable) 6 AWG PTFE coated lead wire 04,8 mm long 9. 0
SOLENOID VALVES SERIES RB 04
SOLENOID VALVE direct operated, quick switching threaded or screw-in type body M5 NC / Series S FEATURES Miniature solenoid valves for medical and gas analysers and leak detectors Suitable for the control of gases Short response times Compact size for easy integration into systems Available in a variety of versions for a wide range of applications: threaded or screw-in type valve bodies for installation on multiple manifolds Approved to UL standards Vacuum application up to -0.9 bar GENERAL Differential pressure Response time See "SPECIFICATIONS" [ bar =00 kpa] < 0 ms fluids ( ) temperature range (TS) seal materials ( ) air, inert gases (filtered 0 µm) 0 C to +60 C FPM (fluoroelastomer) MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body Stainless steel Internal parts Stainless steel Seals FPM (fluoroelastomer) [EPDM (ethylene-propylene), contact us] ELECTRICAL CHARACTERISTICS Coil insulation class B Connection Spade plug or cable ends AWG 0, length 00 mm Electrical safety IEC 5 Electrical enclosure protection IP40 (EN 6059) Standard voltages DC (=) : V - 4V power ratings operator prefix inrush holding hot/cold ambient temperature raplacement coil Typ option ~ ~ = () range (TS) (VA) (VA) (W) (W) (C ) - - - -,5 /,5-0 to +60 - - 0 () Refer to the dimensional drawings on the following page. Function NC, threaded body 0040GB-04/R0 SPECIFICATIONS pipe size orifice size flow coefficient kv operating pressure differential (bar) power coil (W) Function NC, screw-in type body catalogue no. max. min. air and gases ( ) threaded body screw-in type body (mm) (m /h) (l/min) ~ = ~ = xx : see HOW TO ORDER NC - Normally closed 0,75 0,06 0,6-0,9-7 -,5 HSMLxx00V HSMMxx00V M5 0,05 0,4-0,9-7 -,5 HSMLxx0V HSMMxx0V 0,058 0,97-0,9 -,5 -,5 HSMLxx50V HSMMxx50V HOW TO ORDER catalogue no. voltages 6 = VDC 7 = 4 VDC electrical connection F = Spade plug H = cable ends 0-DIGIT PRODUCT CODE HSML x x 00 V seal materials V = FPM catalogue no. 05
SOLENOID VALVES SERIES S OPTIONS Seals made from EPDM (ethylene-propylene) (contact us) Oxygen service INSTALLATION The solenoid valves can be mounted in any position without affecting operation Threaded solenoid valves have mounting holes in body Screw-in type valves and o-ring seals for multiple manifolds DIMENSIONS (mm), WEIGHT (kg) HSMLxx00V / HSMLxx0V / HSMLxx50V HSMLxx00V / HSMLxx0V / HSMLxx50V HSMMxx00V / HSMMxx0V / HSMMxx50V HSMMxx00V / HSMMxx0V / HSMMxx50V M5 / 0- UNF-B ( ) ( ) Supplied with 0- UNF-B male thread compatible with M5 female counter-thread screw-in mounting pattern mounting holes Ø Mx0,5 Mounting with hook spanner wrench DIN 80B 06 connection type catalogue no. A B C D E F G weight threaded body screw-in type body HSMLxx00V/HSMLxx0V/HSMLxx50V HSMLxx00V/HSMLxx0V/HSMLxx50V HSMMxx00V/HSMMxx0V/HSMMxx50V HSMMxx00V/HSMMxx0V/HSMMxx50V Ø0,6±0, max. Ø,5+0,05 9,05 - - 4,7 6,5,7 9, 0,059 9,05 9,6 4,8 - - - - 0,05 M5-5 deep 0040GB-04/R0
SOLENOID VALVE direct operated, quick switching threaded or screw-in type body M5 NC / Series S FEATURES Miniature solenoid valves for medical and gas analysers and leak detectors Suitable for the control of gases Short response times Compact size for easy integration into systems Available in a variety of versions for a wide range of applications: threaded or screw-in type valve bodies for installation on multiple manifolds Approved to UL standards Vacuum application up to -0.9 bar GENERAL Differential pressure Response time See "SPECIFICATIONS" [ bar =00 kpa] < 0 ms fluids ( ) temperature range (TS) seal materials ( ) air, inert gases (filtered 0 µm) 0 C to +60 C FPM (fluoroelastomer) MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified Body Stainless steel Internal parts Stainless steel Seals FPM (fluoroelastomer) [EPDM (ethylene-propylene), contact us] ELECTRICAL CHARACTERISTICS Coil insulation class B Connection Spade plug or cable ends AWG 0, length 00 mm Electrical safety IEC 5 Electrical enclosure protection IP40 (EN 6059) Standard voltages DC (=) : V - 4V power ratings operator prefix inrush holding hot/cold ambient temperature raplacement coil type option ~ ~ = () range (TS) (VA) (VA) (W) (W) (C ) - - - -,5 /,5-0 to +60 - - 0 () Refer to the dimensional drawings on the following page. Function NC, threaded body 004GBGB-04/R0 SPECIFICATIONS pipe size orifice size flow coefficient Kv operating pressure differential (bar) power coil (W) Function NC, screw-in type body catalogue no. max. (PS) min. air and gases ( ) threaded body screw-in type body (mm) (m /h) (l/min) ~ = ~ = xx : see HOW TO ORDER NC - Normally closed 0,75 0,06 0,6-0,9-7 -,5 HSMLxx00V HSMMxx00V M5 0,05 0,4-0,9-7 -,5 HSMLxx0V HSMMxx0V 0,058 0,97-0,9 -,5 -,5 HSMLxx50V HSMMxx50V HOW TO ORDER catalogue no. voltages 6 = VDC 7 = 4 VDC electrical connection F = Spade plug H = cable ends 0-DIGIT PRODUCT CODE HSML x x 00 V seal materials V = FPM catalogue no. 07
SOLENOID VALVES SERIES S OPTIONS Seals made from EPDM (ethylene-propylene) (contact us) Oxygen service Other pipe connections (0- UNF-B) INSTALLATION The solenoid valves can be mounted in any position without affecting operation Threaded solenoid valves have mounting holes in body Screw-in type valves and o-ring seals for multiple manifolds DIMENSIONS (mm), WEIGHT (kg) HSMLxx00V / HSMLxx0V / HSMLxx50V HSMLxx00V / HSMLxx0V / HSMLxx50V HSMMxx00V / HSMMxx0V / HSMMxx50V HSMMxx00V / HSMMxx0V / HSMMxx50V / M5 screw-in mounting pattern mounting holes Ø Mx0,5 Mounting with hook spanner wrench DIN 80B 08 connection type catalogue no. A B C D E F G weight threaded body screw-in type body HSMLxx00V/HSMLxx0V/HSMLxx50V HSMLxx00V/HSMLxx0V/HSMLxx50V HSMMxx00V/HSMMxx0V/HSMMxx50V HSMMxx00V/HSMMxx0V/HSMMxx50V Ø0,6±0, max. Ø,5+0,05 9,05 - - 4,7 6,5,7 9, 0,059 9,05 9,6 4,8 - - - - 0,05 M5-5 deep 004GBGB-04/R0
SOLENOID VALVE flat-spring technology, precise response time, quick switching, Ø 5 mm, pad-mount body / NC / NC / / Series 065 FEATURES Miniature solenoid valve for respirators, medical analyzers, gas analyzers and control units, as well as for use as a pilot valve. RoHS compliant. New flat-spring technology enables - short response times and their precise adjustment - very low switching noise - exceptional long service life Suitable for oxygen service Easy to integrate thanks to the valves small size. Pad-mount for installation on multiple manifolds. Vacuum application up to 0, bar abs. All connections of the / way valve are contactable via the flange. GENERAL Differential pressure Maximum viscosity Response time Internal volume See SPECIFICATIONS [ bar =00 kpa] 0 cst (mm /s) < 0 ms 50 µl (couplings not included) fluids ( ) temperature range (TS) seal materials ( ) air, inert gases, oxygen (filtered 50 µm) 0 C to + 60 C FPM (fluoroelastomer) 0060GB-05/R0 MATERIALS IN CONTACT WITH FLUID ( ) Ensure that the compatibility of the fluids in contact with the materials is verified. Body Stainless steel Plugnut Stainless steel Flat-spring Stainless steel Seat and housing base PPS Seals FPM (other materials: contact us) ELECTRICAL CHARACTERISTICS Coil insulation class F Connection Cable leads AWG 6/7, 80mm length Electrical safety IEC 5 Electrical enclosure protection IP40 (EN 6059) Standard voltages DC (=) : V, 4V Power W at 0 C Duty cycle 00% at ambient temperature 0 C to 60 C SPECIFICATIONS function / NC / NC ORDERING orifice size flow coefficient kv operating pressure differential (bar) power coil catalogue number (mm) (m /h) (l/min) min. max. (W) 0,6 0,00 0,59 0 9 R065AL0V00xx, 0,05 0,580 0 R065A4L0V00xx 0,6 0,00 0,59 0 5 R065A4L0V00xx, 0,04 0,404 0, R065A44L0V00xx According to table SPECIFICATIONS R065AL0V00 F Voltage F = 4 VDC F = VDC / NC function / NC function 09