Section F Air Atomizing Spray Nozzles

Section F tomizing Overview If your application requires air atomizing nozzles, you ll find information on the largest selection in the industry available in this section. hoose from dozens of nozzle bodies, assemblies and spray set-ups to get the precise performance you require. atomizing nozzles require a single air source for the atomizing air. Some versions, equipped with a cylinder for automatic operation or clean-out and shut-off needles, may require an additional air line. Fluid lines are required for all models. The fluid line can be pressurized or supplied using a siphon- or gravityfed configuration. It is recommended that air and fluid lines are equipped with the proper filters, regulators and valves. atomizing nozzles require spray set-ups. Each set-up consists of an air cap and fluid cap and some may also include O-rings and retainer caps. You can select from a wide assortment of capacities, spray patterns and pressure- or siphon-fed set-ups. Product Range: 1/J and 1/J Series nozzles are available in many configurations and operate at standard flow rates. Ranges from: 0. to.1 at psi (2.0 to 2 l/h at 2. bar). Variable spray nozzles provide independent control of liquid, atomizing air and fan air pressure for fine tuning of flow rate, drop size, spray distribution and coverage. 1/2J Series nozzles offer the same features and benefits as 1/J and 1/J Series but operate at higher capacities. Ranges from:.2 to 2 at psi ( to l/h at 2. bar). 1J Series nozzles offer the highest flow rates available. Ranges from: 1 to 0 at psi ( to l/h at 2. bar). dditional information can be found in Section G, utomatic and in Section K, Special Purpose. tomizing Table of ontents asic Information s................................................... F Features... F 1/J and 1/J Series Overview/Nozzle odies/nozzle ssemblies.................. F Pressure s, Internal Mix........................ F Pressure s, External Mix... F1 Pressure s, Internal Mix, High Transfer Efficiency (HTE)... F1 Siphon/Gravity-Fed s, External Mix... F2 1/JJ ompact Series Overview................................................ F2 Nozzle odies/nozzle ssemblies.......................... F2 Pressure s, Internal Mix....................... F2 Pressure s, External Mix, High apacity......... F1 Pressure s, Internal Mix, Efficient........... F Siphon/Gravity-Fed s, External Mix... F Variable Series Variable... F Pressure s, External Mix... F 1/2J Series Nozzle odies/nozzle ssemblies.......................... F Pressure s, Internal Mix....................... F Pressure s, External Mix... F Siphon/Gravity-Fed s, External Mix... F tomizing atomizing caps 1J Series Nozzle odies/nozzle ssemblies.......................... F0 Pressure s, Internal Mix....................... F1 Pressure s, External Mix... F Siphon/Gravity-Fed s, External Mix... F Special Purpose Jet Fogger... F ripsafe Jet Fogger... F Humidification and Units..................... F Humidification System omponents......................... F tomizing ccessories... F1 Phone 1-00--spray, FX 1---spray F1

tomizing tomizing Optimization Tips Reduce installation time by using split-eyelet connectors on both the air and fluid lines. Split-eyelet connectors only require a hole drilled into the pipe, eliminating the need for cutting, threading and brazing operations. To eliminate the unintentional release of non-atomized liquid, use a check valve to shut down liquid flow if no air pressure is detected. Use air atomizing nozzles with clean-out needles to eliminate clogging and ensure optimum performance. Use strainers and air filters to ensure optimum performance. If positive shut-off is required, use rip Free set-ups with JU nozzles. Use a heat jacket with VU/VMU variable spray nozzles to keep viscous liquids warm and transferable. When adjusting air pressure with internal mix nozzles, do not exceed recommended values as it may result in choking liquid flow. Increasing liquid flow can also choke air flow. For optimal control of your air atomizing spray system, the use of an utojet System helps conserve liquid usage and reduces scrap by monitoring and automatically adjusting spray pattern, flow rate, drop size, liquid pressure and atomizing air pressure. utojet ontrollers and Systems atomizing nozzles with clean-out needles Heat jackets nozzles Hot fluid flow channel ut out view of heat jacket showing unique flow channel Phone 1-00--spray, FX 1---spray F2

s, asic Information Liquid can be supplied to the nozzle under pressure or it can be supplied through a liquid siphon or gravity-feed. Pressure s Siphon/Gravity-Fed s Liquid is supplied to the nozzle under pressure. and liquid can be externally or internally mixed to produce a completely atomized spray. 1/J and 1/J Series Pages F F1 1/2J Series Pages F F 1J Series Pages F0 F2 ompact 1/JJ Series Pages F2 F Variable 1/V Series Pages F F2 New High Transfer Efficiency (HTE) external mix air atomizing set-ups recently introduced for 1/J Series. Pages F1 F Liquid is supplied via liquid siphon or is gravity-fed. esigned to draw liquid through the feed line into the air flow where it is atomized. 1/J and 1/J Series Pages F2 F ompact 1/JJ Series Pages F F 1/2J Series Page 1J Series Page tomizing 1/JN air atomizing nozzle pressure regulator with gauge shut-off valve filter inlet Liquid inlet Liquid shut-off valve pressure regulator with gauge 1/JN air atomizing nozzle Siphon tube Siphon height shut-off valve filter inlet Liquid pressure regulator with gauge TW liquid strainer Liquid container Phone 1-00--spray, FX 1---spray F

Features, asic Information tomizing Features Each series is available with a pressure spray set-up or siphon spray set-up. Each set-up provides a specific spray pattern with a specific capacity and spray coverage range performance. set-ups are interchangeable for each nozzle series. Round spray: Extended full cone round spray pattern. Wide angle round spray: Hollow cone-type, wide angle round spray pattern. circular spray: Hollow cone-type circular spray pattern. Flat spray: Extended flat or sheet-type spray pattern. eflected flat spray: Extended flat or sheet-type spray diverted away from the axis of the inlet connection. Each spray set-up consists of an air cap and fluid cap. For more information request ata Sheets 1 and 1-1. tomization ontrol Features chieved by adjusting the air and liquid pressure in the spray set-up. Obtaining finer atomization is accomplished by increasing the air pressure and/or lowering the liquid pressure, resulting in a high ratio of air flow rate to liquid flow rate. External mix with pressure set-ups: Flat and round spray patterns. cap Fluid cap Internal Mix Features Liquid and air are mixed internally to produce a completely atomized spray. Liquid and gas streams are not independent and a change in air flow will affect the liquid flow. Internal mix uses pressure set-ups and is available with the following spray patterns: circular spray. eflected flat spray. Elliptical spray. Flat spray. Round spray. Wide angle round spray. External Mix Features Liquid and air streams are mixed outside of the nozzle. and liquid flow can be controlled independently. Effective for higher viscosity liquids and abrasive suspensions. External mix can use siphon set-ups or pressure set-ups. When a siphon set-up is used, a round spray pattern is produced. When a pressure set-up is used, a flat spray pattern is produced. Internal mix with pressure set-ups: Round spray patterns Internal mix with pressure set-ups: Flat spray patterns External mix with siphon set-ups: Round spray patterns External mix with pressure set-ups: Flat spray patterns Phone 1-00--spray, FX 1---spray F

Overview/Nozzle odies/nozzle ssemblies, 1/J and 1/J Series 1/J and 1/J Series air atomizing 1/J, 1/J set-up for HTE Plug P 1/JN, 1/JN 1 2 set-up Shut-off needle assembly 1/JO, 1/JO 10 1/J, 10 1/J 1 2 1. Retainer ring P 2. cap. Fluid cap. Fluid cap gasket P. Nozzle body P1. ack seal gasket P set-up for rip Free lean-out needle assembly 2 Shut-off/clean-out needle assembly 1 tomizing 1/JU rip Free 1 2 Shut-off/clean-out needle assembly Features and enefits The basic J Series nozzle assembly consists of a body and a spray set-up. Various assemblies can be added to provide shut-off and clean-out functions. 1/J and 1/J bodies have liquid and air feeds at opposite ends of the body. odies are provided with a removable plug so other needle assemblies may be added in the future. JN features a manual shut-off needle that enables the flow of liquid to the nozzle to be stopped. JO features a clean-out needle that is activated manually. The needle slides through the liquid orifice to clear obstructions. Ideal for intermittent spraying applications when liquid can dry in the orifice between uses. 10 combines the features of JN and JO offering a combination shut-off/clean-out needle. Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, 1/J and 1/J Series tomizing 1/J, 1/J 1/" and 1/" NPT or SPT Optimization Tips See page F2 for optimization tips. 1/JN, 1/JN 1/" and 1/" NPT or SPT with shut-off needle 1/JO, 1/JO 1/" or 1/" NPT or SPT with clean-out needle See lso ccessories line filters pressure regulators Liquid pressure regulators 10-1/J, 1/J 1/" or 1/" NPT or SPT with shut-off/clean-out needle Pressure gauges Solenoid valves Strainers http:// s Ordering Info Nozzle odies Electroless Nickelplated rass ode Nozzle Type J JN JO 10 (none) l l l l Stainless Steel SS l l l l Lucite * LU l s Lucite* LU l Electroless Nickelplated rass ap and Stainless Steel SSR l l l l Stainless Steel SS l l l l *May not be available for all spray set-ups listed. Other materials available upon request. omplete Nozzle ssembly Nozzle ody* *Includes retainer and gasket. 1/ JN SS SUF SS l l l l l Inlet onn. Nozzle ody ssembly Type ode ode SPT connections require the addition of a prior to the nozzle body inlet connection. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: 0-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: -SS. To order spray nozzle without set-up, use inlet connection, nozzle body and material code: 1/JN-SS. Only SUF l To order spray set-up only, use spray set-up number and material code: SUF-SS. SS l ode Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, 1/J and 1/J Series Features and enefits 1/JF features a built-in liquid strainer. 1/JFN features built-in liquid strainer and liquid shut-off needle. J features the center lines of the air and liquid inlet entering in the back of the nozzle and parallel to the spray projection axis. J features air and liquid inlet connections entering the nozzle at 0 to spray projection axis. JN features air and liquid inlet connections entering the nozzle at 0 to spray projection axis and a shut-off needle. 1/-2J dual spray assembly features two opposing spray set-ups with the air and liquid inlet connections perpendicular to the spray axis. The multiple swivel spray assembly features each spray set-up mounted on its own swivel body. One or two bodies may be used and each can be rotated to the desired position. Swivel bodies are locked in place by a stainless steel lock screw that runs vertical through the assembly. 2-1/J miniature assembly body is only 1/2" ( mm) thick with a 1-/2" (2 mm) by 1-1/" (2 mm) rectangular face. The tip of the nozzle projects from the face a maximum of 1-/1" ( mm) depending upon the spray set-up used. 1/JJ features a steam jacket around the nozzle body for spraying liquids that are too viscous to spray at room temperature. With Strainer ack onnect Top Inlet Top Inlet 1/JF and 1/JFN 1/" NPT or SPT (F) air inlet connection 1/" NPT or SPT (F) liquid inlet connection 1/J and 1/J 1/" or 1/" NPT or SPT (F) inlet connection 1/J, 1/JN 1/J, 1/JN 1/" or 1/" NPT or SPT (F) inlet connection 1/-2J 1/" NPT or SPT (F) inlet connection tomizing Swivel Miniature Optimization Tips See page F2 for optimization tips. See lso http:// 1/" NPT or SPT (F) air and liquid inlet connection Steam Jacket 1/JJ 1/" NPT or SPT (F) inlet/outlet connection 2-1/J 1/" NPT or SPT (F) air and liquid inlet connection ccessories line filters pressure regulators Liquid pressure regulators Strainers For J, request ata Sheets, and 1 For J and JN, request ata Sheets and -1 For 1/-2J dual spray assembly, request ata Sheet For multiple swivel spray assembly, request ata Sheet For 2-1/J, request ata Sheet 2 Pressure gauges Solenoid valves For 1/JJ, request ata Sheets and 1 Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, 1/J and 1/J Series tomizing Features and enefits multiple spray assembly (cluster type) features five spray set-ups located on the faces of the assembly or four set-ups located on the side faces. 2J is a dual spray assembly with opposing spray set-ups perpendicular to opposing air and liquid inlets. Thin wall adapters add an adapter locknut and gasket to P thick wall adapters to provide secure mounting in thin walls and include P locknut and P20- gasket. Thick wall adapters replace retainer rings on nozzle assemblies and fit into threaded wall openings, holding the nozzle securely in place. 1/JLN and 1/JLO feature a screw mount with /2" ( mm) diameter mounting holes. Standard 1/" ( mm) screws hold the body to the wall with a gasket providing the seal. The 1/JLN features a shut-off needle and the 1/JLO features a clean-out needle. 0 Series hand-held air atomizing spray guns feature lightweight aluminum construction and a comfortable, easy-to-operate design. Extensions are available in up to " (1 cm) lengths. luster Type Twin Thin Walls Thick Walls 1/" NPT or SPT (F) air and liquid inlet connection 2J 1/" NPT or SPT (F) inlet connection vailable for 1/J and 1/J assemblies 1/J and 1/J with /" NPT or SPT (M) adapter connection Screw Mount Optimization Tips See page F2 for optimization tips. 1/" NPT or SPT (F) air and liquid inlet connection 0 Hand-held spray gun 1/" NPT or SPT (F) inlet connection See lso ccessories line filters pressure regulators Pressure gauges Solenoid valves Liquid pressure regulators Strainers For multiple spray assembly, request ata Sheet For 2J, request ata Sheets and For thin wall adapters, request ata Sheet For thick wall adapters, request ata Sheets, 00 and 2 For 1/JLN and 1/JLO, request ata Sheet 0 For 0 Series hand-held air atomizing spray guns, request ata Sheets 0J, 0JN, 0JMO, 0JN-1, 0JJ, 0JJN and 0JJNTK http:// Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series s Round spray air caps produce a narrow, full cone round spray pattern Features and enefits For round spray pattern, angle is maintained throughout distance. eyond, the spray becomes turbulent and will project out to distance. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. cap Fluid cap Round spray pattern Performance ata retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. retainer ring gasket tomizing Round SU 0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0...0 1.0. 1.. 2 1.. 0 2.2..0.. 1.0 1.2.0 2 1.. 1.2.0 2.0 1.0.0.... 2 1.0.2 1.2. 1.0 1.1..0.. 1.0 1.0 2 1. 1. 2.2..2 1.0. 1.2 1.2 1.2 2..2. 1. 0.2 1. 1.2 1... 2. 1.1 2. 1. 0 1. 1. dd F to part number for rip Free set-ups. Example: SUF. * 2 Liquid* imensions ngle ( ) 1 1-1/2 1-1/2 (ft.) -1/2-1/2 Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series tomizing Performance ata Round SU 0 1 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0.. 1.0 1.. 1. 1.00 2. 1.. 1..0.. 1.2. 2 1. 1.1 2.1 1.2 2. 1..0.2.0 1. 1.0 2 1. 1. 1.2 1. 2 2. 1. 1.0 1.1 1.2 1. 2 1.2 1. 2.2 2.0 2.0 1.2 1. 1. 1.0 1. 2 2. 2.2 1. 1. 1. 1. 1. 2. 1.02 1. 1.2 1. 0 1. 2. * 2 Liquid* imensions ngle ( ) 1 1 1 1 (ft.) 1 1 SU 20 1.0 1.2. 2.1 1.0 2.0 1..2 1.2.2 1.0 1.0 1.0. 2 1. 1.2 2. 1.2. 1. 2.2 1..0 1.1 1. 1. 2. 1.. 1..2 1..1 1.2 1.2 1. 2 1. 1. 2.0 1.. 1.. 1. 1.0 1. 1.0 2.0 2 2. 2.01.0 2.0 2. 1. 1.02 1. 0 1. 2.2 2.1 2..2 2.2 2. 1. 2. 2.0 2 1. 2. 1. 2. 0. 2. 2 1 1 2-1/2 1 1 1-1/2 SU 0 1 1.0. 2. 2.0.1..2.... 2.. 2.0.1.0.1..0.. 1.0. 2......2 0..2 1..0 1.. 2..0 1..0..0 2 1.2. 1.. 1.. 0 1.. 0.. 2...0. 1.0. 1.00.0..0.2. 0.. 0.. 0.2. 0.2. 1 2 2 1 2 SU 0 1.0.1 2.00. 2. 1..2 1.. 2...0. 2.2.0 2..1. 2 1.... 1.0. 2..2.1..2..1 1.. 1.0..00 2....1 0.. 0 1.2. 2.2. 2..0 2...2.0..0.... 0.0. 2....0...0.0 2 0 0 1 1 2 1 1 1 2 2 SU2 010.0..0 2..0 2.. 2..1 2 0..1 1.0.. 2.0. 2.. 2.2..0. 1.0. 2 2...1.0 0.0. 2.... 2.0..2. 2......0..1 1........0 0 1.. 0.0. 1 1 2 2 2 2 dd F to part number for rip Free set-ups. Example: SUF. Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series s Features and enefits Wide angle round spray and circular spray air caps produce hollow cone, wide angle round spray and circular spray patterns. Performance ata Wide ngle Round SU1 SU2 SU2 0 ---0 0 1---0 0 1---0 For wide angle round spray, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. Wide angle round spray pattern retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. " (1 cm) " (2 cm) 1" ( cm) cap Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1.1..0 2..2 2.. 2.. 2..1.0 1.. 1.0 1.0.0 2 2.02. 2.2.1 2.2..0..0 1.0 1.. 1.1. 1.0. 2. 1..0.. 1.. 1.1 1.00 2 1.0 1.1 1.2 1. 1.1.1.1 1.0 1. 1.2 1.0 1..1.0. 1.1.0 1. 0 1.0 1.0.0 1. 1.. 2.. 2.. 2....0. 2. 2. 2. 2.2 2. 2.0.2.. 2 1..0..1.0.2..0 2.0.0.0.0..2 1.. 2.2.2...0. 0 1.. 0.0.00 2.. 1...0. 1..0 1..2 2.0. 2. 1.2 2..0. 1.. 2.00 2. 2. 2. 2.2...0 2.0 2.00.1 2.. 2.0....0 2. 2.0...1.2..2.... 0.. 2.. 0..1.0.1 2 2.2.1 0 2..1 dd F to part number for rip Free set-ups. Example: SUF. retainer ring * 2 Fluid cap Liquid* gasket imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 (ft.) -1/2-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1-1/2 1-1/2-1/2 tomizing Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series tomizing Performance ata Wide ngle Round SU2 0 1--2-0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0..0..1 1.. 1..0 0........ 0..2 1..1 2.0...1.. 0.. 0 1.. 2.2. 2....0..0 1......1 0.1. 0.2. 0 1.1. 2..0 0....2...0.2 2.. 0.. 0.. * Liquid* 2 2 0 imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 (ft.) 1 2 SU 0 1--- 1.0. 1. 2. 1. 2.2 2... 0..0 1.0 2.1 1. 2. 2.2.0 2....0. 2.0 1. 2. 2....1.0 0..2 1.2 1.0 1. 2. 0.0.2 0 2.1... 1. 2.0 2 1..00 2.. 1.2.2 0.00.0 2 1.0 2. 1.. 1.. 0 1.2. 2.2 2. 1.0.2 1.0. 1.0. 0 0 0-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 1 SU 010 1--2-0.... 1.. 1.. 2.2. 2.2. 2.. 2.... 0.. 2.0..2..2. 0.0.. 1..0..0.1.... 0 1. 1. 2 2.0.2.0. 2.. 0.. 0.0....0 1. 2 2.. 0 2.. 0 2. 1. 2 0-1/2-1/2-1/2-1/2 1 1-1/2 1 1-1/2 2 1 2 2 dd F to part number for rip Free set-ups. Example: SUF. ircular SU 10 1--2-1H Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 2...0 0.1..0... 2. 2... 2.2... 0.0.0 2.0 2. 2 2.... 0.1...1 2 1.. 1...2.1 0.1. 0. 1. 2 1.1.2 1.. 0 1.. 0 1. 1. dd F to part number for rip Free set-ups. Example: SUF. circular spray pattern Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series s Flat spray and deflected flat spray air caps produce flat or deflected flat spray patterns. Features and enefits For flat spray pattern, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. cap Fluid cap Performance ata Flat SU SU SUN 0 2 20 2 20 Flat spray pattern " (1 cm) " (2 cm) 1" ( cm) retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1.. 1.0 2.1 1. 2 2. 1. 2. 1..1 2..0 1.2. 1.2 1.1 2 2.1 1. 2 2. 2.01 2. 2..0 1.0 1.0 2 1.0 1.0 1. 1.2 2. 2.1 2.2.2 1.0. 1. 1. 1. 1. 2.00 0 1. 2. 1.. 1.0. 1.2. 1. 1. 2.1 1.2 2.1 0 1... 1.. 2.0 1.0 2...02 1..0. 1.. 2.1. 2. 0..2 0..2.0 2.1.0... 1.2. 1.. 2..0 1.0.2 2.1 1..1 1. 2. 1. 0. 2.2 1.0 1.. 2 2.0 1. 2. 1.. 1.. 2. 1.0 1.0 1.0 1. 1. 2 2.2 1. 0.0 2.0 0.0.. 1.2 2 1. 1. 1.2 2.0 1. 2. 2.. 1.1 1. 1. 2.1 1.2 2. 0 1... 1. 0 1.2 2.2 0..0 1...0 2...2 1.. 1.. 1..0 2. 1.0 2.1 1.0 2 2. 1. 2. 1.. 1.. 2. 1.0 1. 1. 2.1 1.2 2 2. 2.0. 2. 0..00 1. 1.2 1. 1. 1. 2. 2. 2...2.1 1. 1.2 2.1 0 1. 2. 1. 2. 0.0. 2. 1. 2.2 2...1 0 1.1. 0 2.. 2. 1.. 2. 0....2 0 2.0. dd F to part number for rip Free set-ups. Example: SUF. retainer ring * 1 0 1 2 0 0 Liquid* imensions 1 1-1/2 1 2 2 gasket 1 2 1 2 1 2 2 2 (ft.) -1/2-1/2-1/2-1/2 1 tomizing Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/J and 1/J Series tomizing Performance ata Flat SU SUN2 SU2 SU2 SU 20 0 0 2 0 2 010 11 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0 1.0 1.0 1. 1. 2 2.0 1. 2.1 2.1. 2..0 1.1 1. 1.1 1.0 1. 1. 2. 0 2. 2.0.2 1.2.0 1.0 1. 1. 1.1 2.2 2.1.. 1.. 1. 1. 2.0 0. 2. 0 1.. 2. 1.. 1. 0 1. 2. 2.2 1. 2. 1..0 2.. 2.0.0..0. 1.. 1..1 2.2 1. 2. 1.0 2.. 2.0 1.. 1.. 2. 1. 2. 1.0 2.0 1.1 2. 1.. 2.2. 2.... 1.2. 1.2.2 2. 2.. 0.. 2 2. 2.0 2.1 2... 0.. 1. 2.2 2..2 2.. 0 1...0 2.1 0 1.1.2 1.1.0.0. 1.0 2. 1.2 2. 2....0..0.0 1.0 2.2 2.. 2... 0.. 0.. 1.2 2. 2..0 2.. 2.0.1.0. 1.2 2.0 2...2...2 0..00 1.00 2.0 2.2.....0...2...0 0.2..0.0 1.1. 1.. 2.. 2. 1...0. 1. 2. 2.02. 2. 0.... 1.0.2 1..0 2. 2. 2...1 0.. 1.0. 1. 2.1 2.....0.. 2. 1.. 2..0.2..0 0.. 2.0 2.. 2. 0..1.....0.1 2..0 0..00 0...0..1 2.... 2 2..1..0 1.0.0. 2.0.1 1..2 2.1. 1.0.2....0 1.... 1.. 0.. 2.. 0.1.1 1.0.1 2.0. 0.... dd F to part number for rip Free set-ups. Example: SUF. * 0 1 2 0 2 2 1 2 2 0 Liquid* imensions 2 2 2 2 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 2 (ft.) -1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 eflected Flat SU2E 0 11- Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 2. 1..0. 2... 2.....0 2. 1. 1.0. 2... 2.....0 2.0 2. 1.0.1.1 2.0......0 1. 2. 2.... 2..2 2.2. 2.. 2..2 2.. 0 2.. dd F to part number for rip Free set-ups. Example: SUF. eflected flat spray pattern Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, 1/J and 1/J Series s External mix air caps produce a flat spray pattern. Features and enefits tomization can be controlled by varying the air pressure without changing liquid flow rates with external mix set-ups. For flat spray, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed externally to produce a completely atomized spray. cap Fluid cap Performance ata Flat spray pattern " (1 cm) " (2 cm) 1" ( cm) retainer ring gasket retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. tomizing Flat (External Mix) Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure * Liquid* imensions (ft.) SUE1 1 -.0.0..0 1.0..0 1. 1.1 2.0 1. 2. 2..0.0..0 1.0 1.1 1.0 1. 1. 2 2.0 1. 0 2..0.0.0 1.1 1.0 1.0 1. 1. 1. 2.0 2.1 2.. 1.0.0 1. 1.0 1. 2 1. 1. 2.0 2. 0 2..2.0 1. 2 1.0 1. 1. 2.1 0 2.0.0 2.. 2.0 1. 1.0 2.1 1. 2. 2.0. 0 2...0 2.1 1.0 2. 0 1..0 0 2.0. 0 2.. 1 2 0-1/2-1/2-1/2-1/2-1/2-1/2 dd F to part number for rip Free set-ups. Example: SUF. Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, 1/J and 1/J Series tomizing Performance ata Flat (External Mix) SUE1 1 - Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0.0..0 1.0..0 1...0 2.0 1.0.0 2. 1.2.0.0..0 1.0..0 1. 1.0.0 2.0 1.2 1.0 2. 1..0.0..0 1.0 1.0.0 1. 1.2 1.0 2.0 1. 2 2. 2.2.0.0 1.0.0 1.0 1.2.0 1. 1. 2.0 1. 2. 2..0 1.2..0 1. 1.1 1.0 2.2 1. 2.1 1.. 2. * 1 1 Liquid* imensions 1-1/2 1 1 1 1 1-1/2 (ft.) -1/2-1/2.0 1.2 1.1 1.0 1. 1. 2.2 1..1 2.1 0..0-1/2-1/2-1/2 SUE1 0-1.0 1.2 1. 1. 1. 2 2.2 1..1 2... 1.2 1. 2 1. 1. 2.2 2.1 0.1.0 0..2 2 1.2 1. 1. 2.1 2.2 2..1... 2 2-1/2-1/2-1/2 1.2 2.1 1. 2. 0 2.2.0 0.1.2 0.. 0-1/2 SUE1 0-1.2 2. 0 1..0 2.2. 0.1....0 1.2..0 1...0 2.2 1.0.0.1 1.2 1.0. 1..0 1.2 1.0.0 1. 1.2.0 2.2 1.2.1 1.. 1..0 1.2 1.2 1.0 1. 1. 2.2 1..1 2.. 2. 1.0 1.2 1. 1. 1. 2.2 2..1 2.. 2..0 2. 1.1 1.0.0 1..2 1..0 2. 0..0 1 2 2 1 1 1-1/2 1 1 1 1 1 1-1/2 1 1 2 2 2-1/2 1.0 2. 1..0 1. 2.2 1..0 2... 2-1/2 SUE1 20-2. 1. 2.0 1..2 2.1 0.0.0 0..2 2 2. 1..0 2.1.2 2..0... 2. 2.1.0 2. 0.2.0 0.0.2 0.. -1/2-1/2-1/2-1/2-1/2-1/2 2. 2. 0.0.0.2. 0.0. 0.. -1/2 SUE1 20-0 2..0.0. 0.2.2 0.0. 0..2.0 2...0.0..0.2..0.0 1.2. 1..0 2...0.0 1.0.0.2 1.0.0.0 1. 2. 2.2.0 2. 1.0.0.0 1.1.0.2 1.2 1.0.0 1.. 2..0 2. 1.2.0.0 1.2.0.2 1..0 1.. 2. 1 2-1/2 1 1 1 1 1 1 1 1 2 2 2 2 2 2-1/2 dd F to part number for rip Free set-ups. Example: SUF. Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, 1/J and 1/J Series Performance ata Flat (External Mix) Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure * Liquid* imensions (ft.).0..0 1.0....1...2. -1/2-1/2 1.0....1 2.... 0.2.2 2-1/2 SUE2 2-..1 2.... 0..0.2.0 2.........2....... 0..0 0.2.1-1/2-1/2-1/2-1/2.. 0..0 0..0 0.. 0.2. -1/2-1/2 0..0.... 0.. 0.2. 0-1/2-1/2-1/2 1 SUE2 1-.0..2.0.......2.0.0.. 1.0......1.2. 1.0.. 2.... 0...2 1.2......1.. 0.2 1.0 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2-1/2 1 1 1 1 tomizing.0..0.1.1 2.... 0 1..2-1/2-1/2 1.0.. 2.1..... 1.. 2-1/2-1/2 SUE2 0 2-..1.1... 0..0 0 1..1 2...1..... 1..0...1. 0..0 0..0 0 1.. -1/2-1/2-1/2-1/2-1/2.. 0.1.0.. 0.. 0 1.. -1/2-1/2 1 0..0.1. 0..0 0.. 1. 1.1 1 SUE2 SUE2 0 1-0 1-.0..2.0.1. 1.0.... 0 1.. 1.0...1. 2....0 1.... 2.1..... 1. 1. 2...1...1.. 1. 1..0.. 1.0.. 2 1.0. 2..0.0 1.2 1.0.... 1.0. 0 2...0 1..... 1.0.1 0 2...0 1. 2.... 1.0.0 0 2. 1.0 0.0 1. 1 2 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 1 2 1-1/2-1/2 1 1 1 1 1 dd F to part number for rip Free set-ups. Example: SUF. Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, 1/J and 1/J Series tomizing Performance ata Flat (External Mix) SUE2 0 2- Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0.. 2.. 1.0. 2...0.0..1.. 1.0. 0 2..0.0. 2.... 1.0. 2...0..... 0 1.0.0 2.. 0.0.1.... 1.0. 0 2..0 0.0... 0..0 0 1.0.0 0 2.. 0.0. 0..0.. 0 1.0. 0 2.. 0.0 1.0 * 1 0 0 Liquid* imensions -1/2-1/2-1/2-1/2-1/2-1/2 1-1/2 1 1-1/2 1 (ft.) -1/2 1-1/2 SUE 10 02-2.0. 2.. 1.0. 2...0.2..2 1.0. 2. 1..0... 1.0. 2. 1.0.0... 0 1.0. 0 2. 1..0... 1.0. 2..0 0.0. 0.. 1.0 1. 0 2..2.0 1.. 1. 0 1.0 1. 0 2..2 2 0 0 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1-1/2 1 SUE 010 02-1..2.. 1.. 0. 1. 1.... 1. 1...0 1.. 0.. 1. 1.0 0..2 1.... 0 1. 1... 0 1... 1. 1..0 0..2 1. 1. 0. 1. 0 1..2 0 1. 1. 0..2 0 1..2 0 0 0 1-1/2-1/2-1/2-1/2 1 1 1-1/2 1 1 1 1 SUE 010 02-2.. 0.0. 0. 1.0 0 2.0.2 2...0. 0 0. 1. 2.0. 0 2...0 1. 0..0 0 2.0.2 2...0 1.0 0 0..2 2. 1. 0.0 1. 0.. 2. 1.0.0.0 0 0..2 0 2. 1. 0.0.2 0 0 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 1 1 1 1 1 1 1 1 dd F to part number for rip Free set-ups. Example: SUF. Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, High Transfer Efficiency (HTE), 1/J Series Features and enefits new air cap design enables the use of lower air pressures to achieve the same spray performance as conventional external mix set-ups. Flat spray pattern HTE set-ups operate at pressures as low as psi (0. bar). large air chamber directly feeds the air exit orifices. esign provides high liquid transfer efficiency, minimal air loss, and minimal misting. consumption is reduced and maximum spray coverage on the target is achieved. See also Section G, utomatic s Round spray pattern " (1 cm) " (2 cm) 1" ( cm) " (1 cm) " (2 cm) 1" ( cm) retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. HTE air cap produces a flat spray and a round spray. Performance ata tomizing Flat (External Mix) SU-HTE SU-HTEE SU-HTEF PF20 LP2- PF0 LP2- PF1 LP2- Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0.0..0.2..0.0..0.2..0.1..0.0.2.0.2.2.0.1.2.0.0.2.0.0..0.2..0.1..0.0..0.2. 1.0.0. 1.0.2. 1.0.1. 1.0.0. 1.0.2..0 1. 2..0 2.2 2..0 1...0 2.2..0 2...0 1...0 2.2..0 2...0.1..0 1..2.0 2.2.2.0 2..2.0.1.2.0 1...0 2.2..0 2...0.1..0.. 1.0 1.. 1.0 2.2. 1.0 2.. 1.0.1. 1.0...0 1.0 2..0 1.0 2..0 1.0..0 1...0 1...0 2.0..0 1.0..0 1...0 1...0 2.0..0 1.0.2.0 1..2.0 1..2.0 2.0.2.0 2..2.0 1.0..0 1...0 1...0 2.0..0 2.. 1.0 1.0. 1.0 1.. 1.0 1.. 1.0 2.0. 1.0 2.. dd F to part number for rip Free set-ups. Example: SU-HTE-F. The operating pressures and flow rates are based on spraying water and air at room temperature. djustments may need to be made to accommodate other liquids with different characteristics. * Liquid* 1 1 1 1 1 1 imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 2 1 2 2 2 2 2 2 2 Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, High Transfer Efficiency (HTE), 1/J Series tomizing Performance ata Flat (External Mix) SU-HTE1 SU-HTE1 SU-HTE1E SU-HTE1F SU-HTE2 SU-HTE2E PF LP- PF20 LP- PF0 LP- PF1 LP- PF20 LP2-0 PF0 LP2-0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0...0..2.0..2.0...0...0...0...0.1..0...0...0.1..0...0.. 1.0..2 1.0..2 1.0.1.2 1.0..2 1.0..2.0.0..0.0.2.0.2.2.0.0..0.2..0.1..0.0..0.2..0.1..0.0..0.2..0.1..0.0..0.2. 1.0.0.2 1.0.2.2 1.0.1.2 1.0.0.2 1.0.2.2.0 1. 2..0 1...0 1..2.0 2.2.2.0 2..2.0 1...0 2.2..0 2...0.1..0...0 1...0 2.2..0 2...0.1..0...0 1...0 2.2..0 2...0.1..0.. 1.0 1..2 1.0 2.2.2 1.0 2..2 1.0.1.2 1.0..2.0 1.0 2..0 1.0..0 1...0 1.0.2.0 1..2.0 1..2.0 2.0.2.0 1.0..0 1...0 1...0 2.0..0 2...0 1.0..0 1...0 1...0 2.0..0 2...0 1.0..0 1...0 1...0 2.0..0 2.. 1.0 1.0.2 1.0 1..2 1.0 1..2 1.0 2.0.2 1.0 2..2.0.0 2.0.0.0 2..0.2 2..0.0 2..0.2 2..0.1 2..0.0..0.2..0.1..0.0..0.0..0.2..0.1..0.0..0.2..0.0.0.0.2.0.0.1.0.0.0.0.0.2.0 1.0.0. 1.0.2. 1.0.1. 1.0.0. 1.0.2..0 1. 2.0.0 1. 2..0 1. 2..0 2.2 2..0 1...0 2.2..0 2...0.1..0 1...0 2.2..0 2...0.1..0...0 1..0.0 2.2.0.0 2..0.0.1.0.0..0 1.0 1.. 1.0 2.2. 1.0 2.. 1.0.1. 1.0.. dd F to part number for rip Free set-ups. Example: SU-HTE-F. The operating pressures and flow rates are based on spraying water and air at room temperature. djustments may need to be made to accommodate other liquids with different characteristics. * Liquid* 1 1 1 1 1 1 1 1 1 1 1 1 imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1-1/2-1/2 1-1/2-1/2 1 1 1 1 1 1-1/2-1/2-1/2 1-1/2-1/2-1/2 2 2 1 2 2 2 2 2 0 2 2 2 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, High Transfer Efficiency (HTE), 1/J Series Performance ata Flat (External Mix) Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1 * Liquid* imensions SU-HTE2F PF1 LP2-0.0 1.0 2.0.0 1.0 2..0 1. 2..0 1.0 2..0 1. 2..0 1. 2..0 2.0 2..0 1.0..0 1...0 1...0 2.0..0 2...0 1.0..0 1...0 1...0 2.0..0 2...0 1.0.0.0 1..0.0 1..0.0 2.0.0.0 2..0 1.0 1.0. 1.0 1.. 1.0 1.. 1.0 2.0. 1.0 2.. 1 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 2 2 2 2 2 2 SU-HTE SU-HTE PF LP1- PF20 LP1-.0..0.0...0...0...0...0...0...0.1..0...0...0.1..0...0.. 1.0..1 1.0..1 1.0.1.1 1.0..1 1.0..1.0.0.0.0.0..0.2..0.0..0.2..0.1..0.0..0.2..0.1..0.0..0.2..0.1..0.0..0.2. 1.0.0.1 1.0.2.1 1.0.1.1 1.0.0.1 1.0.2.1 1 1 1 1 1-1/2 1 1 1 1 1 1 1 2 1 0 1 tomizing SU-HTEE PF0 LP1-.0 1..2.0 1..0.0 1...0 2.2..0 2...0 1...0 2.2..0 2...0.1..0...0 1...0 2.2..0 2...0.1..0...0 1...0 2.2..0 2...0.1..0.. 1.0 1..1 1.0 2.2.1 1.0 2..1 1.0.1.1 1.0..1 1 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 2 2 2 SU-HTEF PF1 LP1-.0 1.0.2.0 1.0.0.0 1..0.0 1.0..0 1...0 1...0 2.0..0 1.0..0 1...0 1...0 2.0..0 2...0 1.0..0 1...0 1...0 2.0..0 2...0 1.0..0 1...0 1...0 2.0..0 2.. 1.0 1.0.1 1.0 1..1 1.0 1..1 1.0 2.0.1 1.0 2..1 1 1-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 2 2 2 2 2 dd F to part number for rip Free set-ups. Example: SU-HTE-F. The operating pressures and flow rates are based on spraying water and air at room temperature. djustments may need to be made to accommodate other liquids with different characteristics. Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, High Transfer Efficiency (HTE), 1/J Series tomizing Performance ata Round (External Mix) SU-HTE1 SU-HTE1 SU-HTE1 PF20 LP- PF0 LP- PF1 LP- Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1.0.0 1..0.0 2..0.2 2..0.0 2..0.2 2..0.1 2..0.0 2..0.2 2..0.0..0.2..0.1..0.0..0.2..0.0..0.2..0.1..0.0..0.2..0.0.1.0.2.1.0.1.1.0.0.1.0.2.1 1.0.0. 1.0.2. 1.0.1. 1.0.0. 1.0.2..0 1. 1..0 1. 2..0 1. 2..0 2.2 2..0 1...0 2.2..0 2...0.1..0 1...0 2.2..0 2...0.1..0 1..1.0 2.2.1.0 2..1.0.1.1.0..1 1.0 1.. 1.0 2.2. 1.0 2.. 1.0.1. 1.0...0 1.0 2..0 1.0 2..0 1. 2..0 1.0..0 1...0 1.0..0 1...0 1.0.1.0 1..1.0 1..1.0 2.0.1 1.0 1.0. 1.0 1.. 1.0 1.. 1.0 2.0. dd F to part number for rip Free set-ups. Example: SU-HTE-F. The operating pressures and flow rates are based on spraying water and air at room temperature. djustments may need to be made to accommodate other liquids with different characteristics. * Liquid* 1 1 1 1 1 1 imensions 1-1/2 2 2 2-1/2 1-1/2 1 2 2-1/2 2 2 2-1/2 2 2-1/2 2-1/2-1/2-1/2-1/2 2-1/2 2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 2 2 2 2 2 Ordering Info Nozzle ody* omplete Nozzle ssembly 1/ J SS SU-HTE SS l l l l l Inlet onn. Nozzle ode Number ode Only HTE SS l l Number ode SPT connections require the addition of a prior to the nozzle body inlet connection. *To order fluid cap only, use fluid cap number (shown in performance data charts and material code). To order air cap only, use air cap number (shown in performance data charts and material code). To order spray nozzle without set-up, use inlet connection, nozzle body and material code. To order rip Free set-ups, add F after set-up number: SU-HTE-F SS. Phone 1-00--spray, FX 1---spray F

Siphon/Gravity-Fed s, External Mix, 1/J and 1/J Series s Round spray and flat spray air caps produce round spray and flat spray patterns. Features and enefits For round and flat sprays, angle is maintained throughout distance. eyond, the spray becomes turbulent and will project out to distance. When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or a gravity-feed. esigned to draw liquid through the feed line into the air flow where it is atomized. Round spray pattern retainer ring and gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. Refer to page F for Siphon/Gravity-Fed s diagram. Performance ata Flat tomizing tomizing apacity Gravity Head Liquid apacity (gallons per hour)* Siphon Height 1 * imensions at " Siphon Height (ft.) SUF1 20.0.....2.2..1. 1.2.1..2.2.2.2.1.1 1..1.1.1..0-1/2-1/2-1/2 1 1 1 SUF2 2 1. 1.01..0..2..2. 2.2...1..1... 2......1....0..1....2-1/2-1/2-1/2-1/2-1/2 1-1/2 1 1-1/2 1 1 SUF 0 2.2 1. 1.2 1. 1.01..2..2 2. 1.2 1. 1..2..2...2..2....2. 0...2. -1/2-1/2-1/2-1/2 SUF 0 2. 2.01 1.0 1.1 1. 1. 1.2 1.1.2 2.0 2.00 1. 1.1 1. 1.2 1. 1. 1..2 1.2 1. 1. 1.2 1. 1. 1.0 0. 1.... -1/2-1/2-1/2-1/2-1/2 Phone 1-00--spray, FX 1---spray F2

Siphon/Gravity-Fed s, External Mix, 1/J and 1/J Series tomizing Performance ata Round SU1 SU1 1 0 tomizing apacity Gravity Head Liquid apacity (gallons per hour)* Siphon Height 1.0.....2.1.......1.2....0..1...2.1 1.2.....1..1..0......2..........0 1.0..1..1..1..2 1...2...... * imensions at " Siphon Height ngle ( ) 1 1 1 1 1 1 1 1 1 1 (ft.) -1/2-1/2-1/2-1/2-1/2 SU2 0 0.0.1..1....2 1...2...0.. 1....2..1... 2.0....1..1.. 1 1 1 1 1 SU2 20 0.0. 1.1 1.0.1... 1.0 1. 1.2 1..... 1.0 1. 1. 1.2 1.1 1.0.1..2 2. 1. 1.1 1. 1.0 1.02.0..2 1 1 1 1 SU 0 1 1.0.0.1.. 2. 1.0..00.0....0.00 1..0..0...0.. 2. 1. 0..0..0..0. 2. 1. 0 1 1 1 1 1 2 1 1 SU 010 10..2.0...........2.2 0.1..0..... 2.2 0 2 2 2 2 2 Phone 1-00--spray, FX 1---spray F

Overview, 1/JJ ompact Series 1/JJ Series air atomizing set-up 1/JJ 1 2 set-up 1/JJO lean-out needle assembly 1 1/JJN 1 2 1. Retainer ring P2 2. cap. Fluid cap. O-ring 1-2/00. Nozzle body P1. Nozzle body P. ack Seal Gasket 2-U Shut-off needle assembly for rip Free 1/JJU rip Free Shut-off/clean-out needle assembly tomizing pplying lubricant to form presses in steel drum manufacturing. Phone 1-00--spray, FX 1---spray F2

Nozzle odies/nozzle ssemblies, 1/JJ ompact Series tomizing Features and enefits Nozzle assembly consists of a body and spray set-up. Various assemblies can be added to provide shut-off or clean-out functions. 1/JJ has liquid and air feeds at opposite ends of the body. 1/JJN features a manual shut-off needle that enables the flow of liquid to be stopped. 1/JJO features a clean-out needle that is activated manually. Needle slides through the liquid orifice to clear obstructions. Ideal for intermittent spraying applications when liquid can dry in the orifice between uses. Optimization Tips See page F2 for optimization tips. See lso ccessories line filters pressure regulators Liquid pressure regulators Pressure gauges Solenoid valves Strainers http:// 1/JJ 1/JJN 1/JJO 1/" NPT or SPT 1/" NPT or SPT with 1/" NPT or SPT with shut-off needle clean-out needle s Ordering Info Nozzle odies Electroless Nickelplated rass ode Nozzle Type JJ JJN JJO (none) l l l Stainless Steel SS l l l s Electroless Nickelplated rass ap and Stainless Steel SSR l l l Stainless Steel SS l l l omplete Nozzle ssembly Nozzle ody* 1/ JJN SS SUJ SS l l l l l Inlet onn. Nozzle ody ssembly Type ode *Includes retainer and gasket. ode SPT connections require the addition of a prior to the nozzle body inlet connection. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: J0-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: J1-SS. To order spray nozzle without set-up, use inlet connection, nozzle body and material code: 1/JJN-SS. Only SUJ SS l l ode To order spray set-up only, use spray set-up number and material code: SU-SS. Phone 1-00--spray, FX 1---spray F2

Pressure s, Internal Mix, 1/JJ ompact Series s Features and enefits For round spray pattern, angle is maintained throughout distance. eyond, the spray becomes turbulent and will project out to distance. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. Round spray and circular spray air caps produce full cone round spray; air caps used in spray set-up SUJ produce circular spray pattern. Round spray pattern 2 retainer ring and 1-2/00 O-ring must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. Performance ata Round Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure * Liquid* imensions ngle ( ) (ft.) tomizing SUJ J0 J.0.. 1.0. 1.. 2 1.. 0 2.2..0.. 1 1.2.0 2 1.. 1.2.0 2.0 1.0.0.... 2 1.0.2 1.2. 1.0 1.1 2.2..2 1.0. 1.2 1.2 1.2.. 2. 1.1 2. 1. 0 1. 1. 2 1 1-1/2 1-1/2-1/2-1/2 SUJ J0 J1.0.. 1 1.. 1. 1.00 2. 1.. 1..0.. 1.2. 2 1. 1.1 2.1 1.2 2. 1..0.2.0 1. 1.0 2 1. 1. 1.2 1. 2 2. 1. 2.0 1.2 1. 1. 1.0 1. 2 2. 2.2 1.02 1. 1.2 1. 0 1. 2. 2 1 1 1 1 1 1 Phone 1-00--spray, FX 1---spray F2

Pressure s, Internal Mix, 1/JJ ompact Series tomizing Performance ata Round SUJ J20 J1 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1.2. 2.1 1.0 2.0 1..2 1.2.2 1.0 1.0 1.0. 2 1. 1.2 2. 1.2. 1. 2.2 1..0 1.1 1. 1. 2. 1.. 1..2 1.. 1. 1.0 1. 1.0 2.0 2 2. 2.01.0 2.0 2. 1. 2. 2.0 2 1. 2. 1. 2. 0. 2. * 2 Liquid* imensions ngle ( ) 1 1 2-1/2 (ft.) 1 1 1-1/2 SUJ J0 J1 1.0. 2. 2.0.1..2...0. 2.. 2.0.1.0.1..0.. 1.0. 2......2 0..2 2 1.2. 1.. 1.. 0 1.. 0...2. 0.. 0.. 0.2. 0.2. 1 2 2 1 2 SUJ J0 J1.0.1 2.00. 2. 1..2 1.. 2...0. 2.2.0 2..1. 2 1.... 1.0. 2..2.1..2..1 1.. 2.2. 2..0 2...2.0 2....0...0.0 2 0 0 1 1 2 1 1 1 2 2 ircular SUJ J0 J10--2-1H Use only with 1/JJU automatic air atomizing nozzles. Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 2...0 0.1..0... 2. 2... 2.2... 0.0.0 2.0 2. 2 2.... 0.1...1 2 1.. 1...2.1 0.1. 0. 1. 2 1.1.2 1.. 0 1.. 0 1. 1. circular spray pattern Phone 1-00--spray, FX 1---spray F2

Pressure s, Internal Mix, 1/JJ ompact Series s Wide angle round and flat spray air caps produce hollow cone type, wide angle round spray and flat spray patterns. Features and enefits For wide angle round and flat sprays, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. Wide angle round spray pattern 2 retainer ring and 1-2/00 O-ring must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. " (1 cm) " (2 cm) 1" ( cm) Performance ata Wide ngle Round SUJ1 SUJ2 SUJ2 SUJ2 SUJ J0 J---0 J0 J1---0 J0 J1---0 J0 J1--2-0 J0 J1--- Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1.1..0 2..2 2.. 2.. 2..1.0 1.. 1.0 1.0.0 2 2.02. 2.2.1 2.2..0..0 1.0 1.. 1.1. 1.0. 2. 1..0.. 1.1.1.1 1.0 1. 1.2 1.0 1. 2..0. 1.2 0. 1.. 2.0.0 1. 1.. 2.. 2.. 2....0. 2. 2. 2. 2.2 2. 2.0.2.. 2 1..0 2.0.0.0.0..2.0. 0 1.. 0.0.00 2.. 1...0. 1..0 1..2 2.0. 2. 1.2 2..0. 1.. 2.00 2. 2. 2. 2.2...0 2.0 2.00.1 2....1.2..2 2. 2.0 2.. 0..1.0.1 2 2.2.1 0 2..1 1.0..0..1 1.. 1..0 0........ 0..2 1..1 2.0...1.. 0.. 0 1......1 0.1. 0.2. 0 1.1..0.2 2.. 0.. 0.. 1.0. 1. 2. 1. 2.2 2... 0..0 1.0 2.1 1. 2. 2.2.0 2....0. 2.0 1. 2. 2....1.0 0..2 1. 2.0 2 1..00 2.. 1.2.2 0.00.0 2.2 2. 1.0.2 1.0. 1.0. * 2 2 2 0 0 0 0 Liquid* imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1-1/2-1/2-1/2 1 1-1/2-1/2 (ft.) -1/2-1/2 1-1/2-1/2-1/2 1-1/2-1/2 1 2 1 1 1 tomizing Phone 1-00--spray, FX 1---spray F2

Pressure s, Internal Mix, 1/JJ ompact Series tomizing Performance ata Flat SUJ J0 J2 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1.. 1.0 2.1 1. 2 2. 1. 2. 1..1 2..0 1.2. 1.2 1.1 2 2.1 1. 2 2. 2.01 2. 2..0 1.0 1.0 2 1.0 1.0 1. 1.2 2. 2.1 2.2.2 1.0. 1.2. 1. 1. 2.1 1.2 2.1 0 1... 1.. 2.1. 2. 0..2 0..2 * 1 0 Liquid* imensions 1 1-1/2 1 2 1 2 (ft.) -1/2-1/2 SUJ J20 J2.0 2.1.0... 1.2. 1.. 2..0 1.0.2 2.1 1..1 1. 2. 1. 0. 2.2 1.0 1.. 2 2.0 1. 2. 1.. 1.. 2.. 1.2 2 1. 1. 1.2 2.0 1. 2. 2... 1. 0 1.2 2.2 0..0 1.. 1 2 0 0 1 2 2 1 2 2 2-1/2-1/2 SUJ J20 J 1.0 1.0 1.0 1. 1. 2 2.0 1. 2.1 2.1. 2..0 1.1 1. 1.1 1.0 1. 1. 2. 0 2. 2.0.2 1.2.0 1.0 1. 1. 1.1 2.2 2.1. 2. 1.. 1. 0 1. 2.. 2.0 0 2 2 2 2 1 2-1/2-1/2-1/2 SUJ2 J0 J2 1.0 2. 1.2 2. 2....0..0.0 1.0 2.2 2.. 2... 0.. 0.. 1.2 2. 2..0 2.. 2.0.1.0. 1.00 2.0 2.2.....0....0 2 2 1 1 1 1 1-1/2-1/2 SUJ2 J0 J2.0.0 1.1. 1.. 2.. 2. 1...0. 1. 2. 2.02. 2. 0.... 1.0.2 1..0 2. 2. 2...1 0.. 2. 1.. 2..0.2..0 0...0.1 2..0 0..00 0.. 1 2 1 1 1 1 1-1/2-1/2-1/2 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, High apacity, 1/JJ ompact Series Features and enefits Offers an increased ability to atomize viscous fluids and allows for greater capacities of finely atomized sprays. Simple, one-piece, low-profile design permits larger air passage. More air can be brought in to atomize the liquid stream. tomization can be controlled by varying the air pressure without changing liquid flow rates. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. s External mix air caps produce a flat spray pattern. Performance ata Flat (External Mix) SUJE1-0 SUJE1-0 SUJE1-0 SUJE-0 SUJE-0 PFJ1 PJ-0 PFJ0 PJ-0 PFJ20 PJ-0 PFJ0 PJ-0 PFJ0 PJ-0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure Flat spray pattern.0 1. 2..0 1. 2..0 2.2 2..0 2. 2. 1.. 1.. 2.2. 2.. 1..0 1..0 2.2.0 2..0 1..2 1..2 2.2.2 2..2 0 1.. 0 1.. 0 2.2. 0 2...0 1. 2..0 2. 2..0.2 2..0 1.. 2...2. 1..0 2..0.2.0.0.0 1..2 2..2.2.2.0.2 0 1.. 0 2.. 0.2. 0.0..0 2. 2..0. 2..0. 2..0. 2. 2........ 2..0..0..0..0 2..2..2..2..2 0 2.. 0.. 0.. 0...0.0 2..0. 2..0. 2..0 1. 2..0..... 1...0.0..0..0 1..0.0.1..1..1 1..1 0.0. 0.. 0.. 0 1.. 0 0 0 0.2. 0 0 0 0.2. The liquid and compressed air or gas are mixed externally to produce a completely atomized spray. SUJE Series is both compact and air efficient. Offered in three spray angles 0, and 0. SUJE Series features lower spray velocity for improved transfer and reduced misting and is ideal for applications where space is limited. Very efficient use of air results in reduced air consumption costs and noise levels. Simple four-part assembly allows easy installation and maintenance. " (1 cm) " (2 cm) 1" ( cm) P2 retainer ring and P1-2/00-VI O-ring must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. The adapter is used with all 1/JJ nozzle bodies and automatic spray guns with extensions, but not on 1/JJU spray guns without extensions. Please contact your sales engineer. ngle 0 tomizing Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, High apacity, 1/JJ ompact Series tomizing Performance ata Flat (External Mix) SUJE1- SUJE1- SUJE1- SUJE- SUJE- SUJE1-0 SUJE1-0 SUJE1-0 SUJE-0 SUJE-0 PFJ1 PJ00- PFJ0 PJ00- PFJ20 PJ00- PFJ0 PJ- PFJ0 PJ- PFJ1 PJ0-0 PFJ0 PJ0-0 PFJ20 PJ0-0 PFJ0 PJ-0 PFJ0 PJ-0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0 1. 1..0 1. 1..0 2.2 1..0 2. 1. 1..0 1..0 2.2.0 2..0 1..0 1..0 2.2.0 2..0 1..0 1..0 2.2.0 2..0 0 1.. 0 1.. 0 2.2. 0 2...0 1. 1..0 2. 1..0.2 1..0.0 1. 1..0 2..0.2.0.0.0 1..0 2..0.2.0.0.0 1..0 2..0.2.0.0.0 0 1.. 0 2.. 0.2. 0.0..0 2. 1..0. 1..0.0 2..0..0..0 2..0..0..0..0 2..0..0..0..0 0 2.. 0.. 0.. 0...0.0 2.1.0. 2.1.0. 2.1.0 1. 2.1.0..... 1...0..... 1...0..... 1.. 0.0. 0.. 0.. 0 1.. 1.0. 1.0. 2.2. 0 1.0. 0 2.2. 0 2.. 0.0 1. 1..0 1. 1..0 2.2 1..0 2. 1. 1..0 1..0 2.2.0 2..0 1..0 1..0 2.2.0 2..0 1..0 1..0 2.2.0 2..0 0 1.. 0 1.. 0 2.2. 0 2...0 1. 1..0 2. 1..0.2 1..0.0 1. 1..0 2..0.2.0.0.0 1..0 2..0.2.0.0.0 1..0 2..0.2.0.0.0 0 1.. 0 2.. 0.2. 0.0..0 2. 1..0.0.0 2..0..0..0 2..0..0..0..0 2..0..0..0..0 0 2.. 0.. 0.. 0...0 2..0....0..... 0.0. 0.. 0.. 0 1.. 1.0. 1.0. 2.2. 0 1.0. 0 2.2. 0 2.. 0.2. 0 0 0 0.2. ngle 0 Phone 1-00--spray, FX 1---spray F2

Pressure s, Internal Mix, Efficient, 1/JJ ompact Series s Elliptical spray pattern Internal mix air caps produce an elliptical spray pattern. Performance ata Elliptical / Efficient (Internal Mix) SUJ0 SUJ1 PFJ2 PJ PFJ PJ2-0 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure imensions 1 2 * Liquid*. 1.1. 1.1 0.1. 0.. 0...1..1.2 1.1. 1.... 1.1. 1.. 1.2....2.1 1.. 1.. 1.. 2.. 2.0. 2 1.2. 2 1..1 2 1.. 2 2.1... 1.1. 1.. 1.. 1.. 2.2. 1.0.. 1.0 1.. 1.0 1..2 1.0 1..2 1.0 2.2.2 0 1.1 1. 0. 1.2 1.2 1.1 1. 1.0 1.1. 1..2 2.1. 2..1 2 1.0. 2 1..0 2 2.1. 2 2.. 2.0... 1.. 2.0. 2..0 2...2. 1.0 1.. 1.0 1.. 1.0 2.. 1.0 2.. 1.0.2. 1.0..2.0 1..2.0 2...0 2..2.0.2.2.0..2.0.. ngle ( ) 2 2 2 tomizing Tabulation is based on spraying air and water at room temperature under laboratory conditions. Phone 1-00--spray, FX 1---spray F

Siphon/Gravity-Fed s, External Mix, 1/JJ ompact Series tomizing s Round spray air caps produce a full cone round spray pattern. Features and enefits For round spray pattern, angle is maintained throughout distance. eyond, the spray becomes turbulent and will project out to distance. When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or a gravity-feed. esigned to draw liquid through the feed line into the air flow where it is atomized. Round spray pattern 2 retainer ring and 1-2/00 O-ring must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. Performance ata Round SUJ1 SUJ1 SUJ2 SUJ2 SUJ SUJ SUJ J1 J J0 J J0 J0 J20 J0 J20 J- J0 J1 J0 J1 tomizing apacity Gravity Head Liquid apacity (gallons per hour)* Siphon Height 1.0... 1.2.......0......2..1..1.1..1..2....2.1 SUJ1.1..0......2. SUJ1.........0 1.0..1..1..1..2 1...2.......0.1 1. 1. 2.0.....1.2.....2.....1..0.1..2...1... SUJ2...0. 1.1 1.0.1... SUJ2 1.0 1. 1.2 1..... 1.0 1. 1.1 1. 1.0 1.02.0..2 2. 1. 1. 1.2 1.1 1.0.1..2.0.1.1. 1. 1. 1.1 1. 1. 1.1 1.0 1. 1.2.. 1. 1... 1. 1..2. 1. 1..2.0 1.02 SUJ...0 1. 1... SUJ 1. 2. 2. 1.0 1.0 1.... 2. 2.0 2. 2.02 1.0..2.2...0 2. 2.2 2.0 1.1.2 0 1.0.00...0.0.0.0.1.......0...0. 2..0..0 1.0.00... 1. 2. 2. SUJ.0 1. 1. 0 * imensions at " Siphon Height ngle ( ) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 (ft.) -1/2-1/2-1/2-1/2-1/2 1 1 1 1 Phone 1-00--spray, FX 1---spray F

Siphon/Gravity-Fed s, External Mix, 1/JJ ompact Series s Features and enefits For flat spray pattern, dimensions, and are the pattern widths at distances from the nozzle. Total distance of spray projection from the nozzle to the maximum dispersal point is represented by. Flat spray air caps produce a flat spray pattern. Flat spray pattern " (1 cm) " (2 cm) 1" ( cm) Performance ata Flat tomizing apacity Gravity Head Liquid apacity (gallons per hour)* Siphon Height 1 * imensions at " Siphon Height (ft.) tomizing SUJF1 J20 J.0.....2.2..1. 1.2.1..2.2.2.2.1.1 1..1.1.1..0-1/2-1/2-1/2 1 1 1 SUJF2 J J2 1. 1.01..0..2..2. 2.2...1..1... 2......1....0..1....2-1/2-1/2-1/2-1/2-1/2 1-1/2 1 1-1/2 1 1 SUJF J0 J 2.2 1. 1.2 1. 1.01..2..2 2. 1.2 1. 1..2..2...2..2....2. 0...2. -1/2-1/2-1/2-1/2 SUJF J0 J 2. 2.01 1.0 1.1 1. 1. 1.2 1.1.2 2.0 2.00 1. 1.1 1. 1.2 1. 1. 1..2 1.2 1. 1. 1.2 1. 1. 1.0 0. 1.... -1/2-1/2-1/2-1/2-1/2 Phone 1-00--spray, FX 1---spray F

Overview/Nozzle odies/nozzle ssemblies, VU and VMU Series tomizing 1/V 1/VN 1/VO Variable Series air atomizing nozzles set-up 1 2 Plug -001-SS Shut-off needle assembly 2-001-SS lean-out needle assembly 1/VNO 1. ap ring 2-1-SS 2. cap. Fluid cap. Nozzle body 20-001-SS. Washer 2-001-U Shut-off/clean-out needle assembly 1/VU Features and enefits The V, VU and VMU variable spray nozzles provide uniform spray distribution, even when spraying viscous liquids. Independent control of liquid, atomizing air, and fan air pressures is possible for fine-tuning of flow rate, drop size, spray distribution and coverage. an be set and re-set in seconds, simplifying application changes. Independent air atomizing line can be adjusted to vary spray drop size without affecting liquid flow rates. dditional inlet/outlet port allows for liquid recirculation that effectively maintains the flow of viscous liquids. V offers continuous operation and consists of a body, spray set-up and plug. VN features a manual shut-off needle that enables the flow of the liquid to be stopped. VO features a clean-out needle that clears the liquid orifice of obstructions when activated manually. VNO combines the features of the VN and VO, offering a combination shut-off/clean-out needle. VU offers automatic operation with a built-in shut-off/clean-out needle. VUPM has the same operating features as the VU, but offers the convenience of a mounting plate. VMU allows for individual adjustment of the atomizing air, fan air and liquid flows and offers modular components to accommodate a wide range of spray applications. Mounting Kit -001-1SS uses clamps to mount V nozzles. Mounting Kit -002-SS uses rods to mount V nozzles. Optimization Tips See page F2 for optimization tips. See lso ccessories line filters pressure regulators Liquid pressure regulators Pressure gauges Solenoid valves Strainers http:// Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, VU and VMU Series VMU V VN VO 1/" NPT or SPT with shut-off/clean-out needle VNO 1/" NPT or SPT 1/" NPT or SPT with 1/" NPT or SPT with shut-off needle clean-out needle Mounting Kits VU 1/" NPT or SPT with shut-off/clean-out needle VUPM lamp mounting kits s Rod mounting kits 1/" NPT or SPT tomizing 1/" NPT or SPT ode Nozzle Type VMU V VN VO VNO VU VUPM Stainless Steel SS l l l l l l Stainless Steel/luminum SS l 1 Stainless Steel l /s Stainless Steel SS l l l l l l Other materials available upon request. Ordering Info omplete Nozzle ssembly Nozzle ody* 1/ V SS SUV SS l l l l l Inlet onn. Nozzle ody ssembly Type ode ode *Includes retainer and gasket. SPT connections require the addition of a prior to the nozzle body inlet connection. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: VF1-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: V2--SS. To order spray nozzle without set-up, use inlet connection, nozzle body, and material code: 1/V-SS. Order mounting kits separately: -001-1SS. Only SUV SS l l ode To order spray set-up only, use spray set-up number and material code: SUV-SS. Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, VMU Series tomizing Performance ata VMU SUVM SUVM VMF1 VM2- VMF0 VM2-.0 1.0 0 0 0 0.0 1.0 0 0 0 0 acity* apacity tomizing... 1.1 1. 1. 1. 2.0 2. 2.... 1.1 1. 1. 1. 2.0 2. 2. Fan 2.0 2..1.......0 2.0 2..1.......0 Liquid apacity* 1.0.0.0.0 1.0 1.0.0.0.0 1.0 ap... 1.0 1. 1. 1.. 1.1 1. 2.1 2. 2. tom..0.0 Water overage at Indicated istance from Nozzle Fan Pressure 0.0 2.0.0.0.0.0.0.0.0.0.0.0.0..0.0.0 2....0.0.0.0.0.0.0.0.0..0..0.0.0.0.0.0.0.0.0...0.0 2.0.0..0.0.0.0.0.0.0.0.0.0..0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0..0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0..0.0.0.0.0 2.0.0..0.0.0.0.0.0.0.0.0..0.0.0.0.0.0 2.0.0..0..0.0..0.0.0.0...0.0.0.0 2.0.0.0..0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 2...0...0.0.0.0.0.0.0.0..0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0..0.0.0.0 2.0.0..0..0.0.0.0.0.0.0.0..0.0.0.0.0 2...0.0..0.0.0.0.0.0.0.0..0.0.0.0.0 2..0.0..0...0.0.0.0.0.0..0.0.0.0 2.0.0...0.0.0.0.0.0.0.0.0...0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0..0..0 2....0.0..0.0.0.0.0.0..0.0.0.0.0.0.0.0.0.0.0.0...0 2.0.0..0.0.0.0.0.0.0.0.0.0.0..0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0..0.0.0.0.0.0.0.0.0...0.0.0.0.0 2.0.0..0..0.0..0.0.0.0.0.0.0.0.0.0 2.0.0.0..0.0.0.0.0.0.0.0.0.0.0.0.0.0.0 2...0...0.0.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0..0.0.0.0.0.0.0.0..0.0.0 2.0.0..0..0.0.0.0.0.0.0.0...0.0.0.0 2...0.0..0.0.0.0.0.0.0...0.0.0.0.0 2..0.0..0...0.0.0.0.0..0.0.0.0.0 2.0.0...0.0.0.0.0.0.0.0..0.0.0.0.0 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, VMU Series Performance ata VMU acity* apacity tomizing Fan Liquid apacity* ap. tom. Water overage at Indicated istance from Nozzle Fan Pressure 0 SUVM SUVM1 VMF20 VM2- VMF VM-.0 1.0 0 0 0 0.0 1.0 0 0 0 0... 1.1 1. 1. 1. 2.0 2. 2. 1. 2.0 2.....2...2 2.0 2..1.......0......0.. 1. 1. 1.0.0.0.0 1.0 1.0.0.0.0 1.0 1.2 2.2 2..0.. 2.1....0..0.0.0 2.0.0.0.0.0.0.0.0 1.0.0.0.0.0..0 1.0.0 1.0 1.0 1.0 1.0.0.0 1.0.0 1.0 2 1.0 1.0 2.0 2..0..0.0.0..0.0.0.0.0...0.0.0.0.0.0.0.0.0.0 1.0.0 1.0 1.0.0.0.0.0.0.0.0.0.0.0.0 1.0.0 1.0.0 1.0 1.0 2.0 2..0..0.0.0.0.0.0.0.0.0.0...0.0.0.0.0.0.0.0.0 1.0.0.0 1.0.0.0.0.0.0.0.0.0.0.0.0 1.0.0 1.0 1.0 1.0.0 2...0.0.0..0.0.0.0.0.0...0.0.0.0.0 2.0.0....0.0.0.0.0.0 1.0.0.0..0.0 1.0..0.0.0.0..0.0 1.0.0. 1.0.0 1.0.0 2....0..0.0.0.0.0.0.0....0.0.0.0 2.....0..0.0..0.0.0..0.0.0.0.0 2.0.0..0..0.0.0.0.0.0.0.0.0 1.0.0.0 1.0.0.0..0.0.0 1.0.0.0.0.0.0.0 1.0.0.0 1.0.0.0.0 1..0 1..0 1. 2.0.0.0.0.0.0.0.0..0.0.0..0..0.0.0.0.0.0.0.0 1.0.0.0.0.0.. 1..0 2.0 2...0.0.0.0.0.0.0.0.0.0..0..0.0.0.0.0.0..0.0.0.0 1..0.0.0.0..0.0..0.0.0.0 1.0.0 2.0 2..0.0.0.0...0.0..0.0.0.0...0.0 2....0.0..0.0.0.0. 1.0.0.0.0.0..0.0 2.0.0.0..0...0.0.0.0 1..0. 1.0....0 2.0 2..0 2.0.0.0.0..0.0.0.0...0...0.0 2..0..0..0..0..0.0.0.0.0 1.0.0.0 1.0.0 2..0.0.0.......0.0.0. 1.0.0.0 1.0 tomizing SUVM1 VMF VM-.0 1.0 0 0 0 0 1. 2.0 2.....2...2......0.. 1. 1. 1.0.0.0.0 1.0 2....0.0..0.0 2.0 2..0.0. 1.0.0 1.0 1.0.0. 1.0.0.0. 1.0.0 1.0.0.0.0 1.0.0 1.0 2.0 2.0.0.0..0.0.0.0 1.0.0.0 1..0 2.0.0.0.0.0.0..0 1.0.0 1.0 1..0...0.0.0 1. 1.0 1.0.0 2.0 2..0.0.0.0.0.0..0.0 1.0.0.0.0.0 1. 2..0.0..0.0.0..0. 1.0.0.0 1...0.0.0..0.0.0..0. 1.0..0 1.0 1.0..0 1.0.0 1. 2...0.0.0...0.0.0 1.0.. 1.0..0..0 1. 2..0..0.0.0.0..0.0 1.0..0 1.0..0 1.0.0 2.0.0.0....0.0..0.0 1.0.0.0 1.0.0.0 1.0.0 2.0.0.0..0.0.0..0.0.0.0.0.0 1.0.0..0.0 2.0.0.0.0..0.0..0.0. 1..0. 1.0.. 1..0 2.0.0.0..0.0.0.0.0.. 1...0 1.0.. 1. Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, VMU Series tomizing Performance ata VMU SUVM SUVM VMF0 VM- VMF0 VM-.0 1.0 0 0 0 0.0 1.0 0 0 0 0 acity* apacity tomizing 1. 2.2 2....0....0 2.1 2..2.1.0...0.. Fan...0.1.2. 1. 1.2 1.2.1.2.... 1.0 1.0.1 Liquid apacity* 1.0.0.0.0 1.0 1.0.0.0.0 1.0 ap.... 1. 2.2. 1.2..2. tom..0.0 Water overage at Indicated istance from Nozzle Fan Pressure 0 1 2 1.0.0..0 1.0.0 1.0.0.. 1.0.0 1.0. 1.0.0 1.0.0.0.0.0 1.0 2 1.0 1.0. 1.0 1.0.0..0.0.0 1...0 1..0.0.0.0..0.0.0.0..0. 1.0.0.0..0 1..0.0 1.0.0....0.0 1..0 1..0 1. 2.0 1.0 2 1.0 1..0..0.0..0.0.0.0.0.0.0.0 1.0..0 1.0.0 2.0.0.0..0..0.0 1.0..0 1.0.0.0 1.0.0.0 1..0 1.0.0.0..0..0.0 1.0..0 1.0.0...0 1.0 1.0 2.0.0..0.0.0.0.0.0.0.0 1.....0.0 1.0.0 2..0..0.0.0...0.0.0 1.0.0.0 1.0.0. 1.0.0 2.0.0.0.0.0.0.0.0 1.0.0.0 1.0.0.0.0. 1.0.0.0.0..0.0..0.0..0.0..0...0 1.0.0.0.0.0....0..0.0.0.0.0.0 1.0.0.0 1..0 2...0.0...0.0.0..0..0.0 1.0.0.0 1.0 1.0..0.0 1.0 2.0 1.0 2.0 1.0.0 1.0..0.0 1. 2.0 2.0 1. 1.0 2.0.0 1.0 2. 1. 2 1.0 1.0.0.0.0..0 1..0 1.0.0.0.0.0.0.0.0. 1.0.0.0.0 1....0 1...0 2.0.0..0 1. 2.0 1. 2 1.0 2 1.0 2..0.0.0.0.0..0 1.0.0. 1..0.0 1.0.0.0 1..0.0.0..0.0 1.0...0.0 1.0.0 1...0..0 1.0.0.0.0...0 1.0 1.0 2.0.0.0.0.0.0.0.0.0.0.0 1.....0.0 1.0.0.0..0.0.0 1.0.. 1.0.0.0 1.0.0 1.0.0.0.0.0.0..0 1.0.0.0.0 1.0 2 1.0 1. 2.0.0.0.0.....0.0.0..0..0.0 1.0.0 2.0.0..0.0..0..0.0.0..0.0 1.0.0.0 1..0.0.0.0.0.0.0.0.0 1.0.0.0 1.0 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, VU Series s Features and enefits Fan air tomized liquid Fan air External mix with fan air: flat spray pattern Without fan air: round spray pattern. Performance ata The dimensions, and of the flat spray pattern are controlled by the combination of fan air pressure and atomizing air pressure. The liquid flow rate is constant and not affected by the air pressure. Flat spray pattern " (1 cm) " (2 cm) 1" ( cm) 2-1-SS cap ring and 2-001-U must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. VU SUV SUV SUV VF1 V2- VF0 V2- VF20 V2-.0 1.0 0 0 0 0.0 1.0 0 0 0 0.0 1.0 0 0 0 0 acity* tomizing...2.2 1.0 1. 1. 1. 2.0 2.2...2.2 1.0 1. 1. 1. 2.0 2.2...2.2 1.0 1. 1. 1. 2.0 2.2 Fan 2.2 2......... 2.2 2......... 2.2 2......... Liquid apacity*.0.0.0.0.0.0 1.0 1.0.0.0.0.0.0.0 1.0 1.0.0.0.0.0.0.0 1.0 1.0 ap... 1.0 1.0 1. 1. 1. 1. 1. 1. 1.1 1.1 1. 1. 2.1 2.1 2. 2. 2. 2. 2.2 2.2 2. 2..0.0.... tom..0.0.0 overage (inches) at Indicated istance from Nozzle Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total air capacity is the sum of the atomizing air and the fan air. For instance, for atomizing air at psi and fan air at psi, the total is equal to.. for a total of.. t 0 psi fan air pressure the spray forms a round spray pattern. Request ata Sheets M-V, M-V and M-V. set-ups are interchangeable, but each set-up uses a different needle size. Water Fan Pressure 0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0 2.....0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0..0.0.0.0.0.0.0.0.0.0 2.0 2...0..0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0 1.0....0 2...0.0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0..0.0.0.0.0.0.0.0 1.0.0 2...0.0.0.0.0.0.0.0.0.0.0 2..0.0..0.0.0.0.0.0.0.0 2.0.0..0.0.0.0.0 1.0.0.0 1.0.0 2.0.0.0.0.0.0...0.0.0.0.0 2....0.0 1.0.0.0 1.0.0.0.0 2.0.0.0.0.0 1.0.0.0.0.0 2.0.0...0.0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0 1.0 1.0....0 2....0..0.0.0.0.0.0.0.0 2.0.0.0......0.0.0 1.0 2.0.0..... 1.0 1.0.0.0 1.0.0 2...0...0.0..0.0.0.0.0 2....0.0..0.0.0.0.0.0 2.0.0.....0.0 1.0.0.0 1.0.0 2.0.0.0.0.0 1.0.0.0.0.0.0.0.0 2.0 2..0.0 1.0.0 2.0.0 1.0.0 2..0..0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0 1.0.0.0.0.0.0.0 2.0 2..0.0.0.0 1.0.0 2...0.0.0.0.0.0.0.0.0.0.0 2.0.0.0.0.0.0.0.0 1.0.0.0.0 2.0.0.0.0.0..0 1.0.0 1.0.0 2....0.0.0.0.0.0.0.0.0.0 2....0.0..0.0 1.0.0.0 1.0 2.0.0..0.0.0.0 1.0.0 1.0 tomizing Phone 1-00--spray, FX 1---spray F1

Pressure s, External Mix, VU Series tomizing Performance ata VU SUV1 SUV1 SUV SUV VF V- VF V- VF0 V2- VF0 V2-.0 1.0 0 0 0 0.0 1.0 0 0 0 0.0 1.0 0 0 0 0.0 1.0 0 0 0 0 acity* tomizing 1. 2.0 2..2.0....0. 1. 2.0 2..2.0....0. 1. 2.0 2..1....2.0. 1. 2.2 2.....2.0.. Fan....2....0 1. 1.2....2....0 1. 1.2...0.1.2.. 1. 1.2....... 1. 1.2 1. Liquid apacity*.0.0.0.0.0.0 1.0 1.0.0.0.0.0.0.0 1.0 1.0.0.0.0.0.0.0 1.0 1.0.0.0.0.0.0.0 1.0 1.0 ap........0.0.......0.0.0.0...0.0.0.0 1. 1. 2 2 2 2 1. 1. 1 1 tom..0.0.0.0 Water overage (inches) at Indicated istance from Nozzle Fan Pressure 0.0 2...0.0.0 1.0.0 2.0.0..0.0 1.0.0.0 1.0 1.0 2.0 2..0.0.0.0.0.0.0 1.0.0 1.0 1.0.0 2...0.0.0.0.0 1.0 1.0 2 2....0.0.0.0 1.0 1.0 2.0 2..0.0....0.0.0.0.0 1.0.0 2...0.0.0..0.0 1.0 1.0 1.0 2...0.0..0.0 1.0 1.0 2.0 2...0.0.0.0.0.0.0.0.0 1.0.0 2....0.0.0.0.0.0.0 1.0 1.0 2....0..0.0.0 1.0.0 1.0.0.0.0.0.0.0 1.0.0.0.0 1.0 2.0.0 1.0 2.0 2...0.0.0.0.0 1.0 1.0.0 1.0 1.0.0 2...0..0.0.0 1.0 2 1.0 2 2.0.0.0..0.0.0 1.0 2 1.0 2 2.0 2...0..0.0.0.0 1.0.0.0 1.0.0 2....0.0.0.0 1.0.0 1.0 1.0 2.....0.0.0 1.0 1.0.0 2...0 2..0.0.0.0.0.0.0 1.0.0 2....0.0.0.0.0 1.0.0 1.0 2....0.0.0.0.0 1.0.0 1.0 2.0.0.0.0.0.0.0.0 2 1.0 2.0.0.0.0.0.0.0.0.0 1.0 1.0 2.0 2...0.0.0..0 1.0 1.0 2.0 1.0 1.0 1.0.0.0.0...0.0.0.0 1.0.0 1.0.0 2...0.0.0.0.0.0.0 1.0 2 2...0.0.0.0.0.0 1.0.0 1.0.0.0.0.0.0.0.0.0.0.0.0.0 1.0.0.0.0.0...0.0.0 1.0.0 1.0.0..0.0.0..0.0 1.0.0 1.0.0.0.0.0.0.0 1.0.0 2 1.0.0.0.0.0.0..0.0 1.0 2.0.0.0.0.0 1.0 1.0 2 2.0 1.0 1.0 2.0.0.0..0.0.0.0 1.0 1.0 1.0.0.0..0....0 1.0 1.0 2.0.0.0 1.0 2.0.0.0.0.0.0.0.0.0 1.0.0 1.0.0.0.0..0...0.0 1.0.0 1.0 2 2..0.0...0.0.0 1.0.0 1.0 Since the pressures of the air and liquid lines are independently controlled, any combination of these air and liquid pressures can be used. The total air capacity is the sum of the atomizing air and the fan air. For instance, for atomizing air at psi and fan air at psi, the total is equal to.. for a total of.. t 0 psi fan air pressure the spray forms a round spray pattern. Request ata Sheets M-V1, M-V1, M-V and M-V. set-ups are interchangeable, but each set-up uses a different needle size. Phone 1-00--spray, FX 1---spray F2

Nozzle odies/nozzle ssemblies, 1/2J Series 1/2J 1/2J Series air atomizing nozzles 1/2J Plug P10 set-up 1/2JN 1/2" NPT or SPT 1/2JN 1/2JO 1 2 1. Retainer ring P10 2. cap. Fluid cap. Fluid cap gasket P1. Nozzle body P101 Shut-off needle assembly lean-out needle assembly 2 1/2" NPT or SPT with shut-off needle 1/2JO 1/2" NPT or SPT with clean-out needle Features and enefits 1/2J air atomizing series ranges in capacity from.1 to (1. to l/h). The nozzles are available with shut-off and clean-out needles. 1/2J body has liquid and air feeds at opposite ends of the body and is provided with a removable plug so other needle assemblies may be added in the future. 1/2JN features a manual shut-off needle that enables the flow of liquid to be stopped. 1/2JO features a clean-out needle that is activated manually. The needle slides through the liquid orifice to clear obstructions. Ideal for intermittent spraying applications when liquid can dry in the orifice between uses. tomizing Optimization Tips See page F2 for optimization tips. See lso http:// ccessories line filters pressure regulators Liquid pressure regulators Pressure gauges Solenoid valves Strainers s Ordering Info Nozzle odies ode Nozzle Type J JN JO Nickel-plated rass (none) l l l Stainless Steel SS l l l s Nickel-plated rass and Stainless Steel SSR l l l Stainless Steel SS l l l omplete Nozzle ssembly Nozzle ody* 1/2 JN SS SU SS l l l l l Inlet onn. Nozzle ody ssembly Type ode ode *Includes retainer and gasket. SPT connections require the addition of a prior to the nozzle body inlet connection. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: 20-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: ---0. Only SU SS l l ode To order spray set-up only, use spray set-up and material code: SU-SS. Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, 1/2J Series tomizing Features and enefits J features the center lines of the air and liquid inlet entering in the back of the nozzle and parallel to the spray projection axis. 1/2JJ features a steam jacket around the nozzle body for spraying liquids that are too viscous to spray at room temperature. 2J is a dual spray assembly with opposing spray set-ups perpendicular to opposing air and liquid inlets. Thick wall adapters replace retainer rings on nozzle assemblies and fit into threaded wall openings holding the nozzle securely in place. Optimization Tips See page F2 for optimization tips. See lso ccessories line filters pressure regulators Pressure gauges Solenoid valves Liquid pressure regulators Strainers For J, request ata Sheets, and 1 For 1/2JJ, request ata Sheets and 1 For 2J, request ata Sheets and For thick wall adapters, request ata Sheets, 00 and 2 http:// ack onnect Steam Jacket Twin Thick Walls 1/2" NPT or SPT (F) inlet connection /" NPT or SPT (F) steam inlet/outlet connection 1/2" NPT or SPT (F) air and liquid inlet connection 1/2" NPT or SPT (F) inlet connection Please refer to data sheets 1/2J air atomizing nozzle 1/2J air atomizing nozzle used to spray seasoned cooking oil onto corn snacks. Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/2J Series s Features and enefits For wide angle round, round, circular and flat sprays, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. Wide angle round, round, flat and circular spray air caps produce wide angle round hollow cone spray, round hollow cone spray, flat spray and circular spray patterns. Performance ata 1 gasket must be ordered separately from the spray set-up, but is included in the standard nozzle assembly. Please contact your sales engineer. " (2 cm) 1" ( cm) 2" ( cm) cap Fluid cap 10 retainer ring 1 gasket tomizing Flat SU SU 20 2 2 2 Pattern Flat Flat Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1 2 2..1 1. 1..2.. 2 2. 2. 1.2.1 1. 2. 0 2. 1.0..1 1.0 1. 2 1 1. 10 2 2 2.1.0 2.. 1. 1. 2 2. 1 1.2. 1.. 2. 1.. 2 0 2.1 2 1.2 10. 2. 2. 2 1.. 1.1 1.. 2. 1.. 2.1.. 0..2 1. 2 2. 2. 0. 2 1...2..1 * 2 Liquid* 1 1 2 imensions 1 1 2 2 2 2 2 (ft.) 1 1 1 1 1 Phone 1-00--spray, FX 1---spray F

Pressure s, Internal Mix, 1/2J Series tomizing Performance ata Wide ngle Round and Round SU SU SU SU SU2 SU2 20 ---0 20 ---0 20 --- 0 2 --1-0 20 0 2 Pattern Wide ngle Round Wide ngle Round Wide ngle Round Wide ngle Round Round Round Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1 2 2. 2...2 1.. 2 1.. 2 1.0 2 2.2 1.2.0 2. 1.0 2.0 2.0 2. 1.1 0 1 2..0 1.0.2 2... 2..2..0...2. 2.2. 0 2..2 0.2...2 1. 1. 2 1.. 1. 1. 2..0.2. 2.2.2 2. 2.. 2..0..0 2.2 2 2. 2.. 0 2..0.0. 2. 2.. 1.... 2. 2.... 1.2 2 2.2. 2..0..1 1.0 1. 2 1 1. 10 2 2 2.1.0 2.. 1. 1. 2 2. 1 1.2. 1.. 2. 1.. 2 0 2.1 2 1.2 10. 2. 2. 2 1.. 1.1 1.. 2. 1.. 2.1.. 0..2 1. 2 2. 2. 0. 2 1...2..1 1.0.0. 2 1.. 1. 0 1... 2. 1.0...2 2... 1. 1. 0.. 2..1 1..2. 1. 2. 2.1.1. 1.0.2 2 2. 2.2.. 1. 1. 2.2.0..1 1.0 1. 2 1 1. 10 2 2 2.1.0 2.. 1. 1. 2 2. 1 1.2. 1.. 2. 1.. 2 0 2.1 2 1.2 10. 2. 2. 2 1.. 1.1 1.. 2. 1.. 2.1.. 0..2 1. 2 2. 2. 0. 2 1...2..1 * 0 0 2 0 2 Liquid* 2 1 2 1 2 1 2 1 2 1 2 imensions -1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2-1/2 1 1 1-1/2 1-1/2 1 1-1/2 1 1 1-1/2 1 1-1/2 1-1/2 1-1/2 2 2-1/2-1/2-1/2-1/2 2-1/2 2-1/2 2 2-1/2 2-1/2 2-1/2 2-1/2 2 2 2-1/2 2 2 2 2 2 1 (ft.) 2 2 2 2 2 2 1 2 2 2 1 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, 1/2J Series s Flat spray air caps produce a flat spray pattern. Features and enefits The dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. SUE and SU0 are pressure set-ups using pressurized liquids. In SU0, the air and liquid mix internally, while in SUE, they mix externally. SU0 is a siphon set-up with the air and siphoned liquid mixing externally. cap Fluid cap Flat spray pattern Performance ata " (2 cm) 1" ( cm) 2" ( cm) 10 retainer ring 1 gasket 10 retainer ring and 1 gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. tomizing Flat (External Mix) SUE 20 Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure 1 1 10 2 1. 0 10 1. 0 2 1. 0 10 2 0 0 2 1. 10 2 1. 2 10 1. 2 0 0 0 2 * 0 0 0 Liquid* 1 imensions -1/2-1/2-1/2 1-1/2-1/2 1-1/2 1 1-1/2-1/2 2 2 (ft.) 1 2 2 2 Phone 1-00--spray, FX 1---spray F

Pressure s, External Mix, 1/2J Series tomizing Performance ata ircular SU0 2 --1-1H Liquid apacity (gallons per hour)* and acity (standard cubic feet per minute)* Liquid Pressure.0..2 1.0. 2 2. 2.2 1.0.. 2. 1... 0 1 2. 2. 1.0 2. 1. 2 2...2 2. 2. 1.. 1. 1.0.. 2.2 2..... 2 2. 2.. 0... 2.. 2.. 2. 0.. 2...2.1. 2..2 1. 0. 2. 2 1.2..2. 0.. circular spray pattern Odor control at a compost facility using air atomizing nozzles. Phone 1-00--spray, FX 1---spray F

Siphon/Gravity-Fed s, External Mix, 1/2J Series s cap Fluid cap Round spray siphon air caps produce a round spray pattern. Round spray pattern " (2 cm) 1" ( cm) 2" ( cm) 10 retainer ring 10 retainer ring and 1 gasket must be ordered separately from the spray set-up, but are included in the standard nozzle assembly. Please contact your sales engineer. Refer to page F for Siphon/Gravity-Fed Liquid s diagram. 1 gasket Performance ata Round Siphon s SU0 20 tomizing apacity Gravity Head Liquid apacity (gallons per hour)* Siphon Height 1.0.. 1... 2... 2.2... 1.2. 0.. 0. 2..2 2..1 1. 2.1..... 0.1.2..0 1... 0 1.0..2...2 1. * 0 0 0 imensions at " Siphon Height -1/2-1/2-1/2-1/2-1/2-1/2-1/2 (ft.) 2 2 2 tomizing Phone 1-00--spray, FX 1---spray F

Nozzle odies/nozzle ssemblies, 1J Series tomizing 1J 1JN 1J Series air atomizing set-up 1 2 1. Retainer ring P 2. cap. Fluid cap. Nozzle body P Plug P10 Shut-off needle assembly 1J 1JN Features and enefits 1" NPT or SPT (F) 1" NPT or SPT (F) with shut-off needle Range in capacity from to 1 (1 to l/h). vailable with a shut-off needle. 1J features liquid and air feeds at opposite ends of the body and are provided with a removable plug so other needle assemblies may be added in the future. 1JN features a manual shut-off needle that enables the flow of liquid to be stopped. Optimization Tips See lso http:// See page F2 for optimization tips. s ccessories line filters pressure regulators Liquid pressure regulators Ordering Info Pressure gauges Solenoid valves Strainers Nozzle odies ode Nozzle Type Nickel-plated rass (none) l l Stainless Steel SS l l s Nickel-plated rass and Stainless Steel J JN SSR l l Stainless Steel SS l l omplete Nozzle ssembly Nozzle ody* *Includes retainer and gasket. 1 JN SS SU1 SS l l l l l Inlet onn. Nozzle ody ssembly Type ode ode SPT connections require the addition of a prior to the nozzle body inlet connection. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: 00-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: 1---0-SS. To order spray nozzle without set-up, use inlet connection, nozzle body and material code: 1JN-SS. Only SU1 l SS l ode To order spray set-up only, use spray set-up number and material code: SU1-SS. Phone 1-00--spray, FX 1---spray F0

Pressure s, Internal Mix, 1J Series s Wide angle round, round, and flat spray air caps produce hollow cone, wide angle round spray, round and flat spray patterns. Features and enefits For wide angle round, round and flat sprays, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed internally to produce a completely atomized spray. cap Fluid cap Performance ata " ( cm) " ( cm) " (2 cm) retainer ring must be ordered separately from the spray set-up, but is included in the standard nozzle assembly. Please contact your sales engineer. retainer ring tomizing Wide ngle Round SU1 00 1--- 0 Pattern Wide ngle Round Liquid apacity (gallons per minute)* and acity (standard cubic feet per minute)* Liquid Pressure gpm gpm gpm gpm gpm.0.2.1 2 2. 2...0 2. 1.1 2.. 0 2. 1.0 1. 1 2. 2.. 0. 2 2... 1. 1 2.0.1 0.2 1. 2 2 1. 2 2. 2. 2 0.1 2.2.1 1 2. 1 1. 2. 10.0 1 2. 1. 10 * 2 2 0 Liquid* imensions 1 1 1 1 1 1 1 2 1 (ft.) 1 2 2 2 1 Phone 1-00--spray, FX 1---spray F1

Pressure s, Internal Mix, 1J Series tomizing Performance ata Round and Flat SU SU12 SU1 00 1 200 2 00 11 Pattern Round Round Flat Liquid apacity (gallons per minute)* and acity (standard cubic feet per minute)* Liquid Pressure gpm gpm gpm gpm gpm.0.2.1 2 2. 2...0 2. 1.1 2.. 0 2. 1.0 1. 1 2. 2.. 0. 2 2... 1. 1 2.0.1 0.2 1. 2 2 1. 2 2. 2. 2 0.1 2.2.1 1 2. 1 1. 2. 10.0 1 2. 1. 10.0.2..0 2..2 1.1 1..0. 2.1 2. 2. 1. 1.0.. 0.. 0. 1.0 2. 1 2.2 1. 2. 2....2 1. 10 0..0.2.1 2 2. 2...0 2. 1.1 2.. 0 2. 1.0 1. 1 2. 2.. 0. 2 2... 1. 1 2.0.1 0.2 1. 2 2 1. 2 2. 2. 2 0.1 2.2.1 1 2. 1 1. 2. 10.0 1 2. 1. 10 * Liquid* 2 2 0 2 2 0 imensions 2 2 2 2 2 2 0 2 2 2 1 1 1 2 0 0 2 (ft.) 1 2 2 0 2 2 2 1 Phone 1-00--spray, FX 1---spray F2

Pressure and Siphon/Gravity-Fed s, External Mix, 1J Series s Flat spray and round spray air caps produce a flat spray pattern and the siphon air caps produce a round spray pattern. Features and enefits For flat spray, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a pressure-fed liquid system, the liquid is supplied to the nozzle under pressure. The liquid and compressed air or gas are mixed externally to produce a completely atomized spray. For round spray, dimensions, and are the pattern widths at distances from the nozzle. The total distance of spray projection from the nozzle to the maximum dispersal point is represented by. When using a siphon or gravity-fed liquid system, the liquid is supplied by either a liquid siphon or a gravity-feed. esigned to draw liquid through the feed line into the air flow where it is atomized. cap Fluid cap Performance ata Flat spray pattern " ( cm) " ( cm) " (2 cm) 1 retainer ring 1 retainer ring must be ordered separately from the spray set-up, but is included in the standard nozzle assembly. Please contact your sales engineer. tomizing Flat (External Mix) SUE1 20 Pattern Flat Liquid apacity (gallons per minute)* and acity (standard cubic feet per minute)* Liquid Pressure 1 gpm Siphon s Round SU10 200 2 gpm gpm gpm.0 2 1.0 1 2 1 0 2 1 2.0 1 1.0 1 0 2 1 2 11.0 1.0 1 0 1 2 11 0 2.0 1 0 1.0 1 11 0 2 0 2 2 0.0 1 1.0 11 0 0 2 2 0 2 2.0 11 0 1.0 0 2 0 2 2 tomizing apacity Refer to page F for Siphon/Gravity-Fed Liquid s. Gravity Head Liquid apacity (gallons per minute)* gpm Siphon Height 1 1. 1. 2 1.2.. 2.2... 2. 1. 1... 2. 1. 1.1...2 2. 2.2 1.. 0 2..0..0 2. 1..0 0..1..1 2. 1.. imensions Phone 1-00--spray, FX 1---spray F * 0 0 * 0 0 Liquid* 1 2 imensions at " Siphon Height 1 1 1 1 1 1 0 (ft.) 2 2 2 (ft.) 2

Fogger, Special Purpose tomizing 1/" NPT or SPT (F) threaded type QJ2 Split-eyelet type to clamp on 1/2", /", 1" pipe size Features and enefits produces high quality, cost-efficient dry fog. rops average fifteen microns in size and less. rop size is adjustable to meet specific industrial needs by changing the ratio of compressed air to water. Maintenance time is reduced because the built-in check valve, spray tip, and internal strainer are quickly serviced without tools. an use PV pipe and low-pressure air tubing. Tip has a relatively large clog-reducing orifice. QJ2 provides fast installation of the nozzle onto the liquid supply pipe no additional pipe fittings are required. Pipe cutting, threading and brazing are eliminated. Features a chemical-resistant, tight-fitting una-n seal to ensure leak-free performance. Ordering Info Specifications omplete Nozzle ssembly 1/ l l l Nozzle ody Inlet onn. Fluid Orifice ia. omplete Nozzle ssembly QJ2 / l l l Nozzle ody Pipe Size Fluid Orifice ia. SPT connections require the addition of a prior to the nozzle body inlet connection. Nozzle Inlet Jet Fogger Type 1/ To lamp On Pipe Size 1/2 Jet Fogger Type Fluid Orifice Orifice ia. Nom. 1.0.01.0 2.02 Fluid Orifice Orifice ia. Nom. 1.0.01 / QJ2.0 1 2.02 Humidification to reduce static charge in paint manufacturing plants. Phone 1-00--spray, FX 1---spray F

Fogger, Special Purpose Performance ata, QJ2 Water Pressure 0 0 0 0 0 Fluid Orifice 1 (.01" ia.) Pressure* 0 0 0 1.2 1.1 1. 2. 1. 1. 1.2 1. 2.. 2.0 1. 1. 1. 1. 2...2 2.1 1. 1. 1. 1. 1. 2..2.2.0 2. 2.1 1. 1. 1. 1. 0. 1. 2..2.1.0.. 2. 2. 2.2 1. 1. 1. 1. 1.0 1. 2..1.0.... 2. 2. 2. 2.2 2.0 1. 1. 1. 1. 2.2.1.0.... 2. 2. 2. 2. 2.2 2.0 1. 1. 1.2 2.1.1......1.0 2. 2. 2. 2. 2.2 2.2 1.2 2.1.0....., QJ2 Water Pressure 0 0 0 0 0 Fluid Orifice (.0" ia.) Pressure* 0 0 0.1 1. 1. 2.. 2.1 1. 1. 2....1 2.2 1.2 2.....1 2. 1.2 2.2.2.2...1 2.2 2.1.0..0....1 2.1 2.0 2.......2..1 2.2 1. 2..........1 2...........1 2...... tomizing, QJ2 Water Pressure 0 0 0 0 0 Fluid Orifice 2 (.02" ia.) Pressure* 0 0 0. 1. 1. 2... 2.1 1.1 2.1.2.. 2. 1. 2..... 2. 0. 1. 2.....1... 2. 1. 1. 2......2...0.0 1. 2...2.1.2...2...1.1 2..2.1.0..0.....0. 2.2.0..........0 2.1 2..... For applications with liquid pressures below psi (2 bar), request end cap sub-assembly 0--NY. In each line, figures in plain face indicate water atomized in (l/h) at psi (bar) water pressure. Figures in boldface indicate atomizing air in (Nl/min) at psi (bar) air pressure. Jet Fogger has a horizontal throwing distance of 1' (. m) and will expand to approximately ' (2. m) wide/' (. m) thick. 1. Values in blue area show optimum evaporation under normal room conditions, when center line of spray is ' (1. m) from the lower surface. 2. Values in red area can require up to ' ( m) for evaporation. Other values may be used where extended heat, higher air velocity exist or where slight surface wetting is permitted. Phone 1-00--spray, FX 1---spray F

ripsafe Special Purpose Fogger, tomizing Features and enefits High-volume/high-efficiency air atomization. Produces an adjustable, high-quality dry fog without wetting with pressure-fed liquid. Ideal for large/open structures and areas with high air exchange rates. Operation is through a drip safe air-actuated liquid shut-off valve. utomatically prevents liquid from spraying until air pressure at the nozzle is sufficient for fine atomization. rip safe valve simplifies system construction and control while improving performance. Operates using normal water pressures found in municipal water systems, eliminating the need for expensive, high-pressure hydraulic pumps. requirements are met using an air compressor with a capacity range that is suitable for the application. Requires minimal maintenance. The flat spray tip has a large orifice that reduces clogging. set-up and built-in strainer are quickly removed by hand if cleaning is required. tip is brass; valve and body polymer. Operates at pressures up to 0 psi ( bar) with a minimum air pressure range of 2 to psi (1. to 2. bar). split-eyelet or saddle clamp version of the Jet Fogger (2 Series) is also available for quick and easy mounting to the liquid supply pipe. 2 2 Optimization Tips See page F2 for optimization tips. pplications 1/" NPT or SPT (F) Split-eyelet type to clamp on pipe 1/2" to 1" Evaporative cooling Fogging Humidification Insecticide spraying Plant propagation Specifications Nozzle Inlet onn. Jet Fogger Type 1/ 2 Fluid Orifice Orifice ia. Nom. 1.0.01.0 2.02 See lso ccessories line filters pressure regulators Liquid pressure regulators Pressure gauges Solenoid valves Strainers For and QJ2, request ata Sheets and 2 For 2 and 2, request ata Sheets 2-1-2 and 2-1-2 http:// To lamp On Pipe Size 1/2 Jet Fogger Type Fluid Orifice Orifice ia. Nom. 1.0.01 / 2.0 1 2.02 Phone 1-00--spray, FX 1---spray F

ripsafe Special Purpose Fogger, Performance ata 2, 2 Water Pressure Fluid Orifice 1 (.01" ia.) Pressure* 0 0 0 1.2 1.1 1. 2. 1. 1. 1.2 1. 2.. 2.0 1. 1. 1. 1. 2...2 2, 2 Water Pressure Fluid Orifice (.0" ia.) Pressure* 0 0 0.1 1. 1. 2.. 2.1 1. 1. 2....1 2.2 1.2 2.. 2, 2 Water Pressure Fluid Orifice 2 (.02" ia.) Pressure* 0 0 0. 1. 1. 2... 2.1 1.1 2.1.2.. 2. 1. 2.. In each line, figures in plain face indicate water atomized in (l/h) at psi (bar) water pressure. Figures in boldface indicate atomizing air in (Nl/min) at psi (bar) air pressure. 1. Values in blue area show optimum evaporation under normal room conditions, when center line of spray is ' (1. m) from the lower surface. 2. Values in red area can require up to ' ( m) for evaporation. Other values may be used where extended heat, higher air velocity exist or where slight surface wetting is permitted.. Jet Fogger has a horizontal throwing distance of 1' (. m) and will expand to approximately ' (2. m) wide/' (. m) thick. tomizing Ordering Info omplete Nozzle ssembly 2 1/ 1 l l l Nozzle ody Inlet onn. Fluid Orifice ia. omplete Nozzle ssembly 2 1/2 1 l l l Nozzle ody Pipe Size Fluid Orifice ia. SPT connections require the addition of a prior to the nozzle body inlet connection. Phone 1-00--spray, FX 1---spray F

Humidification and Units tomizing Features and enefits ll equipment supplied for humidification systems except piping and wiring. 1/JH siphon air atomizing nozzles provide automatic, efficient humidity control with low installation and operating costs. operate either with compressed air drawing water from the float box by siphon action, or with water being delivered to the nozzle under pressure. Produces a fine atomized spray for rapid evaporation and efficient humidification. For information on siphon set-ups, see pages F2 to F. 1/JT pressure-fed air atomizing nozzles provide automatic, efficient humidity control with low installation and operating costs. Suitable for use in systems where water is under pressure. Have built-in strainers for air and water plus a ball check valve in the water line. Produces a fine atomized spray for rapid evaporation and efficient humidification. For information on pressure set-ups, see pages F to F. 0 humidification unit is a self-contained humidifier suitable for use with deionized water (I). Easy to install on a wall or for use in non-ducted applications. regulator and gauge, V air control solenoid and air line filter are included within the Humidification Unit. Wall-mounting bracket is also provided.. lbs. (. kg). For each spray set-up, water capacity ranges from 2. lbs./hr at psi (0. bar) air to. lbs./hr at psi ( bar) air. YMF MiniFogger III is ideal for humidification applications with limited space due to its compact design. vailable with a choice of one to four stainless steel spray nozzle set-ups with a wide variety of flow-rate sizes/droplet sizes and types. For each spray set-up, water capacity is 0.2 to 1.1 (1.0 to. l/h), and air capacity is to nl/min at. psi (.0 bar). an be placed in hard-to-reach spaces and can be easily installed on a header, on a wall or on a ceiling. 0. lbs. (2 g) for single spray set-up type; 0. lbs. (20 g) for multiple four set-up types. Height is." ( mm). The body, retainer cap, and tank are made of corrosionresistant polypropylene with stainless steel air and water connections. s are also compatible with deionized water. -00 provides a finely atomized spray without the use of compressed air. Produces a hollow cone spray pattern. Requires a minimum liquid pressure of psi (1 bar) to the nozzle. Maximum operating pressure of 00 psi ( bar). 1/JH 0 YMF -00 Siphon inlet connection 1/" NPT and SPT inlets 1/JT 1/" NPT or SPT (F) MiniFogger III 1/" NPT or SPT (F) air and liquid inlet connection 1/" NPT or SPT (F) misting nozzle Pressure-fed inlet connection 1/" NPT and SPT inlets Phone 1-00--spray, FX 1---spray F

Humidification and Units Optimization Tips s See page F2 for optimization tips. See lso ccessories line filters pressure regulators Performance ata YMF MiniFogger III 0 psi Orifice iameter tomizing apacity Water apacity..2..2..2.2.2 0 1..1 1.. ata per Nozzle ( Pressure 0. MPa) Liquid apacity apacity Mean roplet Size (micron)* Pressure psi istance (ft.) SU2.N 0.02. 1.2.. *Sauter Mean iameter 0.1 MPa = 1 bar Pressure gauges Solenoid valves Liquid pressure regulators Strainers For 1/JH siphon air atomizing nozzles, request ata Sheet 1 For 1/JT pressure-fed air atomizing nozzles, request ata Sheet For 0 humidification unit, request ata Sheet 0 For YMF MiniFogger III, request ata Sheet YMF -00 Liquid apacity 00. 0 1.0 00 1.1 00 1.2 00 1.2 00 1. Float box with float valve TW liquid strainer atomizing nozzle pipe assembly E Pipe hanger F filter G Pressure regulator with gauge H Solenoid valve I Switching relay J Humidistat http:// Nozzle odies ode Nozzle Type JH JT 0 YMF rass (none) l Nickel-plated rass (none) l l Kynar KY l Stainless Steel SS l l /s Nickel-plated rass SSR l l Nickel-plated rass and Stainless Steel SSR l l Kynar KY l Stainless Steel SS l l l PTFE TEF l Ordering Info omplete Nozzle ssembly Nozzle ody* 1/ JH SS SU1 SS l l l l l Inlet onn. Nozzle ody ode *Includes retainer and gasket. ode SPT connections require the addition of a prior to the nozzle body inlet connection. To order spray set-up only, use spray set-up number and material code: SU1-SS. To order fluid cap only, use fluid cap number (shown in performance data charts) and material code: 1-SS. To order air cap only, use air cap number (shown in performance data charts) and material code: -SS. To order spray nozzle without set-up, use inlet connection, nozzle body and material code: 1/JH-SS. Humidification Unit YMF- l l Humidification Unit Type of s Humidification Unit 0 1 l l Humidification Unit Type Typical humidifying set-ups for siphon nozzles G F I H E J of s tomizing Phone 1-00--spray, FX 1---spray F

Humidification System omponents tomizing Features and enefits 2-SE pipe assembly consists of straight and formed tubing with fittings, globe valve and split-eyelet connectors. Not assembled. - humidistat will respond to humidity levels in the range of % to % RH. Maximum operating temperature F (2 ). V ; 1V. Overall height " (1 cm). - switching relay has built-in transformer that supplies low-voltage current for humidistat circuit. 2-wire V control, V. Maximum temperature F ( ). 0 electric humidistat quick relative humidity L readouts from 1% to % with repeatability of ±%. Operating temperature range 2 F to 1 F (0 to 1 ). V ( or ). float valve used in 0 float box to shut off inlet flow at a preset water level. Made of S plastic, Stainless Steel, polypropylene with fiber washers and a brass nut. Optimization Tips See page F2 for optimization tips. 0 valve package is easy to install and use simply connect to existing air and fluid lines. The NEM type panel is completely sealed to eliminate moisture damage to components. Safety feature ensures there is no product damage due to unintentional water release. Stainless steel components available for use with deionized water. Separate atomizing and cylinder air lines with adjustable delay time assures liquid atomization. pipe hanger for proper spacing between air and liquid lines. Sizes fit 1/2" piping. Hanger is held by threaded rod and nuts (not included) for vertical adjustment. Made of cast aluminum. " ( cm) spacing. Use with 2-SE spray pipe assembly. See lso ccessories line filters pressure regulators Liquid pressure regulators Section L, ccessories Pressure gauges Solenoid valves Strainers For 2-SE pipe assembly, request ata Sheet 2-SE For 0 electrical humidistat, request ata Sheet 0 http:// 2-SE - - 0 pipe assembly Humidistat Switching relay Electric humidistat 0 0 Float valve Float box Valve package Pipe hanger Phone 1-00--spray, FX 1---spray F

tomizing ccessories Features and enefits 1 pressure tank assembly meets SME oiler and Pressure Vessel ode requirements and OSH safety regulations. onstructed of Stainless Steel. ssembly includes a pressure regulator with gauge, SME coded pressure relief valve, air bleed valve and plug valves for air inlet and liquid outlet. Tanks are available in 1, 2, and gallon (.,., 1. and liter) capacities. The air inlet and liquid outlet have 1/" NPT (F) connections. The maximum working pressure is 1 psi at 0 F (. bar at ). The 1 features brass fittings and an EPR lid seal. 10 split-eyelet swivel union simplifies installation and maintenance of air atomizing nozzles and spray guns. onnector design reduces costs by eliminating cutting, threading, welding and brazing operations and adjustment of fittings, unions and nipples. Recommended pressure is up to 20 psi (1 bar) for liquid and air lines. Fits 1/2", /" or 1" pipe or similar O.. tube. 1/" NPT or SPT (M) outlet pipe connections. Nickel-plated brass with zinc-plated pipe clamps or all stainless steel construction. 2, 2 level switch kit indicates a low liquid level condition inside the pressure tank. Use standard 2 level switch with and gallon (1 and liter) pressure tank assemblies with external 1/" NPT (F) threads. Use 2 level switch with 1 and 2 gallon ( and liter) pressure tank assemblies with external 1/" NPT (F) threads. Features a U.L. listed float switch, quick disconnect and ' ( m) PV jacketed cable. vailable in brass with una-n float or all stainless steel. tank heater bands provide anywhere from F to F ( to ) heat gain depending upon the tank size and number of bands used. Silicone rubber construction with fiberglass mesh reinforcement for added strength, flexibility, and corrosion resistance. Features quick-release band clasp and built-in thermostat for temperature control. Two sizes fit " and " (2. and. mm) diameter tanks. push-in tube fittings provide fast and easy hook-up of air atomizing nozzles. urable nickel-plated brass construction includes una-n O-ring. Select from six configurations with 1/", 1/" or /" NPT (M) connections for 1/", /" and 1/2" O.. tubing. 2 ferrule-type tube fittings are intended for use when operating at higher pressures. The 1 Stainless Steel is of durable construction and can be easily taken apart for cleaning. Six configurations available with 1/", 1/" or /" NPT connections for 1/", /" and 1/2" O.. tubing. 1 and 2 strong, semi-rigid nylon tubes designed for use with fittings. brasion resistant and dimensionally stable tubing available in ', 2' and 0' (. m,. m and 1 m) lengths. Maximum working pressure is 20 psi (1 bar) at F to 0 F ( to ). 1 has 1/" O.. 2 has /" O.. tomizing Phone 1-00--spray, FX 1---spray F1

tomizing ccessories tomizing 1 10 Pressure tank assembly Split-eyelet swivel union Optimization Tips 2 and 2 and 2 Level switch kit Tube fittings Tank heater bands See lso http:// See page F2 for optimization tips. For 1 pressure tank assembly, request ata Sheet 1 For 10 split-eyelet swivel union, request ata Sheet 10 For 2, 2 level switch kit, request ata Sheet 2 and 2 For tank heater bands, request ata Sheet For, request ata Sheet For 2 ferrule-type tube fittings, request ata Sheet 2 For 1 and 2, request ata Sheets 1 and 2 Phone 1-00--spray, FX 1---spray F2