O w n e r / O p e r a t o r M a n u a l HXG272E
Safety Warnings This machine is designed to produce very high pressure at the outlet nozzle. High pressure from spray or leaks can penetrate skin and cause serious injury or death. Never direct the spray towards any part of the body. Never try to stop or deflect leaks with your hand. Avoid contact with engine muffler. Never operate machinery while under the influence of alcohol. Service Warnings Modifications or alterations performed on equipment may void warranty. Replace damaged hoses or fittings. Replacement parts must meet or exceed original factory specifications to ensure safe operation. Do not modify engine parts or settings. Operating machine with either water or oil leaks will void warranty. Do not operate with engine in idle position. Do not leave machine running in bypass (trigger off) for longer than 2 minutes. Failure to do so will destroy pump seals. Inlet water temperature must not exceed 160 Degrees Fahrenheit (71 Degrees Celsius). Ensure you have sufficient water supply. To check water supply, collect water from outlet for one minute. The amount collected must exceed the water volume of your pump. Pump volume is measured in GPM (gallons per minute). Refer to model tag on frame for specifications. Do not allow water to freeze inside pressure washer equipment. (Fill pump fluid end with windshield washer antifreeze when storing in freezing conditions.) Pump must be fed with a minimum pressure of 15 PSI and a maximum pressure of 80 PSI. When feeding pump from a tank, ensure that the tank water level is higher than the pump inlet. (This pump is not designed to draw water) Pump oil must be changed after first 50 hours and every 250 thereafter. Use PP-961150C (15W50 Synthetic). Pump oil capacity: 4.1 oz. / 121 ml (do not overfill. If oil level is more than half way inside pump crackcase it will pump itself out top vent) Do not operate pressure washer without a water inlet screen or filter. Dirty water will destroy seals and valves. To ensure warranty, please return enclosed warranty document with signature. 2
Before You Start Getting Started Engine Oil Ensure oil level reads to top of dipstick. (Use10W-30 engine oil). Check Pump Oil - The pump has it's own oil separate from the Engine. It's pre filled at factory. Pump holds 4.1oz Synthetic 15W50 oil only. STORM JET P/N: PP-961150C. Do not overfill. Gasoline - Use regular unleaded gasoline. Size your water supply hose - Use no smaller than a 5/8 I.D. hose to feed pump. Hose must be free of kinks and leaks. Flush water inlet hose before attaching to pump. Attach water inlet hose and pressure hose onto pump. Attach gun/wand assembly to pressure hose and remove nozzle from end of wand. Adjust engine throttle arm to middle position and apply choke. Turn water on, and pull trigger on gun. Inspect for leaks while allowing air to bleed from line. With water flowing out of gun, start engine and continue flushing for 10 seconds. Turn choke off and adjust throttle to full throttle position (3500 RPM factory setting). Release gun and install nozzle into wand to begin washing. Getting Soap Your machine is equipped with a low pressure (downstream) soap injector (Approx. 400 PSI). The pressure is reduced automatically by installing the black soap nozzle. Dispense soap as follows: 1. Place clear vinyl tube with filter attached into soap container. 2. Ensure soap metering valve is adjusted to a mid-range setting (if equipped See Figure A). 3. Install black soap nozzle into wand assembly, pull trigger and begin dispensing soap. 4. Rinse fresh water through valve after each use. This will prevent soap from drying and plugging up the valve. Adjust metering valve according to soap requirements. Soap will automatically stop drawing if colored high pressure tips are in use. HG252/292E Models HGP Models Figure A Nozzles All spray tips provided will produce the same pressure (except the black soaper tip). The only difference is the angle of spray. Use the following as a rule of thumb. Yellow tip / 15 Deg (spray angle) - Use on tough cleaning jobs that have a hard surface ie, sidewalks or driveways. Green tip / 25 Deg - Use on cleaning your car or vinyl siding White tip / 40 Deg - Use on wood surfaces or under your automobile hood. This tip has the lowest impact of the bunch and will not damage the surface while cleaning. Black tip - Use to get soap only Important The information provided in this manual will help to ensure the safe operation of this equipment. Failure to comply with the enclosed operating instructions will nullify warranty. 3
Pressure Washer Components 10 11 12 13 7 3 16 8 1 19 18 6 5 14 15 17 2 9 4 Item Part # Description Qty 1 HE-GX200-QAPW HONDA 6.5 HP 3/4" SHAFT REC 1 STRT 2 PA-24-GXH2525111H GXH2525 PUMP W/ 3/4" SHAFT 1 (AI) * 3 PP-319011 PW FRAME,RED FOR 10" WH 1 4 06-00010-75 FLAT-FREE WHEEL ASSY, 1 410/350X4X3/4 ID 5 PP-318400 GARD HOSE CONNCT 1 1/2"MNPTX3/4"FGH * 6 PP-318401 GARD HOSE CONNCT GASKET 1 7 PP-721361 GUN W EXT 22M FEMOUT 3/8 PL 1 5KPSI 8 PP-721362 ZN LANCE 24" 22M IN 1/4" QC (AI) 1 Item Part # Description Qty 9 PP-318300 COUPLER BRASS 3/8" FNPT * 1 10 PP-403015 NOZ QD 3.0 ORIF 15 DEG SPRAY 1 11 PP-403025 NOZ QD 3.0 ORIF 25 DEG SPRAY 1 12 PP-403040 NOZ QD 3.0 ORIF 40 DEG SPRAY 1 13 PP-430065 NOZ QD BRASS 30 ORI 65 DEG 1 SPRY * (SOAP) 14 PP-960428 CLEAR HOSE, CHEMICAL 1 INJECTOR, 4' (AI) 15 PP-318605 FILTER PLASTCHEM INJ W * 2 16 PP-5220010 DECAL, STORMJET 1 17 PP-5220013 DECAL, 2700PSI 2.5GPM 1 18 PP-5220020 DECAL, HONDA ENGINE LOGO 2 19 PP-710025 HOSE ASSY, 25' W QD FTGS 4KPSI 248F * 1 4
Gun and Wand Assembly PP-721363 1 2 1 Gun and Wand Assembly PP-719360 2 3 # Part # Description Qty 1 PP-721361 Gun W/Extention, 22mm Coupler 1 2 PP-130201 0-Ring 1 3 PP-721362 Lance Extension, 24 22mm x 1/4 QC 1 4 5 3 Hose Reel Parts # Part # Description Qty 1 PP-318520 Shut-Off Gun 1 2 PP-419360 Zinc plated lance, 36 1 3 PP-319315 Nipple 1 Hose Assembly PP-710025 (25 ) & PP-710050 (50 ) # Part # Description Qty 4 PP-318200 Coupler, 1/4 FNPT 1 5 PP-130201 0-Ring 1 4 3 2 1 # Part # Description 1 PP-69-H100 Replacement Handle 2 PP-69-H202 Swivel replacement for 50 Reel PP-69-H208 PP-69-H480 Swivel replacement for 150 Reel Swivel replacement for 200 Reel 3 PP-718051 Hose Reel Complete with 50 ft hose and Leader Connector hose 4 PP-718050 Hose Reel - No Hose, 50 ft capacity of 3/8" ID hose PP-718150 PP-718200 5 PP-134003 Leader Hose 5 Hose Reel - No Hose, 150 ft capacity of 3/8" ID hose Hose Reel - No Hose, 200 ft capacity of 3/8" ID hose 4 2 3 1 # Part # Description Qty 1 PP-130301 0-Ring, 3/8 Viton 1 2 PP-318301 Coupler 1 3 PP-319310 Nipple 1 4 PP-710025 25 ft. Hose 1 PP-710050 50 ft. Hose 1 PP-710100 100 ft. Hose 1 5
Pump GX2525 1 PP-24-07805 Radial Shaft Seal 1 2 PP-24-06310 Adapting Flange 1 3 PP-24-06294 O-Ring 1 4 PP-24-06300 Rear Bearing 1 5 PP-24-06566 Wobble Plate (GXRH2424) 1 5A PP-24-07882 Shaft Ring 1 6 PP-24-06301 Front Bearing 1 7 PP-24-06289 Spring Disk 3 8 PP-24-06287 Plunger, 16mm 3 9 PP-24-06288 Plunger Spring 3 10 PP-24-06299 Socket Bolt 6 11 PP-24-08192 Gasket 1 12 PP-24-06273 Oil Drain Plug 1 13 PP-24-06282 Crankcase (GXRV) 1 PP-24-06338 Crankcase (GXRH) 1 14 PP-24-08083 Vent Cap (Horizontal Only) 1 15 PP-24-06316 Oil Seal 3 17 PP-24-06292 Spacer 3 18 PP-24-07374 Valve Spring 6 19 PP-24-06267 Guided P-Valve 3 20 PP-24-06290 Pressure Ring 3 21 PP-24-06315 V-Sleeve, 16mm 3 22 PP-24-06296 Discharge Plug 3 14 PP-24-08083 Vent Cap (Horizontal Only) 1 15 PP-24-06316 Oil Seal 3 17 PP-24-06292 Spacer 3 18 PP-24-07374 Valve Spring 6 19 PP-24-06267 Guided P-Valve 3 20 PP-24-06290 Pressure Ring 3 21 PP-24-06315 V-Sleeve, 16mm 3 22 PP-24-06296 Discharge Plug 3 23 PP-24-12007 O-Ring 3 24 PP-24-23507 O-Ring 1 25 PP-24-06710 Seat 1 26 PP-24-06386 6mm S.S. Ball 1 27 PP-24-06385 O-Ring 1 28 PP-24-06384 Plastic Poppet Valve 1 29 PP-24-06382 Spring 1 30 PP-24-06410 O-Ring 1 31 PP-24-06392 Cap 1 35 PP-24-06412 Manifold 1 36 PP-24-06295 Discharge Valve Cone 3 38 PP-24-07910A Triangle O-Ring 1 39 PP-24-06298 Suction Flange 1 40 PP-24-06302 Stud Bolt 4 44 PP-24-06727 Orifice, 1 45 PP-24-06312 O-Ring in Nozzle 1 46 PP-24-07913 O-Ring 1 47 PP-24-06303 Injector Retainer 1 48 PP-24-23009 Spring 1 49 PP-24-23010-0100 Ball 1 50 PP-24-12516-0001 O-Ring 1 51 PP-24-12517 Hose Barb 1 53 PP-24-23422A Thermal Relief Valve 1 54 PP-24-07468 Locktooth Washer 4 55 PP-24-07467 Screws 4 56 PP-24-06334 Mounting Flange X Style 1 9103 PP-24-09103EX Gasoline Flange Kit 70 PP-24-09468 Oil Seal Kit PP-24-06316 Plunger Oil Seal 3 71 PP-24-09465 Plunger Packing Kit PP-24-06290 Support Ring 3 PP-24-06315 V-Sleeve 3 72 PP-24-09466 Valve Assembly Kit PP-24-07374 Valve Spring 3 PP-24-06267 Guided P-Valve 3 PP-24-06295 Discharge Valve Cone 3 PP-24-07373 Discharge Valve Spring 3 73 PP-24-09534 Regulator Repair Kit PP-24-23507 O-Ring 1 PP-24-06710 Seat 1 PP-24-06386 6mm S.S. Ball 1 PP-24-06385 O-Ring 1 PP-24-06384 Plastic Poppet Valve 1 PP-24-06410 O-Ring 1 6
CYLINDER HEAD - GX200QAPW 1 12204-ZE1-306 GUIDE, IN. VALVE(O.S.) 1 2 12205-ZE1-315 GUIDE, EX. VALVE(O.S.) 1 3 12210-ZL0-415 HEAD COMP., CYLINDER 1 4 12216-ZE5-300 CLIP, VALVE GUIDE 1 5 12251-ZL0-003 GASKET, CYLINDER HEAD 1 6 12310-ZE1-020 COVER COMP., HEAD 1 7 12391-ZE1-000 PACKING, HEAD COVER 2 8 15721-ZH8-000 TUBE, BREATHER 1 10 90013-883-000 BOLT, FLANGE, 6X12(CT200) 4 11 90043-ZE1-020 BOLT, STUD, 6X112 2 12 90047-ZE1-000 BOLT, STUD, 8X32 2 13 94301-10160 DOWEL PIN, 10X16 2 14 95701-08060-00 BOLT, FLANGE, 8X60 4 15 98079-56876 PLUG, SPARK(BPR6ES)(NGK) 1 7
CYLINDER BARREL - GX200QAPW 1 12000-Z0V-406 BARREL ASSY., CYLINDER 1 2 15510-ZE1-033 SWITCH ASSY., OIL LEVEL 1 3 16506-ZL0-000 GOVERNOR ASSY. 1 4 16531-ZE1-000 SLIDER, GOVERNOR 1 5 16541-ZE1-000 SHAFT, GOVERNOR ARM 1 6 90131-ZE1-000 BOLT, DRAIN PLUG 2 7 90451-ZE1-000 WASHER, THRUST, 6MM 1 8 90601-ZE1-000 WASHER, DRAIN PLUG, 10.2MM 2 9 90602-ZE1-000 CLIP, GOVERNOR HOLDER 1 10 91001-ZF1-003 BEARING, RADIAL BALL(6205TMB) (NTN) 1 91001-ZF1-004 BEARING, RADIAL BALL(6205SH) (KOYO) 1 91001-Z4X-003 BEARING, RADIAL BALL, 6205 (NSK) 1 11 91201-Z0T-801 OIL SEAL, 25X41X6 1 12 91353-671-004 O-RING, 14MM(NOK) 1 13 94050-10000 NUT, FLANGE, 10MM 1 14 94101-06800 WASHER, PLAIN, 6MM 2 15 94251-08000 PIN, LOCK, 8MM 1 16 95701-06012-00 BOLT, FLANGE, 6X12 2 17 35480-Z0T-003 SWITCH ASSY., OIL LEVEL 1 8
CRANKCASE COVER - GX200QAPW 2 11300-ZE1-642 COVER ASSY., CRANKCASE 1 3 11381-ZL0-000 PACKING, CASE COVER 1 4 15600-Z0T-810 CAP ASSY., OIL FILLER 1 5 15600-Z0T-820 CAP ASSY., OIL FILLER 1 6 15625-Z0T-800 PACKING, OIL FILLER CAP 2 CRANKSHAFT - GX200QAPW 7 91201-Z0T-801 OIL SEAL, 25X41X6 1 8 94301-08140 DOWEL PIN, 8X14 2 9 95701-08032-00 BOLT, FLANGE, 8X32 6 10 96100-62050-00 BEARING, RADIAL BALL, 6205 1 2 13310-ZL0-602 CRANKSHAFT COMP. 1 9 90745-ZE1-600 KEY, 4.78X4.78X38 1 9
PISTON - GX200QAPW 1 13010-Z4K-004 RING SET, PISTON(STD.) (TEIKOKU) 1 13011-Z4K-004 RING SET, PISTON(0.25) (TEIKOKU) (1) 13012-Z4K-004 RING SET, PISTON(0.50) (TEIKOKU) (1) 13013-Z4K-004 RING SET, PISTON(0.075) (TEIKOKU) (1) 13010-Z4M-003 RING SET, PISTON(STD.) (RIKEN) 1 13011-Z4M-003 RING SET, PISTON(0.25) (RIKEN) (1) 13012-Z4M-003 RING SET, PISTON(0.50) (RIKEN) (1) 13013-Z4M-003 RING SET, PISTON(0.075) (RIKEN) (1) 2 13101-ZL0-020 PISTON(STD.) 1 13102-ZL0-020 PISTON(0.25) (1) 13103-ZL0-020 PISTON(0.50) (1) 13104-ZL0-020 PISTON(0.75) (1) 3 3111-ZE1-000 PIN, PISTON 1 4 13200-Z0T-800 ROD ASSY., CONNECTING 1 5 90001-ZE1-000 BOLT, CONNECTING ROD 2 6 90551-ZE1-000 CLIP, PISTON PIN, 18MM 2 CAMSHAFT - GX200QAPW 1 12209-ZH8-003 SEAL, VALVE STEM (T) 1 12209-Z4M-801 SEAL, VALVE STEM (T2) 1 2 14100-ZL0-000 CAMSHAFT ASSY. 1 3 14410-ZE1-010 ROD, PUSH 2 4 14431-ZE1-000 ARM, VALVE ROCKER 2 5 14451-ZE1-013 PIVOT, ROCKER ARM 2 6 14568-ZE1-000 SPRING, WEIGHT RETURN 1 7 14711-ZF1-000 VALVE, IN. 1 8 14721-ZF1-000 VALVE, EX. 1 9 14731-ZL0-000 LIFTER, VALVE 2 10 14751-ZF1-000 SPRING, VALVE 2 11 14771-ZE1-000 RETAINER, IN. VALVE SPRING 1 12 14773-ZE1-000 RETAINER, EX. VALVE SPRING 1 13 14781-ZE1-000 ROTATOR, VALVE 1 14 14791-ZE1-010 PLATE, PUSH ROD GUIDE 1 15 90012-ZE0-010 BOLT, PIVOT, 8MM 2 16 90206-ZE1-000 NUT, PIVOT ADJUSTING 2 10
RECOIL STARTER - GX200QAPW 1 28400-Z4M-003ZC STARTER ASSY., RECOIL (BLACK) 1 28400-Z4M-003ZA STARTER ASSY., RECOIL (RED) 1 2 28405-ZL0-000ZA SPACER, RECOIL STARTER (BLACK) 1 28405-ZL0-000ZC SPACER, RECOIL STARTER (RED) 1 3 28410-Z4M-003ZD CASE COMP., RECOIL STARTER (BLACK) 1 28410-Z4M-003ZB CASE COMP., RECOIL STARTER (RED) 1 4 28421-Z0T-003 REEL, RECOIL STARTER 1 5 28422-ZH8-801 RATCHET, STARTER 2 6 28431-ZH8-801 PLATE, FRICTION 1 7 28433-ZH8-801 GUIDE, RATCHET 1 8 28441-ZH8-801 SPRING, FRICTION 1 9 28442-ZH8-003 SPRING, RECOIL STARTER 1 10 28443-ZH8-801 SPRING, RETURN 2 11 28461-Z4M-003 KNOB, RECOIL STARTER 1 12 28462-ZH8-003 ROPE, RECOIL STARTER 1 13 28463-Z4M-003 KNOB, REINFORCEMENT 1 15 90003-ZH8-801 SCREW, SETTING 1 17 95701-06018-00 BOLT, FLANGE, 6X18 3 11
FAN COVER (1) - GX200QAPW 1 19610-ZL0-000ZJ COVER COMP., FAN (RED) 1 19610-ZL0-000ZD COVER COMP., FAN (BLACK) 1 3 19611-ZH8-810 PLATE COMP., SIDE(OIL ALERT) 1 5 19630-ZH8-000 SHROUD COMP. 1 6 34150-ZH7-013 ALERT UNIT, OIL 1 7 35120-Z0T-801 SWITCH ASSY., ENGINE STOP 1 FAN COVER (2) - GX200QAPW 8 35120-Z0T-851 SWITCH ASSY., ENGINE STOP 1 9 90013-883-000 BOLT, FLANGE, 6X12(CT200) 6 10 90022-888-010 BOLT, FLANGE, 6X20(CT200) 1 11 90601-ZH7-013 CLIP, HARNESS 1 12 95701-06008-00 BOLT, FLANGE, 6X8 1 2 19610-Z4M-000ZA COVER COMP., FAN (RED) 1 19610-Z4M-000ZB COVER COMP., FAN (BLACK) 1 4 19611-Z4M-810 PLATE COMP., SIDE(OIL ALERT) 1 9 19630-ZH8-000 SHROUD COMP. 1 11 34150-ZH7-013 ALERT UNIT, OIL 1 13 35120-Z0T-851 SWITCH ASSY., ENGINE STOP 1 15 90013-883-000 BOLT, FLANGE, 6X12(CT200) 6 16 90022-888-010 BOLT, FLANGE, 6X20(CT200) 1 17 90601-ZH7-013 CLIP, HARNESS 1 19 95701-06008-00 BOLT, FLANGE, 6X8 1 12
CARBURETOR - GX200QAPW 1 16010-ZE1-812 GASKET SET 1 2 16011-ZE0-005 VALVE SET, FLOAT 1 3 16013-Z0S-B01 FLOAT SET 1 4 16015-ZE0-831 CHAMBER SET, FLOAT 1 5 16016-ZE0-005 SCREW SET, PILOT 1 6 16016-ZH7-W01 SCREW SET, PILOT 1 7 16024-ZE1-811 SCREW SET, DRAIN 1 8 16028-ZE0-005 SCREW SET 1 9 16044-Z4M-911 CHOKE SET (T) 1 16044-Z4M-911 CHOKE SET (T2) 1 10 16100-Z0V-V71 CARBURETOR ASSY.(BE59J A) 1 11 16124-ZE0-005 SCREW, THROTTLE STOP 1 12 16166-ZL0-000 NOZZLE, MAIN 1 16166-Z4V-921 NOZZLE, MAIN 1 13 16173-001-004 PACKING, FUEL STRAINER CUP 1 14 16211-ZL0-000 INSULATOR, CARBURETOR 1 15 16212-ZH8-800 PACKING, INSULATOR 1 16 16220-ZE1-020 SPACER COMP., CARBURETOR 1 17 16221-ZH8-801 PACKING, CARBURETOR 1 18 16610-ZE1-000 LEVER COMP., CHOKE(STD.) 1 19 16953-ZE1-812 LEVER, COCK 1 20 16954-ZE1-812 PLATE, LEVER SETTING 1 21 16956-ZE1-811 SPRING, COCK LEVER 1 22 16957-ZE1-812 PACKING, FUEL COCK 1 23 16967-ZE0-811 CUP, FUEL STRAINER 1 24 93500-03006-1H SCREW, PAN, 3X6 2 25 94305-20122 PIN, SPRING, 2X12 1 26 99101-ZH8-0700 JET, MAIN, #70 1 99101-ZH8-0720 JET, MAIN, #72 1 99101-ZH8-0750 JET, MAIN, #75 1 99101-ZH8-0680 JET, MAIN, #68 1 27 99204-ZA0-0450 JET SET, PILOT, #45 1 99204-ZE2-0400 JET SET, PILOT, #40 1 35 16211-Z4V-000 INSULATOR, CARBURETOR 1 13
AIR CLEANER(DUAL) - GX200QAPW 1 16271-ZE1-000 PACKING, ELBOW 1 2 17210-ZE1-822 ELEMENT, AIR CLEANER(DUAL) 1 3 17218-ZE1-821 FILTER, OUTER 1 4 17230-ZE1-820 COVER, AIR CLEANER(DUAL) 1 5 17232-891-000 GROMMET, AIR CLEANER 1 6 17235-Z4M-830 NOSE, SILENCER 1 7 17238-ZE7-010 COLLAR, AIR CLEANER 2 8 17239-ZE1-000 COLLAR B, AIR CLEANER 1 9 17410-ZE1-020 ELBOW COMP., AIR CLEANER 1 10 90325-044-000 NUT, TOOL BOX SETTING 2 11 94050-06000 NUT, FLANGE, 6MM 2 12 95701-06020-00 BOLT, FLANGE, 6X20 1 13 17231-Z4M-000 COVER, AIR CLEANER 1 14 90300-Z1V-000 NUT, AIR CLEANER 1 14
MUFFLER - GX200QAPW 1 18310-ZL0-000 MUFFLER COMP. 1 2 18315-ZE1-000 STAY, MUFFLER 1 3 18320-ZF1-H51 PROTECTOR, MUFFLER(SILENT) (T) 1 18320-Z4V-000 PROTECTOR COMP., MUFFLER (T2) 1 5 18355-ZL0-000 ARRESTER, SPARK 1 6 18361-ZL0-000 NETTING, WIRE FLANGE 1 7 18381-Z0T-801 GASKET, MUFFLER 2 8 90016-ZE1-000 BOLT, FLANGE, 6X13(CT200) 1 9 90050-ZE1-000 SCREW, TAPPING, 5X8 4 10 90055-ZE1-000 SCREW, TAPPING, 4X6 1 12 90056-ZL0-000 SCREW, TAPPING, 4X6 1 13 94001-08000-0S NUT, HEX., 8MM 2 14 95701-06012-00 BOLT, FLANGE, 6X12 1 15 18310-Z4V-000 MUFFLER COMP. 15
FUEL TANK (1) - GX200QAPW 1 16854-ZH8-000 RUBBER, SUPPORTER(107MM) 1 2 16955-ZE1-000 JOINT, FUEL TANK 1 3 17510-Z0T-010ZC TANK COMP., FUEL (MCKINLEY WHITE) 1 17510-Z0T-010ZA TANK COMP., FUEL (BLACK) 1 5 17631-Z0T-801 PACKING, FUEL FILLER CAP 1 7 90004-ZL0-003 BOLT, FLANGE, 6X34 1 FUEL TANK (2) - GX200QAPW 8 91353-671-004 O-RING, 14MM(NOK) 1 9 94050-06000 NUT, FLANGE, 6MM 2 10 91424-Z4F-802 TUBE, FUEL, 4.5X140(FKM) 1 21 95002-40800-0 CLAMP, TUBE(D8) 2 22 7620-Z4H-020 CAP COMP., FUEL FILLER 1 1 16854-ZH8-000 RUBBER, SUPPORTER(107MM) 1 2 16955-ZE1-000 JOINT, FUEL TANK 1 3 17510-Z4M-000ZA TANK COMP., FUEL (MCKINLEY WHITE) 1 17510-Z4M-000ZB TANK COMP., FUEL (BLACK) 1 5 17620-Z4H-020 CAP COMP., FUEL FILLER 1 7 17631-Z0T-801 PACKING, FUEL FILLER CAP 1 9 90004-ZL0-003 BOLT, FLANGE, 6X34 1 11 91353-671-004 O-RING, 14MM(NOK) 2 12 91424-Z4M-003 TUBE, FUEL, 4.5X145(FKM) 1 13 94050-06000 NUT, FLANGE, 6MM 2 15 95002-40800-08 CLAMP, TUBE(D8) 1 16
FLYWHEEL - GX200QAPW 1 13331-357-000 KEY, SPECIAL WOODRUFF, 25X18 1 2 19511-ZE1-000 FAN, COOLING 1 7 31100-ZE7-010 FLYWHEEL COMP.(STD.) 1 9 90201-Z0T-800 NUT, SPECIAL, 14MM 1 11 28451-ZL0-801 PULLEY, STARTER 1 IGNITION COIL - GX200QAPW 1 30500-Z0T-802 COIL ASSY., IGNITION 1 2 30700-Z0T-811 CAP ASSY., NOISE SUPPRESSOR 1 9 36101-ZE1-010 CORD, STOP SWITCH(370MM) 1 12 90121-952-000 BOLT, FLANGE, 6X25(CT200) 2 17
CONTROL - GX200QAPW 2 16500-ZH8-823 CONTROL ASSY.(REMOTE) (T) 1 16500-Z4M-820 CONTROL ASSY.(REMOTE) (T2) 1 3 16551-ZL0-000 ARM, GOVERNOR 1 4 16555-ZE1-000 ROD, GOVERNOR (T) 1 16555-Z4M-000 ROD, GOVERNOR (T2) 1 5 16561-ZL0-000 SPRING, GOVERNOR 1 6 16562-ZE1-020 SPRING, THROTTLE RETURN 1 8 16571-ZH8-020 LEVER, CONTROL (T) 1 16571-Z4M-000 LEVER, CONTROL (T2) 1 9 16574-ZE1-000 SPRING, LEVER 1 10 16575-ZH8-000 WASHER, CONTROL LEVER 1 11 16576-891-000 HOLDER, CABLE 1 12 16578-ZE1-000 SPACER, CONTROL LEVER 1 13 16580-ZH8-813 BASE COMP., CONTROL(REMOTE) (T) 1 16580-Z4M-810 BASE COMP., CONTROL(REMOTE) (T2) 1 14 16584-883-300 SPRING, CONTROL ADJUSTING 1 15 16592-ZE1-810 SPRING, CABLE RETURN 1 17 90013-883-000 BOLT, FLANGE, 6X12(CT200) 2 18 90015-ZE5-010 BOLT, GOVERNOR ARM 1 20 90114-SA0-000 NUT, SELF-LOCK, 6MM 1 21 93500-05016-0A SCREW, PAN, 5X16 1 22 93500-05025-0H SCREW, PAN, 5X25 1 24 94050-06000 NUT, FLANGE, 6MM 1 GASKET SET - GX200QAPW 1 06111-ZL0-000 GASKET KIT 1 18
Warranty Celtic Distributors Ltd. will repair or replace, free of charge, any part or parts that are defective in material or workmanship or both. Transportation on parts or equipment submitted for repair or replacement under this warranty remains the responsibility of the purchaser. This warranty is effective for the time periods and subject to the conditions provided for in this policy. Warranty work must be performed by an authorized Warranty Depot. For details on warranty locations, contact Celtic Distibutors Ltd. toll free at 1-800-663-4742. Storm Jet reserves the right to refuse any claim do to negligence or abuse. Warranty Period Warranty coverage commences on the date of purchase by the end user or on the date the product has been first used for demonstration purposes. Storm Jet Engines Storm Jet Pumps Storm Jet Frames Storm Jet All Other Accessories & Fittings HONDA,GC SERIES ENGINES - (Model: HG272E) - 2 year residential / 3 month commercial HONDA, GX SERIES ENGINES - (Model: HG253E / HG292E) - 3 year commercial Giant Axial - (Model: HG272E) - 2 year Giant Triplex - (Model: HG253E, HG292E, HG354C) - 5 year General Pump Triplex - (Model: HGP403C, ihgp404c) - 5 year 5 years 90 Days Customer Responsibility 1. Customer must complete and submit warranty registration form provided with each new machine within 90 days of purchase date. 2. Proper service must be performed as detailed in the owner s manual. NOTE: Use only synthetic 15W50 pump oil, as indicated in the owner s manual. 3. Modifications and after market parts or accessories may void overall warranty coverage. 4. Repairs required as a result of collision, accident, negligence, misuse and lack of maintenance are not covered under warranty. 5. Repair work, including disassembly inspections, must be performed by an authorized Warranty Depot. 6. Customer must provide the means of delivering the product to and from the Warranty Depot. (Freight is not a warrantable expense). For the nearest Warranty Depot, please call Celtic Distibutors Ltd. toll free at 1 (800) 663-4742. Disclaimer 1. Items not covered under warranty include normal wear & tear items such as O-rings, V-sleeves and packings, hose outer protective jacket and spray nozzles. 2. Storm Jet disclaims any responsibility for loss of time or use of the product, or any other indirect, incidental or consequential damage, inconvenience or commercial loss. 19
May 9, 2016