Preparation Part Number: 08586-OC890 Conflicts Do not install into vehicles with Factory Alarm Systems or without Immobilizer. Do not use Techstream Lite for Registration. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio *Mandatory Kit Contents Item # Quantity Description 1 1 GBS ECU w/bracket attached Hardware Bag Contents Item # Quantity Description 1 1 M6 Flange Nut 2 1 GBS Microphone 3 2 V2 Window Label w/ red tag (discard) 4 2 V2 Window Label w/ red tag SPANISH (discard) 5 2 V5 Window Label 6 2 V5 Window Label SPANISH 7 1 V2 Owner s Guide (discard) 8 1 V5 Owner s Guide 9 1 Warranty Card Additional Items Required For Installation Item # Quantity Description NOTE: Part number of this accessory may not be the same as the part number shown. Recommended Tools Personal & Vehicle Protection Safety Glasses Safety Gloves Vehicle Protection Special Tools Notes (Optional) Blankets, Parts Boxes Notes Striker Tool (PPO only) CAD-E IADS P/N ALL 02-016-01 Scan Tool and Software Card 01001271 with Version 13.4 Software (or later) Techstream Notebook Do not use Techstream Lite Installation Tools Notes Phillips Head Screwdriver #2, screwdriver or tip Flat Blade Screwdriver 1/8 wide screwdriver Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST # 00002-06001-01 Torque Wrench Battery - 36 in bf (4.7 N m) Airbag - 88.5 in bf (10 N m) Clear Tape Socket Special Chemicals Cleaner Glass Cleaner Legend 10mm, Extension Notes VDC approved cleaner Household Glass cleaner Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). Safety (eye protection, rechecking torque procedure, etc.). Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety. Issue: B 07/28/11 Page 1 of 22 pages
A B GBS ECU GBS Microphone TOYOTA TUNDRA 2007 - TVIP V5 Preparation
1. Vehicle Disassembly (a) Vehicles with Automatic Transmission should be placed in Park and have the Parking Brake set before disconnecting the Battery. Fig. 1-1 10mm Socket Negative Battery Cable (b) Remove the Negative Battery Cable. (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable Position, as it will be reinstalled in the same position. DO NOT TOUCH THE POSITIVE BATTERY TERMINAL. Nylon Panel Removal Tool Step Cover (c) Remove the Driver s Step Cover. (Fig. 1-2) (1) Begin by protecting the Vehicle Interior with Blankets. Fig. 1-2 Cowl Cover (d) Remove the Driver s Cowl Cover. (Fig. 1-3) (1) Remove 1 Cowl Nut. Cowl Nut Fig. 1-3 Page 3 of 22 pages
Nylon Panel Removal Tool, 10mm Socket (e) Dislodge the Lower Dash Cover. (Fig. 1-4) (1) Remove 2 Bolts. (2) Disconnect any Connectors. Hood Release Lever Bolt Fig. 1-4 Bolt Lower Dash Cover Hood Release Lever Retaining Clip (f) Dislodge the Hood Release Lever from the Lower Dash Cover. (Fig. 1-5) (1) Press down on the Retaining Clip while pushing the Lever out. Fig. 1-5 Hood Latch Cable Hood Release Lever (g) Remove the Hood Latch Cable from the Hood Latch Lever. (Fig. 1-6) (h) Remove the Lower Dash Cover. Fig. 1-6 10mm Socket (i) Dislodge Driver s Side Knee Airbag. (Fig. 1-7) (1) Remove 4 bolts. CAUTION: SHARP METAL EDGES. Fig. 1-7 Bolts (x4) Page 4 of 22 pages
(j) Wrap the Airbag in a blanket and place on a box to avoid tension on the harness. (Fig. 1-8) Knee Airbag CAUTION: SHARP METAL EDGES. TVIP Box Fig. 1-8 FOR VEHICLES WITH COLUMN MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps k-n) (k) Remove Vehicle Drink Holder. (Fig. 1-9) (1) Press in the tabs on each side and pull outward on the Cup Holder. Fig. 1-9 Phillips Screwdriver (l) Remove the 2 bottom Screws from the Cup Holder Drawer Assembly. (Fig. 1-10) Screws (x2) Fig. 1-10 CONTINUED Page 5 of 22 pages
Phillips Screwdriver Screws (x2) (m)remove the 2 top Screws. (Fig. 1-11) Fig. 1-11 Nylon Panel Removal Tool (n) Remove the Cup Holder Drawer Assembly. (Fig. 1-12) Fig. 1-12 Nylon Panel Removal Tool FOR VEHICLES WITH FLOOR MOUNT AUTOMATIC SHIFT LEVERS ONLY. (Steps o) (o) Remove the small Tray below the Climate Control Console. (Fig. 1-13) (1) Disconnect any Connectors. Fig. 1-13 Tray (p) Remove the Knockout Cover from the Climate Control Console. (Fig. 1-14) (1) Disconnect the 4P Connecter from the Knockout Cover. (2) Discard the Knockout Cover. Fig. 1-14 Knockout Cover Page 6 of 22 pages
2. GBS Microphone Installation (a) Feed the 4P Connector through the Climate Control Console and connect it to the GBS Microphone. (Fig. 2-1) (1) Verify that the Connector is secure. GBS Microphone 4P Connector Fig. 2-1 (b) Insert the GBS Microphone into the Climate Control Console. (Fig. 2-2) GBS Microphone Fig. 2-2 Flat Blade Screwdriver GBS ECU 3. GBS ECU Preparation (a) Verify that the GBS ECU s sensitivity is set to 5. (Fig. 3-1) Fig. 3-1 Page 7 of 22 pages
Fig. 4-1 10mm Socket, Extension Remove Nuts (x2) Vehicle Brace Vehicle J/B 4. ECU installation (a) Remove 2 Nuts from the Vehicle Brace near the Drivers Side J/B. (Fig. 4-1) (b) Pull the Brace away from the Vehicle Reinforcement. (Fig. 4-1) (1) Do not remove the Brace from the studs. (c) Install Bracket and GBS ECU. (Fig. 4-2) (1) Make sure that the Bracket Pin seats properly. Bracket Pin GBS ECU Fig. 4-2 10mm Socket, Extension Reinstall Reinstall Fig. 4-3 M6 Flange Nut GBS ECU (d) Use the M6 Flange Nut from the supplied kit to secure the ECU Bracket in place. (Fig. 4-3) (e) Re-secure the Vehicle Brace by reinstalling 2 Nuts. (Fig. 4-3) (1) Verify that the Bracket is secure. 8P Connector (f) Locate the Vehicle s White 8P Connector near the Driver s Side J/B Area. (Fig. 4-4) (1) Remove the Tape securing the Connector. Fig. 4-4 Page 8 of 22 pages
(g) Connect the Vehicle Harness's White 8P Connector to the GBS ECU. (Fig. 4-5) 8P Connector (1) Verify that Connector is securely connected. Fig. 4-5 GBS ECU 5. Registration Preparation Torque Wrench (a) Complete the reassembly of the vehicle. (1) Reconnect any disconnected connectors. (2) Verify the panels fit together properly with no uneven gaps between them. (b) When installing the Driver s side Knee Airbag, install the bolts in the specified order. (Fig. 5-1) Fig. 5-1 (1) Tighten the bolts to 88.5 in lbf (10 N m) (c) Install the Short Pin (Fig. 5-2) Install Short Pin Fig. 5-2 Negative Battery Cable (d) Temporarily reconnect the Negative Battery Terminal. (Fig. 5-3) DO NOT TOUCH THE POSITIVE BATTERY TERMINAL. Fig. 5-3 Page 9 of 22 pages
Vehicle Diagnostic Port 6. Registration w/techstream Notebook. Techstream Notebook CAUTION: Techstream Lite will not work for this section, use the Techstream Notebook ONLY. (a) Connect the Techstream Notebook to the Vehicles Diagnostic Port. (Fig. 6-1) Fig. 6-1 (b) Start the TIS Techstream Application by clicking on the shortcut located on the Desktop. (c) Use the Vehicle Key to turn the Vehicles Ignition Switch to ON. (d) Click Connect to Vehicle. (Fig. 6-2) Fig. 6-2 (e) Confirm that the information displayed on the Vehicle Connection Wizard is correct for the vehicle. If not verify that the Techstream is properly connected. (Fig. 6-3) (f) Click Next>. (Fig. 6-3) Fig. 6-3 Page 10 of 22 pages
(g) Click Customize Setting. (Fig. 6-4) Fig. 6-4 (h) Make sure that the Customize tab is selected. (Fig. 6-5) (i) Select Option Setup. (Fig. 6-5) (j) Click (Fig. 6-5) Fig. 6-5 (k) Select ON. (Fig. 6-6) (l) Click (Fig 6-6) Fig. 6-6 Page 11 of 22 pages
(m)click Next to accept the changes to the Vehicle. (Fig. 6-7) Fig. 6-7 (n) Click (Fig. 6-8) Fig. 6-8 (o) Click Close. (Fig. 6-9) Fig. 6-9 Page 12 of 22 pages
(p) Click (Fig. 6-10) Fig. 6-10 7. Registration w/ Scan Tool. Scan Tool, Software Card Diagnostic Connector Ensure the Scan Tool Software is version 13.4 or later). If not, download the latest version from Toyota Information Systems (TIS) (a) Connect the scan tool connector to the vehicle s diagnostic connector in the right side of the lower dash area. (Fig. 7-1) Fig. 7-1 Scan Tool (b) Use the key to turn the ignition to the ON position. (c) Verify the shift lever position is in "N" or "P. (d) Push the scan tool main switch to "ON," then press "ENTER." (Fig. 7-2) Fig. 7-2 Page 13 of 22 pages
(e) Select "CUSTOMIZE" in the Application Select menu with the scroll key, then press "ENTER." (Fig. 7-3) Fig. 7-3 (f) Select "NEW VEHICLE" with the scroll key, and press "ENTER." (Fig. 7-4) Fig. 7-4 (g) Select "2007" with the scroll key, and press "ENTER." (Fig. 7-5) Fig. 7-5 (h) Select "TUNDRA" with the scroll key, then press "ENTER." (Fig. 7-6) Fig. 7-6 Page 14 of 22 pages
(i) Select "NORTH AMERICA" with the scroll key, then press "ENTER." (Fig. 7-7) Fig. 7-7 (j) Select the Slide Roof Option that is Equipped on the Vehicle with the scroll key, then press "ENTER." (Fig. 7-8) Fig. 7-8 (k) Verify the Information, and press "YES." (Fig. 7-9) Fig. 7-9 (l) Verify the connection of the DLC3 Cable. Press "YES" to continue. (Fig. 7-10) Fig. 7-10 Page 15 of 22 pages
(m)in the "Customize" menu, select "OPTION SETUP" then press "ENTER." (Fig. 7-11) Fig. 7-11 (n) Select "01: DOP SECURITY," then press "ENTER." (Fig. 7-12) Fig. 7-12 (o) Select "ON" in the "OPTION SETUP" menu with the scroll key, then press "ENTER." (Fig. 7-13) Fig. 7-13 (p) Press "YES." (Fig. 7-14) Fig. 7-14 Page 16 of 22 pages
(q) Press "ENTER." (Fig. 7-15) Fig. 7-15 Page 17 of 22 pages
8. Warning Label Installation. For US Vehicles use the English Labels and Dispose of the Spanish Labels. For Mexico Vehicles use the Spanish Labels and Dispose of the English Labels. Clear Tape (a) Use Household Glass Cleaner to clean the inside of the Front Door Window. (Fig. 8-1) Molding Etching Etching (b) Use a piece of Clear Tape to lift the Label from the protective backing. CAUTION: Do not touch the adhesive surface. (c) Attach the V5 Window Label. (Fig. 8-1) Fig. 8-1 Molding NOTE: Make sure to Align according to Etching or Other Label. (Fig. 8-1) REPEAT: steps a c with the other Window. 9. Complete the Installation Fig. 9-1 Torque Wrench, 10mm Socket Negative Battery Cable (a) Position the Negative Battery Cable at the original factory position. (Fig. 9-1) (1) Tighten the Nut to 36 in lbf (4.7 N m) DO NOT TOUCH THE POSITIVE BATTERY TERMINAL. (b) Clean up and remove any trash. (c) Place the Owner's Guide and Warranty Card, sealed in the bag, in the Glove Box. (d) Discard the GBS Owners Guide. Page 18 of 22 pages
TOYOTA TUNDRA 2007 TVIP V5 CHECKLIST these points MUST be checked to ensure a quality installation. Accessory Function Checks Perform 1 Press and release the remote control s lock button to start the system s arming process. Look For All doors lock. The security LED lights up. 2 Wait 30 seconds. 3 Press and release the remote control s unlock button to disarm the system. The driver s door unlocks. Open the driver s door, insert the key into the ignition switch and turn it to ON. Roll down all the windows, remove the key and exit the vehicle. 4 The doors automatically relock. The system automatically starts the arming process. 5 Press and release the remote control s unlock button again to stop the arming process. 6 Insert the key into the driver s door key vehicle to start the arming process. Refer to step 3 All doors lock. The Security LED lights up. 7 Wait 30 seconds. 8 Reach inside and manually unlock the driver s door to trigger an alarm. The driver s door automatically relocks. The horn sounds repeatedly. The Security LED lights up. 9 Manually unlock the driver s door again and hold it unlocked, open the door, then sit in the driver s seat. The driver s door lock attempts to lock repeatedly. The horn continues to sound repeatedly. The Security LED remains on. 10 turn it to START to stop the alarm. The horn stops sounding. The Security LED turns off. The starter cranks and the engine starts. Turn the key back to LOCK, remove it, and then exit the vehicle. 11 on the door to lock the doors, then close the door to start the system s arming process. All doors lock. The Security LED lights up. 12 Wait 30 seconds. Issue: B 07/28/11 Page 19 of 22 pages
TOYOTA TUNDRA 2007 TVIP V5 CHECKLIST these points MUST be checked to ensure a quality installation. 13 Reach inside and manually unlock the front passenger s door to trigger an alarm. The front passenger s door automatically relocks. The horn sounds repeatedly. The Security LED lights up. 14 Press and release the remote control s unlock button to stop the alarm. The horn stops sounding. 15 Press and release the remote control s lock button to start the system s arming process, Refer to steps 1 and 2. armed. 16 Unlock and open one of the rear passenger doors to trigger an alarm. (if available) 17 Press and release the remote control s unlock button to stop the alarm. Refer to step 13. Refer to Step 14 18 passenger door. (if available) Refer to steps 1, 2, and 13. Roll up all windows, remove the key and exit the vehicle. 19 Press and release the remote control s lock button to start the arming process. Refer to step 1. 20 Wait 30 seconds. Perform the following check in a temperature-controlled environment. (50-90 F) 21 With the tip of a key, or Striker Tool pulled The horn sounds repeatedly. alarm. 22 Insert the key into the driver s door key The Security LED lights up. Refer to Step 10 vehicle to stop the alarm. NOTE: If the alarm still does not trigger during the section test, increase the GBS sensitivity to the next setting and test again. NOTE: Issue: B 07/28/11 Page 20 of 22 pages
TOYOTA TUNDRA 2007 TVIP V5 CHECKLIST these points MUST be checked to ensure a quality installation. Vehicle Function Checks Function Function Enter the Vehicle Without Interference Horn Hood Latch Release Start the Vehicle Starter Gauges ABS Light (if equipped) If the warning light remains on, it may indicate a system malfunction. Lamp Failure Sensor If the warning light remains on, it may indicate a system malfunction. Seat Belt Warning Light If the warning light remains on, it may indicate a system malfunction. Air Bag Warning Light If the warning light remains on, it may indicate a system malfunction. If the warning light remains on, it may indicate a system malfunction. Tire Pressure Monitoring System (TPMS) (if equipped) Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on. After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on. Using a Mirror or Assistant check the following. Tail Lights Brake Lights Backup Lights Daytime Running Lights (if equipped) Marker Lights Stop the Engine, Place the Vehicle s IG in the ON position. Hazard Lights Head Light Turn Signal Lights Fog Lights (if equipped) High Beams Rear Sunshade (if equipped) Issue: B 07/28/11 Page 21 of 22 pages
TOYOTA TUNDRA 2007 TVIP V5 CHECKLIST these points MUST be checked to ensure a quality installation. Function Function (if equipped) Navigation System (if equipped) Front Windshield Defogger (if equipped) Side Mirror Defogger (if equipped) Massage Seats (if equipped) Glovebox Light (if equipped) Key Sensor Buzzer Remove the short pin after Function check. Store Short Pin Here Issue: B 07/28/11 Page 22 of 22 pages