(Replaces HNI-211-HNI-225) FEBRUARY 2008 - NEW ITEM BULLETIN NIB-208 20970 Bumper and Door Insulator Nylon Screw 22mm Head O.D. Stem Diameter: 14mm Stem Length: 34mm No. 3 Square Drive Fits Into 12mm Hole GM, Ford & Chrysler 2595 Is Now Available! We have tooled and are now man u fac tur ing another popular Tubular Nut 2595 Phosphate 1/8 Stud Size.040 -.045 Fits Into 3/16 Hole 0 20985 (07129-925-734) Zinc U Type Nut M4.8 (#10) Screw Size 2.5mm-3.75mm Center of Hole to Edge: 8mm BMW 3, 7, 8 & Z3 1991 On UNIT PACKAGE: 50 20956 (90467-05114) Bumper & Fender Apron Nylon U Nut Screw Size: M5.5 (#12) Width: 20mm, Length: 36mm Center Of Hole to Edge: 14mm Up To 1mm Lexus & Toyota 2000 On 21001 (N621945-S2) Phosphate Free Spinning Washer Nut M12-1.75 Thread 18mm Hex Washer O.D.: 28mm Ford Bumper Bolts & General Purpose Sealed Crimp & Solder Butt Connectors The Ultimate Electrical Connection! Sealed Crimp & Solder Butt Connectors are crimped for mechanical reliability, soldered for superior strength and conductivity, and sealed with heat shrink tubing for maximum durability. The Components: THE CRIMP CONNECTOR * There are crimp indicators which show where the installation tool should be positioned * Wire-stop in the connector prevents over-insertion of the wire * Window in the connector allows for visual inspection & solder to flow into THE SOLDER * Flux coating to clean metal surfaces * Pre-measured solder to provide the right amount of solder to ensure a solid termination * Low-temperature solder alloy for ease of installation THE HEAT SHRINK TUBING * Adhesive lined polyolefin to seal the connection * Color coded with wire gauge imprint for easy size identification * Translucent tubing to allow for visual inspection 21002 Clear 24-22 Ga. 21003 Red 20 18 Ga. 21004 Blue 16 14 Ga. 21005 Yellow 12 10 Ga. UNIT PKG: 10 UNIT PKG: 10 UNIT PKG: 10 UNIT PKG: 10 Copy right 2008, Au-ve-co Prod ucts Co. "SINCE 1916" THE COM PLETE FAS TENER LINE 33
NIB-0208 FEBRUARY 2008 - NEW ITEM BULLETIN (Replaces HNI-211-HNI-225) Not Actual Size Not Actual Size 20486 Red Primary Wire 18 Gauge Length: 45 Ft. Stranding: 16 x 30 O.D.:.092 UNIT PACKAGE: 1 Roll 21006 (15306157) White Shell, Natural Insert Daytime Running Lights & Turn Signal Harness Connector Bulb Nos. 3156 & 4156 Two 8 long 20 gauge wire leads GM Cars & Light Duty Trucks 1999 On UNIT PACKAGE: 1 PREMIUM IMPORTED MINIATURE BULB 20969 4114K Bulb (Krypton, Clear, Long Life) Not Actual Size Ergo Tuflok Assortments Now these GM, Ford and Chrysler s with their wide range of hole diameters and panel thicknesses are available in three different types of popular Auveco assortments. Quik-Select Assortment Translucent Durable Polypropylene Box With Locking Tabs 6-3/4 x 11 x 1-3/4 No. 6870 GM, Ford & Chrysler s 11 Varieties 116 Pieces Contains the following Auveco part numbers: 20826, 20880, 20888, 20889, 20988, 20989, 20990, 20991, 20992, 20993 & 20994 Quik-Select II Assortment Translucent Durable Polypropylene Box With Locking Tabs 8-13/16 x 13-1/16 x 2-1/4 No. 6919 GM, Ford & Chrysler s 11 Varieties 215 Pieces Contains the following Auveco part numbers: 20826, 20880, 20888, 20889, 20988, 20989, 20990, 20991, 20992, 20993, & 20994 6500 Series Large Drawer Fix-Kit Heavy gauge steel with plastic insert. Each compartment will hold the entire contents of one standard Auveco unit package. 12 x 18 x 3 No. 6542 GM, Ford & Chrysler Push-Type Retainers 11 Varieties 325 Pieces Contains the following Auveco part numbers: 20826, 20880, 20888, 20889, 20988, 20989, 20990, 20991, 20992, 20993 & 20994 34 THE COM PLETE FAS TENER LINE "SINCE 1916" Copy right 2008, Au-ve-co Prod ucts Co.
(Replaces HNI-211-HNI-225) FEBRUARY 2008 - NEW ITEM BULLETIN NIB-208 20987 Specialty Rivet 3/32 Diameter Shoulder Diameter: 1/8 Grip: Up To 3/32 Flange Diameter: 3/16 Aluminum Rivet Aluminum Mandrel Replaces welded on studs for attaching stud style moulding clips 20971 (003-990-94-97) Split-Type Rivet 5/32 (4mm) Diameter Grip: 3/64 9/32 (1mm 7mm) Flange Diameter: 5/16 (8mm) Aluminum Rivet Aluminum Mandrel Mercedes-Benz 20983 (GJ6R-68-ABX) Trim Panel Retainer Top Head Diameter: 13mm Middle Head Diameter: 16mm Bottom Stem Diameter: 9mm Mazda 3, 5, 6, Miata & RX-8 20959 (91560-S9A-A01) Top Head Diameter: 13mm Middle Head Diameter: 16mm Bottom Head Diameter: 15mm Stem Diameter: 9.5mm Acura TL & TSX and Honda Accord, Civic, CRV & Odyssey 20995 (11562043) Pin Top Hd. Dia: 19mm Pin Bottom Hd. Dia: 19.5mm Pin Stem Length: 22mm Grommet Flange Dia: 24mm Grommet Stem Length: 12mm Cadillac SRX & STS, Chevrolet Cobalt & HHR and Hummer H3 20996 (11562044) Yellow Nylon Pin Top Hd. Dia: 19mm Pin Bottom Hd. Dia: 19.5mm Pin Stem Length: 22mm Grommet Flange Dia: 24mm Grommet Stem Length: 12mm Cadillac SRX & STS, Chevrolet Cobalt & HHR and Hummer H3 20997 (11562288) Yellow Nylon Pin & Grommet Pin Top Hd. Dia: 19mm Pin Bottom Hd. Dia: 19.5mm Pin Stem Length: 22mm Grommet Flange Dia: 24mm Grommet Stem Length: 12mm Hummer H2 20998 (11562256) Black Nylon Pin & White Nylon Grommet Pin Top Hd. Dia: 19mm Pin Bottom Hd. Dia: 19.5mm Pin Stem Length: 22mm Grommet Flange Dia: 24mm Grommet Stem Length: 12mm Chevrolet Cobalt, HHR & Full-Size Van 20999 (11562257) Green Nylon Pin & Yellow Nylon Grommet Pin Top Hd. Dia: 19mm Pin Bottom Hd. Dia: 19.5mm Pin Stem Length: 22mm Grommet Flange Dia: 24mm Grommet Stem Length: 12mm Chevrolet Cobalt & HHR Copy right 2008, Au-ve-co Prod ucts Co. "SINCE 1916" THE COM PLETE FAS TENER LINE 35
NIB-0208 FEBRUARY 2008 - NEW ITEM BULLETIN (Replaces HNI-211-HNI-225) 20944 (11588863) Green Nylon Door Trim Panel Retainer Top Bottom Head Diameter: 25mm Stem Diameter: 8mm Stem Length: 24mm Buick Terraza, Chevrolet Uplander, Pontiac Montana & Saturn Relay 20949 (W711037-S300) Black & Door Trim Panel Retainer Top Head Diameter: 13mm Middle Bottom Head Diameter: 16mm Stem Diameter: 8mm Stem Length: 12mm Ford Edge, Escape, Freestyle Mariner, Montego & 500 20946 (W711017-S300) Door Trim Panel Retainer Top Head Diameter: 14mm Middle Head Diameter: 14mm Bottom Stem Diameter: 9.5mm Stem Length: 16mm Ford Fusion 21023 (6503336) Cowl Screen Retainer Stud: 1/4-20 x 7/16 Flange Diameter: 9/16 Stem Diameter: 19/64 Stem Length: 13/32 Overall Length: 31/32 Use With Auveco 18249 & 19792 Dodge Ram 1994 On 20947 (11561382, 11610198) Headlight Grommet 13mm x 20mm Overall Length: 19mm Pontiac G6 20973 (10352798) Tan Nylon Rocker Panel 11/16 x 1-5/16 Stem Length: 11/16 Fits Into 5/16 Hole Chevrolet Impala, Lumina & Monte Carlo 2000 - On 20974 (10352804) Maroon Nylon Rocker Panel 15/32 x 1-9/32 Stem Length: 11/16 Fits Into 5/16 Hole Chevrolet Impala, Lumina & Monte Carlo 2000 - On 20975 (10353834) Red Nylon Rocker Panel 15/32 x 1-9/32 Stem Length: 11/16 Fits Into 5/16 Hole Chevrolet Impala, Lumina & Monte Carlo 2000 - On 20976 (25742293) Rocker Panel Top 9/16 x 25/32 Bottom 5/8 x 25/32 Stem Length: 9/16 Fits Into 3/8 Hole Cadillac DeVille & Seville 2000 On 20972 (11589176) Rocker Panel Top 3/4 x 1-1/32 Bottom 19/32 x 1-1/32 Stem Length: 9/16 Fits Into 3/8 Hole Chevrolet Malibu 20952 (15236894) Rocker Panel Top 9/16 x 23/32 Overall Height: 5/8 Stem Length: 7/16 Fits Into 3/8 Hole, Buick Lucerne and Cadillac CTS & STS 36 THE COM PLETE FAS TENER LINE "SINCE 1916" Copy right 2008, Au-ve-co Prod ucts Co.
(Replaces HNI-211-HNI-225) FEBRUARY 2008 - NEW ITEM BULLETIN NIB-208 Not Actual Size 21013 Yellow Nylon Rocker Panel Top 15/32 x 13/16 Bottom 15/32 x 25/32 Stem Length: 9/16 Fits Into 3/8 Hole Hummer H3 20943 (15014352) Cowl Vent Head Diameter: 14mm Stem Length: 23mm Fits Into 7mm Hole Buick Lucerne 20951 (15236893) Rocker Panel Top 3/4 x 1-9/16 Overall Height: 11/16 Stem Length: 7/16 Fits Into 3/8 Hole Buick Lucerne 20988 (GM: 11589289; Chrysler: 6508863-AA) Air Distributor & Windshield Defroster Stem Length: 17.5mm 2.0mm 4.5mm Fits Into 6.5mm Hole Buick Enclave, Chevrolet Equinox, Chevrolet & GMC S & T Trucks, GMC Acadia And Pontiac Torrent 20950 (10384814) Rocker Panel Top 3/4 x 1-9/16 Overall Height: 1-7/16 Stem Length: 21/32 Fits Into 7/16 Hole Buick Lucerne 20880 (11589290) Air Inlet Grille, Bumper Fascia & Front Brake Caliper Cooling Duct 4.5mm 7.0mm Fits Into 6.5mm Hole Buick Enclave, Cadillac CTS & STS, Chevrolet Cobalt, Equinox & SSR, GM Trucks and Pontiac G5 & Torrent UNIT PACKAGE: 50 20989 (GM: 11589291; Ford: W713331-S300) Air Dam & Grille Stem Length: 22mm 7.0mm 9.5mm Fits Into 6.5mm Hole Cadillac CTS, SRX And STS 20826 (11609417) Fender Apron Head Diameter: 19mm Stem Length: 14mm 2.7mm 5.3mm Buick Enclave & LaCrosse, Cadillac CTS, SRX & STS, Chevrolet Cobalt, Equinox & Malibu, GM Trucks and Pontiac G5, G6 & Torrent UNIT PACKAGE: 50 20990 (GM: 15296830; Chrylser: 5116530-AA) Fascia & General Purpose Head Diameter: 19mm Stem Length: 16mm 5.0mm-7.0mm Fits Into 8mm Hole GM 2007 On 20888 (GM: 11561368; Chrys: 6508712AA) Fender, Wheel & Bumper 3.0mm 5.8mm Fits Into 9.5mm Hole Chevrolet Impala & Monte Carlo And Pontiac Grand Prix & Solstice Jeep Wrangler 2000 - On Copy right 2008, Au-ve-co Prod ucts Co. "SINCE 1916" THE COM PLETE FAS TENER LINE 37
NIB-0208 FEBRUARY 2008 - NEW ITEM BULLETIN (Replaces HNI-211-HNI-225) 20991 (11589292) Bumper Fascia, Flares & Air Dam 2.0mm 4.5mm Chevrolet & GMC C & K Trucks 2007 On 20889 (GM: 11589293 Ford: W712196-S300) Cowl Vent & Fender Stem Length: 22mm 4.5mm - 7.0mm Buick Century, LaCrosse & Regal, Cadillac, Chevrolet Equinox, GM Trucks, Hummer H3 And Pontiac Grand Prix & Torrent 1997 On Ford Edge, Fusion, Lincoln MKX, Milan And Zephyr 20992 (11589294) Bumper Fascia, Fender And Toe/Floor Panel Stem Length: 24mm 7.0mm 10.0mm Buick Enclave & LaCrosse, Chevrolet & GMC C & K Trucks, GMC Acadia, Hummer H3 and Saturn Outlook 20993 (GM: 11589295; Ford: W712665-S300) Fender, Flare, Gas Tank & Panel Attachment Head Diameter: 25mm 3.0mm-6.0mm Fits Into 10.5mm Hole Chevrolet Cobalt & HHR, GM C & K Trucks and Pontiac G5 20994 (GM: 11589296) Panel Attachment & General Purpose Head Diameter: 25mm Stem Length: 23mm 6.0mm 9.0mm Fits Into 10.5mm Hole Buick Enclave and GMC Acadia 2007 On Groove 93 20945 (Strattec: 692931; GM: 89024363, 15824471) Transponder For Anti-Theft Security Chevrolet Impala UNIT PACKAGE: 1 20939 (W711412-S300) Natural Nylon Rear Bumper Screw Grommet M4.2 (#8) Screw Size 9.5mm x 9.5mm Stem Length: 12mm Ford Fusion UNIT PACKAGE: 50 20980 (6G1Z-5410182-D) Gray Nylon Rocker Panel 11mm x 16mm Overall Length: 19mm Ford 500 20979 (6G1Z-5410182-C) Wheel Flare & Rocker Panel Top 14mm x 18mm Bottom 14mm x 18mm Stem Length: 11mm, Ford 500 20981 Not Available From O.E.M. Wheel Flare Top 14mm x 29mm Bottom 14mm x 29mm Stem Length: 16mm Ford Explorer 38 THE COM PLETE FAS TENER LINE "SINCE 1916" Copy right 2008, Au-ve-co Prod ucts Co.
(Replaces HNI-211-HNI-225) FEBRUARY 2008 - NEW ITEM BULLETIN NIB-208 21009 (YL8Z-7820806-AA) Body Side & Rocker Panel Top 13mm x 25mm Bottom 13mm x 18mm Stem Length: 10mm Ford Escape 2001 On 20968 Yellow Nylon Wheel Lip 15mm x 51mm Stem Length: 11mm Fits Into 10mm Hole Ford Expedition & Navigator 1998 On 21000 (F57B-16241-AA) Fender 15mm x 51mm Stem Length: 11mm Fits Into 8mm Hole Ford Explorer & Others 20965 (F4ZZ-6310182-A) Rocker Panel and Ground Effects 16mm x 50mm Stem Length: 14mm Ford Mustang 1995 On 20977 (6G1Z-5410182-A) Gray Nylon Rocker Panel Top 22mm x 30mm Overall Height: 18mm Ford 500 20978 (6G1Z-5410182-B) Gray Nylon Rocker Panel 22mm x 48mm Stem Length: 14mm Ford 500 21024 (5R3Z-54310D12-AAA) Trim Panel Stem Length: 10mm Fits Into 6mm Hole Ford Mustang 20989 (GM: 11589291; Ford: W713331-S300) Air Dam & Grille Stem Length: 22mm 7.0mm 9.5mm Fits Into 6.5mm Hole GM Ford 20889 (GM: 11589293 Ford: W712196-S300) Cowl Vent & Fender Stem Length: 22mm 4.5mm 7.0mm GM 1997 On Ford Edge, Fusion, Lincoln MKX, Milan And Zephyr 20993 (GM: 11589295; Ford: W712665-S300) Fender, Flare, Gas Tank & Panel Attachment Head Diameter: 25mm 3.0mm 6.0mm Fits Into 10.5mm Hole GM Ford 21020 (W701295-S301) Zinc Organic Front Bumper Cover To Air Dam Fastener Width: 13/16 Length: 1-1/16 Ford Focus Copy right 2008, Au-ve-co Prod ucts Co. "SINCE 1916" THE COM PLETE FAS TENER LINE 39
NIB-0208 FEBRUARY 2008 - NEW ITEM BULLETIN (Replaces HNI-211-HNI-225) 20962 (55156879-AB) Tail Light Grommet 20mm x 31mm Receives 10mm Ball Stud Jeep Commander 20964 (5159077-AA) Rear Bumper Clip Stem Length: 15/32 Overall Length: 31/32 Jeep Grand Cherokee 20982 Not Available From O.E.M. Fender & Wheel Flare Top 14mm x 18mm Bottom 17mm x 21mm Jeep Commander 20988 (GM: 11589289; Chrysler: 6508863-AA) Air Distributor & Windshield Defroster Stem Length: 17.5mm 2.0mm 4.5mm Fits Into 6.5mm Hole GM Chrysler 20966 (5160260-AA) Rear Bumper, Tail Light And Fender Bottom Fits Into 8mm Hole Dodge Caliber and Jeep Compass & Patriot 2007 On 20888 (GM: 11561368; Chrys: 6508712AA) Fender, Wheel & Bumper 3.0mm 5.8mm Fits Into 9.5mm Hole GM Jeep Wrangler 2000 On 20990 (GM: 15296830; Chrysler: 5116530-AA) Fascia & General Purpose Head Diameter: 19mm Stem Length: 16mm 5.0mm 7.0mm Fits Into 8mm Hole GM 2007 On Chrysler 20940 (55157330-AC) Tail Light Large Head Diameter: 31mm Small Head Diameter: 20mm Stem Length: 21mm Fits Into 8mm Square Hole Jeep Commander 21021 (0WX68BD5-AA) Gray Nylon Door Trim Panel Head Diameter: 22mm Stem Length: 10mm Chrysler Charger, Magnum & 300M 20948 (OWX68BD1-AA) Tan Nylon Door Trim Panel Head Diameter: 22mm Stem Length: 10mm Chrysler 300M and Dodge Charger & Magnum 40 THE COM PLETE FAS TENER LINE "SINCE 1916" Copy right 2008, Au-ve-co Prod ucts Co.
(Replaces HNI-211-HNI-225) FEBRUARY 2008 - NEW ITEM BULLETIN NIB-208 20967 Rear Bumper Mounting Bracket Head Diameter: 22mm Stem Length: 16mm Fits Into 10mm Hole Jeep Commander 20963 (4806334-AA) Black & White Nylon Rear Bumper Head Diameter: 34mm Shoulder Length: 3.5mm Stem Length: 17mm Dodge Caliber and Jeep Compass & Patriot 2007 On 21019 (6509106-AA) Zinc M6-1.0 Thread Specialty Insert Grip Range:.70mm 3.17mm Head Diameter: 17mm Hex Size: 9.5mm Luggage Rack & Bumper Fascia Chrysler Jeep & Van Can Only be set with Pneumatic Tool 20954 (90682-SEA-003) Fender Apron Grommet Stem Length: 12mm Fits Into 9mm Square Hole Acura TSX and Honda Civic & Odyssey 20959 (91560-S9A-A01) Top Head Diameter: 13mm Middle Head Diameter: 16mm Bottom Head Diameter: 15mm Stem Diameter: 9.5mm Acura TL & TSX and Honda Accord, Civic, CRV & Odyssey 20986 (91505-S9A-003) Front Bumper With Internal Metal Insert Fits Into 10mm Hole Honda Civic 20958 (GJ6A-68-162) 20960 (GM9E-63-938A) 20957 (G6JA-50-0Z5) Natural Nylon 20984 (BC1M-50-0Z5) Natural Nylon Windshield Garnish Front Bumper Front Bumper Moulding Retainer Screw Grommet Screw Grommet Top Windshield Screw Size: M4.2 (#8) M4.2 (#8) Screw Size 10mm x 13mm Bottom Head 17mm x 20mm 23mm x 24mm 24mm x 28mm Diameter: 16mm Stem Length: 21mm Stem Length: 14mm Stem Length: 14mm Stem Length: 33mm Fits Into 8mm Hole Mazda Miata, MPV, RX8 Mazda 323, 626, Miata Fits Into 10mm Hole Mazda 6 3, 5 & 6 MPV & Protégé Mazda 3,5 & RX8 2000 On 1995 On Copy right 2008, Au-ve-co Prod ucts Co. "SINCE 1916" THE COM PLETE FAS TENER LINE 41
NIB-0208 FEBRUARY 2008 - NEW ITEM BULLETIN (Replaces HNI-211-HNI-225) 20909 (124-990-04-92) Head Diameter: 16mm Stem Length: 18mm Fits Into 7mm Hole Mercedes 20961 Drip Top Width: 25mm Overall Height: 16mm Fits Into 5mm Hole Infiniti M45, I30 & G35 Nissan Altima, Maxima & 350Z 20953 (11296-AG000) Front Bumper And Radiator Support Fits Into 8mm Hole Infiniti FX 35/45 and Nissan Altima, Maxima & Quest 21008 (75791-33020) Front & Rear Belt Width: 14mm Overall Height: 10mm Toyota Camry 2000 1997 21016 (75392-35200, 75392-04010) Fender Flare & Bumper Clip 13mm x 26mm Stem Length: 24mm Toyota Camry, FJ, RAV 4 & Tacoma 21015 (52535-50060, 52535-0E010) Front Bumper Screw Grommet M5.5 M6 (#12) Screw Size 17mm x 30mm Stem Length: 9mm Lexus IS250, IS350, RX330 & RX350 and Toyota Camry, Highlander & Tacoma 2001 On UNIT PACKAGE: 5 21011 (90467-07188) Head Diameter: 15mm Stem Length: 17mm Fits Into 7mm Hole Toyota Camry, Tundra & 4-Runner 20955 (90467-07201) Engine Under Cover Stem Length: 10mm Fits Into 7mm Hole Lexus ES300/330 and Toyota Avalon, Camry & Solara 21010 (90467-09166) Stem Length: 9mm Fits Into 9mm Square Hole Toyota Camry 42 THE COM PLETE FAS TENER LINE "SINCE 1916" Copy right 2008, Au-ve-co Prod ucts Co.